CY8C24X93
PSoC® Programmable System-on-Chip
PSoC® Programmable System-on-Chip
Features
■
Powerful Harvard-architecture processor
❐ M8C CPU with a max speed of 24 MHz
■
Operating Range: 1.71 V to 5.5 V
❐ Standby Mode 1.1 μA (Typ)
❐ Deep Sleep 0.1 μA (Typ)
■
Operating Temperature range: –40 °C to +85 °C
■
Flexible on-chip memory
❐ 8 KB flash, 1 KB SRAM
❐ 16 KB flash, 2 KB SRAM
❐ 32 KB flash, 2 KB SRAM
❐ Read while Write with EEPROM emulation
❐ 50,000 flash erase/write cycles
❐ In-system programming simplifies manufacturing process
■
Four Clock Sources
❐ Internal main oscillator (IMO): 6/12/24 MHz
❐ Internal low-speed oscillator (ILO) at 32 kHz for watchdog
and sleep timers
❐ External 32 KHz Crystal Oscillator
❐ External Clock Input
■
Programmable pin configurations
❐ Up to 36 general purpose dual mode GPIO (Analog inputs
and Digital I/O supported)
❐ High sink current of 25 mA per GPIO
• Max sink current 120 mA for all GPIOs
❐ Source Current
• 5 mA on ports 0 and 1
• 1 mA on ports 2,3 and 4
❐ Configurable internal pull-up, high-Z and open drain modes
❐ Selectable, regulated digital I/O on port 1
❐ Configurable input threshold on port 1
Cypress Semiconductor Corporation
Document Number: 001-86894 Rev. *D
•
■
Versatile Analog functions
❐ Internal Low-Dropout voltage regulator for high power supply
rejection ratio (PSRR)
■
Full-Speed USB
❐ 12 Mbps USB 2.0 compliant
❐ Eight unidirectional endpoints
❐ One bidirectional endpoint
❐ Dedicated 512 byte SRAM
❐ No external crystal required
■
Additional system resources
❐ I2C Slave:
• Selectable to 50 kHz, 100 kHz, or 400 kHz
❐ Configurable up to 12 MHz SPI master and slave
❐ Three 16-bit timers
❐ Watchdog and sleep timers
❐ Integrated supervisory circuit
❐ 10-bit incremental analog-to-digital converter (ADC) with
internal voltage reference
❐ Two general-purpose Comparators
• 3 Voltage References (0.8 V, 1 V, 1.2 V)
• Any pin to either comparator inputs
• Low-power operation at 10 µA
❐ One 8-bit IDAC with full scale range of 512 µA
❐ One 8-bit Software PWM
■
Development Platform
❐ PSoC Designer™ IDE
■
GPIOs and Package options
❐ 13 GPIOs - QFN 16
❐ 28 GPIOs - QFN 32
❐ 34 GPIOs - QFN 48
❐ 36 GPIOs - QFN 48
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised April 27, 2017
CY8C24X93
Logic Block Diagram
Port 4
Port 3
Port 2
Port 1
Port 0
1.8/2.5/3V
LDO
[1]
PWRSYS
(Regulator)
PSoC CORE
SYSTEM BUS
Global Analog Interconnect
1K/2K
SRAM
Supervisory ROM (SROM)
Interrupt
Controller
8K/16K/32K Flash
Nonvolatile Memory
Sleep and
Watchdog
CPU Core (M8C)
6/12/24 MHz Internal Main Oscillator
(IMO)
Internal Low Speed Oscillator (ILO)
Multiple Clock Sources
ANALOG
SYSTEM
Analog
Reference
ADC
Two
Comparators
Analog Mux
IDAC
SYSTEM BUS
USB
I2C
Slave
Internal
Voltage
References
System
Resets
POR
and
LVD
SPI
Master/
Slave
Three 16-Bit
Programmable
Timers
Digital
Clocks
SYSTEM RESOURCES
Note
1. Internal voltage regulator for internal circuitry.
Document Number: 001-86894 Rev. *D
Page 2 of 65
CY8C24X93
More Information
Cypress provides a wealth of data at www.cypress.com to help you to select the right PSoC device for your design, and quickly and
effectively integrate the device into your design. For a comprehensive list of resources, see the knowledge base article “How to Design
with PSoC® 1, PowerPSoC®, and PLC – KBA88292”.
■
Overview: PSoC Portfolio, PSoC Roadmap
■
Product Selectors: PSoC 1, PSoC 3, PSoC 4, or PSoC 5LP.
In addition, PSoC Designer includes a device selection tool.
■
Application Notes and Code Examples: Cover a broad range
of topics, from basic to advanced level. Many of the application
notes include code examples.
■
Technical Reference Manuals (TRM): The TRM provides
complete detailed descriptions of the internal architecture of
the PSoC 1 devices.
■
Development Kits:
❐ CY3215A-DK In-Circuit Emulation Lite Development Kit
includes an in-circuit emulator (ICE). While the ICE-Cube is
primarily used to debug PSoC 1 devices, it can also program
PSoC 1 devices using ISSP.
❐ CY3210-PSOCEVAL1 Kit enables you to evaluate and
experiment
Cypress’s
PSoC
1
programmable
system-on-chip design methodology and architecture.
The MiniProg1 and MiniProg3 device provides an interface for
flash programming.
PSoC Designer
PSoC Designer is a free Windows-based Integrated Design
Environment (IDE). Develop your applications using a library of
pre-characterized analog and digital peripherals in a
drag-and-drop design environment. Then, customize your
design leveraging the dynamically generated API libraries of
code. Figure 1 shows PSoC Designer windows. Note: This is not
the default view.
1. Global Resources – all device hardware settings.
2. Parameters – the parameters of the currently selected User
Modules.
3. Pinout – information related to device pins.
4. Chip-Level Editor – a diagram of the resources available on
the selected chip.
5. Datasheet – the datasheet for the currently selected UM
6. User Modules – all available User Modules for the selected
device.
7. Device Resource Meter – device resource usage for the
current project configuration.
8. Workspace – a tree level diagram of files associated with the
project.
9. Output – output from project build and debug operations.
Note: For detailed information on PSoC Designer, go to PSoC®
Designer > Help > Documentation > Designer Specific
Documents > IDE User Guide.
Figure 1. PSoC Designer Layout
Document Number: 001-86894 Rev. *D
Page 3 of 65
CY8C24X93
Contents
PSoC® Functional Overview ............................................ 6
PSoC Core .................................................................. 6
Analog system ............................................................. 6
Additional System Resources ..................................... 6
Getting Started .................................................................. 7
Silicon Errata ............................................................... 7
Development Kits ........................................................ 7
Training ....................................................................... 7
CYPros Consultants .................................................... 7
Solutions Library .......................................................... 7
Technical Support ....................................................... 7
Development Tools .......................................................... 8
PSoC Designer Software Subsystems ........................ 8
Designing with PSoC Designer ....................................... 9
Select User Modules ................................................... 9
Configure User Modules .............................................. 9
Organize and Connect ................................................ 9
Generate, Verify, and Debug ....................................... 9
Pinouts ............................................................................ 10
16-pin QFN (13 GPIOs) [2] ........................................ 10
32-pin QFN (28 GPIOs) [6] ........................................ 11
32-pin QFN (28 GPIOs) [10] ...................................... 12
48-pin QFN (34 GPIOs) [14] ...................................... 13
48-pin QFN (36 GPIOs (With USB)) [19] ................... 14
48-pin QFN (OCD) (36 GPIOs) [23] .......................... 15
Electrical Specifications
(CY8C24193/493) ............................................................. 16
Absolute Maximum Ratings
(CY8C24193/493) ............................................................. 16
Operating Temperature
(CY8C24193/493) ............................................................. 16
DC Chip-Level Specifications
(CY8C24193/493) ............................................................. 17
DC GPIO Specifications
(CY8C24193/493) ............................................................. 18
DC Analog Mux Bus Specifications
(CY8C24193/493) ............................................................. 21
DC Low Power Comparator Specifications
(CY8C24193/493) ............................................................. 21
Comparator User Module Electrical Specifications
(CY8C24193/493) ............................................................. 21
ADC Electrical Specifications
(CY8C24193/493) ............................................................. 22
DC POR and LVD Specifications
(CY8C24193/493) ............................................................. 23
DC Programming Specifications
(CY8C24193/493) ............................................................. 23
DC I2C Specifications
(CY8C24193/493) ............................................................. 24
Shield Driver DC Specifications
(CY8C24193/493) ............................................................. 24
DC IDAC Specifications
(CY8C24193/493) ............................................................. 24
Document Number: 001-86894 Rev. *D
AC Chip-Level Specifications
(CY8C24193/493) ............................................................. 25
AC General Purpose I/O Specifications
(CY8C24193/493) ............................................................. 26
AC Comparator Specifications
(CY8C24193/493) ............................................................. 26
AC External Clock Specifications
(CY8C24193/493) ............................................................. 26
AC Programming Specifications
(CY8C24193/493) ............................................................. 27
AC I2C Specifications
(CY8C24193/493) ............................................................. 28
Electrical Specifications
(CY8C24093/293/393/693) ............................................... 31
Absolute Maximum Ratings
(CY8C24093/293/393/693) ............................................... 31
Operating Temperature
(CY8C24093/293/393/693) ............................................... 31
DC Chip-Level Specifications
(CY8C24093/293/393/693) ............................................... 32
DC GPIO Specifications
(CY8C24093/293/393/693) ............................................... 33
DC Analog Mux Bus Specifications
(CY8C24093/293/393/693) ............................................... 35
DC Low Power Comparator Specifications
(CY8C24093/293/393/693) ............................................... 35
Comparator User Module Electrical Specifications
(CY8C24093/293/393/693) ............................................... 36
ADC Electrical Specifications
(CY8C24093/293/393/693) ............................................... 36
DC POR and LVD Specifications
(CY8C24093/293/393/693) ............................................... 37
DC Programming Specifications
(CY8C24093/293/393/693) ............................................... 37
DC I2C Specifications
(CY8C24093/293/393/693) ............................................... 38
DC Reference Buffer Specifications
(CY8C24093/293/393/693) ............................................... 38
DC IDAC Specifications
(CY8C24093/293/393/693) ............................................... 38
AC Chip-Level Specifications
(CY8C24093/293/393/693) ............................................... 39
AC GPIO Specifications
(CY8C24093/293/393/693) ............................................... 40
AC Comparator Specifications
(CY8C24093/293/393/693) ............................................... 41
AC External Clock Specifications
(CY8C24093/293/393/693) ............................................... 41
AC Programming Specifications
(CY8C24093/293/393/693) ............................................... 42
AC I2C Specifications
(CY8C24093/293/393/693) ............................................... 43
Page 4 of 65
CY8C24X93
Packaging Information ................................................... 46
Thermal Impedances ................................................. 49
Capacitance on Crystal Pins ..................................... 49
Solder Reflow Specifications ..................................... 49
Development Tool Selection ......................................... 50
Software .................................................................... 50
Development Kits ...................................................... 50
Evaluation Tools ........................................................ 50
Device Programmers ................................................. 50
Ordering Information ...................................................... 51
Ordering Code Definitions ......................................... 51
Acronyms ........................................................................ 52
Document Conventions ................................................. 53
Units of Measure ....................................................... 53
Reference Documents .................................................... 53
Numeric Naming ............................................................. 53
Glossary .......................................................................... 54
Document Number: 001-86894 Rev. *D
Appendix A: Silicon Errata
for the CY8C24093/293/393/693 Family ........................ 55
CY8C24093/293/393/693 Qualification Status .......... 55
CY8C24093/293/393/693 Errata Summary ............... 55
Appendix B: Silicon Errata
for the PSoC® CY8C24193/493 Families ...................... 60
CY8C24193/493 Qualification Status ........................ 60
CY8C24193/493 Errata Summary ............................. 60
Document History Page ................................................. 64
Sales, Solutions, and Legal Information ...................... 65
Worldwide Sales and Design Support ....................... 65
Products .................................................................... 65
PSoC®Solutions ....................................................... 65
Cypress Developer Community ................................. 65
Technical Support ..................................................... 65
Page 5 of 65
CY8C24X93
PSoC® Functional Overview
Comparator
The PSoC family consists of on-chip controller devices, which
are designed to replace multiple traditional microcontroller unit
(MCU)-based components with one, low cost single-chip
programmable component. A PSoC device includes
configurable analog and digital blocks, and programmable
interconnect. This architecture allows the user to create
customized peripheral configurations, to match the requirements
of each individual application. Additionally, a fast CPU, Flash
program memory, SRAM data memory, and configurable I/O are
included in a range of convenient pinouts.
The architecture for this device family, as shown in the Logic
Block Diagram on page 2, consists of three main areas:
The CY8C24x93 family has two high-speed, low-power
comparators. The comparators have three voltage references,
0.8 V, 1.0 V and 1.2 V. Comparator inputs can be connected from
any pin through the analog mux bus. The comparator output can
be read in firmware for processing or routed out via specific pins
(P1_0 or P1_4).
The output of the two comparators can be combined with 2-input
logic functions. The combinatorial output can be optionally
combined with a latched value and routed to a pin output or to
the interrupt controller. The input multiplexers and the
comparator are controller through the CMP User Module.
Analog Multiplexer System
The Analog Mux Bus can connect to every GPIO pin and can be
internally connected to the ADC, Comprators or the IDAC.
■
The Core
■
Analog System
■
System Resources (including a full-speed USB port).
A common, versatile bus allows connection between I/O and the
analog system.
Depending on the PSoC package, up to 36 GPIO are included in
the CY8C24x93 PSoC device. The GPIO provides access to the
MCU and analog mux.
PSoC Core
The PSoC Core is a powerful engine that supports a rich
instruction set. It encompasses SRAM for data storage, an
interrupt controller, sleep and watchdog timers, and IMO and
ILO. The CPU core, called the M8C, is a powerful processor with
speeds up to 24 MHz. The M8C is a 4-MIPS, 8-bit
Harvard-architecture microprocessor.
Other multiplexer applications include:
■
Chip-wide mux that allows analog input from any I/O pin.
■
Crosspoint connection between any I/O pin combinations.
Additional System Resources
System resources provide additional capability, such as
configurable USB and I2C slave, SPI master/slave
communication interface, three 16-bit programmable timers,
software 8-bit PWM, low voltage detect, power on reset, and
various system resets supported by the M8C.
The merits of each system resource are listed here:
■
Analog system
The analog system is composed of an ADC, two comparators
and an IDAC. It has an internal 0.8 V, 1 V or 1.2 V analog
reference. All the pins can be configured to connect to the analog
system.
ADC
The ADC in the CY8C24x93 device is an incremental
analog-to-digital converter with a range of 8 to 10 bits supporting
signed and unsigned data formats. The input to the ADC can be
from any pin.
IDAC
The I2C slave/SPI master-slave module provides
50/100/400 kHz communication over two wires. SPI
communication over three or four wires runs at speeds of
46.9 kHz to 3 MHz (lower for a slower system clock).
■
Low-voltage detection (LVD) interrupts can signal the
application of falling voltage levels, while the advanced
power-on-reset (POR) circuit eliminates the need for a system
supervisor.
■
A register-controlled bypass mode allows the user to disable
the LDO regulator.
■
An 8-bit Software PWM is provided for applications like buzzer
control or lighting control. A 16-bit Timer acts as the input clock
to the PWM. The ISR increments a software counter (8-bit),
checks for PWM compare condition and toggles a GPIO
accordingly. PWM Output is available on all GPIOs.
The IDAC can provide current source up to 512 µA to any GPIO
pin. In the CY8C24x93 family of devices 4 ranges of current
source can be implemented that can vary in 255 steps, and are
connected to analog mux bus.
Table 1. IDAC Ranges
Range
Full Scale Range in µA
1x
64
2x
128
4x
256
8x
512
Document Number: 001-86894 Rev. *D
Page 6 of 65
CY8C24X93
Getting Started
The quickest way to understand PSoC silicon is to read this
datasheet and then use the PSoC Designer Integrated
Development Environment (IDE). This datasheet is an overview
of the PSoC integrated circuit and presents specific pin, register,
and electrical specifications.
Training
Free PSoC technical training (on demand, webinars, and
workshops), which is available online via www.cypress.com,
covers a wide variety of topics and skill levels to assist you in
your designs.
CYPros Consultants
For in depth information, along with detailed programming
details, see the Technical Reference Manual for the PSoC
devices.
Certified PSoC consultants offer everything from technical
assistance to completed PSoC designs. To contact or become a
PSoC consultant go to the CYPros Consultants web site.
For up-to-date ordering, packaging, and electrical specification
information, see the latest PSoC device datasheets on the web
at www.cypress.com/psoc.
Solutions Library
Silicon Errata
Errata documents known issues with silicon including errata
trigger conditions, scope of impact, available workarounds and
silicon revision applicability.
Development Kits
PSoC Development Kits are available online from and through a
growing number of regional and global distributors, which
include Arrow, Avnet, Digi-Key, Farnell, Future Electronics, and
Newark.
Document Number: 001-86894 Rev. *D
Visit our growing library of solution focused designs. Here you
can find various application designs that include firmware and
hardware design files that enable you to complete your designs
quickly.
Technical Support
Technical support – including a searchable Knowledge Base
articles and technical forums – is also available online. If you
cannot find an answer to your question, call our Technical
Support hotline at 1-800-541-4736.
Page 7 of 65
CY8C24X93
Development Tools
PSoC Designer™ is the revolutionary integrated design
environment (IDE) that you can use to customize PSoC to meet
your specific application requirements. PSoC Designer software
accelerates system design and time to market. Develop your
applications using a library of precharacterized analog and digital
peripherals (called user modules) in a drag-and-drop design
environment. Then, customize your design by leveraging the
dynamically generated application programming interface (API)
libraries of code. Finally, debug and test your designs with the
integrated debug environment, including in-circuit emulation and
standard software debug features. PSoC Designer includes:
Code Generation Tools
The code generation tools work seamlessly within the
PSoC Designer interface and have been tested with a full range
of debugging tools. You can develop your design in C, assembly,
or a combination of the two.
Assemblers. The assemblers allow you to merge assembly
code seamlessly with C code. Link libraries automatically use
absolute addressing or are compiled in relative mode, and linked
with other software modules to get absolute addressing.
■
Application editor graphical user interface (GUI) for device and
user module configuration and dynamic reconfiguration
■
Extensive user module catalog
C Language Compilers. C language compilers are available
that support the PSoC family of devices. The products allow you
to create complete C programs for the PSoC family devices. The
optimizing C compilers provide all of the features of C, tailored
to the PSoC architecture. They come complete with embedded
libraries providing port and bus operations, standard keypad and
display support, and extended math functionality.
■
Integrated source-code editor (C and assembly)
Debugger
■
Free C compiler with no size restrictions or time limits
■
Built-in debugger
■
In-circuit emulation
PSoC Designer has a debug environment that provides
hardware in-circuit emulation, allowing you to test the program in
a physical system while providing an internal view of the PSoC
device. Debugger commands allow you to read and program and
read and write data memory, and read and write I/O registers.
You can read and write CPU registers, set and clear breakpoints,
and provide program run, halt, and step control. The debugger
also lets you to create a trace buffer of registers and memory
locations of interest.
Built-in support for communication interfaces:
2
❐ Hardware and software I C slaves and masters
❐ Full-speed USB 2.0
❐ Up
to
four
full-duplex
universal
asynchronous
receiver/transmitters (UARTs), SPI master and slave, and
wireless
PSoC Designer supports the entire library of PSoC 1 devices and
runs on Windows XP, Windows Vista, and Windows 7.
■
PSoC Designer Software Subsystems
Online Help System
The online help system displays online, context-sensitive help.
Designed for procedural and quick reference, each functional
subsystem has its own context-sensitive help. This system also
provides tutorials and links to FAQs and an Online Support
Forum to aid the designer.
Design Entry
In the chip-level view, choose a base device to work with. Then
select different onboard analog and digital components that use
the PSoC blocks, which are called user modules. Examples of
user modules are analog-to-digital converters (ADCs),
digital-to-analog converters (DACs), amplifiers, and filters.
Configure the user modules for your chosen application and
connect them to each other and to the proper pins. Then
generate your project. This prepopulates your project with APIs
and libraries that you can use to program your application.
The tool also supports easy development of multiple
configurations and dynamic reconfiguration. Dynamic
reconfiguration makes it possible to change configurations at run
time. In essence, this lets you to use more than 100 percent of
PSoC’s resources for an application.
Document Number: 001-86894 Rev. *D
In-Circuit Emulator
A low-cost, high-functionality in-circuit emulator (ICE) is
available for development support. This hardware can program
single devices.
The emulator consists of a base unit that connects to the PC
using a USB port. The base unit is universal and operates with
all PSoC devices. Emulation pods for each device family are
available separately. The emulation pod takes the place of the
PSoC device in the target board and performs full-speed
(24 MHz) operation.
Page 8 of 65
CY8C24X93
Designing with PSoC Designer
The development process for the PSoC device differs from that
of a traditional fixed-function microprocessor. The configurable
analog and digital hardware blocks give the PSoC architecture a
unique flexibility that pays dividends in managing specification
change during development and lowering inventory costs. These
configurable resources, called PSoC blocks, have the ability to
implement a wide variety of user-selectable functions. The PSoC
development process is:
10.Select user modules.
11.Configure user modules.
12.Organize and connect.
13.Generate, verify, and debug.
Select User Modules
PSoC Designer provides a library of prebuilt, pretested hardware
peripheral components called “user modules”. User modules
make selecting and implementing peripheral devices, both
analog and digital, simple.
Configure User Modules
Each user module that you select establishes the basic register
settings that implement the selected function. They also provide
parameters and properties that allow you to tailor their precise
configuration to your particular application. For example, a PWM
User Module configures one or more digital PSoC blocks, one
for each eight bits of resolution. Using these parameters, you can
establish the pulse width and duty cycle. Configure the
parameters and properties to correspond to your chosen
application. Enter values directly or by selecting values from
drop-down menus. All of the user modules are documented in
datasheets that may be viewed directly in PSoC Designer or on
the Cypress website. These user module datasheets explain the
Document Number: 001-86894 Rev. *D
internal operation of the user module and provide performance
specifications. Each datasheet describes the use of each user
module parameter, and other information that you may need to
successfully implement your design.
Organize and Connect
Build signal chains at the chip level by interconnecting user
modules to each other and the I/O pins. Perform the selection,
configuration, and routing so that you have complete control over
all on-chip resources.
Generate, Verify, and Debug
When you are ready to test the hardware configuration or move
on to developing code for the project, perform the “Generate
Configuration Files” step. This causes PSoC Designer to
generate source code that automatically configures the device to
your specification and provides the software for the system. The
generated code provides APIs with high-level functions to control
and respond to hardware events at run time, and interrupt
service routines that you can adapt as needed.
A complete code development environment lets you to develop
and customize your applications in C, assembly language, or
both.
The last step in the development process takes place inside
PSoC Designer’s Debugger (accessed by clicking the Connect
icon). PSoC Designer downloads the HEX image to the ICE
where it runs at full-speed. PSoC Designer debugging
capabilities rival those of systems costing many times more. In
addition to traditional single-step, run-to-breakpoint, and
watch-variable features, the debug interface provides a large
trace buffer. It lets you to define complex breakpoint events that
include monitoring address and data bus values, memory
locations, and external signals.
Page 9 of 65
CY8C24X93
Pinouts
16-pin QFN (13 GPIOs) [2]
Table 2. Pin Definitions – CY8C24093 [3]
I/O
I
P2[5] Crystal output (XOut)
2
I/O
I
P2[3] Crystal input (XIn)
3
IOHR
I
P1[7] I2C SCL, SPI SS
2
4
IOHR
I
P1[5] I C SDA, SPI MISO
5
IOHR
I
P1[3] SPI CLK
6
IOHR
I
P1[1] ISSP CLK[4], I2C SCL, SPI
MOSI
7
Power
VSS
IOHR
I
P1[0] ISSP DATA[4], I2C SDA, SPI
CLK[5]
9
IOHR
I
P1[2]
10
IOHR
I
P1[4] Optional external clock
(EXTCLK)
12
13
Input
IOH
P0[1], AI
P0[3], AI
P0[7], AI
VDD
AI , XOut, P2[5]
AI , XIn, P2[3]
AI , I2 C SCL, SPI SS, P1[7]
AI , I2 C SDA, SPI MISO, P1[5]
Ground connection
8
11
Figure 2. CY8C24093 Device
Description
XRES Active high external reset with
internal pull-down
I
P0[4]
Power
VDD
14
IOH
I
P0[7]
15
IOH
I
P0[3]
16
IOH
I
P0[1]
1
2
14
13
1
Name
16
15
Analog
12
11
(Top View)
10
3
9
4
QFN
5
6
7
8
Digital
P0[4] , AI
XRES
P1[4] , EXTCLK, AI
P1[2] , AI
AI, SPI CLK , P1[3]
AI, ISSP CLK, SPI MOSI, P1[1]
VSS
AI, ISSP DATA , I2C SDA, SPI CLK , P1[0]
Type
Pin
No.
Supply voltage
LEGEND A = Analog, I = Input, O = Output, OH = 5 mA High Output Drive, R = Regulated Output.
Notes
2. No center pad.
3. 13 GPIOs.
4. On power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to high impedance state. On reset, after XRES de-asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use
alternate pins if you encounter issues.
5. Alternate SPI clock.
Document Number: 001-86894 Rev. *D
Page 10 of 65
CY8C24X93
32-pin QFN (28 GPIOs) [6]
Table 3. Pin Definitions – CY8C24193 [7]
I
P0[1]
I/O
I
P2[7]
3
I/O
I
P2[5]
Crystal output (XOut)
4
I/O
I
P2[3]
Crystal input (XIn)
5
I/O
I
P2[1]
6
I/O
I
P3[3]
7
I/O
I
P3[1]
8
IOHR
I
P1[7]
I2C SCL, SPI SS
9
IOHR
I
P1[5]
I2C SDA, SPI MISO
10
IOHR
I
P1[3]
SPI CLK.
11
IOHR
I
P1[1]
ISSP CLK[8], I2C SCL, SPI MOSI.
P1[0]
14
IOHR
I
P1[2]
15
IOHR
I
P1[4]
16
IOHR
17
I
Input
ISSP DATA[8], I2C SDA,
SPI CLK[9]
Optional external clock input
(EXTCLK)
P1[6]
XRES
I/O
I
P3[0]
19
I/O
I
P3[2]
20
I/O
I
P2[0]
21
I/O
I
P2[2]
22
I/O
I
P2[4]
23
I/O
I
P2[6]
24
IOH
I
P0[0]
25
IOH
I
P0[2]
26
IOH
I
P0[4]
27
IOH
I
P0[6]
9
30
29
10
11
12
P0[0] , AI
P2[6] , AI
P2[4] , AI
P2[2] , AI
P2[0] , AI
P3[2] , AI
P3[0] , AI
XRES
[8]
18
Active high external reset with
internal pull-down
32
31
Vss
P0 [3], AI
P0 [5], AI
Ground connection.
15
16
I
AI, E XTCLK, P 1[4]
AI, P 1[6]
VSS
IOHR
QFN
(Top View)
24
23
22
21
20
19
18
17
13
14
Power
13
1
2
3
4
5
6
7
8
A I,ISSP CLK , I2C SCL, SPI MOSI, P1[1]
Vss
[8]
AI , ISSP DATA , I2C SDA, SPI CLK, P1[0]
AI, P 1[2]
12
AI , P0[1]
AI , P2[7]
AI, XOut, P2[5]
AI , XIn, P2[3]
AI , P2[1]
AI , P3[3]
AI , P3[1]
AI , I2 C SCL, SPI SS, P1[7]
P0 [4], AI
P0 [2], AI
IOH
2
Figure 3. CY8C24193
Description
26
25
1
Name
P0 [7], AI
Vd d
P0 [6], AI
Analog
28
27
Digital
AI, I2C SDA, SPI MISO, P 1[5]
AI, SPI CLK, P 1[3]
Type
Pin
No.
28
Power
VDD
29
IOH
I
P0[7]
30
IOH
I
P0[5]
31
IOH
I
P0[3]
Supply voltage
32
Power
VSS
Ground connection
CP
Power
VSS
Center pad must be connected to
ground
LEGEND A = Analog, I = Input, O = Output, OH = 5 mA High Output Drive, R = Regulated Output.
Notes
6. 28 GPIOs.
7. The center pad (CP) on the QFN package must be connected to ground (VSS) for best mechanical, thermal, and electrical performance. If not connected to ground,
it must be electrically floated and not connected to any other signal.
8. On power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to high impedance state. On reset, after XRES de-asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use
alternate pins if you encounter issues.
9. Alternate SPI clock.
Document Number: 001-86894 Rev. *D
Page 11 of 65
CY8C24X93
32-pin QFN (28 GPIOs) [10]
Table 4. Pin Definitions – CY8C24293 [11]
P2[5]
Crystal output (XOut)
3
I/O
I
P2[3]
Crystal input (XIn)
4
I/O
I
P2[1]
5
I/O
I
P4[3]
6
I/O
I
P3[3]
7
I/O
I
P3[1]
8
IOHR
I
P1[7]
I2C SCL, SPI SS
9
IOHR
I
P1[5]
I2C SDA, SPI MISO
10
IOHR
I
P1[3]
SPI CLK.
11
IOHR
I
P1[1]
ISSP CLK [12], I2C SCL, SPI MOSI.
12
Power
VSS
Ground connection
13
IOHR
I
P1[0]
ISSP DATA[12], I2C SDA, SPI CLK[13]
14
IOHR
I
P1[2]
15
IOHR
I
P1[4]
16
IOHR
I
P1[6]
17
Input
18
I/O
I
P3[0]
19
I/O
I
P3[2]
20
I/O
I
P4[0]
21
I/O
I
P4[2]
22
I/O
I
P2[0]
23
I/O
I
P2[2]
24
I/O
I
P2[4]
25
IOH
I
P0[0]
26
IOH
I
P0[2]
27
IOH
I
P0[4]
28
IOH
I
P0[6]
29
Power
30
IOH
I
P0[7]
31
IOH
I
P0[3]
32
Power
VSS
Ground connection
CP
Power
VSS
Center pad must be connected to
ground
AI , XOut ,P0[1]
AI , XIn ,P2[5]
AI ,P2[3]
AI ,P2[ 1]
AI ,P4[3]
AI ,P3[3]
AI ,P3[1]
AI ,I2 C SCL, SPI SS,P1[7]
Optional external clock input
(EXTCLK)
Active high external reset with
internal pull-down
P0 [4 ], AI
P0 [2 ], AI
P0 [0 ], AI
P0[1]
I
1
2
3
4
5
6
7
8
QFN
(Top View)
24
23
22
21
20
19
18
17
P2[4] ,AI
P2[2] ,AI
P2[0] ,AI
P4[2] ,AI
P4[0] ,AI
P3[2] ,AI
P3[0] ,AI
XRES
AI, EXTCLK, P 1[ 4]
AI, P 1[ 6]
I
I/O
Vss
P0 [3 ], AI
P0 [7 ], AI
VDD
P0[6], AI
IOH
2
32
31
30
29
28
27
26
25
1
XRES
Figure 4. CY8C24293 Device
Description
9
Name
10
11
12
13
14
15
16
Analog
AI, I2C SDA , SPI MI SO, P 1[ 5]
A I, SP I CLK, P 1[ 3]
AI ,ISSP CLK , I2C SCL, SPI MOSI, P1[1]
Vss
[12]
AI ,ISSP DATA , I2C SDA, SPI CLK, P1[0]
AI, P 1[ 2]
Digital
[12]
Pin
No.
VDD
LEGEND A = Analog, I = Input, O = Output, OH = 5 mA High Output Drive, R = Regulated Output.
Notes
10. 28 GPIOs.
11. The center pad (CP) on the QFN package must be connected to ground (VSS) for best mechanical, thermal, and electrical performance. If not connected to ground,
it must be electrically floated and not connected to any other signal.
12. On power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to high impedance state. On reset, after XRES de-asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use
alternate pins if you encounter issues.
13. Alternate SPI clock.
Document Number: 001-86894 Rev. *D
Page 12 of 65
CY8C24X93
48-pin QFN (34 GPIOs) [14]
Table 5. Pin Definitions – CY8C24393, CY8C24693 [15, 16]
Power
22
IOHR
I
P1[0]
23
24
IOHR
IOHR
I
I
P1[2]
P1[4]
25
26
IOHR
Input
I
P1[6]
XRES
27
28
29
30
31
32
33
34
35
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I
I
I
I
I
I
I
I
AI , XIn ,P2[3]
AI ,P2[1]
AI ,P4[3]
AI ,P4[1]
AI ,P3[7]
AI ,P3[5]
AI ,P3[3]
AI P3[1]
AI ,I2 C SCL, SPI SS,P1[7]
I2C SCL, SPI SS
I2C SDA, SPI MISO
No connection
No connection
SPI CLK
ISSP CLK[17], I2C SCL, SPI MOSI
Ground connection
No connection
No connection
Supply voltage
Optional external clock input
(EXTCLK)
Active high external reset with
internal pull-down
P3[0]
P3[2]
P3[4]
P3[6]
P4[0]
P4[2]
P2[0]
P2[2]
P2[4]
Pin
No.
36
Digital
Analog
5
6
Name
IOH
IOH
I
I
P0[0]
P0[2]
39
40
IOH
IOH
I
I
P0[4]
P0[6]
41
42
43
44
45
46
47
48
CP
Power
IOH
Power
IOH
Power
I
I
P0[2], AI
P0[0], AI
(Top View)
37
38
I
Vd d
P0[6], AI
P0[4], AI
QFN
7
8
9
10
11
12
36
35
34
33
32
31
3
4
NC
IOH
38
37
1
2
42
41
40
39
NC
AI ,P2[7]
AI , XOut,P2[5]
NC ,
P0[7], AI
NC
NC
ISSP DATA[17], I2C SDA, SPI CLK[18]
Crystal output (XOut)
Crystal input (XIn)
46
45
44
43
I
I
No connection
15
16
17
18
19
20
21
22
23
24
IOHR
IOHR
Power
NC
P2[7]
P2[5]
P2[3]
P2[1]
P4[3]
P4[1]
P3[7]
P3[5]
P3[3]
P3[1]
P1[7]
P1[5]
NC
NC
P1[3]
P1[1]
VSS
NC
NC
VDD
P0[1], AI
Vss
P0[3], AI
I
I
I
I
I
I
I
I
I
I
I
I
Figure 5. CY8C24393, CY8C24693 Device
Description
48
47
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
IOHR
IOHR
Name
13
14
Analog
30
29
28
27
26
25
NC
P2[ 4], AI
P2[ 2], AI
P2[ 0], AI
P4[ 2], AI
P4[ 0], AI
P3[ 6], AI
P3[ 4], AI
P3[ 2], AI
P3[0], AI
XRES
P1[ 6], AI
NC
NC
SPI C LK, A I, P1[3]
AI, ISSP C LK, I2C SCL, SPI MOSI, P1[1]
Vss
NC
NC
Vdd
1
AI, ISSP DATA , I2C SDA, SPI CLK, P1[0]
AI, P1 [2 ]
AI, EXTCL K, P1[4]
Digital
I2 C SD A, SPI MIS O, A I, P1[5]
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
VDD
NC
NC
P0[7]
NC
P0[3]
VSS
P0[1]
VSS
Description
No connection
Supply voltage
No connection
No connection
No connection
Ground connection
Center pad must be connected to
ground
LEGENDA = Analog, I = Input, O = Output, NC = No Connection H = 5 mA High Output Drive, R = Regulated Output.
Notes
14. 38 GPIOs.
15. This part is available in limited quantities for In-Circuit Debugging during prototype development. It is not available in production volumes.
16. The center pad (CP) on the QFN package must be connected to ground (VSS) for best mechanical, thermal, and electrical performance. If not connected to ground,
it must be electrically floated and not connected to any other signal.
17. On Power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to High impedance state. On reset, after XRES de- asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. In both cases, a pull-up resistance on these lines combines with the pull-down resistance
(5.6K ohm) and form a potential divider. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use alternate pins if you encounter issues.
18. Alternate SPI clock.
Document Number: 001-86894 Rev. *D
Page 13 of 65
CY8C24X93
48-pin QFN (36 GPIOs (With USB)) [19]
Table 6. Pin Definitions – CY8C24493 [20, 21]
IOHR
I
IOHR
I
Power
I/O
I/O
Power
IOHR
I
NC
P2[7]
P2[5]
P2[3]
P2[1]
P4[3]
P4[1]
P3[7]
P3[5]
P3[3]
P3[1]
P1[7]
P1[5]
NC
NC
P1[3]
P1[1]
VSS
D+
DVDD
P1[0]
23
24
IOHR
IOHR
P1[2]
P1[4]
25
26
IOHR
I
Input
I
I
P1[6]
XRES
27
28
29
I/O
I/O
I/O
I
I
I
P3[0]
P3[2]
P3[4]
30
31
32
33
34
35
36
37
38
39
I/O
I/O
I/O
I/O
I/O
I/O
I/O
IOH
IOH
IOH
I
I
I
I
I
I
I
I
I
I
P3[6]
P4[0]
P4[2]
P2[0]
P2[2]
P2[4]
P2[6]
P0[0]
P0[2]
P0[4]
No connection
Crystal output (XOut)
Crystal input (XIn)
NC
AI , P2[7]
AI , XOut, P2[5]
AI , XIn , P2[3]
AI , P2[1]
AI , P4[3]
AI , P4[1]
AI , P3[7]
AI , P3[5]
AI , P3[3]
AI , P3[1]
AI , I2 C SCL, SPI SS, P1[7]
I2C SCL, SPI SS
I2C SDA, SPI MISO
No connection
No connection
SPI CLK
ISSP CLK[20], I2C SCL, SPI MOSI
Ground connection
USB D+
USB DSupply voltage
ISSP DATA[20], I2C SDA, SPI
CLK[22]
Vss
P0[3], AI
P0[5 ], AI
P0[7], AI
NC
NC
Vdd
P0[6], AI
P0[4], AI
P0[2], AI
P0[0], AI
I
I
I
I
I
I
I
I
I
I
I
I
Figure 6. CY8C24493
Description
P0[1], AI
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
IOHR
IOHR
Name
48
47
46
45
44
43
42
41
40
39
38
37
Analog
1
2
3
4
5
6
7
8
9
10
11
12
QFN
(Top View)
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Digital
36
35
34
33
32
31
30
29
28
27
26
25
P2[6] , AI
P2[4] ,AI
P2[2] ,AI
P2[0] ,AI
P4[2] ,AI
P4[0] ,AI
P3[6] ,AI
P3[4] , AI
P3[2] ,AI
P3[0] , AI
XRES
P1[6] , AI
I2C SDA, SPI MISO, A I, P1[5]
NC
NC
SPI CLK, A I, P1[3]
[20]
AI,ISSP CLK , I2C SCL, SPI MOSI, P1[1]
Vss
D+
DVdd
[20, 22]
AI,ISSP DATA, I2C SDA, SPI CLK, P1[0]
AI, P1[2]
AI, EXTCLK, P1[4]
Pin
No.
Optional external clock input
(EXTCLK)
Active high external reset with
internal pull-down
Pin
No.
40
41
42
43
44
45
46
47
48
CP
Digital
IOH
IOH
IOH
IOH
Analog
I
Power
I
I
I
Power
IOH
I
Power
Name
P0[6]
VDD
NC
NC
P0[7]
P0[5]
P0[3]
VSS
P0[1]
VSS
Description
Supply voltage
No connection
No connection
Ground connection
Center pad must be connected to ground
LEGEND A = Analog, I = Input, O = Output, NC = No Connection H = 5 mA High Output Drive, R = Regulated Output.
Notes
19. 36 GPIOs.
20. On Power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to High impedance state. On reset, after XRES de- asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. In both cases, a pull-up resistance on these lines combines with the pull-down resistance
(5.6K ohm) and form a potential divider. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use alternate pins if you encounter issues.
21. The center pad (CP) on the QFN package must be connected to ground (VSS) for best mechanical, thermal, and electrical performance. If not connected to ground,
it must be electrically floated and not connected to any other signal.
22. Alternate SPI clock.
Document Number: 001-86894 Rev. *D
Page 14 of 65
CY8C24X93
48-pin QFN (OCD) (36 GPIOs) [23]
The 48-pin QFN part is for the CY8C240093 On-Chip Debug (OCD). Note that this part is only used for in-circuit debugging.
Table 7. Pin Definitions – CY8C240093 [24, 25]
18
19
20
21
22
Power
IOHR
I
VSS
D+
DVDD
P1[0]
23
IOHR
I
P1[2]
24
IOHR
I
P1[4]
25
26
IOHR
I
Input
27
28
29
30
31
32
33
34
35
36
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I
I
I
I
I
I
I
I
I
P1[6]
XRES
Crystal output (XOut)
Crystal input (XIn)
OCDO
A E
, P2[7]
I
AI , XOut, P2[5]
AI , XIn , P2[3]
AI , P2[1]
AI , P4[3]
AI , P4[1]
AI , P3[7]
AI , P3[5]
AI , P3[3]
AI , P3[1]
AI , I2 C SCL, SPI SS, P1[7]
I2C SCL, SPI SS
I2C SDA, SPI MISO
OCD CPU clock output
OCD high speed clock output
SPI CLK.
ISSP CLK[27], I2C SCL, SPI
MOSI
Ground connection
USB D+
USB DSupply voltage
ISSP DATA[27], I2C SDA, SPI
CLK[28]
Optional external clock input
(EXTCLK)
Active high external reset with
internal pull-down
P3[0]
P3[2]
P3[4]
P3[6]
P4[0]
P4[2]
P2[0]
P2[2]
P2[4]
P2[6]
OCDO
Vdd
P0[6], AI
P0[4], AI
P0[2], AI
P0[0], AI
I
I
OCD mode direction pin
Vss
P0[3], AI
P0[5 ], AI
P0[7], AI
OCDE
IOHR
IOHR
OCDOE
P2[7]
P2[5]
P2[3]
P2[1]
P4[3]
P4[1]
P3[7]
P3[5]
P3[3]
P3[1]
P1[7]
P1[5]
CCLK
HCLK
P1[3]
P1[1]
P0[1], AI
I
I
I
I
I
I
I
I
I
I
I
I
Figure 7. CY8C240093
Description
48
47
46
45
44
43
42
41
40
39
38
37
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
IOHR
IOHR
Name
1
2
3
4
5
6
7
8
9
10
11
12
QFN
(Top View)
13
14
15
16
17
18
19
20
21
22
23
24
1[26]
2
3
4
5
6
7
8
9
10
11
12
13
14[26]
15[26]
16
17
Digital Analog
36
35
34
33
32
31
30
29
28
27
26
25
P2[6] , AI
P2[4] , AI
P2[2] , AI
P2[0] , AI
P4[2] , AI
P4[0] , AI
P3[6] , AI
P3[4] , AI
P3[2] , AI
P3[0] , AI
XRES
P1[6] , AI
I2C SDA, SPI MISO, AI, P1[5]
CCLK
HCLK
SPI CLK, A I, P1[3]
[27]
AI,ISSP CLK6, I2C SCL, SPI MOSI, P1[1]
Vss
D+
DVdd
[27, 28]
AI,ISSP DATA1 , I2C SDA, SPI CLK, P1[0]
AI, P1[2]
AI, EXTCLK, P1[4]
Pin
No.
Pin
No.
37
Digital
Analog
IOH
I
P0[0]
38
39
IOH
IOH
I
I
P0[2]
P0[4]
40
41
42[26]
43[26]
44
45
46
47
48
CP
IOH
I
P0[6]
VDD
OCDO
OCDE
P0[7]
P0[5]
P0[3]
VSS
P0[1]
VSS
Power
IOH
IOH
IOH
I
I
I
Power
IOH
I
Power
Name
Description
Supply voltage
OCD even data I/O
OCD odd data output
Ground connection
Center pad must be connected to
ground
LEGEND A = Analog, I = Input, O = Output, NC = No Connection H = 5 mA High Output Drive, R = Regulated Output.
Notes
23. 36 GPIOs.
24. This part is available in limited quantities for In-Circuit Debugging during prototype development. It is not available in production volumes.
25. The center pad (CP) on the QFN package must be connected to ground (VSS) for best mechanical, thermal, and electrical performance. If not connected to ground,
it must be electrically floated and not connected to any other signal.
26. This pin (associated with OCD part only) is required for connecting the device to ICE-Cube In-Circuit Emulator for firmware debugging purpose. To know more about
the usage of ICE-Cube, refer to CY3215-DK PSoC® IN-CIRCUIT EMULATOR KIT GUIDE.
27. On Power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to High impedance state. On reset, after XRES de- asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. In both cases, a pull-up resistance on these lines combines with the pull-down resistance
(5.6K ohm) and form a potential divider. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use alternate pins if you encounter issues.
28. Alternate SPI clock.
Document Number: 001-86894 Rev. *D
Page 15 of 65
CY8C24X93
Electrical Specifications (CY8C24193/493)
This section presents the DC and AC electrical specifications of the CY8C24193/493 PSoC devices. For the latest electrical
specifications, confirm that you have the most recent datasheet by visiting the web at http://www.cypress.com/psoc.
Figure 8. Voltage versus CPU Frequency
5.5 V
VDD Voltage
li d ng
Va rati n
e io
Op Reg
1.71 V
750 kHz
3 MHz
CPU
24 MHz
Frequency
Absolute Maximum Ratings (CY8C24193/493)
Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested.
Table 8. Absolute Maximum Ratings
Symbol
Description
Conditions
Min
Typ
Max
Units
TSTG
Storage temperature
Higher storage temperatures reduce data
retention time. Recommended Storage
Temperature is +25 °C ± 25 °C. Extended
duration storage temperatures above 85 °C
degrades reliability.
–55
+25
+125
°C
VDD
Supply voltage relative to VSS
–
–0.5
–
+6.0
V
VIO
DC input voltage
–
VSS – 0.5
–
VDD + 0.5
V
VIOZ
DC voltage applied to tristate
–
VSS – 0.5
–
VDD + 0.5
V
IMIO
Maximum current into any port pin
–
–25
–
+50
mA
ESD
Electro static discharge voltage
Human body model ESD
2000
–
–
V
LU
Latch up current
In accordance with JESD78 standard
–
–
200
mA
Min
Typ
Max
Units
–
+85
°C
70
°C
+100
°C
Operating Temperature (CY8C24193/493)
Table 9. Operating Temperature
Symbol
Description
Conditions
TA
Ambient temperature
–
–40
TC
Commercial temperature range
–
0
TJ
Operational die temperature
The temperature rise from ambient to junction
is package specific. See the Thermal
Impedances on page 49. The user must limit
the power consumption to comply with this
requirement.
Document Number: 001-86894 Rev. *D
–40
–
Page 16 of 65
CY8C24X93
DC Chip-Level Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 10. DC Chip-Level Specifications
Symbol
VDD
[29, 43]
Description
Supply voltage
Conditions
See table DC POR and LVD Specifications
(CY8C24093/293/393/693) on page 37
Min
Typ
Max
Units
1.71
–
5.50
V
IDD24
Supply current, IMO = 24 MHz Conditions are VDD 3.0 V, TA = 25 °C,
CPU = 24 MHz.
–
2.88
4.00
mA
IDD12
Supply current, IMO = 12 MHz Conditions are VDD 3.0 V, TA = 25 °C,
CPU = 12 MHz.
–
1.71
2.60
mA
IDD6
Supply current, IMO = 6 MHz
Conditions are VDD 3.0 V, TA = 25 °C,
CPU = 6 MHz.
–
1.16
1.80
mA
ISB0
Deep sleep current
VDD 3.0 V, TA = 25 °C, I/O regulator turned
off
–
0.10
1.1
A
ISB1
Standby current with POR, LVD VDD 3.0 V, TA = 25 °C, I/O regulator turned
and sleep timer
off
–
1.07
1.50
A
ISBI2C
Standby current with I2C
enabled
–
1.64
–
A
Conditions are VDD = 3.3 V, TA = 25 °C and
CPU = 24 MHz
Notes
29. When VDD remains in the range from 1.71 V to 1.9 V for more than 50 µs, the slew rate when moving from the 1.71 V to 1.9 V range to greater than 2 V must be
slower than 1 V/500 µs to avoid triggering POR. The only other restriction on slew rates for any other voltage range or transition is the SRPOWER_UP parameter.
30. If powering down in standby sleep mode, to properly detect and recover from a VDD brown out condition any of the following actions must be taken:
a. Bring the device out of sleep before powering down.
b. Assure that VDD falls below 100 mV before powering back up.
c. Set the No Buzz bit in the OSC_CR0 register to keep the voltage monitoring circuit powered during sleep.
d. Increase the buzz rate to assure that the falling edge of VDD is captured. The rate is configured through the PSSDC bits in the SLP_CFG register. For the referenced
registers, refer to the Technical Reference Manual. In deep sleep/standby sleep mode, additional low power voltage monitoring circuitry allows VDD brown out
conditions to be detected and resets the device when VDD goes lower than 1.1 V at edge rates slower than 1 V/ms.
Document Number: 001-86894 Rev. *D
Page 17 of 65
CY8C24X93
DC GPIO Specifications (CY8C24193/493)
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 3.0 V to 5.5 V and
–40 °C TA 85 °C, 2.4 V to 3.0 V and –40 °C TA 85 °C, or 1.71 V to 2.4 V and –40 °C TA 85 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 11. 3.0 V to 5.5 V DC GPIO Specifications
Symbol
Description
Conditions
Min
Typ Max Units
RPU
Pull-up resistor
–
4
5.60
8
k
VOH1
High output voltage
Port 2 or 3 pins
IOH < 10 A, maximum of 10 mA source
current in all I/Os
VDD – 0.20
–
–
V
VOH2
High output voltage
Port 2 or 3 Pins
IOH = 1 mA, maximum of 20 mA source
current in all I/Os
VDD – 0.90
–
–
V
VOH3
High output voltage
IOH < 10 A, maximum of 10 mA source
Port 0 or 1 pins with LDO regulator Disabled current in all I/Os
for port 1
VDD – 0.20
–
–
V
VOH4
High output voltage
IOH = 5 mA, maximum of 20 mA source
Port 0 or 1 pins with LDO regulator Disabled current in all I/Os
for port 1
VDD – 0.90
–
–
V
VOH5
IOH < 10 A, VDD > 3.1 V, maximum of
High output voltage
Port 1 Pins with LDO Regulator Enabled for 4 I/Os all sourcing 5 mA
3 V out
2.85
VOH6
High output voltage
IOH = 5 mA, VDD > 3.1 V, maximum of 20 mA
Port 1 pins with LDO regulator enabled for source current in all I/Os
3 V out
2.20
VOH7
High output voltage
IOH < 10 A, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 2.5 V out source current in all I/Os
2.35
VOH8
High output voltage
IOH = 2 mA, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 2.5 V out source current in all I/Os
1.90
VOH9
High output voltage
IOH < 10 A, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 1.8 V out source current in all I/Os
1.60
VOH10
High output voltage
IOH = 1 mA, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 1.8 V out source current in all I/Os
1.20
–
–
V
VOL
Low output voltage
IOL = 25 mA, VDD > 3.3 V, maximum of 60 mA
sink current on even port pins (for example,
P0[2] and P1[4]) and 60 mA sink current on
odd port pins (for example, P0[3] and P1[5])
–
–
0.75
V
VIL
Input low voltage
–
–
–
0.80
V
3.00 3.30
–
–
2.50 2.75
–
–
1.80 2.10
V
V
V
V
V
VIH
Input high voltage
–
2.00
–
–
V
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (Absolute Value)
–
–
0.00
1
1
A
CPIN
Pin capacitance
Package and pin dependent
Temp = 25 °C
0.50
1.70
7
pF
VILLVT3.3 Input Low Voltage with low threshold enable Bit3 of IO_CFG1 set to enable low threshold
set, Enable for Port1
voltage of Port1 input
0.8
V
–
–
VIHLVT3.3 Input High Voltage with low threshold enable Bit3 of IO_CFG1 set to enable low threshold
set, Enable for Port1
voltage of Port1 input
1.4
–
–
V
VILLVT5.5 Input Low Voltage with low threshold enable Bit3 of IO_CFG1 set to enable low threshold
set, Enable for Port1
voltage of Port1 input
0.8
V
–
–
VIHLVT5.5 Input High Voltage with low threshold enable Bit3 of IO_CFG1 set to enable low threshold
set, Enable for Port1
voltage of Port1 input
1.7
–
–
V
Document Number: 001-86894 Rev. *D
Page 18 of 65
CY8C24X93
Table 12. 2.4 V to 3.0 V DC GPIO Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
4
5.60
8
k
IOH < 10 A, maximum of 10 mA source VDD - 0.20
current in all I/Os
–
–
V
High output voltage
Port 2 or 3 Pins
IOH = 0.2 mA, maximum of 10 mA
source current in all I/Os
VDD - 0.40
–
–
V
VOH3
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for port 1
IOH < 10 A, maximum of 10 mA source VDD - 0.20
current in all I/Os
–
–
V
VOH4
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for Port 1
IOH = 2 mA, maximum of 10 mA source VDD - 0.50
current in all I/Os
–
–
V
VOH5A
IOH < 10 A, VDD > 2.4 V, maximum of
High output voltage
Port 1 pins with LDO enabled for 1.8 V 20 mA source current in all I/Os
out
1.50
1.80
2.10
V
VOH6A
High output voltage
IOH = 1 mA, VDD > 2.4 V, maximum of
Port 1 pins with LDO enabled for 1.8 V 20 mA source current in all I/Os
out
1.20
–
–
V
VOL
Low output voltage
IOL = 10 mA, maximum of 30 mA sink
current on even port pins (for example,
P0[2] and P1[4]) and 30 mA sink
current on odd port pins (for example,
P0[3] and P1[5])
–
–
0.75
V
VIL
Input low voltage
–
–
–
0.72
V
VIH
Input high voltage
–
1.40
–
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (absolute value)
–
–
1
1000
nA
CPIN
Capacitive load on pins
Package and pin dependent
Temp = 25 C
0.50
1.70
7
pF
VILLVT2.5
Input Low Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low
threshold voltage of Port1 input
0.7
V
–
VIHLVT2.5 Input High Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low
threshold voltage of Port1 input
1.2
RPU
Pull-up resistor
–
VOH1
High output voltage
Port 2 or 3 pins
VOH2
Document Number: 001-86894 Rev. *D
V
–
V
Page 19 of 65
CY8C24X93
Table 13. 1.71 V to 2.4 V DC GPIO Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
4
5.60
8
k
IOH = 10 A, maximum of 10 mA VDD – 0.20
source current in all I/Os
–
–
V
High output voltage
Port 2 or 3 pins
IOH = 0.5 mA, maximum of 10 mA VDD – 0.50
source current in all I/Os
–
–
V
VOH3
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for Port 1
IOH = 100 A, maximum of 10 mA VDD – 0.20
source current in all I/Os
–
–
V
VOH4
High output voltage
Port 0 or 1 Pins with LDO Regulator
Disabled for Port 1
IOH = 2 mA, maximum of 10 mA source VDD – 0.50
current in all I/Os
–
–
V
VOL
Low output voltage
IOL = 5 mA, maximum of 20 mA sink
current on even port pins (for example,
P0[2] and P1[4]) and 30 mA sink
current on odd port pins (for example,
P0[3] and P1[5])
–
–
0.40
V
VIL
Input low voltage
–
–
–
0.30 × VDD
V
VIH
Input high voltage
–
0.65 × VDD
–
–
V
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (absolute value)
–
–
1
1000
nA
CPIN
Capacitive load on pins
Package and pin dependent
temp = 25 C
0.50
1.70
7
pF
RPU
Pull-up resistor
–
VOH1
High output voltage
Port 2 or 3 pins
VOH2
Table 14. GPIO Current Sink and Source Specifications
Supply
Voltage
Mode
Port 1 per I/O (max)
Port 2/3/4 per
I/O (max)
Total Current Even
Pins (max)
Total Current Odd
Pins (max)
Units
1.71 – 2.4
Sink
5
5
20
30
mA
2.4 – 3.0
3.0 – 5.0
Source
2
0.5
Sink
10
10
Source
2
0.2
Sink
25
25
Source
5
1
10[31]
30
mA
30
mA
60
mA
10[31]
60
20[31]
mA
mA
Note
31. Total current (odd + even ports)
Document Number: 001-86894 Rev. *D
Page 20 of 65
CY8C24X93
DC Analog Mux Bus Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 15. DC Analog Mux Bus Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
RSW
Switch resistance to common analog
bus
–
–
–
800
RGND
Resistance of initialization switch to
VSS
–
–
–
800
The maximum pin voltage for measuring RSW and RGND is 1.8 V
DC Low Power Comparator Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 16. DC Comparator Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
0.2
–
1.8
V
VLPC
Low power comparator (LPC) common Maximum voltage limited to VDD
mode
ILPC
LPC supply current
–
–
10
80
A
VOSLPC
LPC voltage offset
–
–
2.5
30
mV
Comparator User Module Electrical Specifications (CY8C24193/493)
The following table lists the guaranteed maximum and minimum specifications. Unless stated otherwise, the specifications are for the
entire device voltage and temperature operating range: –40 °C TA 85 °C, 1.71 V VDD 5.5 V.
Table 17. Comparator User Module Electrical Specifications
Symbol
Min
Typ
Max
Units
50 mV overdrive
–
70
100
ns
Offset
Valid from 0.2 V to 1.5 V
–
2.5
30
mV
Current
Average DC current, 50 mV
overdrive
–
20
80
µA
Supply voltage > 2 V
Power supply rejection ratio
–
80
–
dB
Supply voltage < 2 V
Power supply rejection ratio
–
40
–
dB
1.5
V
TCOMP
PSRR
Description
Comparator response time
Input range
Document Number: 001-86894 Rev. *D
Conditions
–
0.2
Page 21 of 65
CY8C24X93
ADC Electrical Specifications (CY8C24193/493)
Table 18. ADC User Module Electrical Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
0
–
VREFADC
V
Input
VIN
Input voltage range
–
CIIN
Input capacitance
–
RIN
Input resistance
Equivalent switched cap input
resistance for 8-, 9-, or 10-bit
resolution
ADC reference voltage
FCLK
–
–
5
pF
1/(500fF ×
data clock)
1/(400fF ×
data clock)
1/(300fF ×
data clock)
–
1.14
–
1.26
V
Data clock
Source is chip’s internal main
oscillator. See AC Chip-Level
Specifications on page 25 for
accuracy
2.25
–
6
MHz
S8
8-bit sample rate
Data clock set to 6 MHz.
sample rate = 0.001/
(2^Resolution/Data Clock)
–
23.43
–
ksps
S10
10-bit sample rate
Data clock set to 6 MHz.
sample rate = 0.001/
(2^resolution/data clock)
–
5.85
–
ksps
Reference
VREFADC
Conversion Rate
DC Accuracy
RES
Resolution
Can be set to 8, 9, or 10 bit
8
–
10
bits
DNL
Differential nonlinearity
–
–1
–
+2
LSB
INL
Integral nonlinearity
–
–2
–
+2
LSB
EOFFSET
Offset error
8-bit resolution
0
3.20
19.20
LSB
10-bit resolution
0
12.80
76.80
LSB
EGAIN
Gain error
For any resolution
–5
–
+5
%FSR
IADC
Operating current
–
–
2.10
2.60
mA
PSRR
Power supply rejection ratio
Power
Document Number: 001-86894 Rev. *D
PSRR (VDD > 3.0 V)
–
24
–
dB
PSRR (VDD < 3.0 V)
–
30
–
dB
Page 22 of 65
CY8C24X93
DC POR and LVD Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 19. DC POR and LVD Specifications
Symbol
VPOR0
Description
Conditions
Min
Typ
Max
Units
1.61
–
1.66
1.71
V
2.36
2.41
–
2.60
2.66
–
2.82
2.95
VPOR2
1.66 V selected in PSoC Designer VDD must be greater than or equal to 1.71 V
2.36 V selected in PSoC Designer during startup, reset from the XRES pin, or
reset from watchdog.
2.60 V selected in PSoC Designer
VPOR3
2.82 V selected in PSoC Designer
VLVD0
2.45 V selected in PSoC Designer –
2.40
2.45
2.51
VLVD1
2.71 V selected in PSoC Designer
2.64[46]
2.71
2.78
VLVD2
2.92 V selected in PSoC Designer
2.85[47]
2.92
2.99
VLVD3
3.02 V selected in PSoC Designer
2.95[48]
3.02
3.09
VLVD4
3.13 V selected in PSoC Designer
3.06
3.13
3.20
VLVD5
1.90 V selected in PSoC Designer
1.84
1.90
2.32
VLVD6
1.80 V selected in PSoC Designer
1.75[49]
1.80
1.84
VLVD7
4.73 V selected in PSoC Designer
4.62
4.73
4.83
VPOR1
V
DC Programming Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 20. DC Programming Specifications
Symbol
Description
VDDIWRITE Supply voltage for flash write
operations
IDDP
Supply current during
programming or verify
VILP
Input low voltage during
programming or verify
VIHP
Input high voltage during
programming or verify
IILP
Input current when Applying VILP
to P1[0] or P1[1] during
programming or verify
IIHP
Input current when applying VIHP
to P1[0] or P1[1] during
programming or verify
VOLP
Output low voltage during
programming or verify
VOHP
Output high voltage during
programming or verify
FlashENPB Flash write endurance
FlashDR
Flash data retention
–
Conditions
Min
1.71
Typ
–
Max
5.25
Units
V
–
–
5
25
mA
See appropriate DC GPIO Specifications
(CY8C24093/293/393/693) on page 33
See appropriate DC GPIO Specifications
(CY8C24093/293/393/693) on page 33
Driving internal pull-down resistor
–
–
VIL
V
VIH
–
–
V
–
–
0.2
mA
–
–
1.5
mA
–
–
VSS + 0.75
V
VOH
–
VDD
V
50,000
20
–
–
–
–
–
Years
Driving internal pull-down resistor
See appropriate DC GPIO Specifications
(CY8C24093/293/393/693) on page 33.
For VDD > 3V use VOH4 in Table 36 on
page 33.
Erase/write cycles per block
Following maximum Flash write cycles;
ambient temperature of 55 °C
Notes
32. Always greater than 50 mV above VPPOR1 voltage for falling supply.
33. Always greater than 50 mV above VPPOR2 voltage for falling supply.
34. Always greater than 50 mV above VPPOR3 voltage for falling supply.
35. Always greater than 50 mV above VPPOR0 voltage for falling supply.
Document Number: 001-86894 Rev. *D
Page 23 of 65
CY8C24X93
DC I2C Specifications (CY8C24193/493)
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 3.0 V to 5.5 V and
–40 °C TA 85 °C, 2.4 V to 3.0 V and –40 °C TA 85 °C, or 1.71 V to 2.4 V and –40 °C TA 85 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 21. DC I2C Specifications[36]
Symbol
VILI2C
VIHI2C
Description
Input low level
Input high level
Conditions
3.1 V ≤ VDD ≤ 5.5 V
Min
–
Typ
–
Max
Units
0.25 × VDD
V
2.5 V ≤ VDD ≤ 3.0 V
–
–
0.3 × VDD
V
1.71 V ≤ VDD ≤ 2.4 V
–
–
0.3 × VDD
V
1.71 V ≤ VDD ≤ 5.5 V
0.65 × VDD
–
VDD +
0.7 V[37]
V
Shield Driver DC Specifications (CY8C24193/493)
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 3.0 V to 5.5 V and
–40 °C TA 85 °C, 2.4 V to 3.0 V and –40 °C TA 85 °C, or 1.71 V to 2.4 V and –40 °C TA 85 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 22. Shield Driver DC Specifications
VRef
Reference buffer output
1.7 V ≤ VDD ≤ 5.5 V
0.942
–
1.106
Unit
s
V
VRefHi
Reference buffer output
1.7 V ≤ VDD ≤ 5.5 V
1.104
–
1.296
V
Symbol
Description
Conditions
Min
Typ
Max
DC IDAC Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 23. DC IDAC Specifications (8-bit IDAC)
Symbol
Description
Min
Typ
Max
Units
Notes
IDAC_DNL
Differential nonlinearity
–1
–
1
LSB
IDAC_DNL
Integral nonlinearity
–2
–
2
LSB
IDAC_Current
Range = 4x
138
–
169
µA
DAC setting = 127 dec
Range = 8x
138
–
169
µA
DAC setting = 64 dec
Table 24. DC IDAC Specifications (7-bit IDAC)
Symbol
IDAC_DNL
Description
Differential nonlinearity
Min
Typ
Max
Units
–1
–
1
LSB
Notes
IDAC_DNL
Integral nonlinearity
–2
–
2
LSB
IDAC_Current
Range = 4x
137
–
168
µA
DAC setting = 127 dec
Range = 8x
138
–
169
µA
DAC setting = 64 dec
Notes
36. Pull-up resistors on I2C interface cannot be connected to a supply voltage that is more than 0.7 V higher than the CY8C24x93 power supply. See the CY8C24x93
Silicon Errata document for more details.
37. Please refer to Item # 6 of the CY8C24x93 Family.
Document Number: 001-86894 Rev. *D
Page 24 of 65
CY8C24X93
AC Chip-Level Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 25. AC Chip-Level Specifications
Min
Typ
Max
Units
FIMO24
Symbol
IMO frequency at 24 MHz Setting
Description
–
Conditions
22.8
24
25.2
MHz
FIMO12
IMO frequency at 12 MHz setting
–
11.4
12
12.6
MHz
FIMO6
IMO frequency at 6 MHz setting
–
5.7
6.0
6.3
MHz
FCPU
CPU frequency
–
0.75
–
25.20
MHz
F32K1
ILO frequency
–
15
32
50
kHz
F32K_U
ILO untrimmed frequency
–
13
32
82
kHz
DCIMO
Duty cycle of IMO
–
40
50
60
%
DCILO
ILO duty cycle
–
40
50
60
%
VDD slew rate during power-up
–
–
250
V/ms
After supply voltage is valid
1
–
–
ms
Applies after part has booted
10
–
–
s
SRPOWER_UP Power supply slew rate
tXRST
External reset pulse width at power-up
tXRST2
tJIT_IMO
External reset pulse width after
[39]
power-up[50]
6 MHz IMO cycle-to-cycle jitter (RMS)
–
–
0.7
6.7
ns
6 MHz IMO long term N cycle-to-cycle jitter
(RMS); N = 32
–
–
4.3
29.3
ns
6 MHz IMO period jitter (RMS)
–
–
0.7
3.3
ns
12 MHz IMO cycle-to-cycle jitter (RMS)
–
–
0.5
5.2
ns
12 MHz IMO long term N cycle-to-cycle jitter
(RMS); N = 32
–
–
2.3
5.6
ns
12 MHz IMO period jitter (RMS)
–
–
0.4
2.6
ns
24 MHz IMO cycle-to-cycle jitter (RMS)
–
–
1.0
8.7
ns
24 MHz IMO long term N cycle-to-cycle jitter
(RMS); N = 32
–
–
1.4
6.0
ns
24 MHz IMO period jitter (RMS)
–
–
0.6
4.0
ns
Note
38. The minimum required XRES pulse length is longer when programming the device (see Table 55 on page 42).
39. See the Cypress Jitter Specifications application note, Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 for more information.
Document Number: 001-86894 Rev. *D
Page 25 of 65
CY8C24X93
AC General Purpose I/O Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 26. AC GPIO Specifications
Symbol
FGPIO
Description
GPIO operating frequency
Conditions
Normal strong mode Port 0, 1
Min
0
0
tRISE23
tRISE23L
tRISE01
tRISE01L
tFALL
tFALLL
Rise time, strong mode, Cload = 50 pF
Ports 2 or 3
Rise time, strong mode low supply,
Cload = 50 pF, Ports 2 or 3
Rise time, strong mode, Cload = 50 pF
Ports 0 or 1
Rise time, strong mode low supply,
Cload = 50 pF, Ports 0 or 1
Fall time, strong mode, Cload = 50 pF
all ports
Fall time, strong mode low supply,
Cload = 50 pF, all ports
Typ
Max
Units
– 6 MHz for
MHz
1.71 V 3.1 V, maximum of 4 I/Os
Port 1 Pins with LDO Regulator Enabled all sourcing 5 mA
for 3 V out
2.85
3.00
3.30
V
VOH6
High output voltage
IOH = 5 mA, VDD > 3.1 V, maximum of 20 mA
Port 1 pins with LDO regulator enabled for source current in all I/Os
3 V out
2.20
–
–
V
VOH7
High output voltage
IOH < 10 A, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 2.5 V out source current in all I/Os
2.35
2.50
2.75
V
VOH8
High output voltage
IOH = 2 mA, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 2.5 V out source current in all I/Os
1.90
–
–
V
VOH9
High output voltage
IOH < 10 A, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 1.8 V out source current in all I/Os
1.60
1.80
2.10
V
VOH10
High output voltage
IOH = 1 mA, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 1.8 V out source current in all I/Os
1.20
–
–
V
VOL
Low output voltage
–
–
0.75
V
IOL = 25 mA, VDD > 3.3 V, maximum of
60 mA sink current on even port pins (for
example, P0[2] and P1[4]) and 60 mA sink
current on odd port pins (for example, P0[3]
and P1[5])
VIL
Input low voltage
–
–
–
0.80
V
VIH
Input high voltage
–
2.00
–
–
V
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (Absolute Value)
–
–
0.001
1
A
CPIN
Pin capacitance
Package and pin dependent
Temp = 25 °C
0.50
1.70
7
pF
VILLVT3.3
Input Low Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
0.8
V
–
–
VIHLVT3.3
Input High Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
1.4
–
–
V
VILLVT5.5
Input Low Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
0.8
V
–
–
VIHLVT5.5
Input High Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
1.7
–
–
V
Document Number: 001-86894 Rev. *D
Page 33 of 65
CY8C24X93
Table 37. 2.4 V to 3.0 V DC GPIO Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
4
5.60
8
k
IOH < 10 A, maximum of 10 mA source
current in all I/Os
VDD – 0.20
–
–
V
High output voltage
Port 2 or 3 or 4 pins
IOH = 0.2 mA, maximum of 10 mA source
current in all I/Os
VDD – 0.40
–
–
V
VOH3
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for port 1
IOH < 10 A, maximum of 10 mA source
current in all I/Os
VDD – 0.20
–
–
V
VOH4
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for Port 1
IOH = 2 mA, maximum of 10 mA source
current in all I/Os
VDD – 0.50
–
–
V
VOH5A
High output voltage
IOH < 10 A, VDD > 2.4 V, maximum of
Port 1 pins with LDO enabled for 1.8 V out 20 mA source current in all I/Os
1.50
1.80
2.10
V
VOH6A
High output voltage
IOH = 1 mA, VDD > 2.4 V, maximum of 20 mA
Port 1 pins with LDO enabled for 1.8 V out source current in all I/Os
1.20
–
–
V
VOL
Low output voltage
–
–
0.75
V
VIL
Input low voltage
–
–
–
0.72
VIH
Input high voltage
–
1.40
–
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (absolute value)
–
–
1
1000
nA
CPIN
Capacitive load on pins
Package and pin dependent
Temp = 25 C
0.50
1.70
7
pF
VILLVT2.5
Input Low Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
0.7
V
–
VIHLVT2.5
Input High Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
1.2
RPU
Pull-up resistor
–
VOH1
High output voltage
Port 2 or 3 or 4 pins
VOH2
IOL = 10 mA, maximum of 30 mA sink
current on even port pins (for example,
P0[2] and P1[4]) and 30 mA sink current on
odd port pins (for example, P0[3] and P1[5])
V
V
–
V
Table 38. 1.71 V to 2.4 V DC GPIO Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
4
RPU
Pull-up resistor
–
5.60
8
k
VOH1
High output voltage
Port 2 or 3 or 4 pins
IOH = 10 A, maximum of 10 mA VDD – 0.20
source current in all I/Os
–
–
V
VOH2
High output voltage
Port 2 or 3 or 4 pins
IOH = 0.5 mA, maximum of 10 mA VDD – 0.50
source current in all I/Os
–
–
V
VOH3
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for Port 1
IOH = 100 A, maximum of 10 mA VDD – 0.20
source current in all I/Os
–
–
V
VOH4
High output voltage
Port 0 or 1 Pins with LDO Regulator
Disabled for Port 1
IOH = 2 mA, maximum of 10 mA source VDD – 0.50
current in all I/Os
–
–
V
VOL
Low output voltage
IOL = 5 mA, maximum of 20 mA sink
current on even port pins (for example,
P0[2] and P1[4]) and 30 mA sink
current on odd port pins (for example,
P0[3] and P1[5])
–
0.40
V
Document Number: 001-86894 Rev. *D
–
Page 34 of 65
CY8C24X93
Table 38. 1.71 V to 2.4 V DC GPIO Specifications (continued)
Symbol
Description
Conditions
Min
Typ
Max
Units
VIL
Input low voltage
–
–
–
0.30 × VDD
V
VIH
Input high voltage
–
0.65 × VDD
–
–
V
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (absolute value)
–
–
1
1000
nA
CPIN
Capacitive load on pins
Package and pin dependent
temp = 25 °C
0.50
1.70
7
pF
Min
Typ
Max
Units
Table 39. DC Characteristics – USB Interface
Symbol
Description
Conditions
RUSBI
USB D+ pull-up resistance
With idle bus
900
–
1575
RUSBA
USB D+ pull-up resistance
While receiving traffic
1425
–
3090
VOHUSB
Static output high
–
2.8
–
3.6
V
VOLUSB
Static output low
–
–
–
0.3
V
VDI
Differential input sensitivity
–
0.2
–
VCM
Differential input common mode range
–
0.8
–
2.5
V
VSE
Single ended receiver threshold
–
0.8
–
2.0
V
CIN
Transceiver capacitance
–
–
–
50
pF
V
IIO
High Z state data line leakage
On D+ or D- line
–10
–
+10
A
RPS2
PS/2 pull-up resistance
–
3000
5000
7000
REXT
External USB series resistor
In series with each USB pin
21.78
22.0
22.22
DC Analog Mux Bus Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 40. DC Analog Mux Bus Specifications
Symbol
RSW
Description
Conditions
Switch resistance to common analog bus –
RGND
Resistance of initialization switch to VSS
The maximum pin voltage for measuring RSW and RGND is 1.8 V
–
Min
Typ
Max
Units
–
–
800
–
–
800
DC Low Power Comparator Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 41. DC Comparator Specifications
Conditions
Min
Typ
Max
Units
VLPC
Symbol
Low power comparator (LPC) common
mode
Description
Maximum voltage limited to VDD
0.0
–
1.8
V
ILPC
LPC supply current
–
–
10
40
A
VOSLPC
LPC voltage offset
–
–
3
30
mV
Document Number: 001-86894 Rev. *D
Page 35 of 65
CY8C24X93
Comparator User Module Electrical Specifications (CY8C24093/293/393/693)
The following table lists the guaranteed maximum and minimum specifications. Unless stated otherwise, the specifications are for the
entire device voltage and temperature operating range: –40 °C TA 85 °C, 1.71 V VDD 5.5 V.
Table 42. Comparator User Module Electrical Specifications
Symbol
Min
Typ
Max
Units
50 mV overdrive
–
70
100
ns
Offset
Valid from 0.2 V to VDD – 0.2 V
–
2.5
30
mV
Current
Average DC current, 50 mV
overdrive
–
20
80
µA
Supply voltage > 2 V
Power supply rejection ratio
–
80
–
dB
Supply voltage < 2 V
Power supply rejection ratio
–
40
–
dB
–
0
1.5
V
tCOMP
PSRR
Description
Comparator response time
Input range
Conditions
ADC Electrical Specifications (CY8C24093/293/393/693)
Table 43. ADC User Module Electrical Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
0
–
VREFADC
V
–
–
5
pF
Input
VIN
Input voltage range
CIIN
Input capacitance
–
RIN
Input resistance
Equivalent switched cap input
resistance for 8-, 9-, or 10-bit
resolution
ADC reference voltage
–
1.14
–
1.26
V
2.25
–
6
MHz
–
1/(500fF × 1/(400fF × 1/(300fF ×
data clock) data clock) data clock)
Reference
VREFADC
Conversion Rate
FCLK
Data clock
Source is chip’s internal main
oscillator. See AC Chip-Level
Specifications for accuracy
S8
8-bit sample rate
Data clock set to 6 MHz. sample
rate = 0.001/ (2^Resolution/Data
Clock)
–
23.43
–
ksps
S10
10-bit sample rate
Data clock set to 6 MHz. sample
rate = 0.001/ (2^resolution/data
clock)
–
5.85
–
ksps
RES
Resolution
Can be set to 8-, 9-, or 10-bit
8
–
10
bits
DC Accuracy
DNL
Differential nonlinearity
–
–1
–
+2
LSB
INL
Integral nonlinearity
–
–2
–
+2
LSB
EOFFSET
Offset error
8-bit resolution
0
3.20
19.20
LSB
10-bit resolution
0
12.80
76.80
LSB
Gain error
For any resolution
–5
–
+5
%FSR
IADC
Operating current
–
–
2.10
2.60
mA
PSRR
Power supply rejection ratio
PSRR (VDD > 3.0 V)
–
24
–
dB
PSRR (VDD < 3.0 V)
–
30
–
dB
EGAIN
Power
Document Number: 001-86894 Rev. *D
Page 36 of 65
CY8C24X93
DC POR and LVD Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 44. DC POR and LVD Specifications
Symbol
Description
Conditions
Min
VPOR0
1.66 V selected in PSoC Designer
2.36 V selected in PSoC Designer
–
VPOR2
2.60 V selected in PSoC Designer
VDD must be greater than or equal
to 1.71 V during startup, reset
from the XRES pin, or reset from
watchdog.
1.61
VPOR1
–
2.60
2.66
VPOR3
2.82 V selected in PSoC Designer
–
2.82
2.95
VLVD0
2.45 V selected in PSoC Designer
2.40
2.45
2.51
VLVD1
2.71 V selected in PSoC Designer
2.64[46]
2.71
2.78
VLVD2
2.92 V selected in PSoC Designer
2.85[47]
2.92
2.99
VLVD3
3.02 V selected in PSoC Designer
2.95[48]
3.02
3.09
VLVD4
3.13 V selected in PSoC Designer
3.06
3.13
3.20
VLVD5
1.90 V selected in PSoC Designer
1.84
1.90
2.32
VLVD6
1.80 V selected in PSoC Designer
1.75[49]
1.80
1.84
VLVD7
4.73 V selected in PSoC Designer
4.62
4.73
4.83
–
Typ
Max
Units
1.66
1.71
V
2.36
2.41
V
DC Programming Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 45. DC Programming Specifications
Symbol
VDDIWRITE
IDDP
VILP
VIHP
IILP
IIHP
VOLP
VOHP
FlashENPB
FlashDR
Description
Supply voltage for flash write
operations
Supply current during
programming or verify
Input low voltage during
programming or verify
–
Conditions
Min
1.71
Typ
–
Max
5.25
Units
V
–
–
5
25
mA
–
–
VIL
V
VIH
–
–
V
–
–
0.2
mA
–
–
1.5
mA
–
–
VSS + 0.75
V
VOH
–
VDD
V
50,000
20
–
–
–
–
–
Years
See
the
appropriate
DC
GPIO
Specifications (CY8C24093/293/393/693)
on page 33
Input high voltage during
See
the
appropriate
DC
GPIO
programming or verify
Specifications (CY8C24093/293/393/693)
on page 33
Input current when Applying VILP Driving internal pull-down resistor
to P1[0] or P1[1] during
programming or verify
Input current when applying VIHP Driving internal pull-down resistor
to P1[0] or P1[1] during
programming or verify
Output low voltage during
programming or verify
Output high voltage during
See appropriate DC GPIO Specifications
programming or verify
(CY8C24093/293/393/693) on page 33. For
VDD > 3 V use VOH4 in Table 34 on page 31.
Flash write endurance
Erase/write cycles per block
Flash data retention
Following maximum Flash write cycles;
ambient temperature of 55 °C
Notes
46. Always greater than 50 mV above VPPOR1 voltage for falling supply.
47. Always greater than 50 mV above VPPOR2 voltage for falling supply.
48. Always greater than 50 mV above VPPOR3 voltage for falling supply.
49. Always greater than 50 mV above VPPOR0 voltage for falling supply.
Document Number: 001-86894 Rev. *D
Page 37 of 65
CY8C24X93
DC I2C Specifications (CY8C24093/293/393/693)
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 3.0 V to 5.5 V and
–40 °C TA 85 °C, 2.4 V to 3.0 V and –40 °C TA 85 °C, or 1.71 V to 2.4 V and –40 °C TA 85 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 46. DC I2C Specifications
Symbol
VILI2C
VIHI2C
Description
Input low level
Input high level
Conditions
3.1 V ≤ VDD ≤ 5.5 V
Min
–
Typ
–
Max
Units
0.25 × VDD
V
2.5 V ≤ VDD ≤ 3.0 V
–
–
0.3 × VDD
V
1.71 V ≤ VDD ≤ 2.4 V
–
–
0.3 × VDD
V
1.71 V ≤ VDD ≤ 5.5 V
0.65 × VDD
–
–
V
DC Reference Buffer Specifications (CY8C24093/293/393/693)
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 3.0 V to 5.5 V and
–40 °C TA 85 °C, 2.4 V to 3.0 V and –40 °C TA 85 °C, or 1.71 V to 2.4 V and –40 °C TA 85 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 47. DC Reference Buffer Specifications
Symbol
VRef
Description
Reference buffer output
Conditions
1.7 V ≤ VDD ≤ 5.5 V
Min
1
Typ
–
Max
1.05
Units
V
VRefHi
Reference buffer output
1.7 V ≤ VDD ≤ 5.5 V
1.2
–
1.25
V
DC IDAC Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 48. DC IDAC Specifications
Symbol
IDAC_DNL
IDAC_INL
IDAC_Gain
(Source)
Description
Differential nonlinearity
Integral nonlinearity
Range = 0.5x
Range = 1x
Range = 2x
Range = 4x
Range = 8x
Document Number: 001-86894 Rev. *D
Min
–4.5
–5
6.64
14.5
42.7
91.1
184.5
Typ
–
–
–
–
–
–
–
Max
+4.5
+5
22.46
47.8
92.3
170
426.9
Units
Notes
LSB
LSB
µA DAC setting = 128 dec
µA
µA
µA DAC setting = 128 dec
µA DAC setting = 128 dec
Page 38 of 65
CY8C24X93
AC Chip-Level Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 49. AC Chip-Level Specifications
Min
Typ
Max
Units
FIMO24
Symbol
IMO frequency at 24 MHz Setting
–
22.8
24
25.2
MHz
FIMO12
IMO frequency at 12 MHz setting
–
11.4
12
12.6
MHz
FIMO6
IMO frequency at 6 MHz setting
–
5.7
6.0
6.3
MHz
FCPU
CPU frequency
–
0.75
–
25.20
MHz
F32K1
ILO frequency
–
15
32
50
kHz
F32K_U
ILO untrimmed frequency
–
13
32
82
kHz
DCIMO
Duty cycle of IMO
–
40
50
60
%
DCILO
ILO duty cycle
–
40
50
60
%
SRPOWER_UP
Power supply slew rate
VDD slew rate during power-up
–
–
250
V/ms
tXRST
External reset pulse width at power-up After supply voltage is valid
1
–
–
ms
tXRST2
External reset pulse width after
power-up[50]
Applies after part has booted
10
–
–
s
Startup time of ECO
–
–
1
–
s
N=32
6 MHz IMO cycle-to-cycle jitter (RMS)
–
0.7
6.7
ns
6 MHz IMO long term N (N = 32)
cycle-to-cycle jitter (RMS)
–
4.3
29.3
ns
6 MHz IMO period jitter (RMS)
–
0.7
3.3
ns
12 MHz IMO cycle-to-cycle jitter (RMS)
–
0.5
5.2
ns
12 MHz IMO long term N (N = 32)
cycle-to-cycle jitter (RMS)
–
2.3
5.6
ns
tOS
tJIT_IMO
[51]
Description
Conditions
12 MHz IMO period jitter (RMS)
–
0.4
2.6
ns
24 MHz IMO cycle-to-cycle jitter (RMS)
–
1.0
8.7
ns
24 MHz IMO long term N (N = 32)
cycle-to-cycle jitter (RMS)
–
1.4
6.0
ns
24 MHz IMO period jitter (RMS)
–
0.6
4.0
ns
Notes
50. The minimum required XRES pulse length is longer when programming the device (see Table 55 on page 42).
51. Refer to Cypress Jitter Specifications application note, Understanding Datasheet Jitter Specifications for Cypress Timing Products for more information.
Document Number: 001-86894 Rev. *D
Page 39 of 65
CY8C24X93
AC GPIO Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 50. AC GPIO Specifications
Symbol
FGPIO
tRISE23
tRISE23L
tRISE01
tRISE01L
tFALL
tFALLL
Description
GPIO operating frequency
Conditions
Normal strong mode Port 0, 1
Rise time, strong mode, Cload = 50 pF
Port 2 or 3 or 4 pins
Rise time, strong mode low supply,
Cload = 50 pF, Port 2 or 3 or 4 pins
Rise time, strong mode, Cload = 50 pF
Ports 0 or 1
Rise time, strong mode low supply,
Cload = 50 pF, Ports 0 or 1
Fall time, strong mode, Cload = 50 pF
all ports
Fall time, strong mode low supply,
Cload = 50 pF, all ports
Min
0
Typ
–
Max
Units
6 MHz for
MHz
1.71 V
工商网监
湘ICP备2023018690号
