CY8C24223A-24PVXIT

PSoC® Mixed-Signal Array CY8C24123A, CY8C24223A, and CY8C24423A Final Data Sheet Features ■ Powerful Harvard Architecture Processor ❐ M8C Processor Speeds to 24 MHz ❐ 8x8 Multiply, 32-Bit Accumulate ❐ Low Power at High Speed ❐ 2.4 to 5.25V Operating Voltage ❐ Operating Voltages Down to 1.0V Using OnChip Switch Mode Pump (SMP) ❐ Industrial Temperature Range: -40°C to +85°C ■ Advanced Peripherals (PSoC Blocks) ❐ 6 Rail-to-Rail Analog PSoC Blocks Provide: - Up to 14-Bit ADCs - Up to 9-Bit DACs - Programmable Gain Amplifiers - Programmable Filters and Comparators ❐ 4 Digital PSoC Blocks Provide: - 8- to 32-Bit Timers, Counters, and PWMs - CRC and PRS Modules - Full-Duplex UART - Multiple SPI™ Masters or Slaves - Connectable to all GPIO Pins ❐ Complex Peripherals by Combining Blocks ■ Precision, Programmable Clocking ❐ Internal ±2.5% 24/48 MHz Oscillator ❐ High-Accuracy 24 MHz with Optional 32 kHz Crystal and PLL ❐ Optional External Oscillator, up to 24 MHz ❐ Internal Oscillator for Watchdog and Sleep ■ Flexible On-Chip Memory ❐ 4K Flash Program Storage 50,000 Erase/Write Cycles ❐ 256 Bytes SRAM Data Storage ❐ In-System Serial Programming (ISSP) ❐ Partial Flash Updates ❐ Flexible Protection Modes ❐ EEPROM Emulation in Flash ■ Programmable Pin Configurations ❐ 25 mA Sink on all GPIO ❐ Pull Up, Pull Down, High Z, Strong, or Open Drain Drive Modes on all GPIO ❐ Up to 10 Analog Inputs on GPIO ❐ Two 30 mA Analog Outputs on GPIO ❐ Configurable Interrupt on all GPIO ■ New CY8C24x23A PSoC Device ❐ Derived from the CY8C24x23 Device ❐ Low Power and Low Voltage (2.4V) ■ Additional System Resources ❐ I2C™ Slave, Master, and Multi-Master to 400 kHz ❐ Watchdog and Sleep Timers ❐ User-Configurable Low Voltage Detection ❐ Integrated Supervisory Circuit ❐ On-Chip Precision Voltage Reference ■ Complete Development Tools ❐ Free Development Software (PSoC Designer™) ❐ Full-Featured, In-Circuit Emulator and Programmer ❐ Full Speed Emulation ❐ Complex Breakpoint Structure ❐ 128K Trace Memory Port 2 Port 1 Port 0 Analog Drivers PSoC® Functional Overview The PSoC® family consists of many Mixed-Signal Array with On-Chip Controller devices. These devices are designed to replace multiple traditional MCU-based system components with one, low cost single-chip programmable device. PSoC devices include configurable blocks of analog and digital logic, as well as programmable interconnects. This architecture allows the user to create customized peripheral configurations that match the requirements of each individual application. Additionally, a fast CPU, Flash program memory, SRAM data memory, and configurable IO are included in a range of convenient pinouts and packages. The PSoC architecture, as illustrated on the left, is comprised of four main areas: PSoC Core, Digital System, Analog System, and System Resources. Configurable global busing allows all the device resources to be combined into a complete custom system. The PSoC CY8C24x23A family can have up to three IO ports that connect to the global digital and analog interconnects, providing access to 4 digital blocks and 6 analog blocks. PSoC CORE System Bus Global Digital Interconnect SRAM 256 Bytes Interrupt Controller Global Analog Interconnect Flash 4K Sleep and Watchdog SROM CPU Core (M8C) Multiple Clock Sources (Includes IMO, ILO, PLL, and ECO) DIGITAL SYSTEM Digital Block Array ANALOG SYSTEM Analog Ref Analog Block Array Analog Input Muxing The PSoC Core The PSoC Core is a powerful engine that supports a rich feature set. The core includes a CPU, memory, clocks, and configurable GPIO (General Purpose IO). The M8C CPU core is a powerful processor with speeds up to 24 MHz, providing a four MIPS 8-bit Harvard architecture micro- Digital Clocks Multiply Accum. Decimator I2C POR and LVD System Resets Internal Voltage Ref. Switch Mode Pump SYSTEM RESOURCES October 17, 2006 © Cypress Semiconductor Corp. 2004-2006 — Document No. 38-12028 Rev. *F 1 [+] [+] Feedback CY8C24x23A Final Data Sheet PSoC® Overview processor. The CPU utilizes an interrupt controller with 11 vectors, to simplify programming of real time embedded events. Program execution is timed and protected using the included Sleep and Watchdog Timers (WDT). Memory encompasses 4 KB of Flash for program storage, 256 bytes of SRAM for data storage, and up to 2 KB of EEPROM emulated using the Flash. Program Flash utilizes four protection levels on blocks of 64 bytes, allowing customized software IP protection. The PSoC device incorporates flexible internal clock generators, including a 24 MHz IMO (internal main oscillator) accurate to 2.5% over temperature and voltage. The 24 MHz IMO can also be doubled to 48 MHz for use by the digital system. A low power 32 kHz ILO (internal low speed oscillator) is provided for the Sleep timer and WDT. If crystal accuracy is desired, the ECO (32.768 kHz external crystal oscillator) is available for use as a Real Time Clock (RTC) and can optionally generate a crystal-accurate 24 MHz system clock using a PLL. The clocks, together with programmable clock dividers (as a System Resource), provide the flexibility to integrate almost any timing requirement into the PSoC device. PSoC GPIOs provide connection to the CPU, digital and analog resources of the device. Each pin’s drive mode may be selected from eight options, allowing great flexibility in external interfacing. Every pin also has the capability to generate a system interrupt on high level, low level, and change from last read. Digital peripheral configurations include those listed below. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ PWMs (8 to 32 bit) PWMs with Dead band (8 to 24 bit) Counters (8 to 32 bit) Timers (8 to 32 bit) UART 8 bit with selectable parity SPI master and slave I2C slave and multi-master (1 available as a System Resource) Cyclical Redundancy Checker/Generator (8 to 32 bit) IrDA Pseudo Random Sequence Generators (8 to 32 bit) The digital blocks can be connected to any GPIO through a series of global buses that can route any signal to any pin. The buses also allow for signal multiplexing and for performing logic operations. This configurability frees your designs from the constraints of a fixed peripheral controller. Digital blocks are provided in rows of four, where the number of blocks varies by PSoC device family. This allows you the optimum choice of system resources for your application. Family resources are shown in the table titled “PSoC Device Characteristics” on page 3. The Analog System The Analog System is composed of 6 configurable blocks, each comprised of an opamp circuit allowing the creation of complex analog signal flows. Analog peripherals are very flexible and can be customized to support specific application requirements. Some of the more common PSoC analog functions (most available as user modules) are listed below. ■ The Digital System The Digital System is composed of 4 digital PSoC blocks. Each block is an 8-bit resource that can be used alone or combined with other blocks to form 8, 16, 24, and 32-bit peripherals, which are called user module references. Port 1 Port 2 Port 0 Analog-to-digital converters (up to 2, with 6- to 14-bit resolution, selectable as Incremental, Delta Sigma, and SAR) Filters (2 and 4 pole band-pass, low-pass, and notch) Amplifiers (up to 2, with selectable gain to 48x) Instrumentation amplifiers (1 with selectable gain to 93x) Comparators (up to 2, with 16 selectable thresholds) DACs (up to 2, with 6- to 9-bit resolution) Multiplying DACs (up to 2, with 6- to 9-bit resolution) High current output drivers (two with 30 mA drive as a PSoC Core resource) 1.3V reference (as a System Resource) DTMF Dialer Modulators Correlators Peak Detectors Many other topologies possible ■ ■ Digital Clocks From Core To System Bus To Analog System ■ ■ DIGITAL SYSTEM Digital PSoC Block Array Row Input Configuration 8 8 ■ ■ 4 8 8 Row 0 DBB00 DBB01 DCB02 ■ ■ ■ ■ Row Output Configuration DCB03 4 GIE[7:0] GIO[7:0] Global Digital Interconnect GOE[7:0] GOO[7:0] ■ ■ ■ Digital System Block Diagram October 17, 2006 Document No. 38-12028 Rev. *F 2 [+] [+] Feedback CY8C24x23A Final Data Sheet PSoC® Overview Analog blocks are arranged in a column of three, which includes one CT (Continuous Time) and two SC (Switched Capacitor) blocks, as shown in the figure below. P0[7] P0[5] P0[3] P0[1] AGNDIn RefIn P0[6] P0[4] P0[2] P0[0] Additional System Resources System Resources, some of which have been previously listed, provide additional capability useful to complete systems. Additional resources include a multiplier, decimator, switch mode pump, low voltage detection, and power on reset. Statements describing the merits of each system resource are below. ■ Digital clock dividers provide three customizable clock frequencies for use in applications. The clocks can be routed to both the digital and analog systems. Additional clocks can be generated using digital PSoC blocks as clock dividers. A multiply accumulate (MAC) provides a fast 8-bit multiplier with 32-bit accumulate, to assist in both general math as well as digital filters. The decimator provides a custom hardware filter for digital signal processing applications including the creation of Delta Sigma ADCs. The I2C module provides 100 and 400 kHz communication over two wires. Slave, master, multi-master are supported. Low Voltage Detection (LVD) interrupts can signal the application of falling voltage levels, while the advanced POR (Power On Reset) circuit eliminates the need for a system supervisor. An internal 1.3V reference provides an absolute reference for the analog system, including ADCs and DACs. An integrated switch mode pump (SMP) generates normal operating voltages from a single 1.2V battery cell, providing a low cost boost converter. ■ P2[6] P2[3] P2[4] P2[2] P2[0] ■ P2[1] ■ ■ Array Input Configuration ■ ACI0[1:0] ACI1[1:0] ■ Block Array ACB00 ASC10 ASD20 ACB01 ASD11 ASC21 PSoC Device Characteristics Depending on your PSoC device characteristics, the digital and analog systems can have 16, 8, or 4 digital blocks and 12, 6, or 4 analog blocks. The following table lists the resources available for specific PSoC device groups. The PSoC device covered by this data sheet is highlighted below. PSoC Device Characteristics Analog Columns Analog Outputs Analog Inputs Analog Blocks Digital Blocks Digital IO Digital Rows SRAM Size 2K 256 Bytes 1K 256 Bytes 256 Bytes 512 Bytes 256 Bytes 512 Bytes PSoC Part Number Flash Size 32K 16K 16K 4K 4K 8K 4K 8K Analog Reference Interface to Digital System RefHi RefLo AGND Reference Generators AGNDIn RefIn Bandgap CY8C29x66 CY8C27x43 CY8C24x94 CY8C24x23 CY8C24x23A CY8C21x34 CY8C21x23 CY8C20x34 up to 64 up to 44 49 up to 24 up to 24 up to 28 16 up to 28 4 2 1 1 1 1 1 0 16 8 4 4 4 4 4 0 12 12 48 12 12 28 8 28 4 4 2 2 2 0 0 0 4 4 2 2 2 2 2 0 12 12 6 6 6 4a 4a 3b M8C Interface (Address Bus, Data Bus, Etc.) Analog System Block Diagram a. Limited analog functionality. b. Two analog blocks and one CapSense. October 17, 2006 Document No. 38-12028 Rev. *F 3 [+] [+] Feedback CY8C24x23A Final Data Sheet PSoC® Overview Getting Started The quickest path to understanding the PSoC silicon is by reading this data sheet and using the PSoC Designer Integrated Development Environment (IDE). This data sheet is an overview of the PSoC integrated circuit and presents specific pin, register, and electrical specifications. For in-depth information, along with detailed programming information, reference the PSoC Mixed-Signal Array Technical Reference Manual. For up-to-date Ordering, Packaging, and Electrical Specification information, reference the latest PSoC device data sheets on the web at http://www.cypress.com/psoc. Development Tools PSoC Designer is a Microsoft® Windows-based, integrated development environment for the Programmable System-onChip (PSoC) devices. The PSoC Designer IDE and application runs on Windows NT 4.0, Windows 2000, Windows Millennium (Me), or Windows XP. (Reference the PSoC Designer Functional Flow diagram below.) PSoC Designer helps the customer to select an operating configuration for the PSoC, write application code that uses the PSoC, and debug the application. This system provides design database management by project, an integrated debugger with In-Circuit Emulator, in-system programming support, and the CYASM macro assembler for the CPUs. PSoC Designer also supports a high-level C language compiler developed specifically for the devices in the family. Development Kits Development Kits are available from the following distributors: Digi-Key, Avnet, Arrow, and Future. The Cypress Online Store contains development kits, C compilers, and all accessories for PSoC development. Go to the Cypress Online Store web site at http://www.cypress.com, click the Online Store shopping cart icon at the bottom of the web page, and click PSoC (Programmable System-on-Chip) to view a current list of available items. PSoC Designer Graphical Designer Interface Context Sensitive Help Commands Results Technical Training Free PSoC technical training is available for beginners and is taught by a marketing or application engineer over the phone. PSoC training classes cover designing, debugging, advanced analog, as well as application-specific classes covering topics such as PSoC and the LIN bus. Go to http://www.cypress.com, click on Design Support located on the left side of the web page, and select Technical Training for more details. Importable Design Database Device Database Application Database Project Database User Modules Library Consultants Certified PSoC Consultants offer everything from technical assistance to completed PSoC designs. To contact or become a PSoC Consultant go to http://www.cypress.com, click on Design Support located on the left side of the web page, and select CYPros Consultants. PSoC Designer Core Engine PSoC Configuration Sheet Manufacturing Information File Technical Support PSoC application engineers take pride in fast and accurate response. They can be reached with a 4-hour guaranteed response at http://www.cypress.com/support/login.cfm. Emulation Pod In-Circuit Emulator Device Programmer Application Notes A long list of application notes will assist you in every aspect of your design effort. To view the PSoC application notes, go to the http://www.cypress.com web site and select Application Notes under the Design Resources list located in the center of the web page. Application notes are listed by date as default. PSoC Designer Subsystems October 17, 2006 Document No. 38-12028 Rev. *F 4 [+] [+] Feedback CY8C24x23A Final Data Sheet PSoC® Overview PSoC Designer Software Subsystems Device Editor The Device Editor subsystem allows the user to select different onboard analog and digital components called user modules using the PSoC blocks. Examples of user modules are ADCs, DACs, Amplifiers, and Filters. The device editor also supports easy development of multiple configurations and dynamic reconfiguration. Dynamic configuration allows for changing configurations at run time. PSoC Designer sets up power-on initialization tables for selected PSoC block configurations and creates source code for an application framework. The framework contains software to operate the selected components and, if the project uses more than one operating configuration, contains routines to switch between different sets of PSoC block configurations at run time. PSoC Designer can print out a configuration sheet for a given project configuration for use during application programming in conjunction with the Device Data Sheet. Once the framework is generated, the user can add application-specific code to flesh out the framework. It’s also possible to change the selected components and regenerate the framework. Debugger The PSoC Designer Debugger subsystem provides hardware in-circuit emulation, allowing the designer to test the program in a physical system while providing an internal view of the PSoC device. Debugger commands allow the designer to read and program and read and write data memory, read and write IO registers, read and write CPU registers, set and clear breakpoints, and provide program run, halt, and step control. The debugger also allows the designer to create a trace buffer of registers and memory locations of interest. Online Help System The online help system displays online, context-sensitive help for the user. Designed for procedural and quick reference, each functional subsystem has its own context-sensitive help. This system also provides tutorials and links to FAQs and an Online Support Forum to aid the designer in getting started. Hardware Tools In-Circuit Emulator Design Browser The Design Browser allows users to select and import preconfigured designs into the user’s project. Users can easily browse a catalog of preconfigured designs to facilitate time-to-design. Examples provided in the tools include a 300-baud modem, LIN Bus master and slave, fan controller, and magnetic card reader. A low cost, high functionality ICE (In-Circuit Emulator) is available for development support. This hardware has the capability to program single devices. The emulator consists of a base unit that connects to the PC by way of the parallel or USB port. The base unit is universal and will operate with all PSoC devices. Emulation pods for each device family are available separately. The emulation pod takes the place of the PSoC device in the target board and performs full speed (24 MHz) operation. Application Editor In the Application Editor you can edit your C language and Assembly language source code. You can also assemble, compile, link, and build. Assembler. The macro assembler allows the assembly code to be merged seamlessly with C code. The link libraries automatically use absolute addressing or can be compiled in relative mode, and linked with other software modules to get absolute addressing. C Language Compiler. A C language compiler is available that supports PSoC family devices. Even if you have never worked in the C language before, the product quickly allows you to create complete C programs for the PSoC family devices. The embedded, optimizing C compiler provides all the features of C tailored to the PSoC architecture. It comes complete with embedded libraries providing port and bus operations, standard keypad and display support, and extended math functionality. October 17, 2006 Document No. 38-12028 Rev. *F 5 [+] [+] Feedback CY8C24x23A Final Data Sheet PSoC® Overview Designing with User Modules The development process for the PSoC device differs from that of a traditional fixed function microprocessor. The configurable analog and digital hardware blocks give the PSoC architecture a unique flexibility that pays dividends in managing specification change during development and by lowering inventory costs. These configurable resources, called PSoC Blocks, have the ability to implement a wide variety of user-selectable functions. Each block has several registers that determine its function and connectivity to other blocks, multiplexers, buses and to the IO pins. Iterative development cycles permit you to adapt the hardware as well as the software. This substantially lowers the risk of having to select a different part to meet the final design requirements. To speed the development process, the PSoC Designer Integrated Development Environment (IDE) provides a library of pre-built, pre-tested hardware peripheral functions, called “User Modules.” User modules make selecting and implementing peripheral devices simple, and come in analog, digital, and mixed signal varieties. The standard User Module library contains over 50 common peripherals such as ADCs, DACs Timers, Counters, UARTs, and other not-so common peripherals such as DTMF Generators and Bi-Quad analog filter sections. Each user module establishes the basic register settings that implement the selected function. It also provides parameters that allow you to tailor its precise configuration to your particular application. For example, a Pulse Width Modulator User Module configures one or more digital PSoC blocks, one for each 8 bits of resolution. The user module parameters permit you to establish the pulse width and duty cycle. User modules also provide tested software to cut your development time. The user module application programming interface (API) provides highlevel functions to control and respond to hardware events at run-time. The API also provides optional interrupt service routines that you can adapt as needed. The API functions are documented in user module data sheets that are viewed directly in the PSoC Designer IDE. These data sheets explain the internal operation of the user module and provide performance specifications. Each data sheet describes the use of each user module parameter and documents the setting of each register controlled by the user module. The development process starts when you open a new project and bring up the Device Editor, a graphical user interface (GUI) for configuring the hardware. You pick the user modules you need for your project and map them onto the PSoC blocks with point-and-click simplicity. Next, you build signal chains by interconnecting user modules to each other and the IO pins. At this stage, you also configure the clock source connections and enter parameter values directly or by selecting values from drop-down menus. When you are ready to test the hardware configuration or move on to developing code for the project, you perform the “Generate Application” step. This causes PSoC Designer to generate source code that automatically configures the device to your specification and provides the high-level user module API functions. Device Editor User Module Selection Placement and Parameterization Source Code Generator Generate Application Application Editor Project Manager Source Code Editor Build Manager Build All Debugger Interface to ICE Storage Inspector Event & Breakpoint Manager User Module and Source Code Development Flows The next step is to write your main program, and any sub-routines using PSoC Designer’s Application Editor subsystem. The Application Editor includes a Project Manager that allows you to open the project source code files (including all generated code files) from a hierarchal view. The source code editor provides syntax coloring and advanced edit features for both C and assembly language. File search capabilities include simple string searches and recursive “grep-style” patterns. A single mouse click invokes the Build Manager. It employs a professional-strength “makefile” system to automatically analyze all file dependencies and run the compiler and assembler as necessary. Project-level options control optimization strategies used by the compiler and linker. Syntax errors are displayed in a console window. Double clicking the error message takes you directly to the offending line of source code. When all is correct, the linker builds a HEX file image suitable for programming. The last step in the development process takes place inside the PSoC Designer’s Debugger subsystem. The Debugger downloads the HEX image to the In-Circuit Emulator (ICE) where it runs at full speed. Debugger capabilities rival those of systems costing many times more. In addition to traditional single-step, run-to-breakpoint and watch-variable features, the Debugger provides a large trace buffer and allows you define complex breakpoint events that include monitoring address and data bus values, memory locations and external signals. October 17, 2006 Document No. 38-12028 Rev. *F 6 [+] [+] Feedback CY8C24x23A Final Data Sheet PSoC® Overview Document Conventions Acronyms Used The following table lists the acronyms that are used in this document. Acronym AC ADC API CPU CT DAC DC ECO EEPROM FSR GPIO GUI HBM ICE ILO IMO IO IPOR LSb LVD MSb PC PLL POR PPOR PSoC® PWM SC SLIMO SMP SRAM alternating current analog-to-digital converter application programming interface central processing unit continuous time digital-to-analog converter direct current external crystal oscillator electrically erasable programmable read-only memory full scale range general purpose IO graphical user interface human body model in-circuit emulator internal low speed oscillator internal main oscillator input/output imprecise power on reset least-significant bit low voltage detect most-significant bit program counter phase-locked loop power on reset precision power on reset Programmable System-on-Chip™ pulse width modulator switched capacitor slow IMO switch mode pump static random access memory Description Table of Contents For an in depth discussion and more information on your PSoC device, obtain the PSoC Mixed-Signal Array Technical Reference Manual. This document encompasses and is organized into the following chapters and sections. 1. Pin Information ........................................................................................ 8 1.1 Pinouts 1.1.1 1.1.2 1.1.3 1.1.4 1.1.5 ........................................................................................... 8 8-Pin Part Pinout ............................................................. 8 20-Pin Part Pinout ........................................................... 9 28-Pin Part Pinout ......................................................... 10 32-Pin Part Pinout ......................................................... 11 56-Pin Part Pinout ......................................................... 12 2. Register Reference ................................................................................ 14 2.1 Register Conventions ................................................................... 14 2.1.1 Abbreviations Used ....................................................... 14 2.2 Register Mapping Tables ............................................................. 14 Electrical Specifications ....................................................................... 17 3.1 Absolute Maximum Ratings ........................................................ 18 3.2 Operating Temperature ............................................................... 18 3.3 DC Electrical Characteristics ........................................................ 19 3.3.1 DC Chip-Level Specifications ........................................ 19 3.3.2 DC General Purpose IO Specifications ......................... 20 3.3.3 DC Operational Amplifier Specifications ....................... 21 3.3.4 DC Low Power Comparator Specifics ........................... 23 3.3.5 DC Analog Output Buffer Specifications ....................... 24 3.3.6 DC Switch Mode Pump Specifications .......................... 26 3.3.7 DC Analog Reference Specifications ............................ 27 3.3.8 DC Analog PSoC Block Specifications .......................... 28 3.3.9 DC POR, SMP, and LVD Specifications ....................... 29 3.3.10 DC Programming Specifications ................................... 30 3.4 AC Electrical Characteristics ........................................................ 31 3.4.1 AC Chip-Level Specifications ........................................ 31 3.4.2 AC General Purpose IO Specifications ......................... 34 3.4.3 AC Operational Amplifier Specifications ........................ 35 3.4.4 AC Low Power Comparator Specifications ................... 38 3.4.5 AC Digital Block Specifications ..................................... 38 3.4.6 AC Analog Output Buffer Specifications ........................ 40 3.4.7 AC External Clock Specifications .................................. 41 3.4.8 AC Programming Specifications .................................... 42 3.4.9 AC I2C Specifications .................................................... 43 Packaging Information .......................................................................... 44 4.1 Packaging Dimensions ................................................................. 44 4.2 Thermal Impedances .................................................................. 49 4.3 Capacitance on Crystal Pins ....................................................... 50 4.4 Solder Reflow Peak Temperature ................................................ 50 Development Tool Selection ................................................................ 51 5.1 Software ....................................................................................... 51 5.1.1 PSoC Designer .............................................................. 51 5.1.2 PSoC Express ............................................................... 51 5.1.3 PSoC Programmer ........................................................ 51 5.1.4 CY3202-C iMAGEcraft C Compiler ............................... 51 5.2 Development Kits ......................................................................... 51 5.2.1 CY3215-DK Basic Development Kit .............................. 51 5.2.2 CY3210-ExpressDK Development Kit ........................... 52 5.3 Evaluation Tools ........................................................................... 52 5.3.1 CY3210-MiniProg1 ........................................................ 52 5.3.2 CY3210-PSoCEval1 ...................................................... 52 5.3.3 CY3214-PSoCEvalUSB ................................................ 52 5.4 Device Programmers ................................................................... 52 5.4.1 CY3216 Modular Programmer ...................................... 52 5.4.2 CY3207ISSP In-System Programmer ............................ 52 5.5 Accessories (Emulation and Programming) ................................. 53 5.6 3rd-Party Tools ............................................................................. 53 5.7 Build a PSoC Emulator into Your Board ...................................... 53 Ordering Information ............................................................................ 54 6.1 Ordering Code Definitions ............................................................ 54 Sales and Company Information ......................................................... 55 7.1 Copyrights and Code Protection .................................................. 55 3. 4. 5. Units of Measure A units of measure table is located in the Electrical Specifications section. Table 3-1 on page 17 lists all the abbreviations used to measure the PSoC devices. Numeric Naming Hexidecimal numbers are represented with all letters in uppercase with an appended lowercase ‘h’ (for example, ‘14h’ or ‘3Ah’). Hexidecimal numbers may also be represented by a ‘0x’ prefix, the C coding convention. Binary numbers have an appended lowercase ‘b’ (e.g., 01010100b’ or ‘01000011b’). Numbers not indicated by an ‘h’ or ‘b’ are decimal. 6. 7. October 17, 2006 Document No. 38-12028 Rev. *F 7 [+] [+] Feedback 1. Pin Information This chapter describes, lists, and illustrates the CY8C24x23A PSoC device pins and pinout configurations. 1.1 Pinouts The CY8C24x23A PSoC device is available in a variety of packages which are listed and illustrated in the following tables. Every port pin (labeled with a “P”) is capable of Digital IO. However, Vss, Vdd, SMP, and XRES are not capable of Digital IO. 1.1.1 Pin No. 1 2 3 4 5 6 7 8 IO IO IO 8-Pin Part Pinout Type Table 1-1. 8-Pin Part Pinout (PDIP, SOIC) Digital IO IO IO Power Analog IO IO Pin Name P0[5] P0[3] P1[1] Vss P1[0] Description Analog column mux input and column output. Analog column mux input and column output. Crystal Input (XTALin), I2C Serial Clock (SCL), ISSP-SCLK*. Ground connection. Crystal Output (XTALout), I2C Serial Data (SDA), ISSP-SDATA*. Analog column mux input. Analog column mux input. Supply voltage. CY8C24123A 8-Pin PSoC Device A, IO, P0[5] A, IO, P0[3] I2CSCL,XTALin, P1[1] Vss 1 8 2PDIP 7 3SOIC6 4 5 Vdd P0[4], A, I P0[2], A, I P1[0],XTALout,I2CSDA I I Power P0[2] P0[4] Vdd LEGEND: A = Analog, I = Input, and O = Output. * These are the ISSP pins, which are not High Z at POR (Power On Reset). See the PSoC Mixed-Signal Array Technical Reference Manual for details. October 17, 2006 Document No. 38-12028 Rev. *F 8 [+] [+] Feedback CY8C24x23A Final Data Sheet 1. Pin Information 1.1.2 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 IO IO IO IO IO IO IO IO IO IO IO IO 20-Pin Part Pinout Type Table 1-2. 20-Pin Part Pinout (PDIP, SSOP, SOIC) Digital IO IO IO IO Power Analog I IO IO I Pin Name P0[7] P0[5] P0[3] P0[1] SMP P1[7] P1[5] P1[3] P1[1] Description Analog column mux input. Analog column mux input and column output. Analog column mux input and column output. Analog column mux input. Switch Mode Pump (SMP) connection to external components required. I2C Serial Clock (SCL). I2C Serial Data (SDA). Crystal Input (XTALin), I2C Serial Clock (SCL), ISSP-SCLK*. Ground connection. Crystal Output (XTALout), I2C Serial Data (SDA), ISSP-SDATA*. Optional External Clock Input (EXTCLK). Active high external reset with internal pull down. Analog column mux input. Analog column mux input. Analog column mux input. Analog column mux input. Supply voltage. CY8C24223A 20-Pin PSoC Device A, I, P0[7] A, IO, P0[5] A, IO, P0[3] A, I, P0[1] SMP I2CSCL,P1[7] I2C SDA,P1[5] P1[3] I2CSCL, XTALin,P1[1] Vss 1 2 3 4 5 6 7 8 9 10 PDIP SSOP SOIC 20 19 18 17 16 15 14 13 12 11 Vdd P0[6], A, I P0[4], A, I P0[2], A, I P0[0], A, I XRES P1[6] P1[4],EXTCLK P1[2] P1[0],XTALout,I2CSDA Power Vss P1[0] P1[2] P1[4] P1[6] Input I I I I Power XRES P0[0] P0[2] P0[4] P0[6] Vdd LEGEND: A = Analog, I = Input, and O = Output. * These are the ISSP pins, which are not High Z at POR (Power On Reset). See the PSoC Mixed-Signal Array Technical Reference Manual for details. October 17, 2006 Document No. 38-12028 Rev. *F 9 [+] [+] Feedback CY8C24x23A Final Data Sheet 1. Pin Information 1.1.3 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO 28-Pin Part Pinout Type Table 1-3. 28-Pin Part Pinout (PDIP, SSOP, SOIC) Digital IO IO IO IO IO IO IO IO Power I I Analog I IO IO I Pin Name P0[7] P0[5] P0[3] P0[1] P2[7] P2[5] P2[3] P2[1] SMP P1[7] P1[5] P1[3] P1[1] Description Analog column mux input. Analog column mux input and column output. Analog column mux input and column output. Analog column mux input. CY8C24423A 28-Pin PSoC Device A, I, P0[7] A, IO, P0[5] A, IO, P0[3] A, I, P0[1] P2[7] P2[5] A, I, P2[3] A, I, P2[1] SMP I2CSCL,P1[7] I2CSDA, P1[5] P1[3] I2CSCL,XTALin, P1[1] Vss Direct switched capacitor block input. Direct switched capacitor block input. Switch Mode Pump (SMP) connection to external components required. I2C Serial Clock (SCL). I2C Serial Data (SDA). Crystal Input (XTALin), I2C Serial Clock (SCL), ISSP-SCLK*. Ground connection. Crystal Output (XTALout), I2C Serial Data (SDA), ISSP-SDATA*. Optional External Clock Input (EXTCLK). Active high external reset with internal pull down. Direct switched capacitor block input. Direct switched capacitor block input. External Analog Ground (AGND). External Voltage Reference (VRef). Analog column mux input. Analog column mux input. Analog column mux input. Analog column mux input. Supply voltage. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PDIP SSOP SOIC 28 27 26 25 24 23 22 21 20 19 18 17 16 15 Vdd P0[6], A, I P0[4], A, I P0[2], A, I P0[0], A, I P2[6],ExternalVRef P2[4],ExternalAGND P2[2], A, I P2[0], A, I XRES P1[6] P1[4],EXTCLK P1[2] P1[0],XTALout,I2CSDA Power Vss P1[0] P1[2] P1[4] P1[6] Input I I XRES P2[0] P2[2] P2[4] P2[6] I I I I P0[0] P0[2] P0[4] P0[6] Vdd Power LEGEND: A = Analog, I = Input, and O = Output. * These are the ISSP pins, which are not High Z at POR (Power On Reset). See the PSoC Mixed-Signal Array Technical Reference Manual for details. October 17, 2006 Document No. 38-12028 Rev. *F 10 [+] [+] Feedback CY8C24x23A Final Data Sheet 1. Pin Information 1.1.4 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO 32-Pin Part Pinout Type Table 1-4. 32-Pin Part Pinout (QFN**) Digital IO IO IO IO Power Power I I Analog Pin Name P2[7] P2[5] P2[3] P2[1] Vss SMP P1[7] P1[5] NC P1[3] P1[1] Description CY8C24423A 32-Pin PSoC Device P0[1], A, I P0[3], A, IO P0[5], A, IO P0[7], A, I Vdd P0[6], A, I P2[7] P2[5] A, I, P2[3] A, I, P2[1] Vss SMP I2CSCL, P1[7] I2CSDA, P1[5] 1 2 3 4 5 6 7 8 P0[4], A, I NC 24 23 22 21 20 19 18 17 P0[2], A, I P0[0], A, I P2[6],External VRef P2[4],External AGND P2[2], A, I P2[0], A, I XRES P1[6] Direct switched capacitor block input. Direct switched capacitor block input. Switch Mode Pump (SMP) connection to external components required. I2C Serial Clock (SCL). I2C Serial Data (SDA). No connection. Crystal Input (XTALin), I2C Serial Clock (SCL), ISSP-SCLK*. Ground connection. Crystal Output (XTALout), I2C Serial Data (SDA), ISSP-SDATA*. Optional External Clock Input (EXTCLK). No connection. Active high external reset with internal pull down. Direct switched capacitor block input. Direct switched capacitor block input. External Analog Ground (AGND). External Voltage Reference (VRef). Analog column mux input. Analog column mux input. No connection. Analog column mux input. Analog column mux input. Supply voltage. Analog column mux input. Analog column mux input and column output. Analog column mux input and column output. Analog column mux input. Ground connection. P1[0] P1[2] P1[4] NC P1[6] Input I I XRES P2[0] P2[2] P2[4] P2[6] I I I I Power I IO IO I P0[0] P0[2] NC P0[4] P0[6] Vdd P0[7] P0[5] P0[3] P0[1] LEGEND: A = Analog, I = Input, and O = Output. * These are the ISSP pins, which are not High Z at POR (Power On Reset). See the PSoC Mixed-Signal Array Technical Reference Manual for details. ** The center pad on the QFN package should be connected to ground (Vss) for best mechanical, thermal, and electrical performance. If not connected to ground, it should be electrically floated and not connected to any other signal. October 17, 2006 Document No. 38-12028 Rev. *F NC P1[3] Power Vss 9 10 I2CSCL,XTALin,P1[1] 11 Vss 12 I2CSDA,XTALout,P1[0] 13 P1[2] 14 EXTCLK,P1[4] 15 NC 16 32 31 30 29 28 27 26 25 QFN (Top View ) 11 [+] [+] Feedback CY8C24x23A Final Data Sheet 1. Pin Information 1.1.5 56-Pin Part Pinout The 56-pin SSOP part is for the CY8C24000A On-Chip Debug (OCD) PSoC device. Note This part is only used for in-circuit debugging. It is NOT available for production. Table 1-5. 56-Pin Part Pinout (SSOP) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 OCD OCD IO IO IO IO IO IO IO IO IO IO IO IO IO IO Input IO IO Power IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO OCD OCD Power I I I I I I I I Type Digital Analog Pin Name NC P0[7] P0[5] P0[3] P0[1] P2[7] P2[5] P2[3] P2[1] P4[7] P4[5] P4[3] P4[1] OCDE OCDO SMP P3[7] P3[5] P3[3] P3[1] P5[3] P5[1] P1[7] P1[5] NC P1[3] P1[1] Vdd NC NC P1[0] P1[2] P1[4] P1[6] P5[0] P5[2] P3[0] P3[2] P3[4] P3[6] XRES HCLK CCLK P4[0] P4[2] P4[4] P4[6] No connection. Description CY8C24000A 56-Pin PSoC Device NC AI, P0[7] AIO, P0[5] AIO, P0[3] AI, P0[1] P2[7] P2[5] AI, P2[3] AI, P2[1] P4[7] P4[5] P4[3] P4[1] OCDE OCDO SMP P3[7] P3[5] P3[3] P3[1] P5[3] P5[1] I2C SCL, P1[7] I2C SDA, P1[5] NC P1[3] SCLK, I2C SCL, XTALIn, P1[1] Vss 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 Analog column mux input. Analog column mux input and column output. Analog column mux input and column output. Analog column mux input. Direct switched capacitor block input. Direct switched capacitor block input. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 SSOP OCD even data IO. OCD odd data output. Switch Mode Pump (SMP) connection to required external components. Vdd P0[6], AI P0[4], AIO P0[2], AIO P0[0], AI P2[6], External VRef P2[4], External AGND P2[2], AI P2[0], AI P4[6] P4[4] P4[2] P4[0] CCLK HCLK XRES P3[6] P3[4] P3[2] P3[0] P5[2] P5[0] P1[6] P1[4], EXTCLK P1[2] P1[0], XTALOut, I2C SDA, SDATA NC NC Not for Production I2C Serial Clock (SCL). I2C Serial Data (SDA). No connection. Crystal Input (XTALin), I2C Serial Clock (SCL), ISSP-SCLK*. Supply voltage. No connection. No connection.. Crystal Output (XTALout), I2C Serial Data (SDA), ISSP-SDATA*. Optional External Clock Input (EXTCLK). Active high external reset with internal pull down. OCD high-speed clock output. OCD CPU clock output. October 17, 2006 Document No. 38-12028 Rev. *F 12 [+] [+] Feedback CY8C24x23A Final Data Sheet 1. Pin Information Table 1-5. 56-Pin Part Pinout (SSOP) 48 49 50 51 52 53 54 55 56 IO IO IO IO IO IO IO IO Power I I I I I I P2[0] P2[2] P2[4] P2[6] P0[0] P0[2] P0[4] P0[6] Vdd Direct switched capacitor block input. Direct switched capacitor block input. External Analog Ground (AGND). External Voltage Reference (VRef). Analog column mux input. Analog column mux input and column output. Analog column mux input and column output. Analog column mux input. Supply voltage. LEGEND: A = Analog, I = Input, O = Output, and OCD = On-Chip Debug. * These are the ISSP pins, which are not High Z at POR (Power On Reset). See the PSoC Mixed-Signal Array Technical Reference Manual for details. October 17, 2006 Document No. 38-12028 Rev. *F 13 [+] [+] Feedback 2. Register Reference This chapter lists the registers of the CY8C24x23A PSoC device. For detailed register information, reference the PSoC Mixed-Signal Array Technical Reference Manual. 2.1 2.1.1 Register Conventions Abbreviations Used 2.2 Register Mapping Tables The register conventions specific to this section are listed in the following table. Convention R W L C # Description Read register or bit(s) Write register or bit(s) Logical register or bit(s) Clearable register or bit(s) Access is bit specific The PSoC device has a total register address space of 512 bytes. The register space is referred to as IO space and is divided into two banks. The XOI bit in the Flag register (CPU_F) determines which bank the user is currently in. When the XOI bit is set the user is in Bank 1. Note In the following register mapping tables, blank fields are reserved and should not be accessed. October 17, 2006 Document No. 38-12028 Rev. *F 14 [+] [+] Feedback CY8C24x23A Final Data Sheet 2. Register Reference Register Map Bank 0 Table: User Space Access Access Access Access Addr (0,Hex) Addr (0,Hex) Addr (0,Hex) Addr (0,Hex) Name PRT0DR PRT0IE PRT0GS PRT0DM2 PRT1DR PRT1IE PRT1GS PRT1DM2 PRT2DR PRT2IE PRT2GS PRT2DM2 Name Name Name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lank fields are Reserved and should not be accessed. 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F ASD20CR0 90 ASD20CR1 91 ASD20CR2 92 ASD20CR3 93 ASC21CR0 94 ASC21CR1 95 ASC21CR2 96 ASC21CR3 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF RDI0RI B0 RDI0SYN B1 RDI0IS B2 RDI0LT0 B3 RDI0LT1 B4 RDI0RO0 B5 RDI0RO1 B6 B7 B8 B9 BA BB BC BD BE BF # Access is bit specific. ASC10CR0 ASC10CR1 ASC10CR2 ASC10CR3 ASD11CR0 ASD11CR1 ASD11CR2 ASD11CR3 RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW I2C_CFG I2C_SCR I2C_DR I2C_MSCR INT_CLR0 INT_CLR1 INT_CLR3 INT_MSK3 INT_MSK0 INT_MSK1 INT_VC RES_WDT DEC_DH DEC_DL DEC_CR0 DEC_CR1 MUL_X MUL_Y MUL_DH MUL_DL ACC_DR1 ACC_DR0 ACC_DR3 ACC_DR2 RW RW RW RW RW RW RW CPU_F CPU_SCR1 CPU_SCR0 C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF RW # RW # RW RW RW RW RW RW RC W RC RC RW RW W W R R RW RW RW RW RL # # October 17, 2006 Document No. 38-12028 Rev. *F 15 [+] [+] Feedback CY8C24x23A Final Data Sheet 2. Register Reference Register Map Bank 1 Table: Configuration Space Access Access Access Access Addr (1,Hex) Addr (1,Hex) Addr (1,Hex) Addr (1,Hex) Name PRT0DM0 PRT0DM1 PRT0IC0 PRT0IC1 PRT1DM0 PRT1DM1 PRT1IC0 PRT1IC1 PRT2DM0 PRT2DM1 PRT2IC0 PRT2IC1 Name Name Name 00 RW 40 01 RW 41 02 RW 42 03 RW 43 04 RW 44 05 RW 45 06 RW 46 07 RW 47 08 RW 48 09 RW 49 0A RW 4A 0B RW 4B 0C 4C 0D 4D 0E 4E 0F 4F 10 50 11 51 12 52 13 53 14 54 15 55 16 56 17 57 18 58 19 59 1A 5A 1B 5B 1C 5C 1D 5D 1E 5E 1F 5F DBB00FN 20 RW CLK_CR0 60 RW DBB00IN 21 RW CLK_CR1 61 RW DBB00OU 22 RW ABF_CR0 62 RW 23 AMD_CR0 63 RW DBB01FN 24 RW 64 DBB01IN 25 RW 65 DBB01OU 26 RW AMD_CR1 66 RW 27 ALT_CR0 67 RW DCB02FN 28 RW 68 DCB02IN 29 RW 69 DCB02OU 2A RW 6A 2B 6B DCB03FN 2C RW 6C DCB03IN 2D RW 6D DCB03OU 2E RW 6E 2F 6F 30 ACB00CR3 70 RW 31 ACB00CR0 71 RW 32 ACB00CR1 72 RW 33 ACB00CR2 73 RW 34 ACB01CR3 74 RW 35 ACB01CR0 75 RW 36 ACB01CR1 76 RW 37 ACB01CR2 77 RW 38 78 39 79 3A 7A 3B 7B 3C 7C 3D 7D 3E 7E 3F 7F Blank fields are Reserved and should not be accessed. 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F ASD20CR0 90 ASD20CR1 91 ASD20CR2 92 ASD20CR3 93 ASC21CR0 94 ASC21CR1 95 ASC21CR2 96 ASC21CR3 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF RDI0RI B0 RDI0SYN B1 RDI0IS B2 RDI0LT0 B3 RDI0LT1 B4 RDI0RO0 B5 RDI0RO1 B6 B7 B8 B9 BA BB BC BD BE BF # Access is bit specific. ASC10CR0 ASC10CR1 ASC10CR2 ASC10CR3 ASD11CR0 ASD11CR1 ASD11CR2 ASD11CR3 RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF GDI_O_IN D0 GDI_E_IN D1 GDI_O_OU D2 GDI_E_OU D3 D4 D5 D6 D7 D8 D9 DA DB DC OSC_GO_EN DD OSC_CR4 DE OSC_CR3 DF OSC_CR0 E0 OSC_CR1 E1 OSC_CR2 E2 VLT_CR E3 VLT_CMP E4 E5 E6 E7 IMO_TR E8 ILO_TR E9 BDG_TR EA ECO_TR EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 CPU_F F7 F8 F9 FA FB FC FD CPU_SCR1 FE CPU_SCR0 FF RW RW RW RW RW RW RW RW RW RW RW R W W RW W RL # # October 17, 2006 Document No. 38-12028 Rev. *F 16 [+] [+] Feedback 3. Electrical Specifications This chapter presents the DC and AC electrical specifications of the CY8C24x23A PSoC device. For the most up to date electrical specifications, confirm that you have the most recent data sheet by going to the web at http://www.cypress.com/psoc. Specifications are valid for -40oC ≤ TA ≤ 85oC and TJ ≤ 100oC, except where noted. Refer to Table 3-21 for the electrical specifications on the internal main oscillator (IMO) using SLIMO mode. S L IM O M o d e =1 4.75 Vdd Voltage 3.00 2.40 9 3 kHz 3 MHz C PU F r e q u e n c y 1 2 MHz 2 4 MHz 4.75 Vdd Voltage SLIMO Mode = 0 5.25 5.25 S L IM O M o d e =0 Figure 3-1a. Voltage versus CPU Frequency The following table lists the units of measure that are used in this chapter. Table 3-1: Units of Measure Symbol o C degree Celsius decibels femto farad hertz 1024 bytes 1024 bits kilohertz kilohm megahertz megaohm microampere microfarad microhenry microsecond microvolts microvolts root-mean-square O l id g V a a tin n r pe g io Re Unit of Measure Symbol µW mA ms mV nA ns nV Ω pA pF pp ppm ps sps σ V 3.60 3.00 2.40 9 3 kHz S L IM O S L IM O M o d e =1 M o d e =0 S L IM O S L IM O M o d e =1 M o d e =1 6 MHz IM O F r e q u e n c y 1 2 MHz 2 4 MHz Figure 3-1b. IMO Frequency Trim Options Unit of Measure microwatts milli-ampere milli-second milli-volts nanoampere nanosecond nanovolts ohm picoampere picofarad peak-to-peak parts per million picosecond samples per second sigma: one standard deviation volts dB fF Hz KB Kbit kHz kΩ MHz MΩ µA µF µH µs µV µVrms October 17, 2006 Document No. 38-12028 Rev. *F 17 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.1 Symbol TSTG Absolute Maximum Ratings Description Storage Temperature Min -55 25 Typ Max +100 Units oC Table 3-2. Absolute Maximum Ratings Notes Higher storage temperatures will reduce data retention time. Recommended storage temperature is +25oC ± 25oC. Extended duration storage temperatures above 65oC will degrade reliability. TA Vdd VIO VIOZ IMIO ESD LU Ambient Temperature with Power Applied Supply Voltage on Vdd Relative to Vss DC Input Voltage DC Voltage Applied to Tri-state Maximum Current into any Port Pin Electro Static Discharge Voltage Latch-up Current -40 -0.5 Vss - 0.5 Vss - 0.5 -25 2000 – – – – – – – – +85 +6.0 Vdd + 0.5 Vdd + 0.5 +50 – 200 oC V V V mA V mA Human Body Model ESD. 3.2 Symbol TA TJ Operating Temperature Description Ambient Temperature Junction Temperature Min -40 -40 – – Typ Max +85 +100 o o Table 3-3. Operating Temperature Units C C The temperature rise from ambient to junction is package specific. See “Thermal Impedances” on page 49. The user must limit the power consumption to comply with this requirement. Notes October 17, 2006 Document No. 38-12028 Rev. *F 18 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.3 3.3.1 DC Electrical Characteristics DC Chip-Level Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-4. DC Chip-Level Specifications Symbol Vdd IDD Supply Voltage Supply Current Description Min 2.4 – – 5 Typ Max 5.25 8 V mA Units Notes See DC POR and LVD specifications, Table 319 on page 29. Conditions are Vdd = 5.0V, TA = 25 oC, CPU = 3 MHz, SYSCLK doubler disabled, VC1 = 1.5 MHz, VC2 = 93.75 kHz, VC3 = 93.75 kHz, analog power = off. SLIMO mode = 0. IMO = 24 MHz. Conditions are Vdd = 3.3V, TA = 25 oC, CPU = 3 MHz, SYSCLK doubler disabled, VC1 = 1.5 MHz, VC2 = 93.75 kHz, VC3 = 93.75 kHz, analog power = off. SLIMO mode = 0. IMO = 24 MHz. Conditions are Vdd = 2.7V, TA = 25oC, CPU = 0.75 MHz, SYSCLK doubler disabled, VC1 = 0.375 MHz, VC2 = 23.44 kHz, VC3 = 0.09 kHz, analog power = off. SLIMO mode = 1. IMO = 6 MHz. Conditions are with internal slow speed oscillator, Vdd = 3.3V, -40 oC ≤ TA ≤ 55oC, analog power = off. Conditions are with internal slow speed oscillator, Vdd = 3.3V, 55 oC < TA ≤ 85oC, analog power = off. Conditions are with properly loaded, 1 µW max, 32.768 kHz crystal. Vdd = 3.3V, -40 oC ≤ TA ≤ 55oC, analog power = off. ISBXTLH Sleep (Mode) Current with POR, LVD, Sleep Timer, WDT, and external crystal at high temperature.a Reference Voltage (Bandgap) Reference Voltage (Bandgap) – 5 26 µA Conditions are with properly loaded, 1µW max, 32.768 kHz crystal. Vdd = 3.3 V, 55 oC < TA ≤ 85oC, analog power = off. VREF VREF27 1.28 1.16 1.30 1.30 1.33 1.33 V V Trimmed for appropriate Vdd. Vdd > 3.0V. Trimmed for appropriate Vdd. Vdd = 2.4V to 3.0V. IDD3 Supply Current – 3.3 6.0 mA IDD27 Supply Current – 2 4 mA ISB Sleep (Mode) Current with POR, LVD, Sleep Timer, and WDT.a Sleep (Mode) Current with POR, LVD, Sleep Timer, and WDT at high temperature.a Sleep (Mode) Current with POR, LVD, Sleep Timer, WDT, and external crystal.a – 3 6.5 µA ISBH – 4 25 µA ISBXTL – 4 7.5 µA a. Standby current includes all functions (POR, LVD, WDT, Sleep Time) needed for reliable system operation. This should be compared with devices that have similar functions enabled. October 17, 2006 Document No. 38-12028 Rev. *F 19 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.3.2 DC General Purpose IO Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-5. 5V and 3.3V DC GPIO Specifications Symbol RPU RPD VOH Pull-up Resistor Pull-down Resistor High Output Level Description 4 4 Vdd - 1.0 Min Typ 5.6 5.6 – 8 8 – Max Units kΩ kΩ V IOH = 10 mA, Vdd = 4.75 to 5.25V (maximum 40 mA on even port pins (for example, P0[2], P1[4]), maximum 40 mA on odd port pins (for example, P0[3], P1[5])). 80 mA maximum combined IOH budget. IOL = 25 mA, Vdd = 4.75 to 5.25V (maximum 100 mA on even port pins (for example, P0[2], P1[4]), maximum 100 mA on odd port pins (for example, P0[3], P1[5])). 150 mA maximum combined IOL budget. Vdd = 3.0 to 5.25. Vdd = 3.0 to 5.25. Gross tested to 1 µA. Package and pin dependent. Temp = 25oC. Package and pin dependent. Temp = 25oC. Notes VOL Low Output Level – – 0.75 V VIL VIH VH IIL CIN COUT Input Low Level Input High Level Input Hysterisis Input Leakage (Absolute Value) Capacitive Load on Pins as Input Capacitive Load on Pins as Output – 2.1 – – – – – – 60 1 3.5 3.5 0.8 V V – – 10 10 mV nA pF pF Table 3-6. 2.7V DC GPIO Specifications Symbol RPU RPD VOH Pull-up Resistor Pull-down Resistor High Output Level Description 4 4 Vdd - 0.4 Min Typ 5.6 5.6 – 8 8 – Max Units kΩ kΩ V IOH = 2 mA (6.25 Typ), Vdd = 2.4 to 3.0V (16 mA maximum, 50 mA Typ combined IOH budget). IOL = 11.25 mA, Vdd = 2.4 to 3.0V (90 mA maximum combined IOL budget). Vdd = 2.4 to 3.0. Vdd = 2.4 to 3.0. Gross tested to 1 µA. Package and pin dependent. Temp = 25oC. Package and pin dependent. Temp = 25oC. Notes VOL VIL VIH VH IIL CIN COUT Low Output Level Input Low Level Input High Level Input Hysteresis Input Leakage (Absolute Value) Capacitive Load on Pins as Input Capacitive Load on Pins as Output – – 2.0 – – – – – – – 90 1 3.5 3.5 0.75 0.75 – – – 10 10 V V V mV nA pF pF October 17, 2006 Document No. 38-12028 Rev. *F 20 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.3.3 DC Operational Amplifier Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. The Operational Amplifier is a component of both the Analog Continuous Time PSoC blocks and the Analog Switched Cap PSoC blocks. The guaranteed specifications are measured in the Analog Continuous Time PSoC block. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-7. 5V DC Operational Amplifier Specifications Symbol VOSOA Description Input Offset Voltage (absolute value) Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High TCVOSOA IEBOA CINOA VCMOA Average Input Offset Voltage Drift Input Leakage Current (Port 0 Analog Pins) Input Capacitance (Port 0 Analog Pins) Common Mode Voltage Range Common Mode Voltage Range (high power or high opamp bias) – – – – – – 0.0 0.5 1.6 1.3 1.2 7.0 20 4.5 – – 10 8 7.5 35.0 – 9.5 Vdd Vdd - 0.5 mV mV mV µV/oC pA pF V Gross tested to 1 µA. Package and pin dependent. Temp = 25oC. The common-mode input voltage range is measured through an analog output buffer. The specification includes the limitations imposed by the characteristics of the analog output buffer. Specification is applicable at high power. For all other bias modes (except high power, high opamp bias), minimum is 60 dB. Min Typ Max Units Notes GOLOA Open Loop Gain Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High 60 60 80 Vdd - 0.2 Vdd - 0.2 Vdd - 0.5 – – – – – – – – – 64 – – dB VOHIGHOA High Output Voltage Swing (internal signals) Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High – – – – – – 150 300 600 1200 2400 4600 80 – – – 0.2 0.2 0.5 200 400 800 1600 3200 6400 – V V V V V V µA µA µA µA µA µA dB Vss ≤ VIN ≤ (Vdd - 2.25) or (Vdd - 1.25V) ≤ VIN ≤ Vdd. VOLOWOA Low Output Voltage Swing (internal signals) Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High ISOA Supply Current (including associated AGND buffer) Power = Low, Opamp Bias = High Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High Power = High, Opamp Bias = High PSRROA Supply Voltage Rejection Ratio October 17, 2006 Document No. 38-12028 Rev. *F 21 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications Table 3-8. 3.3V DC Operational Amplifier Specifications Symbol VOSOA Description Input Offset Voltage (absolute value) Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High High Power is 5 Volts Only TCVOSOA IEBOA CINOA VCMOA Average Input Offset Voltage Drift Input Leakage Current (Port 0 Analog Pins) Input Capacitance (Port 0 Analog Pins) Common Mode Voltage Range – – – 0.2 7.0 20 4.5 – 35.0 – 9.5 Vdd - 0.2 µV/oC pA pF V Gross tested to 1 µA. Package and pin dependent. Temp = 25oC. The common-mode input voltage range is measured through an analog output buffer. The specification includes the limitations imposed by the characteristics of the analog output buffer. Specification is applicable at high power. For all other bias modes (except high power, high opamp bias), minimum is 60 dB. – – 1.65 1.32 10 8 mV mV Min Typ Max Units Notes GOLOA Open Loop Gain Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = Low Power = High, Opamp Bias = Low 60 60 80 Vdd - 0.2 Vdd - 0.2 Vdd - 0.2 – – – – – – – – – 64 – – dB VOHIGHOA High Output Voltage Swing (internal signals) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = Low Power = High is 5V only – – – – – – 150 300 600 1200 2400 4600 80 – – – 0.2 0.2 0.2 200 400 800 1600 3200 6400 – V V V V V V µA µA µA µA µA µA dB Vss ≤ VIN ≤ (Vdd - 2.25) or (Vdd - 1.25V) ≤ VIN ≤ Vdd.. VOLOWOA Low Output Voltage Swing (internal signals) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = Low Power = High, Opamp Bias = Low ISOA Supply Current (including associated AGND buffer) Power = Low, Opamp Bias = Low Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = Low Power = High, Opamp Bias = High PSRROA Supply Voltage Rejection Ratio October 17, 2006 Document No. 38-12028 Rev. *F 22 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications Table 3-9. 2.7V DC Operational Amplifier Specifications Symbol VOSOA Description Input Offset Voltage (absolute value) Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High High Power is 5 Volts Only TCVOSOA IEBOA CINOA VCMOA Average Input Offset Voltage Drift Input Leakage Current (Port 0 Analog Pins) Input Capacitance (Port 0 Analog Pins) Common Mode Voltage Range – – – 0.2 7.0 20 4.5 – 35.0 – 9.5 Vdd - 0.2 µV/oC pA pF V Gross tested to 1 µA. Package and pin dependent. Temp = 25oC. The common-mode input voltage range is measured through an analog output buffer. The specification includes the limitations imposed by the characteristics of the analog output buffer. Specification is applicable at high power. For all other bias modes (except high power, high opamp bias), minimum is 60 dB. – – 1.65 1.32 10 8 mV mV Min Typ Max Units Notes GOLOA Open Loop Gain Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = Low Power = High 60 60 80 Vdd - 0.2 Vdd - 0.2 Vdd - 0.2 – – – – – – – – – 64 – – dB VOHIGHOA High Output Voltage Swing (internal signals) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = Low Power = High is 5V only – – – – – – 150 300 600 1200 2400 4600 80 – – – 0.2 0.2 0.2 200 400 800 1600 3200 6400 – V V V V V V µA µA µA µA µA µA dB Vss ≤ VIN ≤ (Vdd - 2.25) or (Vdd - 1.25V) ≤ VIN ≤ Vdd. VOLOWOA Low Output Voltage Swing (internal signals) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = Low Power = High, Opamp Bias = Low ISOA Supply Current (including associated AGND buffer) Power = Low, Opamp Bias = Low Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = Low Power = High, Opamp Bias = High PSRROA Supply Voltage Rejection Ratio 3.3.4 DC Low Power Comparator Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-10. DC Low Power Comparator Specifications Symbol VREFLPC ISLPC VOSLPC LPC supply current LPC voltage offset Description Low power comparator (LPC) reference voltage range – – Min 0.2 – 10 2.5 Typ 40 30 Max Vdd - 1 V µA mV Units Notes October 17, 2006 Document No. 38-12028 Rev. *F 23 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.3.5 DC Analog Output Buffer Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-11. 5V DC Analog Output Buffer Specifications Symbol VOSOB TCVOSOB VCMOB ROUTOB Description Input Offset Voltage (Absolute Value) Average Input Offset Voltage Drift Common-Mode Input Voltage Range Output Resistance Power = Low Power = High VOHIGHOB High Output Voltage Swing (Load = 32 ohms to Vdd/2) Power = Low Power = High VOLOWOB Low Output Voltage Swing (Load = 32 ohms to Vdd/2) Power = Low Power = High ISOB Supply Current Including Bias Cell (No Load) Power = Low Power = High PSRROB Supply Voltage Rejection Ratio – – 52 1.1 2.6 64 5.1 8.8 – mA mA dB VOUT > (Vdd - 1.25). – – – – 0.5 x Vdd - 1.3 0.5 x Vdd - 1.3 V V – – 1 1 – – – – Ω Ω V V – – 0.5 Min 3 +6 – Typ 12 – Vdd - 1.0 Max Units mV µV/°C V Notes 0.5 x Vdd + 1.1 – 0.5 x Vdd + 1.1 – Table 3-12. 3.3V DC Analog Output Buffer Specifications Symbol VOSOB TCVOSOB VCMOB ROUTOB Description Input Offset Voltage (Absolute Value) Average Input Offset Voltage Drift Common-Mode Input Voltage Range Output Resistance Power = Low Power = High VOHIGHOB High Output Voltage Swing (Load = 1k ohms to Vdd/2) Power = Low Power = High VOLOWOB Low Output Voltage Swing (Load = 1k ohms to Vdd/2) Power = Low Power = High ISOB Supply Current Including Bias Cell (No Load) Power = Low Power = High PSRROB Supply Voltage Rejection Ratio – 52 0.8 2.0 64 2.0 4.3 – mA mA dB VOUT > (Vdd - 1.25). – – – – 0.5 x Vdd - 1.0 0.5 x Vdd - 1.0 V V 0.5 x Vdd + 1.0 – 0.5 x Vdd + 1.0 – – – V V – – 1 1 – – Ω Ω – – 0.5 Min 3 +6 Typ 12 – Vdd - 1.0 Max Units mV µV/°C V Notes October 17, 2006 Document No. 38-12028 Rev. *F 24 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications Table 3-13. 2.7V DC Analog Output Buffer Specifications Symbol VOSOB TCVOSOB VCMOB ROUTOB Description Input Offset Voltage (Absolute Value) Average Input Offset Voltage Drift Common-Mode Input Voltage Range Output Resistance Power = Low Power = High VOHIGHOB High Output Voltage Swing (Load = 1k ohms to Vdd/2) Power = Low Power = High VOLOWOB Low Output Voltage Swing (Load = 1k ohms to Vdd/2) Power = Low Power = High ISOB Supply Current Including Bias Cell (No Load) Power = Low Power = High PSRROB Supply Voltage Rejection Ratio – 52 0.8 2.0 64 2.0 4.3 – mA mA dB VOUT > (Vdd - 1.25). – – – – 0.5 x Vdd - 0.7 0.5 x Vdd - 0.7 V V 0.5 x Vdd + 0.2 – 0.5 x Vdd + 0.2 – – – V V – – 1 1 – – Ω Ω – – 0.5 Min 3 +6 Typ 12 – Vdd - 1.0 Max Units mV µV/°C V Notes October 17, 2006 Document No. 38-12028 Rev. *F 25 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.3.6 DC Switch Mode Pump Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-14. DC Switch Mode Pump (SMP) Specifications Symbol VPUMP 5V VPUMP 3V VPUMP 2V IPUMP Description 5V Output Voltage from Pump 3.3V Output Voltage from Pump 2.6V Output Voltage from Pump Available Output Current VBAT = 1.8V, VPUMP = 5.0V VBAT = 1.5V, VPUMP = 3.25V VBAT = 1.3V, VPUMP = 2.55V VBAT5V VBAT3V VBAT2V VBATSTART ∆VPUMP_Line Input Voltage Range from Battery Input Voltage Range from Battery Input Voltage Range from Battery Minimum Input Voltage from Battery to Start Pump 5 8 8 1.8 1.0 1.0 1.2 – – – – – – – – – – 5.0 3.3 3.0 – mA mA mA V V V V Min 4.75 3.00 2.45 Typ 5.0 3.25 2.55 Max 5.25 3.60 2.80 V V V Units Notes Configuration of footnote.a Average, neglecting ripple. SMP trip voltage is set to 5.0V. Configuration of footnote.a Average, neglecting ripple. SMP trip voltage is set to 3.25V. Configuration of footnote.a Average, neglecting ripple. SMP trip voltage is set to 2.55V. Configuration of footnote.a SMP trip voltage is set to 5.0V. SMP trip voltage is set to 3.25V. SMP trip voltage is set to 2.55V. Configuration of footnote.a SMP trip voltage is set to 5.0V. Configuration of footnote.a SMP trip voltage is set to 3.25V. Configuration of footnote.a SMP trip voltage is set to 2.55V. Configuration of footnote.a 0oC ≤ TA ≤ 100. 1.25V at TA = -40oC. Line Regulation (over VBAT range) – 5 – %VO Configuration of footnote.a VO is the “Vdd Value for PUMP Trip” specified by the VM[2:0] setting in the DC POR and LVD Specification, Table 319 on page 29. Configuration of footnote.a VO is the “Vdd Value for PUMP Trip” specified by the VM[2:0] setting in the DC POR and LVD Specification, Table 319 on page 29. Configuration of footnote.a Load is 5 mA. Configuration of footnote.a Load is 5 mA. SMP trip voltage is set to 3.25V. ∆VPUMP_Load Load Regulation – 5 – %VO ∆VPUMP_Ripple E3 E2 FPUMP DCPUMP Output Voltage Ripple (depends on capacitor/load) Efficiency Efficiency Switching Frequency Switching Duty Cycle – 35 100 50 – – mVpp % – – 1.3 50 – – MHz % a. L1 = 2 µH inductor, C1 = 10 µF capacitor, D1 = Schottky diode. See Figure 3-2. D1 Vdd V PUMP L1 V BAT + SMP Battery PSoC Vss C1 Figure 3-2. Basic Switch Mode Pump Circuit October 17, 2006 Document No. 38-12028 Rev. *F 26 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.3.7 DC Analog Reference Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. The guaranteed specifications are measured through the Analog Continuous Time PSoC blocks. The power levels for AGND refer to the power of the Analog Continuous Time PSoC block. The power levels for RefHi and RefLo refer to the Analog Reference Control register. The limits stated for AGND include the offset error of the AGND buffer local to the Analog Continuous Time PSoC block. Reference control power is high. Table 3-15. 5V DC Analog Reference Specifications Symbol BG – – – – – – – – – – – – – – – – – AGND = Vdd/2 AGND = 2 x BandGap AGND = P2[4] (P2[4] = Vdd/2) AGND = BandGap AGND = 1.6 x BandGap AGND Block to Block Variation (AGND = Vdd/2) RefHi = Vdd/2 + BandGap RefHi = 3 x BandGap RefHi = 2 x BandGap + P2[6] (P2[6] = 1.3V) RefHi = P2[4] + BandGap (P2[4] = Vdd/2) RefHi = P2[4] + P2[6] (P2[4] = Vdd/2, P2[6] = 1.3V) RefHi = 3.2 x BandGap RefLo = Vdd/2 – BandGap RefLo = BandGap RefLo = 2 x BandGap - P2[6] (P2[6] = 1.3V) RefLo = P2[4] – BandGap (P2[4] = Vdd/2) RefLo = P2[4]-P2[6] (P2[4] = Vdd/2, P2[6] = 1.3V) Description Bandgap Voltage Reference 1.28 Vdd/2 - 0.04 2 x BG - 0.048 P2[4] - 0.011 BG - 0.009 1.6 x BG - 0.022 -0.034 Min 1.30 Vdd/2 - 0.01 2 x BG - 0.030 P2[4] BG + 0.008 1.6 x BG - 0.010 0.000 Typ 1.33 Vdd/2 + 0.007 2 x BG + 0.024 P2[4] + 0.011 BG + 0.016 1.6 x BG + 0.018 0.034 Max V V V V V V V V V V V V V V V V V V Units Vdd/2 + BG - 0.10 3 x BG - 0.06 2 x BG + P2[6] - 0.113 P2[4] + BG - 0.130 P2[4] + P2[6] - 0.133 3.2 x BG - 0.112 Vdd/2 + BG 3 x BG 2 x BG + P2[6] - 0.018 P2[4] + BG - 0.016 P2[4] + P2[6] - 0.016 3.2 x BG Vdd/2 + BG + 0.10 3 x BG + 0.06 2 x BG + P2[6] + 0.077 P2[4] + BG + 0.098 P2[4] + P2[6]+ 0.100 3.2 x BG + 0.076 Vdd/2 - BG - 0.04 BG - 0.06 2 x BG - P2[6] - 0.084 P2[4] - BG - 0.056 P2[4] - P2[6] - 0.057 Vdd/2 - BG + 0.024 BG 2 x BG - P2[6] + 0.025 P2[4] - BG + 0.026 P2[4] - P2[6] + 0.026 Vdd/2 - BG + 0.04 BG + 0.06 2 x BG - P2[6] + 0.134 P2[4] - BG + 0.107 P2[4] - P2[6] + 0.110 Table 3-16. 3.3V DC Analog Reference Specifications Symbol BG – – – – – – – – – – – – – – – – – AGND = Vdd/2 AGND = 2 x BandGap AGND = P2[4] (P2[4] = Vdd/2) AGND = BandGap AGND = 1.6 x BandGap AGND Column to Column Variation (AGND = Vdd/2) RefHi = Vdd/2 + BandGap RefHi = 3 x BandGap RefHi = 2 x BandGap + P2[6] (P2[6] = 0.5V) RefHi = P2[4] + BandGap (P2[4] = Vdd/2) RefHi = P2[4] + P2[6] (P2[4] = Vdd/2, P2[6] = 0.5V) RefHi = 3.2 x BandGap RefLo = Vdd/2 - BandGap RefLo = BandGap RefLo = 2 x BandGap - P2[6] (P2[6] = 0.5V) RefLo = P2[4] – BandGap (P2[4] = Vdd/2) RefLo = P2[4]-P2[6] (P2[4] = Vdd/2, P2[6] = 0.5V) Description Bandgap Voltage Reference 1.28 Vdd/2 - 0.03 Not Allowed P2[4] - 0.008 BG - 0.009 1.6 x BG - 0.027 -0.034 Not Allowed Not Allowed Not Allowed Not Allowed P2[4] + P2[6] - 0.075 Not Allowed Not Allowed Not Allowed Not Allowed Not Allowed P2[4] - P2[6] - 0.048 P2[4]- P2[6] + 0.022 P2[4] - P2[6] + 0.092 V P2[4] + P2[6] - 0.009 P2[4] + P2[6] + 0.057 V P2[4] + 0.001 BG + 0.005 1.6 x BG - 0.010 0.000 P2[4] + 0.009 BG + 0.015 1.6 x BG + 0.018 0.034 V V V mV Min 1.30 Vdd/2 - 0.01 Typ 1.33 Vdd/2 + 0.005 Max V V Units October 17, 2006 Document No. 38-12028 Rev. *F 27 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications Table 3-17. 2.7V DC Analog Reference Specifications Symbol BG – – – – – – – – – – – – – – – – – AGND = Vdd/2 AGND = 2 x BandGap AGND = P2[4] (P2[4] = Vdd/2) AGND = BandGap AGND = 1.6 x BandGap AGND Column to Column Variation (AGND = Vdd/2) RefHi = Vdd/2 + BandGap RefHi = 3 x BandGap RefHi = 2 x BandGap + P2[6] (P2[6] = 0.5V) RefHi = P2[4] + BandGap (P2[4] = Vdd/2) RefHi = P2[4] + P2[6] (P2[4] = Vdd/2, P2[6] = 0.5V) RefHi = 3.2 x BandGap RefLo = Vdd/2 - BandGap RefLo = BandGap RefLo = 2 x BandGap - P2[6] (P2[6] = 0.5V) RefLo = P2[4] – BandGap (P2[4] = Vdd/2) RefLo = P2[4]-P2[6] (P2[4] = Vdd/2, P2[6] = 0.5V) Description Bandgap Voltage Reference 1.16 Vdd/2 - 0.03 Not Allowed P2[4] - 0.01 BG - 0.01 Not Allowed -0.034 Not Allowed Not Allowed Not Allowed Not Allowed P2[4] + P2[6] - 0.08 Not Allowed Not Allowed Not Allowed Not Allowed Not Allowed P2[4] - P2[6] - 0.05 P2[4]- P2[6] + 0.01 P2[4] - P2[6] + 0.09 V P2[4] + P2[6] - 0.01 P2[4] + P2[6] + 0.06 V 0.000 0.034 mV P2[4] BG P2[4] + 0.01 BG + 0.015 V V Min 1.30 Vdd/2 - 0.01 Typ 1.33 Vdd/2 + 0.01 Max V V Units 3.3.8 DC Analog PSoC Block Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-18. DC Analog PSoC Block Specifications Symbol RCT CSC Description Resistor Unit Value (Continuous Time) Capacitor Unit Value (Switched Capacitor) – – Min 80 Typ 12.2 – – Max fF Units kΩ Notes October 17, 2006 Document No. 38-12028 Rev. *F 28 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.3.9 DC POR, SMP, and LVD Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Note The bits PORLEV and VM in the table below refer to bits in the VLT_CR register. See the PSoC Mixed-Signal Array Technical Reference Manual for more information on the VLT_CR register. Table 3-19. DC POR and LVD Specifications Symbol VPPOR0 VPPOR1 VPPOR2 VLVD0 VLVD1 VLVD2 VLVD3 VLVD4 VLVD5 VLVD6 VLVD7 VPUMP0 VPUMP1 VPUMP2 VPUMP3 VPUMP4 VPUMP5 VPUMP6 VPUMP7 PORLEV[1:0] = 00b PORLEV[1:0] = 01b PORLEV[1:0] = 10b Vdd Value for LVD Trip VM[2:0] = 000b VM[2:0] = 001b VM[2:0] = 010b VM[2:0] = 011b VM[2:0] = 100b VM[2:0] = 101b VM[2:0] = 110b VM[2:0] = 111b Vdd Value for SMP Trip VM[2:0] = 000b VM[2:0] = 001b VM[2:0] = 010b VM[2:0] = 011b VM[2:0] = 100b VM[2:0] = 101b VM[2:0] = 110b VM[2:0] = 111b 2.500 2.96 3.03 3.18 4.54 4.62 4.71 4.89 2.550 3.02 3.10 3.250 4.64 4.73 4.82 5.00 2.62c 3.09 3.16 3.32d 4.74 4.83 4.92 5.12 V V0 V0 V0 V0 V V V 2.40 2.85 2.95 3.06 4.37 4.50 4.62 4.71 2.450 2.920 3.02 3.13 4.48 4.64 4.73 4.81 2.51a 2.99b 3.09 3.20 4.55 4.75 4.83 4.95 V0 V0 V0 V0 V0 V V V – Description Vdd Value for PPOR Trip 2.36 2.82 4.55 2.40 2.95 4.70 V V V Min Typ Max Units Notes Vdd must be greater than or equal to 2.5V during startup, reset from the XRES pin, or reset from Watchdog. a. b. c. d. Always greater than 50 mV above VPPOR (PORLEV=00) for falling supply. Always greater than 50 mV above VPPOR (PORLEV=01) for falling supply. Always greater than 50 mV above VLVD0. Always greater than 50 mV above VLVD3. October 17, 2006 Document No. 38-12028 Rev. *F 29 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.3.10 DC Programming Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-20. DC Programming Specifications Symbol VddIWRITE IDDP VILP VIHP IILP IIHP VOLV VOHV FlashENPB FlashENT FlashDR Description Supply Voltage for Flash Write Operations Supply Current During Programming or Verify Input Low Voltage During Programming or Verify Input High Voltage During Programming or Verify Input Current when Applying Vilp to P1[0] or P1[1] During Programming or Verify Input Current when Applying Vihp to P1[0] or P1[1] During Programming or Verify Output Low Voltage During Programming or Verify Output High Voltage During Programming or Verify Flash Endurance (per block) Flash Endurance (total) Flash Data Retention a Min 2.70 – – 2.1 – – – Vdd - 1.0 50,000 1,800,000 10 – 5 – – – – – – – – – Typ – 25 0.8 – 0.2 1.5 Max V Units mA V V mA mA V V – – Years Notes Driving internal pull-down resistor. Driving internal pull-down resistor. Vss + 0.75 Vdd – – – Erase/write cycles per block. Erase/write cycles. a. A maximum of 36 x 50,000 block endurance cycles is allowed. This may be balanced between operations on 36x1 blocks of 50,000 maximum cycles each, 36x2 blocks of 25,000 maximum cycles each, or 36x4 blocks of 12,500 maximum cycles each (to limit the total number of cycles to 36x50,000 and that no single block ever sees more than 50,000 cycles). For the full industrial range, the user must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing. Refer to the Flash APIs Application Note AN2015 at http://www.cypress.com under Application Notes for more information. October 17, 2006 Document No. 38-12028 Rev. *F 30 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.4 3.4.1 AC Electrical Characteristics AC Chip-Level Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-21. 5V and 3.3V AC Chip-Level Specifications Symbol FIMO24 Description Internal Main Oscillator Frequency for 24 MHz Min 23.4 24 Typ Max 24.6 a,b,c Units MHz Notes Trimmed for 5V or 3.3V operation using factory trim values. See Figure 3-1b on page 17. SLIMO mode = 0. Trimmed for 5V or 3.3V operation using factory trim values. See Figure 3-1b on page 17. SLIMO mode = 1. FIMO6 Internal Main Oscillator Frequency for 6 MHz 5.75 6 6.35a,b,c MHz FCPU1 FCPU2 F48M F24M F32K1 F32K2 FPLL Jitter24M2 TPLLSLEW TPLLSLEWSLOW CPU Frequency (5V Nominal) CPU Frequency (3.3V Nominal) Digital PSoC Block Frequency Digital PSoC Block Frequency Internal Low Speed Oscillator Frequency External Crystal Oscillator PLL Frequency 24 MHz Period Jitter (PLL) PLL Lock Time PLL Lock Time for Low Gain Setting External Crystal Oscillator Startup to 1% External Crystal Oscillator Startup to 100 ppm 0.93 0.93 0 0 15 – – – 0.5 0.5 – – 24 12 48 24 32 32.768 23.986 – – – 1700 2800 24.6a,b 12.3b,c 49.2 a,b,d MHz MHz MHz MHz kHz kHz MHz ps ms ms ms ms The crystal oscillator frequency is within 100 ppm of its final value by the end of the Tosacc period. Correct operation assumes a properly loaded 1 uW maximum drive level 32.768 kHz crystal. 3.0V ≤ Vdd ≤ 5.5V, -40 oC ≤ TA ≤ 85 oC. Accuracy is capacitor and crystal dependent. 50% duty cycle. Is a multiple (x732) of crystal frequency. Refer to the AC Digital Block Specifications. 24.6b, d 64 – – 600 10 50 2620 3800 TOS TOSACC Jitter32k TXRST DC24M Step24M Fout48M Jitter24M1P Jitter24M1R FMAX TRAMP 32 kHz Period Jitter External Reset Pulse Width 24 MHz Duty Cycle 24 MHz Trim Step Size 48 MHz Output Frequency 24 MHz Period Jitter (IMO) Peak-to-Peak 24 MHz Period Jitter (IMO) Root Mean Squared Maximum frequency of signal on row input or row output. Supply Ramp Time – 10 40 – 46.8 – – – 0 100 – 50 50 48.0 300 – – – 600 12.3 – – 60 – 49.2a,c ns µs % kHz MHz ps ps MHz µs Trimmed. Utilizing factory trim values. a. b. c. d. 4.75V < Vdd < 5.25V. Accuracy derived from Internal Main Oscillator with appropriate trim for Vdd range. 3.0V < Vdd < 3.6V. See Application Note AN2012 “Adjusting PSoC Microcontroller Trims for Dual Voltage-Range Operation” for information on trimming for operation at 3.3V. See the individual user module data sheets for information on maximum frequencies for user modules. October 17, 2006 Document No. 38-12028 Rev. *F 31 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications Table 3-22. 2.7V AC Chip-Level Specifications Symbol FIMO12 Description Internal Main Oscillator Frequency for 12 MHz Min 11.5 12 Typ Max 12.7a,b,c Units MHz Notes Trimmed for 2.7V operation using factory trim values. See Figure 3-1b on page 17. SLIMO mode = 1. Trimmed for 2.7V operation using factory trim values. See Figure 3-1b on page 17. SLIMO mode = 1. Refer to the AC Digital Block Specifications. FIMO6 Internal Main Oscillator Frequency for 6 MHz 5.75 6 6.35a,b,c MHz FCPU1 FBLK27 F32K1 Jitter32k TXRST DC12M Jitter12M1P Jitter12M1R FMAX TRAMP CPU Frequency (2.7V Nominal)0 Digital PSoC Block Frequency (2.7V Nominal) Internal Low Speed Oscillator Frequency 32 kHz Period Jitter External Reset Pulse Width 12 MHz Duty Cycle 12 MHz Period Jitter (IMO) Peak-to-Peak 12 MHz Period Jitter (IMO) Root Mean Squared Maximum frequency of signal on row input or row output. Supply Ramp Time 0.930 0 8 – 10 40 – – – 0 30 12 32 150 – 50 340 – – – 3.15a,b 12.7 96 – 60 600 12.7 – a,b,c MHz0 MHz0 kHz ns µs % ps ps MHz µs a. 2.4V < Vdd < 3.0V. b. Accuracy derived from Internal Main Oscillator with appropriate trim for Vdd range. c. See Application Note AN2012 “Adjusting PSoC Microcontroller Trims for Dual Voltage-Range Operation” for information on maximum frequency for User Modules. PLL Enable TPLLSLEW 24 MHz FPLL PLL Gain 0 Figure 3-3. PLL Lock Timing Diagram PLL Enable TPLLSLEWLOW 24 MHz FPLL PLL Gain 1 Figure 3-4. PLL Lock for Low Gain Setting Timing Diagram October 17, 2006 Document No. 38-12028 Rev. *F 32 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 32K Select TOS 32 kHz F32K2 Figure 3-5. External Crystal Oscillator Startup Timing Diagram Jitter24M1 F 24M Figure 3-6. 24 MHz Period Jitter (IMO) Timing Diagram Jitter32k F 32K2 Figure 3-7. 32 kHz Period Jitter (ECO) Timing Diagram October 17, 2006 Document No. 38-12028 Rev. *F 33 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.4.2 AC General Purpose IO Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-23. 5V and 3.3V AC GPIO Specifications Symbol FGPIO TRiseF TFallF TRiseS TFallS Description GPIO Operating Frequency Rise Time, Normal Strong Mode, Cload = 50 pF Fall Time, Normal Strong Mode, Cload = 50 pF Rise Time, Slow Strong Mode, Cload = 50 pF Fall Time, Slow Strong Mode, Cload = 50 pF 0 3 2 10 10 Min – – – 27 22 Typ 12 18 18 – – Max Units MHz ns ns ns ns Notes Normal Strong Mode Vdd = 4.5 to 5.25V, 10% - 90% Vdd = 4.5 to 5.25V, 10% - 90% Vdd = 3 to 5.25V, 10% - 90% Vdd = 3 to 5.25V, 10% - 90% Table 3-24. 2.7V AC GPIO Specifications Symbol FGPIO TRiseF TFallF TRiseS TFallS Description GPIO Operating Frequency Rise Time, Normal Strong Mode, Cload = 50 pF Fall Time, Normal Strong Mode, Cload = 50 pF Rise Time, Slow Strong Mode, Cload = 50 pF Fall Time, Slow Strong Mode, Cload = 50 pF 0 6 6 18 18 Min – – – 40 40 Typ 3 50 50 120 120 Max Units MHz ns ns ns ns Notes Normal Strong Mode Vdd = 2.4 to 3.0V, 10% - 90% Vdd = 2.4 to 3.0V, 10% - 90% Vdd = 2.4 to 3.0V, 10% - 90% Vdd = 2.4 to 3.0V, 10% - 90% 90% GPIO Pin Output Voltage 10% TRiseF TRiseS TFallF TFallS Figure 3-8. GPIO Timing Diagram October 17, 2006 Document No. 38-12028 Rev. *F 34 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.4.3 AC Operational Amplifier Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Settling times, slew rates, and gain bandwidth are based on the Analog Continuous Time PSoC block. Power = High and Opamp Bias = High is not supported at 3.3V and 2.7V. Table 3-25. 5V AC Operational Amplifier Specifications Symbol TROA Description Rising Settling Time from 80% of ∆V to 0.1% of ∆V (10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High TSOA Falling Settling Time from 20% of ∆V to 0.1% of ∆V (10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High SRROA Rising Slew Rate (20% to 80%)(10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High SRFOA Falling Slew Rate (20% to 80%)(10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High BWOA Gain Bandwidth Product Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High ENOA Noise at 1 kHz (Power = Medium, Opamp Bias = High) 0.75 3.1 5.4 – – – – 100 – – – – MHz MHz MHz nV/rt-Hz 0.01 0.5 4.0 – – – – – – V/µs V/µs V/µs 0.15 1.7 6.5 – – – – – – V/µs V/µs V/µs – – – – – – 5.9 0.92 0.72 µs µs µs – – – – – – 3.9 0.72 0.62 µs µs µs Min Typ Max Units Notes Table 3-26. 3.3V AC Operational Amplifier Specifications Symbol TROA Description Rising Settling Time from 80% of ∆V to 0.1% of ∆V (10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High TSOA Falling Settling Time from 20% of ∆V to 0.1% of ∆V (10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High SRROA Rising Slew Rate (20% to 80%)(10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High SRFOA Falling Slew Rate (20% to 80%)(10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High BWOA Gain Bandwidth Product Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High ENOA Noise at 1 kHz (Power = Medium, Opamp Bias = High) 0.67 2.8 – – – 100 – – – MHz MHz nV/rt-Hz 0.24 1.8 – – – – V/µs V/µs 0.31 2.7 – – – – V/µs V/µs – – – – 5.41 0.72 µs µs – – – – 3.92 0.72 µs µs Min Typ Max Units Notes October 17, 2006 Document No. 38-12028 Rev. *F 35 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications Table 3-27. 2.7V AC Operational Amplifier Specifications Symbol TROA Description Rising Settling Time from 80% of ∆V to 0.1% of ∆V (10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High TSOA Falling Settling Time from 20% of ∆V to 0.1% of ∆V (10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High SRROA Rising Slew Rate (20% to 80%)(10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High SRFOA Falling Slew Rate (20% to 80%)(10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High BWOA Gain Bandwidth Product Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High ENOA Noise at 1 kHz (Power = Medium, Opamp Bias = High) 0.67 2.8 – – – 100 – – – MHz MHz nV/rt-Hz 0.24 1.8 – – – – V/µs V/µs 0.31 2.7 – – – – V/µs V/µs – – – – 5.41 0.72 µs µs – – – – 3.92 0.72 µs µs Min Typ Max Units Notes October 17, 2006 Document No. 38-12028 Rev. *F 36 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications When bypassed by a capacitor on P2[4], the noise of the analog ground signal distributed to each block is reduced by a factor of up to 5 (14 dB). This is at frequencies above the corner frequency defined by the on-chip 8.1k resistance and the external capacitor. dBV/rtHz 10000 0 0.01 0.1 1.0 10 1000 100 0.001 0.01 0.1 Freq (kHz) 1 10 100 Figure 3-9. Typical AGND Noise with P2[4] Bypass At low frequencies, the opamp noise is proportional to 1/f, power independent, and determined by device geometry. At high frequencies, increased power level reduces the noise spectrum level. nV/rtHz 10000 PH_BH PH_BL PM_BL PL_BL 1000 100 10 0.001 0.01 0.1 Freq (kHz) 1 10 100 Figure 3-10. Typical Opamp Noise October 17, 2006 Document No. 38-12028 Rev. *F 37 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.4.4 AC Low Power Comparator Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-28. AC Low Power Comparator Specifications Symbol TRLPC LPC response time Description – Min – Typ 50 Max Units µs Notes ≥ 50 mV overdrive comparator reference set within VREFLPC. 3.4.5 AC Digital Block Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-29. 5V and 3.3V AC Digital Block Specifications Function Timer Capture Pulse Width Maximum Frequency, No Capture Maximum Frequency, With Capture Counter Enable Pulse Width Maximum Frequency, No Enable Input Maximum Frequency, Enable Input Dead Band Kill Pulse Width: Asynchronous Restart Mode Synchronous Restart Mode Disable Mode Maximum Frequency CRCPRS Maximum Input Clock Frequency (PRS Mode) CRCPRS Maximum Input Clock Frequency (CRC Mode) SPIM SPIS Maximum Input Clock Frequency Maximum Input Clock Frequency Width of SS_ Negated Between Transmissions Transmitter Maximum Input Clock Frequency Maximum Input Clock Frequency with Vdd ≥ 4.75V, 2 Stop Bits Receiver Maximum Input Clock Frequency Maximum Input Clock Frequency with Vdd ≥ 4.75V, 2 Stop Bits 20 50 50 – – – – – 50 – – a a a Description Min 50a – – 50a – – – – – – – – Typ – Max Units ns MHz MHz ns MHz MHz Notes 49.2 24.6 – 49.2 24.6 4.75V < Vdd < 5.25V. 4.75V < Vdd < 5.25V. – – – – – – – – – – – – – – 49.2 49.2 24.6 8.2 4.1 – 24.6 49.2 ns ns ns MHz MHz MHz MHz ns ns MHz MHz Maximum data rate at 4.1 MHz due to 2 x over clocking. 4.75V < Vdd < 5.25V. 4.75V < Vdd < 5.25V. clocking. clocking. Maximum data rate at 3.08 MHz due to 8 x over Maximum data rate at 6.15 MHz due to 8 x over Maximum data rate at 3.08 MHz due to 8 x over Maximum data rate at 6.15 MHz due to 8 x over – – – – 24.6 49.2 MHz MHz clocking. clocking. a. 50 ns minimum input pulse width is based on the input synchronizers running at 24 MHz (42 ns nominal period). October 17, 2006 Document No. 38-12028 Rev. *F 38 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications Table 3-30. 2.7V AC Digital Block Specifications Function All Functions Timer Description Maximum Block Clocking Frequency Capture Pulse Width Maximum Frequency, With or Without Capture Counter Enable Pulse Width Maximum Frequency, No Enable Input Maximum Frequency, Enable Input Dead Band Kill Pulse Width: Asynchronous Restart Mode Synchronous Restart Mode Disable Mode0 20 100a 100a – – – – – 100a – – – –0 –0 – – – – – –0 – – – –0 –0 12.7 12.7 12.7 6.35 4.23 –0 12.7 12.7 ns ns ns MHz MHz MHz MHz ns ns MHz MHz Maximum data rate at 3.17 MHz due to 2 x over clocking. 100a – 100 – – a Min Typ Max 12.7 Units MHz ns MHz ns MHz MHz 2.4V < Vdd < 3.0V. Notes –0 – – – – 0 –0 12.7 – 0 12.7 12.7 Maximum Frequency CRCPRS Maximum Input Clock Frequency (PRS Mode) CRCPRS Maximum Input Clock Frequency (CRC Mode) SPIM SPIS Maximum Input Clock Frequency Maximum Input Clock Frequency Width of SS_ Negated Between Transmissions Transmitter Receiver Maximum Input Clock Frequency Maximum Input Clock Frequency clocking. clocking. a. 50 ns minimum input pulse width is based on the input synchronizers running at 12 MHz (84 ns nominal period). Maximum data rate at 1.59 MHz due to 8 x over Maximum data rate at 1.59 MHz due to 8 x over October 17, 2006 Document No. 38-12028 Rev. *F 39 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.4.6 AC Analog Output Buffer Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-31. 5V AC Analog Output Buffer Specifications Symbol TROB Power = Low Power = High TSOB Falling Settling Time to 0.1%, 1V Step, 100pF Load Power = Low Power = High SRROB Rising Slew Rate (20% to 80%), 1V Step, 100pF Load Power = Low Power = High SRFOB Falling Slew Rate (80% to 20%), 1V Step, 100pF Load Power = Low Power = High BWOB Small Signal Bandwidth, 20mVpp, 3dB BW, 100pF Load Power = Low Power = High BWOB Large Signal Bandwidth, 1Vpp, 3dB BW, 100pF Load Power = Low Power = High 300 300 – – – – kHz kHz 0.8 0.8 – – – – MHz MHz 0.65 0.65 – – – – V/µs V/µs 0.65 0.65 – – – – V/µs V/µs – – – – 2.2 2.2 µs µs Description Rising Settling Time to 0.1%, 1V Step, 100pF Load – – – – 2.5 2.5 µs µs Min Typ Max Units Notes Table 3-32. 3.3V AC Analog Output Buffer Specifications Symbol TROB Power = Low Power = High TSOB Falling Settling Time to 0.1%, 1V Step, 100pF Load Power = Low Power = High SRROB Rising Slew Rate (20% to 80%), 1V Step, 100pF Load Power = Low Power = High SRFOB Falling Slew Rate (80% to 20%), 1V Step, 100pF Load Power = Low Power = High BWOB Small Signal Bandwidth, 20mVpp, 3dB BW, 100pF Load Power = Low Power = High BWOB Large Signal Bandwidth, 1Vpp, 3dB BW, 100pF Load Power = Low Power = High 200 200 – – – – kHz kHz 0.7 0.7 – – – – MHz MHz 0.5 0.5 – – – – V/µs V/µs 0.5 0.5 – – – – V/µs V/µs – – – – 2.6 2.6 µs µs Description Rising Settling Time to 0.1%, 1V Step, 100pF Load – – – – 3.8 3.8 µs µs Min Typ Max Units Notes October 17, 2006 Document No. 38-12028 Rev. *F 40 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications Table 3-33. 2.7V AC Analog Output Buffer Specifications Symbol TROB Power = Low Power = High TSOB Falling Settling Time to 0.1%, 1V Step, 100pF Load Power = Low Power = High SRROB Rising Slew Rate (20% to 80%), 1V Step, 100pF Load Power = Low Power = High SRFOB Falling Slew Rate (80% to 20%), 1V Step, 100pF Load Power = Low Power = High BWOB Small Signal Bandwidth, 20mVpp, 3dB BW, 100pF Load Power = Low Power = High BWOB Large Signal Bandwidth, 1Vpp, 3dB BW, 100pF Load Power = Low Power = High 180 180 – – – – kHz kHz 0.6 0.6 – – – – MHz MHz 0.4 0.4 – – – – V/µs V/µs 0.4 0.4 – – – – V/µs V/µs – – – – 3 3 µs µs Description Rising Settling Time to 0.1%, 1V Step, 100pF Load – – – – 4 4 µs µs Min Typ Max Units Notes 3.4.7 AC External Clock Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-34. 5V AC External Clock Specifications Symbol FOSCEXT – – – Frequency High Period Low Period Power Up IMO to Switch Description Min 0.093 20.6 20.6 150 – – – – Typ Max 24.6 5300 – – Units MHz ns ns µs Notes Table 3-35. 3.3V AC External Clock Specifications Symbol FOSCEXT FOSCEXT – – – Description Frequency with CPU Clock divide by 1 a Min 0.093 0.186 41.7 41.7 150 – – – – – Typ Max 12.3 24.6 5300 – – Units MHz MHz ns ns µs Notes Frequency with CPU Clock divide by 2 or greaterb High Period with CPU Clock divide by 1 Low Period with CPU Clock divide by 1 Power Up IMO to Switch a. Maximum CPU frequency is 12 MHz at 3.3V. With the CPU clock divider set to 1, the external clock must adhere to the maximum frequency and duty cycle requirements. b. If the frequency of the external clock is greater than 12 MHz, the CPU clock divider must be set to 2 or greater. In this case, the CPU clock divider will ensure that the fifty percent duty cycle requirement is met. October 17, 2006 Document No. 38-12028 Rev. *F 41 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications Table 3-36. 2.7V AC External Clock Specifications Symbol FOSCEXT FOSCEXT – – – Description Frequency with CPU Clock divide by 1a Frequency with CPU Clock divide by 2 or greaterb High Period with CPU Clock divide by 1 Low Period with CPU Clock divide by 1 Power Up IMO to Switch Min 0.093 0.186 41.7 41.7 150 – – – – – Typ Max 12.3 12.3 5300 – – Units MHz MHz ns ns µs Notes a. Maximum CPU frequency is 12 MHz at 3.3V. With the CPU clock divider set to 1, the external clock must adhere to the maximum frequency and duty cycle requirements. b. If the frequency of the external clock is greater than 12 MHz, the CPU clock divider must be set to 2 or greater. In this case, the CPU clock divider will ensure that the fifty percent duty cycle requirement is met. 3.4.8 AC Programming Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-37. AC Programming Specifications Symbol TRSCLK TFSCLK TSSCLK THSCLK FSCLK TERASEB TWRITE TDSCLK TDSCLK3 TDSCLK2 Rise Time of SCLK Fall Time of SCLK Data Set up Time to Falling Edge of SCLK Data Hold Time from Falling Edge of SCLK Frequency of SCLK Flash Erase Time (Block) Flash Block Write Time Data Out Delay from Falling Edge of SCLK Data Out Delay from Falling Edge of SCLK Data Out Delay from Falling Edge of SCLK Description 1 1 40 40 0 – – – – – Min – – – – – 20 20 – – – Typ 20 20 – – 8 – – 45 50 70 Max Units ns ns ns ns MHz ms ms ns ns ns Vdd > 3.6 3.0 ≤ Vdd ≤ 3.6 2.4 ≤ Vdd ≤ 3.0 Notes October 17, 2006 Document No. 38-12028 Rev. *F 42 [+] [+] Feedback CY8C24x23A Final Data Sheet 3. Electrical Specifications 3.4.9 AC I2C Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only. Table 3-38. AC Characteristics of the I2C SDA and SCL Pins for Vdd > 3.0V Standard Mode Symbol FSCLI2C THDSTAI2C TLOWI2C THIGHI2C TSUSTAI2C THDDATI2C TSUDATI2C TSUSTOI2C TBUFI2C TSPI2C SCL Clock Frequency Hold Time (repeated) START Condition. After this period, the first clock pulse is generated. LOW Period of the SCL Clock HIGH Period of the SCL Clock Set-up Time for a Repeated START Condition Data Hold Time Data Set-up Time Set-up Time for STOP Condition Bus Free Time Between a STOP and START Condition Pulse Width of spikes are suppressed by the input filter. Description 0 4.0 4.7 4.0 4.7 0 250 4.0 4.7 – Min – – – – – – – – – Max 100 0 0.6 1.3 0.6 0.6 0 100 0.6 1.3 0 a Fast Mode Min – – – – – – – – 50 Max 400 Units kHz µs µs µs µs µs ns µs µs ns Notes a. A Fast-Mode I2C-bus device can be used in a Standard-Mode I2C-bus system, but the requirement tSU;DAT ≥ 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line trmax + tSU;DAT = 1000 + 250 = 1250 ns (according to the Standard-Mode I2C-bus specification) before the SCL line is released. Table 3-39. AC Characteristics of the I2C SDA and SCL Pins for Vdd < 3.0V (Fast Mode Not Supported) Standard Mode Symbol FSCLI2C THDSTAI2C TLOWI2C THIGHI2C TSUSTAI2C THDDATI2C TSUDATI2C TSUSTOI2C TBUFI2C TSPI2C SCL Clock Frequency Hold Time (repeated) START Condition. After this period, the first clock pulse is generated. LOW Period of the SCL Clock HIGH Period of the SCL Clock Set-up Time for a Repeated START Condition Data Hold Time Data Set-up Time Set-up Time for STOP Condition Bus Free Time Between a STOP and START Condition Pulse Width of spikes are suppressed by the input filter. Description 0 4.0 4.7 4.0 4.7 0 250 4.0 4.7 – Min – – – – – – – – – Max 100 – – – – – – – – – – Fast Mode Min – – – – – – – – – – Max Units kHz µs µs µs µs µs ns µs µs ns Notes SDA TLOWI2C TSUDATI2C THDSTAI2C TSPI2C TBUFI2C SCL S THDSTAI2C THDDATI2C THIGHI2C TSUSTAI2C TSUSTOI2C Sr P S Figure 3-11. Definition for Timing for Fast/Standard Mode on the I2C Bus October 17, 2006 Document No. 38-12028 Rev. *F 43 [+] [+] Feedback 4. Packaging Information This chapter illustrates the packaging specifications for the CY8C24x23A PSoC device, along with the thermal impedances for each package and the typical package capacitance on crystal pins. Important Note Emulation tools may require a larger area on the target PCB than the chip’s footprint. For a detailed description of the emulation tools’ dimensions, refer to the document titled PSoC Emulator Pod Dimensions at http://www.cypress.com/design/MR10161. 4.1 Packaging Dimensions 51-85075 *A Figure 4-1. 8-Lead (300-Mil) PDIP October 17, 2006 Document No. 38-12028 Rev. *F 44 [+] [+] Feedback CY8C24x23A Final Data Sheet 4. Packaging Information 51-85066 *B 51-85066 *C Figure 4-2. 8-Lead (150-Mil) SOIC ( ) 51-85011-A 51-85011 *A Figure 4-3. 20-Lead (300-Mil) Molded DIP October 17, 2006 Document No. 38-12028 Rev. *F 45 [+] [+] Feedback CY8C24x23A Final Data Sheet 4. Packaging Information 51-85077 *C Figure 4-4. 20-Lead (210-Mil) SSOP 51-85024 *C Figure 4-5. 20-Lead (300-Mil) Molded SOIC October 17, 2006 Document No. 38-12028 Rev. *F 46 [+] [+] Feedback CY8C24x23A Final Data Sheet 4. Packaging Information 51-85014 *D Figure 4-6. 28-Lead (300-Mil) Molded DIP 51-85079 *C Figure 4-7. 28-Lead (210-Mil) SSOP October 17, 2006 Document No. 38-12028 Rev. *F 47 [+] [+] Feedback CY8C24x23A Final Data Sheet 4. Packaging Information 51-85026 *D Figure 4-8. 28-Lead (300-Mil) Molded SOIC X = 138 MIL Y = 138 MIL 32 E-PAD X, Y for this product is 3.53 mm, 3.53 mm (+/-0.11 mm) 51-85188 *A Figure 4-9. 32-Lead (5x5 mm) QFN Important Note For information on the preferred dimensions for mounting QFN packages, see the following Application Note at http://www.amkor.com/products/notes_papers/MLFAppNote.pdf. October 17, 2006 Document No. 38-12028 Rev. *F 48 [+] [+] Feedback CY8C24x23A Final Data Sheet 4. Packaging Information 32 51-85062 *C Figure 4-10. 56-Lead (300-Mil) SSOP 4.2 Thermal Impedances Package 8 PDIP 8 SOIC 20 PDIP 20 SSOP 20 SOIC 28 PDIP 28 SSOP 28 SOIC 32 QFN Typical θJA * 123 oC/W 185 oC/W 109 oC/W 117 oC/W 81 oC/W 69 oC/W 101 oC/W 74 oC/W 22 oC/W Table 4-1. Thermal Impedances per Package * TJ = TA + POWER x θJA October 17, 2006 Document No. 38-12028 Rev. *F 49 [+] [+] Feedback CY8C24x23A Final Data Sheet 4. Packaging Information 4.3 Capacitance on Crystal Pins Package 8 PDIP 8 SOIC 20 PDIP 20 SSOP 20 SOIC 28 PDIP 28 SSOP 28 SOIC 32 QFN Package Capacitance 2.8 pF 2.0 pF 3.0 pF 2.6 pF 2.5 pF 3.5 pF 2.8 pF 2.7 pF 2.0 pF Table 4-2: Typical Package Capacitance on Crystal Pins 4.4 Solder Reflow Peak Temperature Following is the minimum solder reflow peak temperature to achieve good solderability. Table 4-3. Solder Reflow Peak Temperature Package 8 PDIP 8 SOIC 20 PDIP 20 SSOP 20 SOIC 28 PDIP 28 SSOP 28 SOIC 32 QFN Minimum Peak Temperature* 240oC 240oC 240oC 240oC 220oC 240oC 240oC 220oC 240oC Maximum Peak Temperature 260oC 260oC 260oC 260oC 260oC 260oC 260oC 260oC 260oC *Higher temperatures may be required based on the solder melting point. Typical temperatures for solder are 220 ± 5oC with Sn-Pb or 245 ± 5oC with Sn-Ag-Cu paste. Refer to the solder manufacturer specifications. October 17, 2006 Document No. 38-12028 Rev. *F 50 [+] [+] Feedback 5. Development Tool Selection This chapter presents the development tools available for all current PSoC device families including the CY8C24x23A family. 5.1 5.1.1 Software PSoC Designer™ 5.2 Development Kits All development kits can be purchased from the Cypress Online Store. At the core of the PSoC development software suite is PSoC Designer. Utilized by thousands of PSoC developers, this robust software has been facilitating PSoC designs for half a decade. PSoC Designer is available free of charge at http:// www.cypress.com under DESIGN RESOURCES >> Software and Drivers. 5.2.1 CY3215-DK Basic Development Kit 5.1.2 PSoC Express™ The CY3215-DK is for prototyping and development with PSoC Designer. This kit supports in-circuit emulation and the software interface allows users to run, halt, and single step the processor and view the content of specific memory locations. Advance emulation features also supported through PSoC Designer. The kit includes: ■ PSoC Designer Software CD ■ ICE-Cube In-Circuit Emulator ■ ICE Flex-Pod for CY8C29x66 Family ■ Cat-5 Adapter ■ Mini-Eval Programming Board ■ 110 ~ 240V Power Supply, Euro-Plug Adapter ■ iMAGEcraft C Compiler (Registration Required) ■ ISSP Cable ■ USB 2.0 Cable and Blue Cat-5 Cable ■ 2 CY8C29466-24PXI 28-PDIP Chip Samples As the newest addition to the PSoC development software suite, PSoC Express is the first visual embedded system design tool that allows a user to create an entire PSoC project and generate a schematic, BOM, and data sheet without writing a single line of code. Users work directly with application objects such as LEDs, switches, sensors, and fans. PSoC Express is available free of charge at http://www.cypress.com/psocexpress. 5.1.3 PSoC Programmer Flexible enough to be used on the bench in development, yet suitable for factory programming, PSoC Programmer works either as a standalone programming application or it can operate directly from PSoC Designer or PSoC Express. PSoC Programmer software is compatible with both PSoC ICE-Cube InCircuit Emulator and PSoC MiniProg. PSoC programmer is available free ofcharge at http://www.cypress.com/psocprogrammer. 5.1.4 CY3202-C iMAGEcraft C Compiler CY3202 is the optional upgrade to PSoC Designer that enables the iMAGEcraft C compiler. It can be purchased from the Cypress Online Store. At http://www.cypress.com, click the Online Store shopping cart icon at the bottom of the web page, and click PSoC (Programmable System-on-Chip) to view a current list of available items. October 17, 2006 Document No. 38-12028 Rev. *F 51 [+] [+] Feedback CY8C24x23A Final Data Sheet 5. Development Tool Selection 5.2.2 CY3210-ExpressDK PSoC Express Development Kit 5.3.3 CY3214-PSoCEvalUSB The CY3210-ExpressDK is for advanced prototyping and development with PSoC Express (may be used with ICE-Cube In-Circuit Emulator). It provides access to I2C buses, voltage reference, switches, upgradeable modules and more. The kit includes: ■ PSoC Express Software CD ■ Express Development Board ■ 4 Fan Modules ■ 2 Proto Modules ■ MiniProg In-System Serial Programmer ■ MiniEval PCB Evaluation Board ■ Jumper Wire Kit ■ USB 2.0 Cable ■ Serial Cable (DB9) ■ 110 ~ 240V Power Supply, Euro-Plug Adapter ■ 2 CY8C24423A-24PXI 28-PDIP Chip Samples ■ 2 CY8C27443-24PXI 28-PDIP Chip Samples ■ 2 CY8C29466-24PXI 28-PDIP Chip Samples The CY3214-PSoCEvalUSB evaluation kit features a development board for the CY8C24794-24LFXI PSoC device. Special features of the board include both USB and capacitive sensing development and debugging support. This evaluation board also includes an LCD module, potentiometer, LEDs, an enunciator and plenty of bread boarding space to meet all of your evaluation needs. The kit includes: ■ PSoCEvalUSB Board ■ LCD Module ■ MIniProg Programming Unit ■ Mini USB Cable ■ PSoC Designer and Example Projects CD ■ Getting Started Guide ■ Wire Pack 5.4 Device Programmers All device programmers can be purchased from the Cypress Online Store. 5.4.1 CY3216 Modular Programmer 5.3 Evaluation Tools All evaluation tools can be purchased from the Cypress Online Store. The CY3216 Modular Programmer kit features a modular programmer and the MiniProg1 programming unit. The modular programmer includes three programming module cards and supports multiple Cypress products. The kit includes: ■ Modular Programmer Base ■ 3 Programming Module Cards ■ MiniProg Programming Unit ■ PSoC Designer Software CD ■ Getting Started Guide ■ USB 2.0 Cable 5.3.1 CY3210-MiniProg1 The CY3210-MiniProg1 kit allows a user to program PSoC devices via the MiniProg1 programming unit. The MiniProg is a small, compact prototyping programmer that connects to the PC via a provided USB 2.0 cable. The kit includes: ■ MiniProg Programming Unit ■ MiniEval Socket Programming and Evaluation Board ■ 28-Pin CY8C29466-24PXI PDIP PSoC Device Sample ■ 28-Pin CY8C27443-24PXI PDIP PSoC Device Sample ■ PSoC Designer Software CD ■ Getting Started Guide ■ USB 2.0 Cable 5.4.2 CY3207ISSP In-System Serial Programmer (ISSP) 5.3.2 CY3210-PSoCEval1 The CY3207ISSP is a production programmer. It includes protection circuitry and an industrial case that is more robust than the MiniProg in a production-programming environment. Note: CY3207ISSP needs special software and is not compatible with PSoC Programmer. The kit includes: ■ CY3207 Programmer Unit ■ PSoC ISSP Software CD ■ 110 ~ 240V Power Supply, Euro-Plug Adapter ■ USB 2.0 Cable The CY3210-PSoCEval1 kit features an evaluation board and the MiniProg1 programming unit. The evaluation board includes an LCD module, potentiometer, LEDs, and plenty of breadboarding space to meet all of your evaluation needs. The kit includes: ■ Evaluation Board with LCD Module ■ MiniProg Programming Unit ■ 28-Pin CY8C29466-24PXI PDIP PSoC Device Sample (2) ■ PSoC Designer Software CD ■ Getting Started Guide ■ USB 2.0 Cable October 17, 2006 Document No. 38-12028 Rev. *F 52 [+] [+] Feedback CY8C24x23A Final Data Sheet 5. Development Tool Selection 5.5 Accessories (Emulation and Programming) Pin Package All nonQFN Flex-Pod Kita CY325024X23A Foot Kitb CY32508DIP-FK, CY32508SOIC-FK, CY325020DIP-FK, CY325020SOIC-FK, CY325020SSOP-FK, CY325028DIP-FK, CY325028SOIC-FK, CY325028SSOP-FK CY325032QFN-FK Adapterc Table 5-1. Emulation and Programming Accessories Part # All non-QFN Adapters can be found at http:// www.emulation.com. CY8C24423 A-24LFXI 32 QFN CY325024X23AQFN a. Flex-Pod kit includes a practice flex-pod and a practice PCB, in addition to two flex-pods. b. Foot kit includes surface mount feet that can be soldered to the target PCB. c. Programming adapter converts non-DIP package to DIP footprint. Specific details and ordering information for each of the adapters can be found at http://www.emulation.com. 5.6 3rd-Party Tools Several tools have been specially designed by the following 3rd-party vendors to accompany PSoC devices during development and production. Specific details for each of these tools can be found at http://www.cypress.com under DESIGN RESOURCES >> Evaluation Boards. 5.7 Build a PSoC Emulator into Your Board For details on how to emulate your circuit before going to volume production using an on-chip debug (OCD) non-production PSoC device, see Application Note “Debugging - Build a PSoC Emulator into Your Board - AN2323” at http://www.cypress.com/ an2323. October 17, 2006 Document No. 38-12028 Rev. *F 53 [+] [+] Feedback 6. Ordering Information The following table lists the CY8C24x23A PSoC device’s key package features and ordering codes. Table 6-1. CY8C24x23A PSoC Device Key Features and Ordering Information Analog Outputs Analog Blocks Digital IO Pins Analog Inputs Digital Blocks Switch Mode Pump Temperature Range 8 Pin (300 Mil) DIP 8 Pin (150 Mil) SOIC 8 Pin (150 Mil) SOIC (Tape and Reel) 20 Pin (300 Mil) DIP 20 Pin (210 Mil) SSOP 20 Pin (210 Mil) SSOP (Tape and Reel) 20 Pin (300 Mil) SOIC 20 Pin (300 Mil) SOIC (Tape and Reel) 28 Pin (300 Mil) DIP 28 Pin (210 Mil) SSOP 28 Pin (210 Mil) SSOP (Tape and Reel) 28 Pin (300 Mil) SOIC 28 Pin (300 Mil) SOIC (Tape and Reel) 32 Pin (5x5 mm) QFN 56 Pin OCD SSOP CY8C24123A-24PXI CY8C24123A-24SXI CY8C24123A-24SXIT CY8C24223A-24PXI CY8C24223A-24PVXI CY8C24223A-24PVXIT CY8C24223A-24SXI CY8C24223A-24SXIT CY8C24423A-24PXI CY8C24423A-24PVXI CY8C24423A-24PVXIT CY8C24423A-24SXI CY8C24423A-24SXIT CY8C24423A-24LFXI CY8C24000A-24PVXIa 4K 4K 4K 4K 4K 4K 4K 4K 4K 4K 4K 4K 4K 4K 4K 256 256 256 256 256 256 256 256 256 256 256 256 256 256 256 No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 16 16 16 16 16 24 24 24 24 24 24 24 4 4 4 8 8 8 8 8 10 10 10 10 10 10 10 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes a. This part may be used for in-circuit debugging. It is NOT available for production 6.1 Ordering Code Definitions Package Type: Thermal Rating: PX = PDIP Pb-Free C = Commercial SX = SOIC Pb-Free I = Industrial PVX = SSOP Pb-Free E = Extended LFX/LKX = QFN Pb-Free AX = TQFP Pb-Free Speed: 24 MHz Part Number Family Code Technology Code: C = CMOS Marketing Code: 8 = Cypress PSoC Company ID: CY = Cypress CY 8 C 24 xxx-SPxx October 17, 2006 Document No. 38-12028 Rev. *F XRES Pin Ordering Code Package Flash (Bytes) SRAM (Bytes) 54 [+] [+] Feedback 7. Sales and Company Information To obtain information about Cypress Semiconductor or PSoC sales and technical support, reference the following information. Cypress Semiconductor 198 Champion Court San Jose, CA 95134 408.943.2600 Web Sites: Company Information – http://www.cypress.com Sales – http://www.cypress.com/aboutus/sales_locations.cfm Technical Support – http://www.cypress.com/support/login.cfm Revision History Table 7-1. CY8C24x23A Data Sheet Revision History Document Title: CY8C24123A, CY8C24223A, and CY8C24423A PSoC Mixed-Signal Array Final Data Sheet Document Number: 38-12028 Revision ** *A *B *C *D ECN # 236409 247589 261711 279731 352614 Issue Date See ECN See ECN See ECN See ECN See ECN Origin of Change SFV SFV HMT HMT HMT Description of Change New silicon and new document – Preliminary Data Sheet. Changed the title to read “Final” data sheet. Updated Electrical Specifications chapter. Input all SFV memo changes. Updated Electrical Specifications chapter. Update Electrical Specifications chapter, including 2.7 VIL DC GPIO spec. Add Solder Reflow Peak Temperature table. Clean up pinouts and fine tune wording and format throughout. Add new color and CY logo. Add URL to preferred dimensions for mounting MLF packages. Update Transmitter and Receiver AC Digital Block Electrical Specifications. Re-add ISSP pinout identifier. Delete Electrical Specification sentence re: devices running at greater than 12 MHz. Update Solder Reflow Peak Temperature table. Fix CY.com URLs. Update CY copyright. Fix SMP 8-pin SOIC error in Feature and Order table. Update 32-pin QFN E-Pad dimensions and rev. *A. Add ISSP note to pinout tables. Update typical and recommended Storage Temperature per industrial specs. Add OCD non-production pinout and package diagram. Update CY branding and QFN convention. Update package diagram revisions. Add Low Power Comparator (LPC) AC/DC electrical spec. tables. Add new Dev. Tool section. Add CY8C20x34 to PSoC Device Characteristics table. Posting: None *E 424036 See ECN HMT *F 521439 See ECN HMT Distribution: External/Public 7.1 Copyrights and Code Protection © Cypress Semiconductor Corp. 2004-2006. All rights reserved. PSoC Designer™, Programmable System-on-Chip™, and PSoC Express are trademarks and PSoC® is a registered trademark of Cypress Semiconductor Corp. All other trademarks or registered trademarks referenced herein are property of the respective corporations. The information contained herein is subject to change without notice. Cypress Semiconductor assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. Cypress Semiconductor products are not warranted nor intended to be used for medical, life-support, life-saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress Semiconductor. Flash Code Protection Note the following details of the Flash code protection features on Cypress Semiconductor PSoC devices. Cypress Semiconductor products meet the specifications contained in their particular data sheets. Cypress Semiconductor believes that its family of products is one of the most secure families of its kind on the market today, regardless of how they are used. There may be methods, unknown to Cypress Semiconductor, that can breach the code protection features. Any of these methods, to our knowledge, would be dishonest and possibly illegal. Neither Cypress Semiconductor nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Cypress Semiconductor is willing to work with the customer who is concerned about the integrity of their code. Code protection is constantly evolving. We at Cypress Semiconductor are committed to continuously improving the code protection features of our products. October 17, 2006 © Cypress Semiconductor Corp. 2004-2006 — Document No. 38-12028 Rev. *F 55 [+] [+] Feedback