THIS SPEC IS OBSOLETE
Spec No: 001-98941
Spec Title: S6E2H4 SERIES 32-BIT ARM(R) CORTEX(R)M4F, FM4 MICROCONTROLLER
Replaced by: NONE
S6E2H4 Series
32-bit ARM® Cortex®-M4F
FM4 Microcontroller
Devices in the S6E2H4 Series are highly integrated 32-bit microcontrollers with high performance and competitive cost. These
series is based on the ARM Cortex-M4F Processor with on-chip Flash memory and SRAM. The series has peripheral functions
such as Motor Control Timers, ADCs and Communication Interfaces (CAN, UART, CSIO, I2C, LIN).
Features
SRAM0:
Up to 32 Kbytes
Up to 16 Kbytes
SRAM2: Up to 16 Kbytes
SRAM1:
32-bit ARM Cortex-M4F Core
Processor version: r0p1
Up to 160 MHz Frequency Operation
External Bus Interface
FPU built-in
Supports SRAM, NOR, NAND Flash and SDRAM device
Support DSP instruction
Up to 9 chip selects CS0 to CS8 (CS8 is only for SDRAM)
Memory Protection Unit (MPU): improves the reliability of an
8-/16-bit Data width
embedded system
Integrated Nested Vectored Interrupt Controller (NVIC): 1
NMI (non-maskable interrupt) and 128 peripheral interrupts
and 16 priority levels
24-bit System timer (Sys Tick): System timer for OS task
Up to 25-bit Address bit
Supports Address/Data multiplex
Supports external RDY function
Supports scramble function
management
• Possible to set the validity/invalidity of the scramble
function for the external areas 0x6000_0000 to
0xDFFF_FFFF in 4 Mbytes units.
• Possible to set two kinds of the scramble key
• Note: It is necessary to prepare the dedicated software
library to use the scramble function.
On-chip Memories
Flash memory
These series are based on two independent on-chip Flash
memories.
MainFlash memory
• Up to 512 Kbytes
• Built-in Flash Accelerator System with 16 Kbytes trace
buffer memory
• The read access to Flash memory can be achieved
without wait-cycle up to operation frequency of 72 MHz.
Even at the operation frequency more than 72 MHz, an
equivalent access to Flash memory can be obtained by
Flash Accelerator System.
• Security function for code protection
WorkFlash memory
• 32 Kbytes
• Read cycle:
• 6 wait-cycle: the operation frequency more than 120
MHz, and up to 160 MHz
• 4 wait-cycle: the operation frequency more than 72 MHz,
and up to 120 MHz
• 2 wait-cycle: the operation frequency more than 40 MHz,
and up to 72 MHz
• 0 wait-cycle: the operation frequency up to 40 MHz
• Security function is shared with code protection
CAN Interface (Max 2 channels)
Compatible with CAN Specification 2.0A/B
Maximum transfer rate: 1 Mbps
Built-in 32 message buffer
Multi-function Serial Interface (Max 8 channels)
64 bytes with FIFO (the FIFO step numbers are variable
depending on the settings of the communication mode or bit
length.)
Operation mode is selectable from the followings for each
channel.
UART
CSIO
LIN
I2 C
UART
SRAM
This is composed of three independent SRAMs (SRAM0,
SRAM1 and SRAM2). SRAM0 is connected to I-code bus or
D-code bus of Cortex-M4F core. SRAM1 and SRAM2 are
connected to System bus of Cortex-M4F core.
Cypress Semiconductor Corporation
Document Number: 001-98941 Rev.*C
•
198 Champion Court
Full-duplex
double buffer
with or without parity supported
Built-in dedicated baud rate generator
External clock available as a serial clock
Hardware Flow control : Automatically control the
transmission by CTS/RTS (only ch.4)
Selection
•
San Jose, CA 95134-1709
•
408-943-2600
Revised May 25, 2017
S6E2H4 Series
Various
error detect functions available (parity errors,
framing errors, and overrun errors)
CSIO
Full-duplex
double buffer
Built-in dedicated baud rate generator
Overrun error detect function available
Serial chip select function (ch.6 and ch.7 only)
Supports high-speed SPI (ch.4 and ch.6 only)
Data length 5 to 16-bit
LIN
LIN
protocol Rev.2.1 supported
double buffer
Master/Slave mode supported
LIN break field generation (can change to 13 to 16-bit
length)
LIN break delimiter generation (can change to 1 to 4-bit
length)
Various error detect functions available (parity errors,
framing errors, and overrun errors)
Full-duplex
I2 C
Standard
mode (Max 100 kbps) / High-speed mode (Max
400 kbps) supported
Fast mode Plus (Fm+) (Max 1000 kbps, only for ch.3=ch.A
and ch.7=ch.B) supported
DMA Controller (8 channels)
DMA Controller has an independent bus for CPU, so CPU and
DMA Controller can process simultaneously.
Priority conversion available (priority at 2 levels)
Scanning conversion mode
Built-in FIFO for conversion data storage (for SCAN
conversion: 16 steps, for Priority conversion: 4 steps)
DA Converter (Max 2 channels)
R-2R type
12-bit resolution
Base Timer (Max 8 channels)
Operation mode is selectable from the followings for each
channel.
16-bit PWM timer
16-bit PPG timer
16-/32-bit reload timer
16-/32-bit PWC timer
Event counter mode ( external clock mode )
General Purpose I/O Port
This series can use its pins as general purpose I/O ports when
they are not used for external bus or peripherals. Moreover,
the port relocate function is built in. It can set which I/O port
the peripheral function can be allocated.
Capable of pull-up control per pin
8 independently configured and operated channels
Capable of reading pin level directly
Transfer can be started by software or request from the built-
Built-in the port relocate function
in peripherals
Transfer address area: 32-bit (4 Gbytes)
Transfer mode: Block transfer/Burst transfer/Demand
transfer
Up to 100 high-speed general-purpose I/O ports @ 120 pin
Package
Some pin is 5 V tolerant I/O.
Transfer data type: bytes/half-word/word
See 4. Pin Description and 5. I/O Circuit Type for the
corresponding pins.
Transfer block count: 1 to 16
Multi-function Timer (Max 3 units)
Number of transfers: 1 to 65536
The Multi-function timer is composed of the following blocks.
DSTC (Descriptor System data Transfer Controller)
(256 channels)
The DSTC can transfer data at high-speed without going via
the CPU. The DSTC adopts the Descriptor system and,
following the specified contents of the Descriptor which has
already been constructed on the memory, can access directly
the memory /peripheral device and performs the data transfer
operation.
It supports the software activation, the hardware activation and
the chain activation functions.
A/D Converter (Max 24 channels)
[12-bit A/D Converter]
Minimum resolution: 6.25 ns
16-bit free-run timer × 3ch./unit
Input capture × 4ch./unit
Output compare × 6ch./unit
A/D activation compare × 6ch./unit
Waveform generator × 3ch./unit
16-bit PPG timer × 3ch./unit
The following function can be used to achieve the motor
control.
PWM signal output function
Successive Approximation type
DC chopper waveform output function
Built-in 3 units
Dead time function
Conversion time: 0.5 μs @ 5 V
Input capture function
Document Number: 001-98941 Rev.*C
Page 2 of 160
S6E2H4 Series
A/D convertor activate function
DTIF (Motor emergency stop) interrupt function
Real-time Clock (RTC)
The Real-time clock can count
Year/Month/Day/Hour/Minute/Second/A day of the week from
00 to 99.
Interrupt function with specifying date and time
(Year/Month/Day/Hour/Minute/Second/A day of the week.) is
available. This function is also available by specifying only
Year, Month, Day, Hour or Minute.
Timer interrupt function after set time or each set time.
Hardware watchdog timer is clocked by low-speed internal CR
oscillator. Therefore, Hardware watchdog is active in any
power saving mode except Stop.
CRC (Cyclic Redundancy Check) Accelerator
The CRC accelerator helps a verify data transmission or
storage integrity.
CCITT CRC16 and IEEE-802.3 CRC32 are supported.
CCITT CRC16 Generator Polynomial: 0x1021
IEEE-802.3 CRC32 Generator Polynomial: 0x04C11DB7
Capable of rewriting the time with continuing the time count.
Clock and Reset
[Clocks]
Leap year automatic count is available.
Five clock sources (2 external oscillators, 2 internal CR
oscillator, and Main PLL) that are dynamically selectable.
Quadrature Position/Revolution Counter (QPRC)
(Max 3 channels)
Main clock: 4 MHz to 48 MHz
The Quadrature Position/Revolution Counter (QPRC) is used
to measure the position of the position encoder. Moreover, it is
possible to use up/down counter.
High-speed internal CR Clock: 4 MHz
The detection edge of the three external event input pins
Main PLL Clock
Sub Clock: 32.768 kHz
Low-speed internal CR Clock: 100 kHz
AIN, BIN and ZIN is configurable.
16-bit position counter
[Resets]
16-bit revolution counter
Reset requests from INITX pin
Two 16-bit compare registers
Power on reset
Dual Timer (32-/16-bit Down Counter)
The Dual Timer consists of two programmable 32-/16-bit down
counters.
Operation mode is selectable from the followings for each
channel.
Free-running
Periodic (=Reload)
One-shot
Watch Counter
Software reset
Watchdog timers reset
Low voltage detector reset
Clock supervisor reset
Clock SuperVisor (CSV)
Clocks generated by internal CR oscillators are used to
supervise abnormality of the external clocks.
External OSC clock failure (clock stop) is detected, reset is
asserted.
The Watch counter is used for wake up from the low-power
consumption mode. It is possible to select the main clock, sub
clock, built-in high-speed CR clock or built-in low-speed CR
clock as the clock source.
External OSC frequency anomaly is detected, interrupt or
Interval timer: up to 64 s (Max) @ Sub Clock: 32.768 kHz
External Interrupt Controller Unit
This Series include 2-stage monitoring of voltage on the VCC
pins. When the voltage falls below the voltage has been set,
Low-Voltage Detector generates an interrupt or reset.
External interrupt input pin: Max 16 pins
LVD1: error reporting via interrupt
Both
edges(Rise edge and Fall edge) detect
Include one non-maskable interrupt (NMI)
reset is asserted.
Low-Voltage Detector (LVD)
LVD2: auto-reset operation
Low-power Consumption Mode
Watchdog Timer (2 channels)
Six low-power consumption modes are supported.
A watchdog timer can generate interrupts or a reset when a
time-out value is reached.
Sleep
This series consists of two different watchdogs, a Hardware
watchdog and a Software watchdog.
RTC
Document Number: 001-98941 Rev.*C
Timer
Page 3 of 160
S6E2H4 Series
Stop
Deep standby RTC (selectable from with/without RAM
retention)
Deep standby stop (selectable from with/without RAM
retention)
VBAT
Port circuit
Debug
Serial Wire JTAG Debug Port (SWJ-DP)
Embedded Trace Macrocells (ETM) provide comprehensive
debug and trace facilities.
The consumption power during the RTC operation can be
reduced by supplying the power supply independent from the
RTC (calendar circuit)/32 kHz oscillation circuit. The following
circuits can also be used.
Unique ID
RTC
Two Power Supplies
32 kHz oscillation circuit
Wide range voltage:
Power-on circuit
Power supply for VBAT: VBAT = 2.7 V to 5.5 V
Unique value of the device (41-bit) is set.
Power Supply
VCC
= 2.7 V to 5.5 V
Back up register: 32 bytes
Document Number: 001-98941 Rev.*C
Page 4 of 160
S6E2H4 Series
Table of Contents
Features................................................................................................................................................................................... 1
1.
Product Lineup ............................................................................................................................................................... 7
2.
Packages......................................................................................................................................................................... 8
3.
Pin Assignment .............................................................................................................................................................. 9
4.
Pin Description ............................................................................................................................................................. 13
5.
I/O Circuit Type ............................................................................................................................................................. 43
6.
Handling Precautions .................................................................................................................................................. 50
6.1
Precautions for Product Design ................................................................................................................................... 50
6.2
Precautions for Package Mounting .............................................................................................................................. 51
6.3
Precautions for Use Environment ................................................................................................................................ 53
7.
Handling Devices ......................................................................................................................................................... 54
8.
Block Diagram .............................................................................................................................................................. 57
9.
Memory Size ................................................................................................................................................................. 58
10. Memory Map ................................................................................................................................................................. 58
11. Pin Status in Each CPU State ...................................................................................................................................... 61
12. Electrical Characteristics ............................................................................................................................................ 69
12.1 Absolute Maximum Ratings ......................................................................................................................................... 69
12.2 Recommended Operating Conditions.......................................................................................................................... 70
12.3 DC Characteristics....................................................................................................................................................... 73
12.3.1 Current Rating .............................................................................................................................................................. 73
12.3.2 Pin Characteristics ....................................................................................................................................................... 82
12.4 AC Characteristics ....................................................................................................................................................... 84
12.4.1 Main Clock Input Characteristics .................................................................................................................................. 84
12.4.2 Sub Clock Input Characteristics ................................................................................................................................... 85
12.4.3 Built-in CR Oscillation Characteristics .......................................................................................................................... 85
12.4.4 Operating Conditions of Main PLL (In the Case of Using Main Clock for Input Clock of PLL) ...................................... 86
12.4.5 Operating Conditions of Main PLL (In the Case of Using Built-in High-speed CR Clock for Input Clock
of Main PLL) ................................................................................................................................................................. 86
12.4.6 Reset Input Characteristics .......................................................................................................................................... 86
12.4.7 Power-on Reset Timing................................................................................................................................................ 87
12.4.8 GPIO Output Characteristics ........................................................................................................................................ 88
12.4.9 External Bus Timing ..................................................................................................................................................... 89
12.4.10 Base Timer Input Timing......................................................................................................................................... 101
12.4.11 CSIO Timing ........................................................................................................................................................... 102
12.4.12 External Input Timing .............................................................................................................................................. 135
12.4.13 Quadrature Position/Revolution Counter Timing .................................................................................................... 136
12.4.14 I2C Timing ............................................................................................................................................................... 138
12.4.15 ETM Timing ............................................................................................................................................................ 141
12.4.16 JTAG Timing ........................................................................................................................................................... 142
12.5 12-bit A/D Converter .................................................................................................................................................. 143
12.6 12-bit D/A Converter .................................................................................................................................................. 147
12.7 Low-Voltage Detection Characteristics ...................................................................................................................... 148
12.7.1 Low-Voltage Detection Reset ..................................................................................................................................... 148
12.7.2 Interrupt of Low-Voltage Detection ............................................................................................................................. 148
12.8 MainFlash Memory Write/Erase Characteristics........................................................................................................ 149
12.9 WorkFlash Memory Write/Erase Characteristics ....................................................................................................... 149
12.10 Standby Recovery Time ............................................................................................................................................ 150
12.10.1 Recovery Cause: Interrupt/WKUP .......................................................................................................................... 150
Document Number: 001-98941 Rev.*C
Page 5 of 160
S6E2H4 Series
12.10.2 Recovery Cause: Reset .......................................................................................................................................... 152
13. Ordering Information ................................................................................................................................................. 154
14. Package Dimensions ................................................................................................................................................. 155
Document History ............................................................................................................................................................... 159
Sales, Solutions, and Legal Information ........................................................................................................................... 160
Document Number: 001-98941 Rev.*C
Page 6 of 160
S6E2H4 Series
1. Product Lineup
Memory Size
Product name
MainFlash memory
WorkFlash memory
On-chip SRAM
SRAM0
SRAM1
SRAM2
S6E2H44E0A
S6E2H44F0A
S6E2H44G0A
256 Kbytes
32 Kbytes
32 Kbytes
16 Kbytes
8 Kbytes
8 Kbytes
S6E2H46E0A
S6E2H46F0A
S6E2H46G0A
512 Kbytes
32 Kbytes
64 Kbytes
32 Kbytes
16 Kbytes
16 Kbytes
Function
Product name
Pin count
CPU
Freq.
Power supply voltage range
CAN
DMAC
DSTC
External Bus Interface
S6E2H44F0A
S6E2H44G0A
S6E2H46F0A
S6E2H46G0A
100
120/121
Cortex-M4F, MPU, NVIC 128ch.
160 MHz
2.7 V to 5.5 V
2ch. (Max)
8ch.
256ch.
Addr:25-bit (Max),
Addr:25-bit (Max),
Addr:19-bit (Max),
R/W data: 8-/16-bit
R/W data: 8-/16-bit
R/W data: 8-bit
(Max),
(Max),
(Max),
CS:9 (Max),
CS:9 (Max),
CS:5 (Max),
SRAM,
SRAM,
SRAM,
NOR Flash,
NOR Flash,
NOR Flash
NAND Flash,
SDRAM
SDRAM
8ch. (Max)
8ch. (Max)
MF Timer
Multi-function Serial Interface
(UART/CSIO/LIN/I2C)
Base Timer
(PWC/Reload timer/PWM/PPG)
A/D activation
6ch.
compare
Input capture
4ch.
Free-run timer
3ch.
Output compare
6ch.
Waveform generator
3ch.
PPG
3ch.
QPRC
Dual Timer
Real-Time Clock
Watch Counter
CRC Accelerator
Watchdog Timer
External Interrupts
I/O Ports
12-bit A/D Converter
S6E2H44E0A
S6E2H46E0A
80
12-bit D/A Converter
CSV (Clock Super Visor)
LVD (Low-Voltage Detector)
High-speed
Built-in CR
Low-speed
Debug Function
Unique ID
Document Number: 001-98941 Rev.*C
3 units (Max)
63 pins (Max)
16ch. (3 units)
3ch. (Max)
1 unit
1 unit
1 unit
Yes
1ch. (SW) + 1ch. (HW)
16 pins (Max) + NMI × 1
80 pins (Max)
100 pins (Max)
24ch. (3 units)
2 units (Max)
Yes
2ch.
4 MHz (±2%)
100 kHz (Typ)
SWJ-DP/ETM
Yes
Page 7 of 160
S6E2H4 Series
Notes:
−
All signals of the peripheral function in each product cannot be allocated by limiting the pins of package.
It is necessary to use the port relocate function of the I/O port according to your function use.
−
See 12.4.3 Built-in CR Oscillation Characteristics for the accuracy of the built-in CR.
2. Packages
Product Name
Package
LQFP: LQH080 (0.5-mm pitch)
LQFP: LQI100 (0.5-mm pitch)
LQFP: LQM120 (0.5-mm pitch)
FBGA: FDI121 (0.5-mm pitch)
: Supported
S6E2H44E0A
S6E2H46E0A
-
-
S6E2H44F0A
S6E2H46F0A
-
-
S6E2H44G0A
S6E2H46G0A
Note :
−
See 14. Package Dimensions for detailed information on each package.
Document Number: 001-98941 Rev.*C
Page 8 of 160
S6E2H4 Series
3. Pin Assignment
LQH080
VSS
P81/IC20_0/AIN2_1
P80/IC21_0/BIN2_1
VCC
P60/SCK5_0/FRCK2_0/TIOA2_2/NMIX/WKUP0/MRDY_0
P61/SOT5_0/TIOB2_2/ZIN2_1/RTCCO_0/SUBOUT_0
P62/ADTG_3/SIN5_0/TX0_2/IC22_0/INT04_1/MOEX_0
P63/RX0_2/IC23_0/INT03_0/MWEX_0/CROUT_1
P00/TRSTX/MCSX7_0
P01/TCK/SWCLK
P02/TDI/MCSX6_0
P03/TMS/SWDIO
P04/TDO/SWO
P09/AN19/SOT1_0/IC23_1/TIOA3_2/MCSX5_0
P0A/SIN1_0/FRCK1_0/INT12_2/MCSX1_0
P0B/SIN6_1/IC10_0/TIOB6_1/INT00_1/MCSX0_0
P0C/SOT6_1/IC11_0/TIOA6_1/MALE_0
P0D/SCK6_1/IC12_0/TIOA5_2/MDQM0_0
P0E/SCS6_1/IC13_0/TIOB5_2/MDQM1_0
VCC
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
(TOP VIEW)
VCC
1
60
VSS
P50/CTS4_0/RTO10_0/AIN0_2/INT00_0/MADATA00_0
2
59
P21/AN17/SIN0_0/RTO24_0/INT06_1
P51/RTS4_0/RTO11_0/BIN0_2/INT01_0/MADATA01_0
3
58
P22/AN16/SOT0_0/RTO23_0/TIOB7_1/CROUT_0
P52/SCK4_0/RTO12_0/ZIN0_2/MADATA02_0
4
57
P23/AN15/SCK0_0/RTO00_1/TIOA7_1
P53/SOT4_0/RTO13_0/TIOA1_2/MADATA03_0
5
56
P1B/AN11/SCK4_1/IC02_1/MAD18_0
P54/SIN4_0/RTO14_0/TIOB1_2/INT02_0/MADATA04_0
6
55
P1A/AN10/SOT4_1/IC01_1/MAD17_0
P55/ADTG_1/SIN6_0/RTO15_0/INT07_2/MADATA05_0
7
54
P19/AN09/SIN4_1/IC00_1/INT05_1/MAD16_0
P56/SOT6_0/DTTI1X_0/INT08_2/MADATA06_0
8
53
P18/AN08/SCK2_2/DTTI2X_0/MAD15_0
P30/RTS4_2/RTO25_1/TIOB0_1/INT15_2/WKUP1/MADATA07_0
9
52
AVRH
P31/SIN3_1/DTTI2X_1/TIOB1_1/INT09_2/MADATA08_0
10
51
AVRL
P32/SOT3_1/TIOB2_1/INT10_1/MADATA09_0
11
50
AVSS
P33/ADTG_6/SCK3_1/TIOB3_1/INT04_0/MADATA10_0
12
49
AVCC
P39/ADTG_2/DTTI0X_0/RTCCO_2/SUBOUT_2
13
48
P17/AN07/SOT2_2/RTO20_0/AIN2_2/WKUP3/MAD14_0
P3A/RTO00_0/TIOA0_1/AIN0_0
14
47
P16/AN06/SIN2_2/RTO21_0/BIN2_2/INT14_1/MAD13_0
P3B/RTO01_0/TIOA1_1/BIN0_0
15
46
P15/AN05/SCK0_1/RTO22_0/ZIN2_2/MAD12_0
P3C/RTO02_0/TIOA2_1/ZIN0_0
16
45
P14/AN04/SOT0_1/IC03_2/MAD11_0
P3D/RTO03_0/TIOA3_1/MAD00_0
17
44
P13/AN03/SIN0_1/IC02_2/INT03_1/MAD10_0
P3E/RTO04_0/TIOA4_1/MAD01_0
18
43
P12/AN02/SCK1_1/IC01_2/MAD09_0/RTCCO_1/SUBOUT_1
P3F/RTO05_0/TIOA5_1/MAD02_0
19
42
P11/AN01/SOT1_1/TX1_2/IC00_2/MAD08_0
VSS
20
41
P10/AN00/SIN1_1/RX1_2/FRCK0_2/INT02_1/MAD07_0
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
P44/DA0/RTO14_1/TIOA4_0
P45/DA1/RTO15_1/TIOB0_0
INITX
P46/X0A
P47/X1A
P48/VREGCTL
P49/VWAKEUP
VBAT
C
VSS
VCC
P4B/SCS7_1/TIOB1_0/MAD03_0
P4C/SCK7_1/TIOB2_0/AIN1_2/MAD04_0
P4D/SOT7_1/TIOB3_0/BIN1_2/INT13_2/MAD05_0
P4E/SIN7_1/FRCK1_1/TIOB4_0/ZIN1_2/INT11_1/WKUP2/MAD06_0
PE0/MD1
MD0
PE2/X0
PE3/X1
VSS
LQFP - 80
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For
these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function
register (EPFR) to select the pin.
Document Number: 001-98941 Rev.*C
Page 9 of 160
S6E2H4 Series
LQI100
VSS
P81/IC20_0/AIN2_1
P80/IC21_0/BIN2_1
VCC
P60/SCK5_0/FRCK2_0/TIOA2_2/NMIX/WKUP0/MRDY_0
P61/SOT5_0/TIOB2_2/ZIN2_1/RTCCO_0/SUBOUT_0
P62/ADTG_3/SIN5_0/TX0_2/IC22_0/INT04_1/MOEX_0
P63/RX0_2/IC23_0/INT03_0/MWEX_0/CROUT_1
VSS
P00/TRSTX/MCSX7_0
P01/TCK/SWCLK
P02/TDI/MCSX6_0
P03/TMS/SWDIO
P04/TDO/SWO
P05/AN23/ADTG_0/SIN7_0/FRCK2_1/INT01_1/MCSX2_0/TRACECLK
P06/AN22/SOT7_0/IC20_1/TIOB0_2/MCSX3_0/TRACED3
P07/AN21/SCK7_0/IC21_1/TIOA0_2/MCLKOUT_0/TRACED2
P08/AN20/SCK1_0/IC22_1/TIOB3_2/MCSX4_0/TRACED1
P09/AN19/SOT1_0/IC23_1/TIOA3_2/MCSX5_0/TRACED0
P0A/SIN1_0/FRCK1_0/INT12_2/MCSX1_0
P0B/SIN6_1/IC10_0/TIOB6_1/INT00_1/MCSX0_0
P0C/SOT6_1/IC11_0/TIOA6_1/MALE_0
P0D/SCK6_1/IC12_0/TIOA5_2/MDQM0_0
P0E/SCS6_1/IC13_0/TIOB5_2/MDQM1_0
VCC
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
(TOP VIEW)
VCC
1
75
VSS
P50/CTS4_0/RTO10_0/AIN0_2/INT00_0/MADATA00_0
2
74
P20/AN18/RTO25_0/AIN1_1/INT05_0/MAD24_0
P51/RTS4_0/RTO11_0/BIN0_2/INT01_0/MADATA01_0
3
73
P21/AN17/SIN0_0/RTO24_0/BIN1_1/INT06_1/MAD23_0
P52/SCK4_0/RTO12_0/ZIN0_2/MADATA02_0
4
72
P22/AN16/SOT0_0/RTO23_0/TIOB7_1/ZIN1_1/CROUT_0
P53/SOT4_0/RTO13_0/TIOA1_2/MADATA03_0
5
71
P23/AN15/SCK0_0/RTO00_1/TIOA7_1/MAD22_0
P54/SIN4_0/RTO14_0/TIOB1_2/INT02_0/MADATA04_0
6
70
P1E/AN14/ADTG_5/FRCK0_1/MAD21_0
P55/ADTG_1/SIN6_0/RTO15_0/INT07_2/MADATA05_0
7
69
P1D/AN13/RTS4_1/DTTI0X_1/MAD20_0
P56/SOT6_0/DTTI1X_0/INT08_2/MADATA06_0
8
68
P1C/AN12/CTS4_1/IC03_1/MAD19_0
P30/RTS4_2/RTO25_1/TIOB0_1/INT15_2/WKUP1/MADATA07_0
9
67
P1B/AN11/SCK4_1/IC02_1/MAD18_0
P31/SIN3_1/DTTI2X_1/TIOB1_1/INT09_2/MADATA08_0
10
66
P1A/AN10/SOT4_1/IC01_1/MAD17_0
P32/SOT3_1/TIOB2_1/INT10_1/MADATA09_0
11
65
P19/AN09/SIN4_1/IC00_1/INT05_1/MAD16_0
P33/ADTG_6/SCK3_1/TIOB3_1/INT04_0/MADATA10_0
12
64
P18/AN08/SCK2_2/DTTI2X_0/MAD15_0
P34/TX0_1/FRCK0_0/TIOB4_1/MADATA11_0
13
63
AVRH
P35/RX0_1/IC03_0/TIOB5_1/INT08_1/MADATA12_0
14
62
AVRL
P36/SIN5_2/IC02_0/INT09_1/MADATA13_0
15
61
AVSS
P37/SOT5_2/IC01_0/INT05_2/MADATA14_0
16
60
AVCC
P38/SCK5_2/IC00_0/INT06_2/MADATA15_0
17
59
P17/AN07/SOT2_2/RTO20_0/AIN2_2/WKUP3/MAD14_0
P39/ADTG_2/DTTI0X_0/MSDCLK_0/RTCCO_2/SUBOUT_2
18
58
P16/AN06/SIN2_2/RTO21_0/BIN2_2/INT14_1/MAD13_0
P3A/RTO00_0/TIOA0_1/AIN0_0/MSDCKE_0
19
57
P15/AN05/SCK0_1/RTO22_0/ZIN2_2/MAD12_0
P3B/RTO01_0/TIOA1_1/BIN0_0/MRASX_0
20
56
P14/AN04/SOT0_1/IC03_2/MAD11_0
P3C/RTO02_0/TIOA2_1/ZIN0_0/MCASX_0
21
55
P13/AN03/SIN0_1/IC02_2/INT03_1/MAD10_0
P3D/RTO03_0/TIOA3_1/MAD00_0
22
54
P12/AN02/SCK1_1/IC01_2/MAD09_0/RTCCO_1/SUBOUT_1
P3E/RTO04_0/TIOA4_1/MAD01_0
23
53
P11/AN01/SOT1_1/TX1_2/IC00_2/MAD08_0
P3F/RTO05_0/TIOA5_1/MAD02_0
24
52
P10/AN00/SIN1_1/RX1_2/FRCK0_2/INT02_1/MAD07_0
VSS
25
51
VCC
35
36
37
38
39
40
41
42
43
44
45
46
P47/X1A
P48/VREGCTL
P49/VWAKEUP
VBAT
C
VSS
VCC
P4B/SCS7_1/TIOB1_0/MAD03_0
P4C/SCK7_1/TIOB2_0/AIN1_2/MAD04_0
P4D/SOT7_1/TIOB3_0/BIN1_2/INT13_2/MAD05_0
P4E/SIN7_1/FRCK1_1/TIOB4_0/ZIN1_2/INT11_1/WKUP2/MAD06_0
PE0/MD1
50
34
P46/X0A
VSS
33
INITX
49
32
P45/DA1/RTO15_1/TIOB0_0
48
31
P44/DA0/RTO14_1/TIOA4_0
PE3/X1
30
P43/ADTG_7/RTO13_1/TIOA3_0/ZIN2_0/MCSX8_0
47
29
P42/RTO12_1/TIOA2_0/BIN2_0/MDWEX_0
MD0
28
PE2/X0
27
26
VCC
P40/RTO10_1/TIOA0_0/INT12_1
P41/RTO11_1/TIOA1_0/AIN2_0/INT13_1
LQFP - 100
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For
these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function
register (EPFR) to select the pin.
Document Number: 001-98941 Rev.*C
Page 10 of 160
S6E2H4 Series
LQM120
VSS
P81/IC20_0/AIN2_1
P80/IC21_0/BIN2_1
VCC
P60/SCK5_0/FRCK2_0/TIOA2_2/NMIX/WKUP0/MRDY_0
P61/SOT5_0/TIOB2_2/ZIN2_1/RTCCO_0/SUBOUT_0
P62/ADTG_3/SIN5_0/TX0_2/IC22_0/INT04_1/MOEX_0
P63/SIN5_1/RX0_2/IC23_0/INT03_0/MWEX_0/CROUT_1
P64/SOT5_1/TIOA7_0/INT10_2
P65/SCK5_1/TIOB7_0
P66/ADTG_8/SIN3_0/INT11_2
P67/SOT3_0/TIOA7_2
P68/SCK3_0/TIOB7_2/INT00_2
VSS
P00/TRSTX/MCSX7_0
P01/TCK/SWCLK
P02/TDI/MCSX6_0
P03/TMS/SWDIO
P04/TDO/SWO
P05/AN23/ADTG_0/SIN7_0/FRCK2_1/INT01_1/MCSX2_0/TRACECLK
P06/AN22/SOT7_0/IC20_1/TIOB0_2/MCSX3_0/TRACED3
P07/AN21/SCK7_0/IC21_1/TIOA0_2/MCLKOUT_0/TRACED2
P08/AN20/SCK1_0/IC22_1/TIOB3_2/MCSX4_0/TRACED1
P09/AN19/SOT1_0/IC23_1/TIOA3_2/MCSX5_0/TRACED0
P0A/SIN1_0/FRCK1_0/INT12_2/MCSX1_0
P0B/SIN6_1/IC10_0/TIOB6_1/INT00_1/MCSX0_0
P0C/SOT6_1/IC11_0/TIOA6_1/MALE_0
P0D/SCK6_1/IC12_0/TIOA5_2/MDQM0_0
P0E/SCS6_1/IC13_0/TIOB5_2/MDQM1_0
VCC
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
(TOP VIEW)
VCC
1
90
VSS
P50/CTS4_0/RTO10_0/AIN0_2/INT00_0/MADATA00_0
2
89
P20/AN18/RTO25_0/AIN1_1/INT05_0/MAD24_0
P51/RTS4_0/RTO11_0/BIN0_2/INT01_0/MADATA01_0
3
88
P21/AN17/SIN0_0/RTO24_0/BIN1_1/INT06_1/MAD23_0
P52/SCK4_0/RTO12_0/ZIN0_2/MADATA02_0
4
87
P22/AN16/SOT0_0/RTO23_0/TIOB7_1/ZIN1_1/CROUT_0
P53/SOT4_0/RTO13_0/TIOA1_2/MADATA03_0
5
86
P23/AN15/SCK0_0/RTO00_1/TIOA7_1/MAD22_0
P54/SIN4_0/RTO14_0/TIOB1_2/INT02_0/MADATA04_0
6
85
P24/SIN2_1/RX1_0/RTO01_1/INT01_2
P55/ADTG_1/SIN6_0/RTO15_0/INT07_2/MADATA05_0
7
84
P25/SOT2_1/TX1_0/RTO02_1/TIOA5_0
P56/SOT6_0/DTTI1X_0/INT08_2/MADATA06_0
8
83
P26/SCK2_1/RTO03_1/TIOB5_0
P57/SCK6_0/RTO20_1/MADATA07_0
9
82
P27/RTO04_1/TIOA6_2/INT02_2
P58/SIN4_2/RTO21_1/AIN1_0/INT04_2/MADATA08_0
10
81
P1F/ADTG_4/RTO05_1/TIOB6_2
P59/SOT4_2/RX1_1/RTO22_1/BIN1_0/INT07_1/MADATA09_0
11
80
P1E/AN14/ADTG_5/FRCK0_1/MAD21_0
P5A/SCK4_2/TX1_1/RTO23_1/ZIN1_0/MADATA10_0
12
79
P1D/AN13/RTS4_1/DTTI0X_1/MAD20_0
P5B/CTS4_2/RTO24_1/MADATA11_0
13
78
P1C/AN12/CTS4_1/IC03_1/MAD19_0
P30/RTS4_2/RTO25_1/TIOB0_1/INT15_2/WKUP1/MADATA12_0
14
77
P1B/AN11/SCK4_1/IC02_1/MAD18_0
P31/SIN3_1/DTTI2X_1/TIOB1_1/INT09_2/MADATA13_0
15
76
P1A/AN10/SOT4_1/IC01_1/MAD17_0
P32/SOT3_1/TIOB2_1/INT10_1/MADATA14_0
16
75
P19/AN09/SIN4_1/IC00_1/INT05_1/MAD16_0
P33/ADTG_6/SCK3_1/TIOB3_1/INT04_0/MADATA15_0
17
74
P18/AN08/SCK2_2/DTTI2X_0/MAD15_0
P34/TX0_1/FRCK0_0/TIOB4_1/MNALE_0
18
73
AVRH
P35/RX0_1/IC03_0/TIOB5_1/INT08_1/MNCLE_0
19
72
AVRL
LQFP - 120
54
55
56
P73/SOT2_0/IC10_1/TIOB6_0/INT03_2
P74/SCK2_0/DTTI1X_1
PE0/MD1
60
53
P72/SIN2_0/IC11_1/TIOA6_0/ZIN0_1/INT14_2
VSS
52
P71/RX0_0/IC12_1/TIOB4_2/BIN0_1/INT15_1
59
51
P70/TX0_0/IC13_1/TIOA4_2/AIN0_1
58
50
P4E/SIN7_1/FRCK1_1/TIOB4_0/ZIN1_2/INT11_1/WKUP2/MAD06_0
PE3/X1
49
P4D/SOT7_1/TIOB3_0/BIN1_2/INT13_2/MAD05_0
57
48
MD0
47
P4C/SCK7_1/TIOB2_0/AIN1_2/MAD04_0
PE2/X0
46
VCC
45
VSS
P4B/SCS7_1/TIOB1_0/MAD03_0
44
VCC
43
VCC
C
P10/AN00/SIN1_1/RX1_2/FRCK0_2/INT02_1/MAD07_0
61
42
62
30
VBAT
29
VSS
P49/VWAKEUP
P11/AN01/SOT1_1/TX1_2/IC00_2/MAD08_0
P3F/RTO05_0/TIOA5_1/MAD02_0
41
63
P48/VREGCTL
28
40
P12/AN02/SCK1_1/IC01_2/MAD09_0/RTCCO_1/SUBOUT_1
P3E/RTO04_0/TIOA4_1/MAD01_0
39
P13/AN03/SIN0_1/IC02_2/INT03_1/MAD10_0
64
P47/X1A
65
27
P46/X0A
26
P3D/RTO03_0/TIOA3_1/MAD00_0
38
P14/AN04/SOT0_1/IC03_2/MAD11_0
P3C/RTO02_0/TIOA2_1/ZIN0_0/MCASX_0
INITX
66
37
25
36
P15/AN05/SCK0_1/RTO22_0/ZIN2_2/MAD12_0
P3B/RTO01_0/TIOA1_1/BIN0_0/MRASX_0
P45/DA1/RTO15_1/TIOB0_0
P16/AN06/SIN2_2/RTO21_0/BIN2_2/INT14_1/MAD13_0
67
35
68
24
P44/DA0/RTO14_1/TIOA4_0
23
P3A/RTO00_0/TIOA0_1/AIN0_0/MSDCKE_0
P43/ADTG_7/RTO13_1/TIOA3_0/ZIN2_0/MCSX8_0
P17/AN07/SOT2_2/RTO20_0/AIN2_2/WKUP3/MAD14_0
P39/ADTG_2/DTTI0X_0/MSDCLK_0/RTCCO_2/SUBOUT_2
34
69
P42/RTO12_1/TIOA2_0/BIN2_0/MDWEX_0
22
33
AVCC
P38/SCK5_2/IC00_0/INT06_2
32
AVSS
70
31
71
21
P40/RTO10_1/TIOA0_0/INT12_1
20
P41/RTO11_1/TIOA1_0/AIN2_0/INT13_1
P36/SIN5_2/IC02_0/INT09_1/MNWEX_0
P37/SOT5_2/IC01_0/INT05_2/MNREX_0
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For
these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function
register (EPFR) to select the pin.
Document Number: 001-98941 Rev.*C
Page 11 of 160
S6E2H4 Series
FDI121
(TOP VIEW)
1
2
3
4
5
6
7
8
9
10
11
A
VSS
P81
P80
VCC
TRSTX
VSS
P06
P0A
P0D
VCC
VSS
B
VCC
P60
P61
P63
TCK
TDO
P07
P0B
P0E
P24
P20
C
P50
P51
P62
P64
TDI
TMS
P08
P0C
P25
P22
P21
D
P52
P53
P54
P65
P66
P05
P09
P26
P1E
P1D
P23
E
P30
P55
P56
P57
P67
P68
P27
P1C
P1B
P1A
P19
F
P34
P33
P32
P31
P58
P59
P1F
P18
P17
P16
AVRH
G
P35
P36
P37
P38
P5A
P5B
P72
P15
P14
P13
AVRL
H
P39
P3A
P3B
P3C
P43
P70
P71
P73
P12
P11
AVSS
J
P3D
P3E
P41
P45
P42
P4B
P4C
P4D
P74
P10
AVCC
K
VCC
P3F
P44
X1A
P48
P49
VCC
P4E
MD0
VSS
VCC
L
VSS
P40
INITX
X0A
VBAT
C
VSS
MD1
X0
X1
VSS
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For
these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function
register (EPFR) to select the pin.
Document Number: 001-98941 Rev.*C
Page 12 of 160
S6E2H4 Series
4. Pin Description
List of Pin Numbers
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR)
to select the pin.
Pin Number
Pin Name
LQFP120 LQFP100 LQFP80 FBGA121
I/O
Circuit
Type
Pin State
Type
1
1
1
B1
VCC
P50
CTS4_0
AIN0_2
-
-
2
2
2
C1
RTO10_0
(PPG10_0)
E
K
E
K
E
I
E
I
E
K
INT00_0
MADATA00_0
P51
RTS4_0
BIN0_2
3
3
3
C2
RTO11_0
(PPG10_0)
INT01_0
MADATA01_0
P52
SCK4_0
(SCL4_0)
4
4
4
D1
ZIN0_2
RTO12_0
(PPG12_0)
MADATA02_0
P53
TIOA1_2
5
5
5
D2
SOT4_0
(SDA4_0)
RTO13_0
(PPG12_0)
MADATA03_0
P54
TIOB1_2
SIN4_0
6
6
6
D3
RTO14_0
(PPG14_0)
INT02_0
MADATA04_0
Document Number: 001-98941 Rev.*C
Page 13 of 160
S6E2H4 Series
Pin Number
Pin Name
LQFP120 LQFP100 LQFP80 FBGA121
I/O
Circuit
Type
Pin State
Type
E
K
E
K
E
I
E
K
E
K
E
I
E
I
P55
ADTG_1
SIN6_0
7
7
7
E2
RTO15_0
(PPG14_0)
INT07_2
MADATA05_0
P56
8
8
8
E3
9
-
-
E4
10
-
-
F5
11
-
-
F6
SOT6_0
(SDA6_0)
DTTI1X_0
INT08_2
MADATA06_0
P57
SCK6_0
(SCL6_0)
MADATA07_0
RTO20_1
P58
SIN4_2
AIN1_0
INT04_2
MADATA08_0
RTO21_1
P59
SOT4_2
(SDA4_2)
BIN1_0
INT07_1
MADATA09_0
RTO22_1
RX1_1
P5A
SCK4_2
(SCL4_2)
12
-
-
G5
13
-
-
G6
Document Number: 001-98941 Rev.*C
ZIN1_0
MADATA10_0
RTO23_1
TX1_1
P5B
CTS4_2
MADATA11_0
RTO24_1
Page 14 of 160
S6E2H4 Series
Pin Number
Pin Name
LQFP120 LQFP100 LQFP80 FBGA121
14
9
9
14
15
9
9
10
10
15
16
16
17
17
18
18
19
19
E1
E1
F4
10
10
11
11
-
-
12
12
-
-
13
-
-
-
14
-
-
-
Document Number: 001-98941 Rev.*C
F4
F3
F3
F2
F2
F1
F1
G1
G1
P30
TIOB0_1
RTS4_2
INT15_2
WKUP1
MADATA07_0
MADATA12_0
RTO25_1
P31
TIOB1_1
SIN3_1
INT09_2
MADATA08_0
MADATA13_0
DTTI2X_1
P32
TIOB2_1
SOT3_1
(SDA3_1)
I/O
Circuit
Type
Pin State
Type
E
Q
I
K
N
K
N
K
E
I
E
K
INT10_1
MADATA09_0
MADATA14_0
P33
ADTG_6
TIOB3_1
SCK3_1
(SCL3_1)
INT04_0
MADATA10_0
MADATA15_0
P34
TIOB4_1
FRCK0_0
TX0_1
MADATA11_0
MNALE_0
P35
TIOB5_1
IC03_0
INT08_1
RX0_1
MADATA12_0
MNCLE_0
Page 15 of 160
S6E2H4 Series
Pin Number
LQFP120
20
20
21
21
22
LQFP100
LQFP80
15
-
-
-
16
-
-
-
17
-
-
23
Pin Name
FBGA121
G2
G2
G3
G3
G4
-
18
13
H1
-
24
19
14
H2
-
25
20
15
H3
-
26
21
16
H4
-
27
22
17
P36
SIN5_2
IC02_0
INT09_1
MADATA13_0
MNWEX_0
P37
I/O
Circuit
Type
Pin State
Type
E
K
E
K
E
K
L
I
G
I
G
I
G
I
G
I
SOT5_2
(SDA5_2)
IC01_0
INT05_2
MADATA14_0
MNREX_0
P38
SCK5_2
(SCL5_2)
IC00_0
INT06_2
MADATA15_0
P39
ADTG_2
DTTI0X_0
RTCCO_2
SUBOUT_2
MSDCLK_0
P3A
TIOA0_1
AIN0_0
RTO00_0
(PPG00_0)
MSDCKE_0
P3B
TIOA1_1
BIN0_0
RTO01_0
(PPG00_0)
MRASX_0
P3C
TIOA2_1
ZIN0_0
RTO02_0
(PPG02_0)
MCASX_0
P3D
TIOA3_1
J1
RTO03_0
(PPG02_0)
MAD00_0
Document Number: 001-98941 Rev.*C
Page 16 of 160
S6E2H4 Series
Pin Number
LQFP120
LQFP100
LQFP80
Pin Name
FBGA121
I/O
Circuit
Type
Pin State
Type
G
I
G
I
-
-
G
K
G
K
G
I
G
I
R
J
R
J
B
P
C
S
P3E
TIOA4_1
28
23
18
J2
RTO04_0
(PPG04_0)
MAD01_0
P3F
TIOA5_1
29
24
19
K2
30
31
25
26
20
-
L1
K1
32
27
-
L2
33
28
-
J3
RTO05_0
(PPG04_0)
MAD02_0
VSS
VCC
P40
TIOA0_0
RTO10_1
(PPG10_1)
INT12_1
P41
TIOA1_0
RTO11_1
(PPG10_1)
INT13_1
AIN2_0
P42
TIOA2_0
34
29
-
J5
RTO12_1
(PPG12_1)
MSDWEX_0
BIN2_0
P43
ADTG_7
TIOA3_0
35
30
-
H5
RTO13_1
(PPG12_1)
MCSX8_0
ZIN2_0
P44
TIOA4_0
36
31
21
K3
RTO14_1
(PPG14_1)
DA0
P45
TIOB0_0
37
38
39
32
33
34
22
23
24
Document Number: 001-98941 Rev.*C
J4
L3
L4
RTO15_1
(PPG14_1)
DA1
INITX
P46
Page 17 of 160
S6E2H4 Series
Pin Number
LQFP120
LQFP100
LQFP80
Pin Name
FBGA121
40
35
25
K4
41
36
26
K5
42
37
27
K6
43
44
45
46
38
39
40
41
28
29
30
31
L5
L6
L7
K7
47
42
32
J6
48
43
33
J7
X0A
P47
X1A
P48
VREGCTL
P49
VWAKEUP
VBAT
C
VSS
VCC
P4B
TIOB1_0
SCS7_1
MAD03_0
P4C
TIOB2_0
SCK7_1
(SCL7_1)
I/O
Circuit
Type
Pin State
Type
Q
T
O
U
O
U
-
-
E
I
N
I
N
K
I
Q
E
I
AIN1_2
MAD04_0
P4D
TIOB3_0
49
50
44
45
34
35
J8
K8
SOT7_1
(SDA7_1)
BIN1_2
INT13_2
MAD05_0
P4E
TIOB4_0
SIN7_1
ZIN1_2
FRCK1_1
INT11_1
WKUP2
MAD06_0
P70
TIOA4_2
51
-
-
H6
AIN0_1
IC13_1
TX0_0
Document Number: 001-98941 Rev.*C
Page 18 of 160
S6E2H4 Series
Pin Number
LQFP120
LQFP100
LQFP80
Pin Name
FBGA121
52
-
-
H7
53
-
-
G7
54
-
-
H8
P71
TIOB4_2
BIN0_1
IC12_1
INT15_1
RX0_0
P72
TIOA6_0
SIN2_0
ZIN0_1
IC11_1
INT14_2
P73
TIOB6_0
SOT2_0
(SDA2_0)
I/O
Circuit
Type
Pin State
Type
E
K
E
K
E
K
E
I
C
E
J
D
A
A
A
B
-
-
F
M
F
L
IC10_1
INT03_2
P74
55
-
-
J9
56
46
36
L8
57
47
37
K9
58
48
38
L9
59
49
39
L10
60
61
50
51
40
-
L11
K11
SCK2_0
(SCL2_0)
DTTI1X_1
PE0
MD1
MD0
PE2
X0
PE3
X1
VSS
VCC
P10
AN00
62
52
41
J10
SIN1_1
FRCK0_2
INT02_1
MAD07_0
RX1_2
P11
AN01
SOT1_1
(SDA1_1)
63
53
42
H10
IC00_2
MAD08_0
TX1_2
Document Number: 001-98941 Rev.*C
Page 19 of 160
S6E2H4 Series
Pin Number
LQFP120
LQFP100
LQFP80
Pin Name
FBGA121
I/O
Circuit
Type
Pin State
Type
F
L
F
M
F
L
F
L
F
M
F
P
-
-
P12
AN02
64
54
43
H9
65
55
44
G10
66
56
45
G9
SCK1_1
(SCL1_1)
IC01_2
RTCCO_1
SUBOUT_1
MAD09_0
P13
AN03
SIN0_1
IC02_2
INT03_1
MAD10_0
P14
AN04
SOT0_1
(SDA0_1)
IC03_2
MAD11_0
P15
AN05
67
68
57
58
46
47
G8
F10
69
59
48
F9
70
71
72
73
60
61
62
63
49
50
51
52
J11
H11
G11
F11
Document Number: 001-98941 Rev.*C
SCK0_1
(SCL0_1)
MAD12_0
ZIN2_2
RTO22_0
P16
AN06
SIN2_2
INT14_1
MAD13_0
BIN2_2
RTO21_0
P17
AN07
SOT2_2
(SDA2_2)
WKUP3
MAD14_0
AIN2_2
RTO20_0
AVCC
AVSS
AVRL
AVRH
Page 20 of 160
S6E2H4 Series
Pin Number
LQFP120
LQFP100
LQFP80
Pin Name
FBGA121
I/O
Circuit
Type
Pin State
Type
P18
AN08
74
64
53
F8
SCK2_2
(SCL2_2)
F
L
F
M
M
L
M
L
F
L
F
L
F
L
E
I
75
65
54
E11
MAD15_0
DTTI2X_0
P19
AN09
SIN4_1
IC00_1
INT05_1
MAD16_0
P1A
AN10
76
66
55
E10
SOT4_1
(SDA4_1)
IC01_1
MAD17_0
P1B
AN11
77
67
56
E9
78
68
-
E8
79
69
-
D10
80
70
-
D9
81
-
-
F7
SCK4_1
(SCL4_1)
IC02_1
MAD18_0
P1C
AN12
CTS4_1
IC03_1
MAD19_0
P1D
AN13
RTS4_1
DTTI0X_1
MAD20_0
P1E
AN14
ADTG_5
FRCK0_1
MAD21_0
P1F
ADTG_4
TIOB6_2
RTO05_1
(PPG04_1)
Document Number: 001-98941 Rev.*C
Page 21 of 160
S6E2H4 Series
Pin Number
LQFP120
LQFP100
LQFP80
Pin Name
FBGA121
I/O
Circuit
Type
Pin State
Type
E
K
E
I
E
I
E
K
F
L
F
L
F
M
P27
TIOA6_2
82
-
-
E7
RTO04_1
(PPG04_1)
INT02_2
P26
TIOB5_0
83
-
-
D8
SCK2_1
(SCL2_1)
RTO03_1
(PPG02_1)
P25
TIOA5_0
84
-
-
C9
SOT2_1
(SDA2_1)
RTO02_1
(PPG02_1)
TX1_0
P24
SIN2_1
85
-
-
B10
RTO01_1
(PPG00_1)
INT01_2
RX1_0
P23
AN15
TIOA7_1
86
71
57
D11
SCK0_0
(SCL0_0)
RTO00_1
(PPG00_1)
-
58
87
72
C10
58
59
88
73
59
59
Document Number: 001-98941 Rev.*C
C11
MAD22_0
P22
CROUT_0
AN16
TIOB7_1
SOT0_0
(SDA0_0)
ZIN1_1
RTO23_0
P21
AN17
SIN0_0
BIN1_1
INT06_1
MAD23_0
RTO24_0
Page 22 of 160
S6E2H4 Series
Pin Number
LQFP120
LQFP100
LQFP80
Pin Name
FBGA121
89
74
-
B11
90
91
75
76
60
61
A11
A10
92
77
62
B9
P20
AN18
AIN1_1
INT05_0
MAD24_0
RTO25_0
VSS
VCC
P0E
TIOB5_2
SCS6_1
I/O
Circuit
Type
Pin State
Type
F
M
-
-
L
I
L
I
L
I
L
K
L
K
IC13_0
MDQM1_0
P0D
TIOA5_2
93
78
63
A9
SCK6_1
(SCL6_1)
IC12_0
MDQM0_0
P0C
TIOA6_1
94
79
64
C8
SOT6_1
(SDA6_1)
B8
MALE_0
P0B
TIOB6_1
SIN6_1
IC10_0
IC11_0
95
80
65
INT00_1
MCSX0_0
P0A
SIN1_0
96
81
66
A8
FRCK1_0
INT12_2
MCSX1_0
Document Number: 001-98941 Rev.*C
Page 23 of 160
S6E2H4 Series
Pin Number
LQFP120
LQFP100
LQFP80
Pin Name
FBGA121
82
D7
67
98
99
100
83
84
85
-
-
-
C7
B7
A7
101
86
-
D6
102
87
68
B6
103
88
69
C6
Document Number: 001-98941 Rev.*C
Pin State
Type
M
N
F
N
M
N
F
N
F
O
E
G
E
G
P09
AN19
TRACED0
TIOA3_2
67
97
I/O
Circuit
Type
SOT1_0
(SDA1_0)
MCSX5_0
IC23_1
P08
AN20
TRACED1
TIOB3_2
SCK1_0
(SCL1_0)
MCSX4_0
IC22_1
P07
AN21
TRACED2
TIOA0_2
SCK7_0
(SCL7_0)
MCLKOUT_0
IC21_1
P06
AN22
TRACED3
TIOB0_2
SOT7_0
(SDA7_0)
MCSX3_0
IC20_1
P05
AN23
ADTG_0
TRACECLK
SIN7_0
INT01_1
MCSX2_0
FRCK2_1
P04
TDO
SWO
P03
TMS
SWDIO
Page 24 of 160
S6E2H4 Series
Pin Number
Pin Name
LQFP120
LQFP100
LQFP80
FBGA121
104
89
70
C5
105
90
71
B5
106
91
72
A5
107
92
-
A6
108
-
-
E6
109
-
-
E5
110
-
-
D5
111
-
-
D4
112
-
-
C4
93
73
-
-
113
B4
93
114
94
73
74
Document Number: 001-98941 Rev.*C
P02
TDI
MCSX6_0
P01
TCK
SWCLK
P00
TRSTX
MCSX7_0
VSS
P68
TIOB7_2
SCK3_0
(SCL3_0)
INT00_2
P67
TIOA7_2
SOT3_0
(SDA3_0)
P66
ADTG_8
SIN3_0
INT11_2
P65
TIOB7_0
SCK5_1
(SCL5_1)
P64
TIOA7_0
SOT5_1
(SDA5_1)
INT10_2
P63
CROUT_1
SIN5_1
INT03_0
MWEX_0
I/O
Circuit
Type
Pin State
Type
E
H
E
G
E
H
-
-
E
K
E
I
E
K
E
I
E
K
E
K
I
K
IC23_0
C3
RX0_2
P62
ADTG_3
SIN5_0
INT04_1
MOEX_0
IC22_0
TX0_2
Page 25 of 160
S6E2H4 Series
Pin Number
LQFP120
LQFP100
LQFP80
Pin Name
FBGA121
I/O
Circuit
Type
Pin State
Type
E
I
I
F
-
-
E
*1
I
E
*1
I
-
-
P61
TIOB2_2
115
95
75
B3
SOT5_0
(SDA5_0)
RTCCO_0
SUBOUT_0
ZIN2_1
P60
TIOA2_2
116
96
76
B2
117
97
77
A4
118
98
78
A3
119
99
79
A2
120
100
80
*1 without pullup control register
A1
K10
Document Number: 001-98941 Rev.*C
SCK5_0
(SCL5_0)
NMIX
WKUP0
MRDY_0
FRCK2_0
VCC
P80
BIN2_1
IC21_0
P81
AIN2_1
IC20_0
VSS
VSS
Page 26 of 160
S6E2H4 Series
List of Pin Functions
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR)
to select the pin.
Pin
Function
ADC
Base Timer
0
Pin Name
ADTG_0
ADTG_1
ADTG_2
ADTG_3
ADTG_4
ADTG_5
ADTG_6
ADTG_7
ADTG_8
AN00
AN01
AN02
AN03
AN04
AN05
AN06
AN07
AN08
AN09
AN10
AN11
AN12
AN13
AN14
AN15
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
TIOA0_0
TIOA0_1
TIOA0_2
TIOB0_0
TIOB0_1
TIOB0_2
Function Description
A/D converter external trigger input pin
A/D converter analog input pin.
ANxx describes ADC ch.xx.
Base timer ch.0 TIOA pin
Base timer ch.0 TIOB pin
Document Number: 001-98941 Rev.*C
LQFP
120
101
7
23
114
81
80
17
35
110
62
63
64
65
66
67
68
69
74
75
76
77
78
79
80
86
87
88
89
97
98
99
100
101
32
24
99
37
14
100
Pin No
LQFP LQFP
100
80
86
7
7
18
13
94
74
70
12
12
30
52
41
53
42
54
43
55
44
56
45
57
46
58
47
59
48
64
53
65
54
66
55
67
56
68
69
70
71
57
72
58
73
59
74
82
67
83
84
85
86
27
19
14
84
32
22
9
9
85
-
FBGA
121
D6
E2
H1
C3
F7
D9
F2
H5
D5
J10
H10
H9
G10
G9
G8
F10
F9
F8
E11
E10
E9
E8
D10
D9
D11
C10
C11
B11
D7
C7
B7
A7
D6
L2
H2
B7
J4
E1
A7
Page 27 of 160
S6E2H4 Series
Pin
Function
Base Timer
1
Base Timer
2
Base Timer
3
Base Timer
4
Base Timer
5
Base Timer
6
Pin Name
TIOA1_0
TIOA1_1
TIOA1_2
TIOB1_0
TIOB1_1
TIOB1_2
TIOA2_0
TIOA2_1
TIOA2_2
TIOB2_0
TIOB2_1
TIOB2_2
TIOA3_0
TIOA3_1
TIOA3_2
TIOB3_0
TIOB3_1
TIOB3_2
TIOA4_0
TIOA4_1
TIOA4_2
TIOB4_0
TIOB4_1
TIOB4_2
TIOA5_0
TIOA5_1
TIOA5_2
TIOB5_0
TIOB5_1
TIOB5_2
TIOA6_0
TIOA6_1
TIOA6_2
TIOB6_0
TIOB6_1
TIOB6_2
Function Description
Base timer ch.1 TIOA pin
Base timer ch.1 TIOB pin
Base timer ch.2 TIOA pin
Base timer ch.2 TIOB pin
Base timer ch.3 TIOA pin
Base timer ch.3 TIOB pin
Base timer ch.4 TIOA pin
Base timer ch.4 TIOB pin
Base timer ch.5 TIOA pin
Base timer ch.5 TIOB pin
Base timer ch.6 TIOA pin
Base timer ch.6 TIOB pin
TIOA7_0
Pin No
LQFP LQFP
100
80
28
20
15
5
5
42
32
10
10
6
6
29
21
16
96
76
43
33
11
11
95
75
30
22
17
82
67
44
34
12
12
83
31
21
23
18
45
35
13
24
19
78
63
14
77
62
79
64
80
65
-
FBGA
121
J3
H3
D2
J6
F4
D3
J5
H4
B2
J7
F3
B3
H5
J1
D7
J8
F2
C7
K3
J2
H6
K8
F1
H7
C9
K2
A9
D8
G1
B9
G7
C8
E7
H8
B8
F7
112
-
-
C4
86
71
57
D11
TIOA7_2
109
-
-
E5
TIOB7_0
111
-
-
D4
87
72
58
C10
108
-
-
E6
TIOA7_1
Base Timer
7
LQFP
120
33
25
5
47
15
6
34
26
116
48
16
115
35
27
97
49
17
98
36
28
51
50
18
52
84
29
93
83
19
92
53
94
82
54
95
81
TIOB7_1
Base timer ch.7 TIOA pin
Base timer ch.7 TIOB pin
TIOB7_2
Document Number: 001-98941 Rev.*C
Page 28 of 160
S6E2H4 Series
Pin
Function
Pin Name
SWCLK
SWDIO
Debugger
External
Bus
SWO
TCK
TDI
TDO
TMS
TRACECLK
TRACED0
TRACED1
TRACED2
TRACED3
TRSTX
MAD00_0
MAD01_0
MAD02_0
MAD03_0
MAD04_0
MAD05_0
MAD06_0
MAD07_0
MAD08_0
MAD09_0
MAD10_0
MAD11_0
MAD12_0
MAD13_0
MAD14_0
MAD15_0
MAD16_0
MAD17_0
MAD18_0
MAD19_0
MAD20_0
MAD21_0
MAD22_0
MAD23_0
MAD24_0
Function Description
Serial wire debug interface clock input pin
Serial wire debug interface data input /
output pin
Serial wire viewer output pin
JTAG test clock input pin
JTAG test data input pin
JTAG debug data output pin
JTAG test mode state input/output pin
Trace CLK output pin of ETM
Trace data output pin of ETM
JTAG test reset Input pin
External bus interface address bus
Document Number: 001-98941 Rev.*C
LQFP
120
105
Pin No
LQFP LQFP
100
80
90
71
FBGA
121
B5
103
88
69
C6
102
105
104
102
103
101
97
98
99
100
106
27
28
29
47
48
49
50
62
63
64
65
66
67
68
69
74
75
76
77
78
79
80
86
88
89
87
90
89
87
88
86
82
83
84
85
91
22
23
24
42
43
44
45
52
53
54
55
56
57
58
59
64
65
66
67
68
69
70
71
73
74
68
71
70
68
69
72
17
18
19
32
33
34
35
41
42
43
44
45
46
47
48
53
54
55
56
-
B6
B5
C5
B6
C6
D6
D7
C7
B7
A7
A5
J1
J2
K2
J6
J7
J8
K8
J10
H10
H9
G10
G9
G8
F10
F9
F8
E11
E10
E9
E8
D10
D9
D11
C11
B11
Page 29 of 160
S6E2H4 Series
Pin
Function
External
Bus
Pin Name
MCSX0_0
MCSX1_0
MCSX2_0
MCSX3_0
MCSX4_0
MCSX5_0
MCSX6_0
MCSX7_0
MCSX8_0
MADATA00_0
MADATA01_0
MADATA02_0
MADATA03_0
MADATA04_0
MADATA05_0
MADATA06_0
MADATA07_0
MADATA08_0
MADATA09_0
MADATA10_0
MADATA11_0
MADATA12_0
MADATA13_0
MADATA14_0
MADATA15_0
MDQM0_0
MDQM1_0
MALE_0
MRDY_0
MCLKOUT_0
MNALE_0
MNCLE_0
MNREX_0
MNWEX_0
MOEX_0
MWEX_0
Function Description
External bus interface chip select output
pin
External bus interface data bus
(Address / data multiplex bus)
External bus interface byte mask signal
output pin
External bus interface Address Latch
enable output signal for multiplex
External bus interface external RDY input
signal
External bus interface external clock output
pin
External bus interface ALE signal to control
NAND Flash output pin
External bus interface CLE signal to
control NAND Flash output pin
External bus interface read enable signal
to control NAND Flash
External bus interface write enable signal
to control NAND Flash
External bus interface read enable signal
for SRAM
External bus interface write enable signal
for SRAM
Document Number: 001-98941 Rev.*C
LQFP
120
95
96
101
100
98
97
104
106
35
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
93
92
Pin No
LQFP LQFP
100
80
80
65
81
66
86
85
83
82
67
89
70
91
72
30
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
14
15
16
17
78
63
77
62
FBGA
121
B8
A8
D6
A7
C7
D7
C5
A5
H5
C1
C2
D1
D2
D3
E2
E3
E4
F5
F6
G5
G6
E1
F4
F3
F2
A9
B9
94
79
64
C8
116
96
76
B2
99
84
-
B7
18
-
-
F1
19
-
-
G1
21
-
-
G3
20
-
-
G2
114
94
74
C3
113
93
73
B4
Page 30 of 160
S6E2H4 Series
Pin
Function
Pin Name
MSDCLK_0
MSDCKE_0
External
Bus
MRASX_0
MCASX_0
MSDWEX_0
External
Interrupt
INT00_0
INT00_1
INT00_2
INT01_0
INT01_1
INT01_2
INT02_0
INT02_1
INT02_2
INT03_0
INT03_1
INT03_2
INT04_0
INT04_1
INT04_2
INT05_0
INT05_1
INT05_2
INT06_1
INT06_2
INT07_1
INT07_2
INT08_1
INT08_2
INT09_1
INT09_2
INT10_1
INT10_2
INT11_1
INT11_2
INT12_1
INT12_2
INT13_1
INT13_2
INT14_1
INT14_2
INT15_1
INT15_2
Function Description
SDRAM interface
SDRAM clock output pin
SDRAM interface
SDRAM clock enable pin
SDRAM interface
SDRAM row address strobe pin
SDRAM interface
SDRAM column address strobe pin
SDRAM interface
SDRAM write enable pin
External interrupt request 00 input pin
External interrupt request 01 input pin
External interrupt request 02 input pin
External interrupt request 03 input pin
External interrupt request 04 input pin
External interrupt request 05 input pin
External interrupt request 06 input pin
External interrupt request 07 input pin
External interrupt request 08 input pin
External interrupt request 09 input pin
External interrupt request 10 input pin
External interrupt request 11 input pin
External interrupt request 12 input pin
External interrupt request 13 input pin
External interrupt request 14 input pin
External interrupt request 15 input pin
Document Number: 001-98941 Rev.*C
LQFP
120
Pin No
LQFP LQFP
100
80
FBGA
121
23
18
-
H1
24
19
-
H2
25
20
-
H3
26
21
-
H4
34
29
-
J5
2
95
108
3
101
85
6
62
82
113
65
54
17
114
10
89
75
21
88
22
11
7
19
8
20
15
16
112
50
110
32
96
33
49
68
53
52
14
2
80
3
86
6
52
93
55
12
94
74
65
16
73
17
7
14
8
15
10
11
45
27
81
28
44
58
9
2
65
3
6
41
73
44
12
74
54
59
7
8
10
11
35
66
34
47
9
C1
B8
E6
C2
D6
B10
D3
J10
E7
B4
G10
H8
F2
C3
F5
B11
E11
G3
C11
G4
F6
E2
G1
E3
G2
F4
F3
C4
K8
D5
L2
A8
J3
J8
F10
G7
H7
E1
Page 31 of 160
S6E2H4 Series
Pin
Function
Pin Name
External
Interrupt
NMIX
GPIO
P00
P01
P02
P03
P04
P05
P06
P07
P08
P09
P0A
P0B
P0C
P0D
P0E
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P1A
P1B
P1C
P1D
P1E
P1F
P20
P21
P22
P23
P24
P25
P26
P27
Function Description
Non-Maskable Interrupt input pin
General-purpose I/O port 0
General-purpose I/O port 1
General-purpose I/O port 2
Document Number: 001-98941 Rev.*C
LQFP
120
Pin No
LQFP LQFP
100
80
FBGA
121
116
96
76
B2
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
62
63
64
65
66
67
68
69
74
75
76
77
78
79
80
81
89
88
87
86
85
84
83
82
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
52
53
54
55
56
57
58
59
64
65
66
67
68
69
70
74
73
72
71
-
72
71
70
69
68
67
66
65
64
63
62
41
42
43
44
45
46
47
48
53
54
55
56
59
58
57
-
A5
B5
C5
C6
B6
D6
A7
B7
C7
D7
A8
B8
C8
A9
B9
J10
H10
H9
G10
G9
G8
F10
F9
F8
E11
E10
E9
E8
D10
D9
F7
B11
C11
C10
D11
B10
C9
D8
E7
Page 32 of 160
S6E2H4 Series
Pin
Function
Pin Name
GPIO
P30
P31
P32
P33
P34
P35
P36
P37
P38
P39
P3A
P3B
P3C
P3D
P3E
P3F
P40
P41
P42
P43
P44
P45
P46
P47
P48
P49
P4B
P4C
P4D
P4E
P50
P51
P52
P53
P54
P55
P56
P57
P58
P59
P5A
P5B
Function Description
General-purpose I/O port 3
General-purpose I/O port 4
General-purpose I/O port 5
Document Number: 001-98941 Rev.*C
LQFP
120
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
32
33
34
35
36
37
39
40
41
42
47
48
49
50
2
3
4
5
6
7
8
9
10
11
12
13
Pin No
LQFP LQFP
100
80
9
9
10
10
11
11
12
12
13
14
15
16
17
18
13
19
14
20
15
21
16
22
17
23
18
24
19
27
28
29
30
31
21
32
22
34
24
35
25
36
26
37
27
42
32
43
33
44
34
45
35
2
2
3
3
4
4
5
5
6
6
7
7
8
8
-
FBGA
121
E1
F4
F3
F2
F1
G1
G2
G3
G4
H1
H2
H3
H4
J1
J2
K2
L2
J3
J5
H5
K3
J4
L4
K4
K5
K6
J6
J7
J8
K8
C1
C2
D1
D2
D3
E2
E3
E4
F5
F6
G5
G6
Page 33 of 160
S6E2H4 Series
Pin
Function
GPIO
Pin Name
P60
P61
P62
P63
P64
P65
P66
P67
P68
P70
P71
P72
P73
P74
P80
P81
PE0
PE2
PE3
SIN0_0
SIN0_1
SOT0_0
(SDA0_0)
Multifunction
Serial 0
SOT0_1
(SDA0_1)
SCK0_0
(SCL0_0)
SCK0_1
(SCL0_1)
SIN1_0
SIN1_1
SOT1_0
(SDA1_0)
Multifunction
Serial 1
SOT1_1
(SDA1_1)
SCK1_0
(SCL1_0)
SCK1_1
(SCL1_1)
Function Description
LQFP
120
116
115
114
113
General-purpose I/O port 6
112
111
110
109
108
51
52
General-purpose I/O port 7
53
54
55
118
General-purpose I/O port 8
119
56
General-purpose I/O port E
58
59
88
Multi-function serial interface ch.0 input pin
65
Multi-function serial interface ch.0 output
pin.
This pin operates as SOT0 when it is used
in a UART/CSIO/LIN (operation modes 0 to
3) and as SDA0 when it is used in an I2C
(operation mode 4).
Multi-function serial interface ch.0 clock I/O
pin.
This pin operates as SCK0 when it is used
in a UART/CSIO/LIN (operation modes 0 to
3) and as SCL0 when it is used in an I2C
(operation mode 4).
Multi-function serial interface ch.1 input pin
Multi-function serial interface ch.1 output
pin.
This pin operates as SOT1 when it is used
in a UART/CSIO/LIN (operation modes 0 to
3) and as SDA1 when it is used in an I2C
(operation mode 4).
Multi-function serial interface ch.1 clock I/O
pin.
This pin operates as SCK1 when it is used
in a CSIO (operation modes 2) and as
SCL1 when it is used in an I2C (operation
mode 4).
Document Number: 001-98941 Rev.*C
Pin No
LQFP LQFP
100
80
96
76
95
75
94
74
93
73
98
78
99
79
46
36
48
38
49
39
73
59
55
44
FBGA
121
B2
B3
C3
B4
C4
D4
D5
E5
E6
H6
H7
G7
H8
J9
A3
A2
L8
L9
L10
C11
G10
87
72
58
C10
66
56
45
G9
86
71
57
D11
67
57
46
G8
96
62
81
52
66
41
A8
J10
97
82
67
D7
63
53
42
H10
98
83
-
C7
64
54
43
H9
Page 34 of 160
S6E2H4 Series
Pin No
Pin
Function
Multifunction
Serial 2
Pin Name
SIN2_0
SIN2_1
SIN2_2
SOT2_0
(SDA2_0)
SOT2_1
(SDA2_1)
SOT2_2
(SDA2_2)
SCK2_0
(SCL2_0)
SCK2_1
(SCL2_1)
SCK2_2
(SCL2_2)
SIN3_0
SIN3_1
SOT3_0
(SDA3_0)
Multifunction
Serial 3
SOT3_1
(SDA3_1)
SCK3_0
(SCL3_0)
SCK3_1
(SCL3_1)
Function Description
Multi-function serial interface ch.2 input pin
Multi-function serial interface ch.2 output
pin.
This pin operates as SOT2 when it is used
in a UART/CSIO/LIN (operation modes 0 to
3) and as SDA2 when it is used in an I2C
(operation mode 4).
Multi-function serial interface ch.2 clock I/O
pin.
This pin operates as SCK2 when it is used
in a CSIO (operation modes 2) and as
SCL2 when it is used in an I2C (operation
mode 4).
Multi-function serial interface ch.3 input pin
Multi-function serial interface ch.3 output
pin.
This pin operates as SOT3 when it is used
in a UART/CSIO/LIN (operation modes 0 to
3) and as SDA3 when it is used in an I2C
(operation mode 4).
Multi-function serial interface ch.3 clock I/O
pin.
This pin operates as SCK3 when it is used
in a CSIO (operation modes 2) and as
SCL3 when it is used in an I2C (operation
mode 4).
Document Number: 001-98941 Rev.*C
LQFP
120
LQFP
100
LQFP
80
FBGA
121
53
85
68
58
47
G7
B10
F10
54
-
-
H8
84
-
-
C9
69
59
48
F9
55
-
-
J9
83
-
-
D8
74
64
53
F8
110
15
10
10
D5
F4
109
-
-
E5
16
11
11
F3
108
-
-
E6
17
12
12
F2
Page 35 of 160
S6E2H4 Series
Pin
Function
Multifunction
Serial 4
Multifunction
Serial 5
Pin Name
SIN4_0
SIN4_1
SIN4_2
SOT4_0
(SDA4_0)
SOT4_1
(SDA4_1)
SOT4_2
(SDA4_2)
SCK4_0
(SCL4_0)
SCK4_1
(SCL4_1)
SCK4_2
(SCL4_2)
CTS4_0
CTS4_1
CTS4_2
RTS4_0
RTS4_1
RTS4_2
SIN5_0
SIN5_1
SIN5_2
SOT5_0
(SDA5_0)
SOT5_1
(SDA5_1)
SOT5_2
(SDA5_2)
SCK5_0
(SCL5_0)
SCK5_1
(SCL5_1)
SCK5_2
(SCL5_2)
Function Description
LQFP
120
6
Multi-function serial interface ch.4 input pin
75
10
Multi-function serial interface ch.4 output
5
pin.
This pin operates as SOT4 when it is used
76
in a UART/CSIO/LIN (operation modes 0 to
3) and as SDA4 when it is used in an I2C
11
(operation mode 4).
Multi-function serial interface ch.4 clock I/O
4
pin.
This pin operates as SCK4 when it is used
77
in a CSIO (operation modes 2) and as
SCL4 when it is used in an I2C (operation
12
mode 4).
2
Multi-function serial interface ch.4 CTS
78
input pin
13
3
Multi-function serial interface ch.4 RTS
79
output pin
14
114
Multi-function serial interface ch.5 input pin 113
20
Multi-function serial interface ch.5 output
115
pin.
This pin operates as SOT5 when it is used
112
in a UART/CSIO/LIN (operation modes 0 to
3) and as SDA5 when it is used in an I2C
21
(operation mode 4).
Multi-function serial interface ch.5 clock I/O
116
pin.
This pin operates as SCK5 when it is used
111
in a CSIO (operation modes 2) and as
SCL5 when it is used in an I2C (operation
22
mode 4).
Document Number: 001-98941 Rev.*C
Pin No
LQFP LQFP
100
80
6
6
65
54
-
FBGA
121
D3
E11
F5
5
5
D2
66
55
E10
-
-
F6
4
4
D1
67
56
E9
-
-
G5
2
68
3
69
9
94
15
2
3
9
74
-
C1
E8
G6
C2
D10
E1
C3
B4
G2
95
75
B3
-
-
C4
16
-
G3
96
76
B2
-
-
D4
17
-
G4
Page 36 of 160
S6E2H4 Series
Pin
Function
Pin Name
SIN6_0
SIN6_1
SOT6_0
(SDA6_0)
Multifunction
Serial 6
SOT6_1
(SDA6_1)
SCK6_0
(SCL6_0)
SCK6_1
(SCL6_1)
LQFP
120
7
Multi-function serial interface ch.6 input pin
95
Multi-function serial interface ch.6 output
pin.
This pin operates as SOT6 when it is used
in a UART/CSIO/LIN (operation modes 0 to
3) and as SDA6 when it is used in an I2C
(operation mode 4).
Multi-function serial interface ch.6 clock I/O
pin.
This pin operates as SCK6 when it is used
in a CSIO (operation modes 2) and as
SCL6 when it is used in an I2C (operation
mode 4).
Pin No
LQFP LQFP
100
80
7
7
80
65
FBGA
121
E2
B8
8
8
8
E3
94
79
64
C8
9
-
-
E4
93
78
63
A9
SCS6_1
Multi-function serial interface ch.6 serial
chip select pin
92
77
62
B9
SIN7_0
SIN7_1
Multi-function serial interface ch.7 input pin
101
50
86
45
35
D6
K8
100
85
-
A7
49
44
34
J8
99
84
-
B7
48
43
33
J7
47
42
32
J6
SOT7_0
(SDA7_0)
SOT7_1
(SDA7_1)
Multifunction
Serial 7
Function Description
SCK7_0
(SCL7_0)
SCK7_1
(SCL7_1)
SCS7_1
Multi-function serial interface ch.7 output
pin.
This pin operates as SOT7 when it is used
in a UART/CSIO/LIN (operation modes 0 to
3) and as SDA7 when it is used in an I2C
(operation mode 4).
Multi-function serial interface ch.7 clock I/O
pin.
This pin operates as SCK7 when it is used
in a CSIO (operation modes 2) and as
SCL7 when it is used in an I2C (operation
mode 4).
Multi-function serial interface ch.7 serial
chip select pin
Document Number: 001-98941 Rev.*C
Page 37 of 160
S6E2H4 Series
Pin
Function
Pin Name
DTTI0X_0
DTTI0X_1
Multifunction
Timer 0
FRCK0_0
FRCK0_1
FRCK0_2
IC00_0
IC00_1
IC00_2
IC01_0
IC01_1
IC01_2
IC02_0
IC02_1
IC02_2
IC03_0
IC03_1
IC03_2
RTO00_0
(PPG00_0)
RTO00_1
(PPG00_1)
RTO01_0
(PPG00_0)
RTO01_1
(PPG00_1)
RTO02_0
(PPG02_0)
RTO02_1
(PPG02_1)
RTO03_0
(PPG02_0)
RTO03_1
(PPG02_1)
RTO04_0
(PPG04_0)
RTO04_1
(PPG04_1)
RTO05_0
(PPG04_0)
RTO05_1
(PPG04_1)
Function Description
Input signal controlling wave form
generator outputs RTO00 to RTO05 of
Multi-function timer 0.
16-bit free-run timer ch.0 external clock
input pin
16-bit input capture ch.0 input pin of Multifunction timer 0.
ICxx describes channel number.
Wave form generator output pin of Multifunction timer 0.
This pin operates as PPG00 when it is
used in PPG0 output modes.
Wave form generator output pin of Multifunction timer 0.
This pin operates as PPG00 when it is
used in PPG0 output modes.
Wave form generator output pin of Multifunction timer 0.
This pin operates as PPG02 when it is
used in PPG0 output modes.
Wave form generator output pin of Multifunction timer 0.
This pin operates as PPG02 when it is
used in PPG0 output modes.
Wave form generator output pin of Multifunction timer 0.
This pin operates as PPG04 when it is
used in PPG0 output modes.
Wave form generator output pin of Multifunction timer 0.
This pin operates as PPG04 when it is
used in PPG0 output modes.
Document Number: 001-98941 Rev.*C
LQFP
120
Pin No
LQFP LQFP
100
80
FBGA
121
23
18
13
H1
79
69
-
D10
18
80
62
22
75
63
21
76
64
20
77
65
19
78
66
13
70
52
17
65
53
16
66
54
15
67
55
14
68
56
41
54
42
55
43
56
44
45
F1
D9
J10
G4
E11
H10
G3
E10
H9
G2
E9
G10
G1
E8
G9
24
19
14
H2
86
71
57
D11
25
20
15
H3
85
-
-
B10
26
21
16
H4
84
-
-
C9
27
22
17
J1
83
-
-
D8
28
23
18
J2
82
-
-
E7
29
24
19
K2
81
-
-
F7
Page 38 of 160
S6E2H4 Series
Pin Function
Pin Name
DTTI1X_0
Function Description
Pin No
LQFP LQFP
100
80
FBGA
121
8
8
8
E3
55
-
-
J9
96
81
66
A8
50
45
35
K8
IC10_0
95
80
65
B8
IC10_1
54
-
-
H8
IC11_0
94
79
64
C8
53
-
-
G7
93
78
63
A9
IC12_1
52
-
-
H7
IC13_0
92
77
62
B9
IC13_1
51
-
-
H6
2
2
2
C1
32
27
-
L2
3
3
3
C2
33
28
-
J3
4
4
4
D1
34
29
-
J5
5
5
5
D2
35
30
-
H5
6
6
6
D3
36
31
21
K3
7
7
7
E2
37
32
22
J4
DTTI1X_1
FRCK1_0
FRCK1_1
Input signal controlling wave form
generator outputs RTO10 to RTO15 of
Multi-function timer 1.
16-bit free-run timer ch.1 external clock
input pin
IC11_1
IC12_0
Multi- function
Timer 1
LQFP
120
RTO10_0
(PPG10_0)
RTO10_1
(PPG10_1)
RTO11_0
(PPG10_0)
RTO11_1
(PPG10_1)
RTO12_0
(PPG12_0)
RTO12_1
(PPG12_1)
RTO13_0
(PPG12_0)
RTO13_1
(PPG12_1)
RTO14_0
(PPG14_0)
RTO14_1
(PPG14_1)
16-bit input capture ch.1 input pin of Multifunction timer 1.
ICxx describes channel number.
Wave form generator output pin of Multifunction timer 1.
This pin operates as PPG10 when it is
used in PPG1 output modes.
Wave form generator output pin of Multifunction timer 1.
This pin operates as PPG10 when it is
used in PPG1 output modes.
Wave form generator output pin of Multifunction timer 1.
This pin operates as PPG12 when it is
used in PPG1 output modes.
Wave form generator output pin of Multifunction timer 1.
This pin operates as PPG12 when it is
used in PPG1 output modes.
Wave form generator output pin of Multifunction timer 1.
This pin operates as PPG14 when it is
used in PPG1 output modes.
RTO15_0 Wave form generator output pin of Multi(PPG14_0) function timer 1.
RTO15_1 This pin operates as PPG14 when it is
(PPG14_1) used in PPG1 output modes.
Document Number: 001-98941 Rev.*C
Page 39 of 160
S6E2H4 Series
Pin Function
Pin Name
Pin No
LQFP LQFP
100
80
FBGA
121
74
64
53
F8
DTTI2X_1
15
10
10
F4
FRCK2_0
FRCK2_1
16-bit free-run timer ch.2 external clock
input pin
116
101
96
86
76
-
B2
D6
IC20_0
IC20_1
119
100
99
85
79
-
A2
A7
IC21_0
IC21_1
118
16-bit input capture ch.2 input pin of Multi- 99
function timer 2.
114
ICxx describes channel number.
98
98
84
78
-
A3
B7
94
83
74
-
C3
C7
113
97
93
82
73
67
B4
D7
69
59
48
F9
IC22_0
IC22_1
Quadrature
Position/
Revolution
Counter 0
LQFP
120
Input signal controlling wave form
generator outputs RTO20 to RTO25 of
Multi-function timer 2.
DTTI2X_0
Multi- function
Timer 2
Function Description
IC23_0
IC23_1
RTO20_0
(PPG20_0)
RTO20_1
(PPG20_1)
RTO21_0
(PPG20_0)
RTO21_1
(PPG20_1)
RTO22_0
(PPG22_0)
RTO22_1
(PPG22_1)
RTO23_0
(PPG22_0)
RTO23_1
(PPG22_1)
RTO24_0
(PPG24_0)
RTO24_1
(PPG24_1)
RTO25_0
(PPG24_0)
RTO25_1
(PPG24_1)
AIN0_0
AIN0_1
AIN0_2
BIN0_0
BIN0_1
BIN0_2
ZIN0_0
ZIN0_1
ZIN0_2
Wave form generator output pin of Multifunction timer 2.
This pin operates as PPG10 when it is
used in PPG2 output modes.
Wave form generator output pin of Multifunction timer 2.
This pin operates as PPG20 when it is
used in PPG2 output modes.
Wave form generator output pin of Multifunction timer 2.
This pin operates as PPG22 when it is
used in PPG2 output modes.
Wave form generator output pin of Multifunction timer 2.
This pin operates as PPG22 when it is
used in PPG2 output modes.
Wave form generator output pin of Multifunction timer 2.
This pin operates as PPG24 when it is
used in PPG2 output modes.
Wave form generator output pin of Multifunction timer 2.
This pin operates as PPG24 when it is
used in PPG2 output modes.
QPRC ch.0 AIN input pin
QPRC ch.0 BIN input pin
QPRC ch.0 ZIN input pin
Document Number: 001-98941 Rev.*C
9
-
68
58
10
-
67
57
11
-
72
12
-
88
73
13
-
89
74
14
9
24
51
2
25
52
3
26
53
4
-
G6
-
B11
E1
9
19
2
20
3
21
4
G5
C11
59
-
F6
C10
58
-
F5
G8
46
-
87
F10
47
-
E4
14
2
15
3
16
4
H2
H6
C1
H3
H7
C2
H4
G7
D1
Page 40 of 160
S6E2H4 Series
Pin Function
Quadrature
Position/
Revolution
Counter 1
Pin Name
AIN1_0
AIN1_1
AIN1_2
BIN1_0
BIN1_1
BIN1_2
ZIN1_0
ZIN1_1
ZIN1_2
AIN2_0
AIN2_1
AIN2_2
Quadrature
Position/
Revolution
Counter 2
Real-time
clock
BIN2_0
BIN2_1
Function Description
QPRC ch.1 AIN input pin
QPRC ch.1 BIN input pin
QPRC ch.1 ZIN input pin
QPRC ch.2 AIN input pin
QPRC ch.2 BIN input pin
BIN2_2
ZIN2_0
ZIN2_1
ZIN2_2
RTCCO_0
RTCCO_1
RTCCO_2
SUBOUT_0
SUBOUT_1
SUBOUT_2
QPRC ch.2 ZIN input pin
0.5 seconds pulse output pin of Real-time
clock
Sub clock output pin
Deep standby mode return signal input pin
0
Deep standby mode return signal input pin
WKUP1
1
Deep standby mode return signal input pin
WKUP2
2
Deep standby mode return signal input pin
WKUP3
3
DA0
D/A converter ch.0 analog output pin
DA1
D/A converter ch.1 analog output pin
VREGCTL On-board regulator control pin
The return signal input pin from a
VWAKEUP
hibernation state
TX0_0
TX0_1
CAN interface ch.0 TX output pin
TX0_2
RX0_0
RX0_1
CAN interface ch.0 RX input pin
RX0_2
TX1_0
TX1_1
CAN interface ch.1 TX output pin
TX1_2
RX1_0
RX1_1
CAN interface ch.1 RX input pin
RX1_2
WKUP0
Low-Power
Consumption
Mode
DAC
VBAT
CAN0
CAN1
Document Number: 001-98941 Rev.*C
Pin No
LQFP LQFP LQFP
120
100
80
10
89
74
48
43
33
11
88
73
49
44
34
12
87
72
50
45
35
33
28
-
FBGA
121
F5
B11
J7
F6
C11
J8
G5
C10
K8
J3
119
69
99
59
79
48
A2
F9
34
118
29
98
78
J5
A3
68
35
58
30
47
-
F10
H5
115
67
115
64
23
115
64
23
95
57
75
46
95
54
18
95
54
18
75
43
13
75
43
13
B3
G8
B3
H9
H1
B3
H9
H1
116
96
76
B2
14
9
9
E1
50
45
35
K8
69
59
48
F9
36
37
41
31
32
36
21
22
26
K3
J4
K5
42
37
27
K6
51
18
114
52
19
113
84
12
63
85
11
62
13
94
14
93
53
52
74
73
42
41
H6
F1
C3
H7
G1
B4
C9
G5
H10
B10
F6
J10
Page 41 of 160
S6E2H4 Series
Pin Function
Pin Name
Reset
INITX
MD1
Mode
MD0
Function Description
External Reset Input pin.
A reset is valid when INITX=L.
Mode 1 pin.
During serial programming to Flash
memory, MD1=L must be input.
Mode 0 pin.
During normal operation, MD0=L must be
input. During serial programming to Flash
memory, MD0=H must be input.
Power
VCC
Power supply Pin
GND
VSS
GND Pin
Clock
X0
X1
X0A
X1A
CROUT_0
CROUT_1
AVCC
ADC
Power
AVRL
AVRH
VBAT
Power
ADC
GND
C pin
VBAT
AVSS
C
Main clock (oscillation) input pin
Main clock (oscillation) I/O pin
Sub clock (oscillation) input pin
Sub clock (oscillation) I/O pin
Built-in high-speed CR-osc clock output
port
A/D converter and D/A converter
analog power supply pin
A/D converter analog reference voltage
input pin
A/D converter analog reference voltage
input pin
VBAT power supply pin.
Backup power supply (battery etc.) and
system power supply.
A/D converter and D/A converter
GND pin
Power supply stabilization capacity pin
LQFP
120
Pin No
LQFP LQFP
100
80
FBGA
121
38
33
23
L3
56
46
36
L8
57
47
37
K9
1
31
46
61
91
117
107
30
45
60
90
120
1
26
41
51
76
97
92
25
40
50
75
100
1
31
61
77
20
30
40
60
80
B1
K1
K7
K11
A10
A4
A6
L1
L7
L11
A11
A1
-
-
-
K10
58
59
39
40
87
113
48
49
34
35
72
93
38
39
24
25
58
73
L9
L10
L4
K4
C10
B4
70
60
49
J11
72
62
51
G11
73
63
52
F11
43
38
28
L5
71
61
50
H11
44
39
29
L6
Notes:
−
While this device contains a Test Access Port (TAP) based on the IEEE 1149.1-2001 JTAG standard, it is not fully compliant
to all requirements of that standard. This device may contain a 32-bit device ID that is the same as the 32-bit device ID in
other devices with different functionality. The TAP pins may also be configurable for purposes other than access to the TAP
controller.
Document Number: 001-98941 Rev.*C
Page 42 of 160
S6E2H4 Series
5. I/O Circuit Type
Type
Circuit
P-ch
P-ch
Remarks
Digital output
X1
N-ch
Digital output
R
It is possible to select the main
oscillation / GPIO function
Pull-up resistor control
Digital input
When the main oscillation is
selected.
−
Clock input
Oscillation feedback resistor
: Approximately 1MΩ
Standby mode control
−
With Standby mode control
When the GPIO is selected.
A
−
CMOS level output.
−
CMOS level hysteresis input
−
With pull-up resistor control
−
With standby mode control
Digital input
−
Pull-up resistor
Standby mode control
−
IOH = -4 mA, IOL = 4 mA
−
CMOS level hysteresis input
−
Pull-up resistor
Standby mode control
: Approximately 50 kΩ
R
P-ch
P-ch
Digital output
N-ch
Digital output
X0
Pull-up resistor control
B
Pull-up resistor
: Approximately 50 kΩ
Digital input
Document Number: 001-98941 Rev.*C
Page 43 of 160
S6E2H4 Series
Type
Circuit
Remarks
Digital input
C
Digital output
N-ch
P-ch
P-ch
Digital output
E
N-ch
−
Open drain output
−
CMOS level hysteresis input
−
CMOS level output
−
CMOS level hysteresis input
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
: Approximately 50 kΩ
Digital output
R
−
IOH = -4 mA, IOL = 4 mA
−
When this pin is used as an I2C pin,
the digital output P-ch transistor is
Pull-up resistor control
always off.
Digital input
Standby mode control
P-ch
P-ch
N-ch
Digital output
Digital output
F
−
CMOS level output
−
CMOS level hysteresis input
−
With input control
−
Analog input
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
: Approximately 50 kΩ
Pull-up resistor control
R
Digital input
Standby mode control
−
IOH = -4 mA, IOL = 4 mA
−
When this pin is used as an I2C pin,
the digital output P-ch transistor is
always off.
Analog input
Input control
Document Number: 001-98941 Rev.*C
Page 44 of 160
S6E2H4 Series
Type
Circuit
P-ch
G
P-ch
N-ch
Remarks
Digital output
−
CMOS level output
−
CMOS level hysteresis input
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
Digital output
R
: Approximately 50 kΩ
−
IOH = -12 mA, IOL = 12 mA
−
When this pin is used as an I2C pin,
the digital output P-ch transistor is
Pull-up resistor
control
Digital input
always off.
Standby mode
control
P-ch
P-ch
Digital output
I
N-ch
Digital output
−
CMOS level output
−
CMOS level hysteresis input
−
5V tolerant
−
With standby mode control
−
Pull-up resistor
: Approximately 50 kΩ
R
−
IOH = -4 mA, IOL = 4 mA
−
Available to control of PZR registers.
Pull-up resistor
control
Digital input
Standby mode control
J
Document Number: 001-98941 Rev.*C
Mode input
CMOS level hysteresis input
Page 45 of 160
S6E2H4 Series
Type
Circuit
P-ch
L
P-ch
N-ch
Remarks
Digital output
−
CMOS level output
−
CMOS level hysteresis input
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
Digital output
: Approximately 50 kΩ
−
IOH = -8 mA, IOL = 8 mA
−
When this pin is used as an I2C pin,
the digital output P-ch transistor is
Pull-up resistor
control
Digital input
R
always off.
Standby mode
control
P-ch
P-ch
N-ch
Digital output
Digital output
M
R
Pull-up resistor
control
Digital input
−
CMOS level output
−
CMOS level hysteresis input
−
With input control
−
Analog input
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
: Approximately 50 kΩ
−
IOH = -8 mA, IOL = 8 mA
Standby mode
control
Analog input
Input control
Document Number: 001-98941 Rev.*C
Page 46 of 160
S6E2H4 Series
Type
Circuit
P-ch
P-ch
Remarks
Digital output
−
CMOS level output
−
CMOS level hysteresis input
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
: Approximately 50 kΩ
−
N
N-ch
Digital output
IOH = -4 mA, IOL = 4 mA
(GPIO)
−
IOL = 20 mA
(Fast Mode Plus)
−
Pull-up resistor
control
Digital input
R
When this pin is used as an I2C pin,
the digital output P-ch transistor is
always off.
Standby mode
control
P-ch
P-ch
O
N-ch
Pull-up resistor
control
Digital output
Digital output
−
CMOS level output
−
CMOS level hysteresis input
−
5 V tolerant
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
: Approximately 50 kΩ
−
IOH = -4 mA, IOL = 4 mA
−
For I/O setting, refer to VBAT Domain
in the Peripheral Manual
R
Digital input
Standby mode
control
Document Number: 001-98941 Rev.*C
Page 47 of 160
S6E2H4 Series
Type
Circuit
P-ch
P-ch
X0A
N-ch
P
Remarks
Pull-up resistor
control
Digital output
Digital output
−
CMOS level output
−
CMOS level hysteresis input
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
: Approximately 50 kΩ
−
IOH = -4 mA, IOL = 4 mA
−
For I/O setting, refer to VBAT Domain
in the Peripheral Manual
R
Digital input
Standby mode
control
OSC
P-ch
P-ch
X1A
Pull-up resistor
control
Digital output
It is possible to select the sub
oscillation / GPIO function
When the sub oscillation is
selected.
−
Oscillation feedback resistor
: Approximately 10 MΩ
N-ch
Digital output
Q
R
Digital input
Standby mode
control
OSC
RX
−
With Standby mode control
−
When the GPIO is selected.
−
CMOS level output.
−
CMOS level hysteresis input
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
: Approximately 50 kΩ
−
IOH = -4 mA, IOL = 4 mA
−
For I/O setting, refer to VBAT Domain
in the Peripheral Manual
Standby mode
control
Clock input
Document Number: 001-98941 Rev.*C
Page 48 of 160
S6E2H4 Series
Type
Circuit
P-ch
P-ch
N-ch
Remarks
Pull-up resistor
control
Digital output
Digital output
R
−
CMOS level output
−
CMOS level hysteresis input
−
Analog output
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
: Approximately 50 kΩ
−
IOH = -12 mA, IOL = 12 mA
(4.5 V to 5.5 V)
R
−
Digital input
IOH = -8 mA, IOL = 8 mA
(2.7 V to 4.5 V)
Standby mode
control
Analog output
Document Number: 001-98941 Rev.*C
Page 49 of 160
S6E2H4 Series
6. Handling Precautions
Any semiconductor devices have inherently a certain rate of failure. The possibility of failure is greatly affected by the conditions in
which they are used (circuit conditions, environmental conditions, etc.). This page describes precautions that must be observed to
minimize the chance of failure and to obtain higher reliability from your Cypress semiconductor devices.
6.1
Precautions for Product Design
This section describes precautions when designing electronic equipment using semiconductor devices.
Absolute Maximum Ratings
Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of
certain established limits, called absolute maximum ratings. Do not exceed these ratings.
Recommended Operating Conditions
Recommended operating conditions are normal operating ranges for the semiconductor device. All the device's electrical
characteristics are warranted when operated within these ranges.
Always use semiconductor devices within the recommended operating conditions. Operation outside these ranges may adversely
affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users
considering application outside the listed conditions are advised to contact their sales representative beforehand.
Processing and Protection of Pins
These precautions must be followed when handling the pins which connect semiconductor devices to power supply and
input/output functions.
(1) Preventing Over-Voltage and Over-Current Conditions
Exposure to voltage or current levels in excess of maximum ratings at any pin is likely to cause deterioration within the device,
and in extreme cases leads to permanent damage of the device. Try to prevent such overvoltage or over-current conditions at
the design stage.
(2) Protection of Output Pins
Shorting of output pins to supply pins or other output pins, or connection to large capacitance can cause large current flows.
Such conditions if present for extended periods of time can damage the device.
Therefore, avoid this type of connection.
(3) Handling of Unused Input Pins
Unconnected input pins with very high impedance levels can adversely affect stability of operation. Such pins should be
connected through an appropriate resistance to a power supply pin or ground pin.
Code: DS00-00004-3E
Document Number: 001-98941 Rev.*C
Page 50 of 160
S6E2H4 Series
Latch-up
Semiconductor devices are constructed by the formation of P-type and N-type areas on a substrate. When subjected to abnormally
high voltages, internal parasitic PNPN junctions (called thyristor structures) may be formed, causing large current levels in excess
of several hundred mA to flow continuously at the power supply pin. This condition is called latch-up.
CAUTION: The occurrence of latch-up not only causes loss of reliability in the semiconductor device, but can cause injury or
damage from high heat, smoke or flame. To prevent this from happening, do the following:
(1) Be sure that voltages applied to pins do not exceed the absolute maximum ratings. This should include attention to abnormal
noise, surge levels, etc.
(2) Be sure that abnormal current flows do not occur during the power-on sequence.
Observance of Safety Regulations and Standards
Most countries in the world have established standards and regulations regarding safety, protection from electromagnetic
interference, etc. Customers are requested to observe applicable regulations and standards in the design of products.
Fail-Safe Design
Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such
failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and
prevention of over-current levels and other abnormal operating conditions.
Precautions Related to Usage of Devices
Cypress semiconductor devices are intended for use in standard applications (computers, office automation and other office
equipment, industrial, communications, and measurement equipment, personal or household devices, etc.).
CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly
affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as
aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.)
are requested to consult with sales representatives before such use. The company will not be responsible for damages arising
from such use without prior approval.
6.2
Precautions for Package Mounting
Package mounting may be either lead insertion type or surface mount type. In either case, for heat resistance during soldering, you
should only mount under Cypress's recommended conditions. For detailed information about mount conditions, contact your sales
representative.
Lead Insertion Type
Mounting of lead insertion type packages onto printed circuit boards may be done by two methods: direct soldering on the board,
or mounting by using a socket.
Direct mounting onto boards normally involves processes for inserting leads into through-holes on the board and using the flow
soldering (wave soldering) method of applying liquid solder. In this case, the soldering process usually causes leads to be
subjected to thermal stress in excess of the absolute ratings for storage temperature. Mounting processes should conform to
Cypress recommended mounting conditions.
If socket mounting is used, differences in surface treatment of the socket contacts and IC lead surfaces can lead to contact
deterioration after long periods. For this reason it is recommended that the surface treatment of socket contacts and IC leads be
verified before mounting.
Surface Mount Type
Surface mount packaging has longer and thinner leads than lead-insertion packaging, and therefore leads are more easily
deformed or bent. The use of packages with higher pin counts and narrower pin pitch results in increased susceptibility to open
connections caused by deformed pins, or shorting due to solder bridges.
You must use appropriate mounting techniques. Cypress recommends the solder reflow method, and has established a ranking of
mounting conditions for each product. Users are advised to mount packages in accordance with Cypress ranking of recommended
conditions.
Document Number: 001-98941 Rev.*C
Page 51 of 160
S6E2H4 Series
Lead-Free Packaging
CAUTION: When ball grid array (FBGA) packages with Sn-Ag-Cu balls are mounted using Sn-Pb eutectic soldering, junction
strength may be reduced under some conditions of use.
Storage of Semiconductor Devices
Because plastic chip packages are formed from plastic resins, exposure to natural environmental conditions will cause absorption
of moisture. During mounting, the application of heat to a package that has absorbed moisture can cause surfaces to peel,
reducing moisture resistance and causing packages to crack. To prevent, do the following:
(1) Avoid exposure to rapid temperature changes, which cause moisture to condense inside the product. Store products in
locations where temperature changes are slight.
(2) Use dry boxes for product storage. Products should be stored below 70% relative humidity, and at temperatures between 5°C
and 30°C.
When you open Dry Package that recommends humidity 40% to 70% relative humidity.
(3) When necessary, Cypress packages semiconductor devices in highly moisture-resistant aluminum laminate bags, with a silica
gel desiccant. Devices should be sealed in their aluminum laminate bags for storage.
(4) Avoid storing packages where they are exposed to corrosive gases or high levels of dust.
Baking
Packages that have absorbed moisture may be de-moisturized by baking (heat drying). Follow the Cypress recommended
conditions for baking.
Condition: 125°C/24 h
Static Electricity
Because semiconductor devices are particularly susceptible to damage by static electricity, you must take the following
precautions:
(1) Maintain relative humidity in the working environment between 40% and 70%. Use of an apparatus for ion generation may be
needed to remove electricity.
(2) Electrically ground all conveyors, solder vessels, soldering irons and peripheral equipment.
(3) Eliminate static body electricity by the use of rings or bracelets connected to ground through high resistance (on the level of 1
MΩ).
Wearing of conductive clothing and shoes, use of conductive floor mats and other measures to minimize shock loads is
recommended.
(4) Ground all fixtures and instruments, or protect with anti-static measures.
(5) Avoid the use of styrofoam or other highly static-prone materials for storage of completed board assemblies.
Document Number: 001-98941 Rev.*C
Page 52 of 160
S6E2H4 Series
6.3
Precautions for Use Environment
Reliability of semiconductor devices depends on ambient temperature and other conditions as described above.
For reliable performance, do the following:
(1) Humidity
Prolonged use in high humidity can lead to leakage in devices as well as printed circuit boards. If high humidity levels are
anticipated, consider anti-humidity processing.
(2) Discharge of Static Electricity
When high-voltage charges exist close to semiconductor devices, discharges can cause abnormal operation. In such cases,
use anti-static measures or processing to prevent discharges.
(3) Corrosive Gases, Dust, or Oil
Exposure to corrosive gases or contact with dust or oil may lead to chemical reactions that will adversely affect the device. If
you use devices in such conditions, consider ways to prevent such exposure or to protect the devices.
(4) Radiation, Including Cosmic Radiation
Most devices are not designed for environments involving exposure to radiation or cosmic radiation. Users should provide
shielding as appropriate.
(5) Smoke, Flame
CAUTION: Plastic molded devices are flammable, and therefore should not be used near combustible substances. If devices
begin to smoke or burn, there is danger of the release of toxic gases.
Customers considering the use of Cypress products in other special environmental conditions should consult with sales
representatives.
Please check the latest handling precautions at the following URL.
http://www.spansion.com/fjdocuments/fj/datasheet/e-ds/DS00-00004.pdf
Document Number: 001-98941 Rev.*C
Page 53 of 160
S6E2H4 Series
7. Handling Devices
Power Supply Pins
In products with multiple VCC and VSS pins, respective pins at the same potential are interconnected within the device in order to
prevent malfunctions such as latch-up. However, all of these pins should be connected externally to the power supply or ground
lines in order to reduce electromagnetic emission levels, to prevent abnormal operation of strobe signals caused by the rise in the
ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with each POWER pins and GND pins of this device at low impedance. It is also
advisable that a ceramic capacitor of approximately 0.1 µF be connected as a bypass capacitor between VCC and VSS near this
device.
Power Supply Pins
A malfunction may occur when the power supply voltage fluctuates rapidly even though the fluctuation is within the guaranteed
operating range of the VCC power supply voltage. As a rule of voltage stabilization, suppress voltage fluctuation so that the
fluctuation in VCC ripple (peak-to-peak value) at the commercial frequency (50 Hz/60 Hz) does not exceed 10% of the standard
VCC value, and the transient fluctuation rate does not exceed 0.1 V/μs at a momentary fluctuation such as switching the power
supply.
Crystal Oscillator Circuit
Noise near the X0/X1 and X0A/X1A pins may cause the device to malfunction. Design the printed circuit board so that X0/X1,
X0A/X1A pins, the crystal oscillator (or ceramic oscillator), and the bypass capacitor to ground are located as close to the device as
possible.
It is strongly recommended that the PC board artwork be designed such that the X0/X1 and X0A/X1A pins are surrounded by
ground plane as this is expected to produce stable operation.
Evaluate oscillation of your using crystal oscillator by your mount board.
Sub Crystal Oscillator
This series sub oscillator circuit is low gain to keep the low current consumption.
The crystal oscillator to fill the following conditions is recommended for sub crystal oscillator to stabilize the oscillation.
Surface mount type
Size:
More than 3.2 mm × 1.5 mm
Load capacitance: Approximately 6 pF to 7 pF
Lead type
Load capacitance: Approximately 6 pF to 7 pF
Document Number: 001-98941 Rev.*C
Page 54 of 160
S6E2H4 Series
Using an External Clock
When using an external clock as an input of the main clock, set X0/X1 to the external clock input, and input the clock to X0.
X1(PE3) can be used as a general-purpose I/O port.
Similarly, when using an external clock as an input of the sub clock, set X0A/X1A to the external clock input, and input the clock to
X0A. X1A (P47) can be used as a general-purpose I/O port.
Example of Using an External Clock
Device
X0(X0A)
Set as External clock
input
Can be used as
general-purpose
I/O ports.
X1(PE3), X1A (P47)
Handling when Using Multi-function Serial Pin as I2C Pin
If it is using the multi-function serial pin as I2C pins, P-ch transistor of digital output is always disabled.
However, I2C pins need to keep the electrical characteristic like other pins and not to connect to the external I 2C bus system with
power OFF.
C Pin
This series contains the regulator. Be sure to connect a smoothing capacitor (C S) for the regulator between the C pin and the GND
pin. Please use a ceramic capacitor or a capacitor of equivalent frequency characteristics as a smoothing capacitor.
However, some laminated ceramic capacitors have the characteristics of capacitance variation due to thermal fluctuation (F
characteristics and Y5V characteristics). Please select the capacitor that meets the specifications in the operating conditions to use
by evaluating the temperature characteristics of a capacitor.
A smoothing capacitor of about 4.7 μF would be recommended for this series.
C
Device
CS
VSS
GND
Mode Pins (MD0)
Connect the MD pin (MD0) directly to VCC or VSS pins. Design the printed circuit board such that the pull-up/down resistance
stays low, as well as the distance between the mode pins and VCC pins or VSS pins is as short as possible and the connection
impedance is low, when the pins are pulled-up/down such as for switching the pin level and rewriting the Flash memory data. It is
because of preventing the device erroneously switching to test mode due to noise.
Document Number: 001-98941 Rev.*C
Page 55 of 160
S6E2H4 Series
Notes on Power-on
Turn power on/off in the following order or at the same time.
If not using the A/D converter and D/A converter, connect AVCC = VCC and AVSS = VSS.
Turning on:
Turning off:
VBAT → VCC
VCC → AVCC → AVRH
VCC → VBAT
AVRH → AVCC → VCC
Serial Communication
There is a possibility to receive wrong data due to the noise or other causes on the serial communication.
Therefore, design a printed circuit board so as to avoid noise.
Consider the case of receiving wrong data due to noise, perform error detection such as by applying a checksum of data at the
end. If an error is detected, retransmit the data.
Differences in Features among the Products with Different Memory Sizes and between Flash Products and
MASK Products
The electric characteristics including power consumption, ESD, latch-up, noise characteristics, and oscillation characteristics
among the products with different memory sizes and between Flash products and MASK products are different because chip
layout and memory structures are different.
If you are switching to use a different product of the same series, please make sure to evaluate the electric characteristics.
Pull-Up Function of 5 V Tolerant I/O
Please do not input the signal more than VCC voltage at the time of Pull-Up function use of 5 V tolerant I/O.
Adjoining Wiring on Circuit Board
If wiring of the crystal oscillation circuit X1A adjoins and also runs in parallel with the wiring of P48/VREGCTL, there is a possibility
that the oscillation erroneously counts because X1A has noise with the change of P48/VREGCTL. Keep as much distance as
possible between both wirings and insert the ground pattern between them in order to avoid this possibility.
Device
P46/
X0A
P47/
X1A
P48/
P49/
VREGCTL VWAKEUP
Not allowed to run
both wirings in parallel
Ground
Insert the ground pattern
Handling when Using Debug Pins
When debug pins(TDO/TMS/TDI/TCK/TRSTX or SWO/SWDIO/SWCLK) are set to GPIO or other peripheral functions, only set
them as output, do not set them as input.
Document Number: 001-98941 Rev.*C
Page 56 of 160
S6E2H4 Series
8. Block Diagram
S6E2H44E/F/G, S6E2H46E/F/G
TRSTX,TCK,
TDI,TMS
TDO
TRACEDx,
TRACECLK
SWJ-DP
ETM*
TPIU*
ROM
Table
SRAM0
16/32 Kbytes
SRAM1
8/16 Kbytes
Cortex-M4 Core I
@160 MHz(Max)
D
MPU NVIC
Multi-layer AHB (Max 160 MHz)
FPU
Sys
AHB-APB Bridge:
APB0(Max 80 MHz)
Dual-Timer
Watchdog Timer
(Software)
Clock Reset
Generator
INITX
Watchdog Timer
(Hardware)
CSV
SRAM2
8/16 Kbytes
MainFlash I/F
Trace Buffer
(16 Kbytes)
Security
WorkFlash I/F
MainFlash
512 Kbytes/
256 Kbytes
WorkFlash
32 Kbytes
DMAC
8ch.
CLK
DSTC
CAN
X0A
X1A
Main
Osc
PLL
VBAT Domain
Sub
Osc
AHB-AHB Bridge
Source Clock
X0
X1
CR
100 kHz
CR
4 MHz
CAN
GPIO
PIN-Function-Ctrl
CROUT
TX0,
RX0
TX1,
RX1
P0x,
P1x,
.
.
.
PEx
MADx
ADTGx
TIOAx
TIOBx
AINx
BINx
ZINx
Unit 1
FRCK0
CAN Prescaler
Power-On
Reset
Base Timer
16-bit 16ch./
32-bit 8ch.
QPRC
3ch.
16-bit Input Capture
4ch.
16-bit Free-run Timer
3ch.
16-bit Output Compare
6ch.
DTTI0X
RTO0x
MCSXx,MDQMx,
MOEX,MWEX,
MALE,MRDY,
MNALE,MNCLE,
MNWEX,MNREX,
MCLKOUT,MSDWEX,
MSDCLK,MSDCKE,
MRASX,MCASX
Unit 2
A/D Activation Compare
6ch.
IC0x
MADATAx
12-bit A/D Converter
Unit 0
AHB-APB Bridge : APB2 (Max 80 MHz)
ANxx
External Bus I/F
AHB-APB Bridge : APB1 (Max 160 MHz)
AVCC,
AVSS,
AVRH
Waveform Generator
3ch.
16-bit PPG
3ch.
Multi-function Timer × 3
LVD Ctrl
LVD
IRQ-Monitor
Regulator
C
CRC Accelerator
Watch Counter
Deep Standby Ctrl
WKUPx
Peripheral Clock Gating
Low-speed CR Prescaler
VBAT Domain
Real-Time Clock
Port Ctrl.
VWAKEUP
VREGCTL
RTCCO,
SUBOUT
External Interrupt
Controller
16pin + NMI
INTx
NMIX
MODE-Ctrl
MD0,
MD1
Multi-function Serial I/F
8ch.
HW flow control(ch.4)
SCKx
SINx
SOTx
CTS4
RTS4
12-bit D/A Converter
2units
DAx
*: For the S6E2H44E0A and S6E2H46E0A, ETM is not available.
Document Number: 001-98941 Rev.*C
Page 57 of 160
S6E2H4 Series
9. Memory Size
See Memory size in 1. Product Lineup to confirm the memory size.
10. Memory Map
Memory Map (1)
Peripherals Area
0x41FF_FFFF
Reserved
0x4007_0000
0x4006_F000
GPIO
Reserved
0xFFFF_FFFF
Reserved
0xE010_0000
0xE000_0000
0xD000_0000
Cortex-M4 Private
Peripherals
Reg. Area
0x4006_3000
0x4006_2000
0x4006_1000
0x4006_0000
External Device
Area
0x4004_0000
0x4003_F000
CAN ch.1
CAN ch.0
DSTC
DMAC
Reserved
EXT-bus I/F
0x6000_0000
Reserved
Reserved
0x4400_0000
0x4200_0000
0x4003_C800
32 Mbytes
Bit band alias
0x4003_C100
0x4003_B000
Peripherals
0x4000_0000
0x4003_A000
0x4003_9000
0x4003_8000
Reserved
0x2400_0000
0x2200_0000
Reserved
0x2010_0000
0x200E_0000
0x200C_0000
0x2004_4000
See "Memory Map(2)" for the
memory size details.
0x2004_0000
0x2003_C000
0x2000_0000
0x1FFF_8000
0x0050_0000
0x0040_0000
Work Flash I/F
Work Flash
Reserved
SRAM2
SRAM1
Reserved
SRAM0
Reserved
Security/CR Trim
MainFlash
0x0000_0000
0x4003_7000
0x4003_6000
32 Mbytes
Bit band alias
0x4003_5000
RTC/Port Ctrl
Watch Counter
CRC
MFS
CAN prescaler
Reserved
LVD/DS mode
0x4003_4000
0x4003_3000
0x4003_2000
Reserved
0x4003_1000
Int-Req.Read
EXTI
Reserved
CR Trim
0x4003_0000
0x4002_F000
0x4002_E000
Reserved
0x4002_8000
0x4002_7000
0x4002_6000
0x4002_5000
0x4002_4000
0x4002_3000
0x4002_2000
0x4002_1000
0x4002_0000
0x4001_6000
0x4001_5000
0x4001_3000
0x4001_2000
0x4001_1000
0x4001_0000
0x4000_1000
0x4000_0000
Document Number: 001-98941 Rev.*C
Peripheral Clock Gating
0x4003_C000 Low Speed CR Prescaler
A/DC
QPRC
Base Timer
PPG
Reserved
MFT Unit2
MFT Unit1
MFT Unit0
Reserved
Dual Timer
Reserved
SW WDT
HW WDT
Clock/Reset
Reserved
MainFlash I/F
Page 58 of 160
S6E2H4 Series
Memory Map (2)
S6E2H46E0A
S6E2H46F0A
S6E2H46G0A
0x2020_0000
S6E2H44E0A
S6E2H44F0A
S6E2H44G0A
0x2020_0000
Reserved
0x200C_8000
0x200C_0000
Reserved
0x200C_8000
Work Flash
32Kbytes
0x200C_0000
Work Flash
32Kbytes
Reserved
Reserved
0x2004_4000
SRAM2
16 Kbytes
0x2004_0000
0x2004_2000
0x2004_0000
SRAM1
16 Kbytes
0x2003_E000
SRAM2
8 Kbytes
SRAM1
8 Kbytes
0x2003_C000
Reserved
Reserved
0x2000_0000
0x2000_0000
SRAM0
32 Kbytes
0x1FFF_C000
SRAM0
16 Kbytes
0x1FFF_8000
Reserved
Reserved
0x0040_6000
0x0040_6000
0x0040_4000
General purpose
0x0040_4000
General purpose
0x0040_2000
CR trimming
Security
0x0040_2000
CR trimming
Security
0x0040_0000
0x0040_0000
Reserved
0x0008_0000
Reserved
MainFlash
512 Kbytes
0x0004_0000
MainFlash
256 Kbytes
0x0000_0000
Document Number: 001-98941 Rev.*C
0x0000_0000
Page 59 of 160
S6E2H4 Series
Peripheral Address Map
Start address
0x4000_0000
0x4000_1000
0x4001_0000
0x4001_1000
0x4001_2000
0x4001_3000
0x4001_5000
0x4001_6000
0x4002_0000
0x4002_1000
0x4002_2000
0x4002_3000
0x4002_4000
0x4002_5000
0x4002_6000
0x4002_7000
0x4002_8000
0x4002_E000
0x4002_F000
0x4003_0000
0x4003_1000
0x4003_2000
0x4003_3000
0x4003_4000
0x4003_5000
0x4003_5800
0x4003_6000
0x4003_7000
0x4003_8000
0x4003_9000
0x4003_A000
0x4003_B000
0x4003_C000
0x4003_C100
0x4003_C800
0x4003_F000
0x4004_0000
0x4006_0000
0x4006_1000
0x4006_2000
0x4006_3000
0x4006_4000
0x4006_F000
0x4006_7000
0x200E_0000
Document Number: 001-98941 Rev.*C
End address
0x4000_0FFF
0x4000_FFFF
0x4001_0FFF
0x4001_1FFF
0x4001_2FFF
0x4001_4FFF
0x4001_5FFF
0x4001_FFFF
0x4002_0FFF
0x4002_1FFF
0x4002_2FFF
0x4003_FFFF
0x4002_4FFF
0x4002_5FFF
0x4002_6FFF
0x4002_7FFF
0x4002_DFFF
0x4002_EFFF
0x4002_FFFF
0x4003_0FFF
0x4003_1FFF
0x4003_4FFF
0x4003_3FFF
0x4003_4FFF
0x4003_57FF
0x4003_5FFF
0x4003_6FFF
0x4003_7FFF
0x4003_8FFF
0x4003_9FFF
0x4003_AFFF
0x4003_BFFF
0x4003_C0FF
0x4003_C7FF
0x4003_EFFF
0x4003_FFFF
0x4005_FFFF
0x4006_0FFF
0x4006_1FFF
0x4006_2FFF
0x4006_3FFF
0x4006_EFFF
0x4006_FFFF
0x41FF_FFFF
0x200E_FFFF
Bus
AHB
APB0
APB1
APB2
AHB
Peripherals
MainFlash I/F register
Reserved
Clock/Reset Control
Hardware Watchdog timer
Software Watchdog timer
Reserved
Dual-Timer
Reserved
Multi-function timer unit0
Multi-function timer unit1
Multi-function timer unit2
Reserved
PPG
Base Timer
Quadrature Position/Revolution Counter
A/D Converter
Reserved
Internal CR trimming
Reserved
External Interrupt Controller
Interrupt Request Batch-Read Function
Reserved
D/A Converter
Reserved
Low Voltage Detector
Deep standby mode Controller
Reserved
CAN prescaler
Multi-function serial Interface
CRC
Watch Counter
RTC/Port Ctrl
Low-speed CR Prescaler
Peripheral Clock Gating
Reserved
External Memory interface
Reserved
DMAC register
DSTC register
CAN ch.0
CAN ch.1
Reserved
GPIO
Reserved
WorkFlash I/F register
Page 60 of 160
S6E2H4 Series
11. Pin Status in Each CPU State
The terms used for pin status have the following meanings.
INITX=0
This is the period when the INITX pin is the L level.
INITX=1
This is the period when the INITX pin is the H level.
SPL=0
This is the status that the standby pin level setting bit (SPL) in the standby mode control register (STB_CTL) is set to 0.
SPL=1
This is the status that the standby pin level setting bit (SPL) in the standby mode control register (STB_CTL) is set to 1.
Input enabled
Indicates that the input function can be used.
Internal input fixed at 0
This is the status that the input function cannot be used. Internal input is fixed at L.
Hi-Z
Indicates that the pin drive transistor is disabled and the pin is put in the Hi-Z state.
Setting disabled
Indicates that the setting is disabled.
Maintain previous state
Maintains the state that was immediately prior to entering the current mode.
If a built-in peripheral function is operating, the output follows the peripheral function.
If the pin is being used as a port, that output is maintained.
Analog input is enabled
Indicates that the analog input is enabled.
Trace output
Indicates that the trace function can be used.
GPIO selected
In Deep standby mode, pins switch to the general-purpose I/O port.
Setting prohibition
Prohibition of a setting by specification limitation.
Document Number: 001-98941 Rev.*C
Page 61 of 160
S6E2H4 Series
Pin status Type
List of Pin Status
A
B
Function
Group
Power-on
Reset or
Low-voltage
Detection
State
INITX
Input
State
Run
Device
Mode
Internal or Sleep
Reset
Mode
State
State
Deep Standby RTC
Mode or Deep Standby
Stop Mode State
Return from
Deep
Standby
Mode State
Power Supply
Stable
Power Supply
Stable
Power
Supply
Stable
INITX=1
-
Power
Supply
Unstable
‐
‐
INITX=0
‐
INITX=1
‐
GPIO
selected
Setting
disabled
Setting
disabled
Maintain
Setting
previous
disabled
state
Maintain
previous
state
Main crystal
oscillator
input pin/
External
main clock
input
selected
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Maintain
previous
state
GPIO
Hi-Z /
Hi-Z /
selected
Internal input
Internal input
Internal input
fixed
fixed
fixed
at 0
at 0
at 0
GPIO
selected
Maintain
previous
state
Hi-Z /
Internal input
fixed
at 0
Maintain
previous
state
Power Supply
Stable
Power
Supply
Stable
INITX=1
‐
Timer Mode,
RTC Mode, or
Stop Mode State
GPIO
selected
Setting
disabled
Setting
disabled
Maintain
Setting
previous
disabled
state
External
main clock
input
selected
Setting
disabled
Setting
disabled
Maintain
Setting
previous
disabled
state
Hi-Z /
Internal
input
fixed
at 0
Hi-Z /
Internal
input
fixed
at 0
Hi-Z /
Main crystal Internal input
oscillator
fixed at 0 /
output pin
or Input
enabled
INITX=1
SPL=0
SPL=1
INITX=1
SPL=0
SPL=1
GPIO
Hi-Z /
Hi-Z /
selected
Internal input
Internal input
Internal input
fixed
fixed
fixed
at 0
at 0
at 0
Input
enabled
Input
enabled
Maintain
previous
state
Input
enabled
Hi-Z /
Internal input
fixed
at 0
GPIO
selected
Input
enabled
Maintain previous state /
When oscillation stops*1, Hi-Z /
Internal input fixed at 0
C
INITX
input pin
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
D
Mode
input pin
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Document Number: 001-98941 Rev.*C
Page 62 of 160
Pin status Type
S6E2H4 Series
E
F
Function
Group
Power-on
Reset or
Low-voltage
Detection
State
INITX
Input
State
Mode
input pin
Power
Supply
Unstable
‐
‐
Input
enabled
INITX=0
‐
Input
enabled
GPIO
selected
Setting
disabled
Setting
disabled
NMIX
selected
Setting
disabled
Setting
disabled
Resource
other than
above
selected
Hi-Z
GPIO
selected
JTAG
selected
Hi-Z
Run
Device
Mode
Internal or Sleep
Reset
Mode
State
State
Power
Supply
Stable
INITX=1 INITX=1
‐
‐
Input
Input
enabled enabled
Maintain
Setting
previous
disabled
state
Power Supply
Stable
Setting
disabled
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
G
H
I
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
JTAG
selected
Hi-Z
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Resource
other than
above
selected
GPIO
selected
Resource
selected
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Document Number: 001-98941 Rev.*C
Maintain
previous
state
Maintain
previous
state
Timer Mode,
RTC Mode, or
Stop Mode State
Deep Standby RTC
Mode or Deep Standby
Stop Mode State
Return from
Deep
Standby
Mode State
Power Supply
Stable
Power Supply
Stable
INITX=1
SPL=0
SPL=1
Input
Input
enabled
enabled
Maintain
Hi-Z /
previous
Input
state
enabled
Maintain
previous
state
INITX=1
SPL=0
SPL=1
Input
Input
enabled
enabled
Hi-Z /
GPIO
Input
selected
enabled
Power
Supply
Stable
INITX=1
Input
enabled
Maintain
previous
state
WKUP
input
enabled
Maintain
previous
state
Hi-Z /
Internal input
fixed
at 0
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
GPIO
selected
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
GPIO
Hi-Z /
Hi-Z /
selected
Internal input
Internal input
Internal input
fixed
fixed
fixed
at 0
at 0
at 0
Maintain
previous
state
Maintain
previous
state
Hi-Z /
WKUP
input
enabled
GPIO
selected
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
GPIO
selected
Maintain
previous
state
GPIO
Hi-Z /
Hi-Z /
selected
Internal input
Internal input
Internal input
fixed
fixed
fixed
at 0
at 0
at 0
GPIO
selected
GPIO
Hi-Z /
Hi-Z /
selected
Internal input
Internal input
Internal input
fixed
fixed
fixed
at 0
at 0
at 0
GPIO
selected
Page 63 of 160
Pin status Type
S6E2H4 Series
Function
Group
Analog
output
selected
J
K
Resource
other than
above
selected
GPIO
selected
External
interrupt
enabled
selected
Resource
other than
above
selected
GPIO
selected
Analog input
selected
Power-on
Reset or
Low-voltage
Detection
State
Run
Device
Mode
Internal or Sleep
Reset
Mode
State
State
Power
Supply
Unstable
‐
‐
INITX=0
‐
INITX=1
‐
Setting
disabled
Setting
disabled
Setting
disabled
Power Supply
Stable
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Setting
disabled
Setting
disabled
Setting
disabled
Power
Supply
Stable
INITX=1
‐
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Input
enabled
Hi-Z
Hi-Z /
Internal
input
fixedat
0/
Analog
input
enabled
Hi-Z /
Internal
input
fixedat
0/
Analog
input
enabled
Setting
disabled
Maintain
Setting
previous
disabled
state
Document Number: 001-98941 Rev.*C
Deep Standby RTC
Mode or Deep Standby
Stop Mode State
Return from
Deep
Standby
Mode State
Power Supply
Stable
Power Supply
Stable
INITX=1
SPL=0
SPL=1
INITX=1
SPL=0
SPL=1
Power
Supply
Stable
INITX=1
-
Maintain
previous
state
*3
GPIO
Hi-Z /
selected
Internal input
Internal input
Hi-Z /
fixed
fixed
Internal input
at 0
at 0
fixed
at 0
GPIO
selected
Maintain
previous
state
Hi-Z /
Input
enabled
Setting
disabled
Timer Mode,
RTC Mode, or
Stop Mode State
*2
Hi-Z
L
Resource
other than
above
selected
GPIO
selected
INITX
Input
State
Maintain
previous
state
GPIO
Hi-Z /
selected
Internal input
Internal input
fixed
Hi-Z /
fixed
at 0
Internal input
at 0
fixed
at 0
GPIO
selected
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Internal
Internal input Internal input Internal input Internal input Internal input
input
fixed
fixed
fixed
fixed
fixed
fixed
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
Analog
Analog
Analog
Analog
Analog
Analog
input
input
input
input
input
input
enabled
enabled
enabled
enabled
enabled
enabled
Maintain
previous
state
GPIO
Hi-Z /
Hi-Z /
selected
Internal input
Internal input
Internal input
fixed
fixed
fixed
at 0
at 0
at 0
GPIO
selected
Page 64 of 160
Pin status Type
S6E2H4 Series
Function
Group
Power
Supply
Unstable
‐
‐
Analog input
selected
M
N
Power-on
Reset or
Low-voltage
Detection
State
External
interrupt
enabled
selected
Resource
other than
above
selected
GPIO
selected
Hi-Z
INITX
Input
State
Run
Device
Mode
Internal or Sleep
Reset
Mode
State
State
Power Supply
Stable
INITX=0
‐
Hi-Z /
Internal
input
fixed
at 0 /
Analog
input
enabled
INITX=1
‐
Hi-Z /
Internal
input
fixed
at 0 /
Analog
input
enabled
Timer Mode,
RTC Mode, or
Stop Mode State
Deep Standby RTC
Mode or Deep Standby
Stop Mode State
Return from
Deep
Standby
Mode State
Power
Power
Power Supply
Power Supply
Supply
Supply
Stable
Stable
Stable
Stable
INITX=1
INITX=1
INITX=1
INITX=1
‐
SPL=0
SPL=1
SPL=0
SPL=1
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Internal
Internal input Internal input Internal input Internal input Internal input
input
fixed
fixed
fixed
fixed
fixed
fixed
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
Analog
Analog
Analog
Analog
Analog
Analog
input
input
input
input
input
input
enabled
enabled
enabled
enabled
enabled
enabled
Maintain
previous
state
Setting
disabled
Setting
disabled
Maintain
Setting
previous
disabled
state
Analog input
selected
Hi-Z
Hi-Z /
Internal
input
fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input
fixed
at 0 /
Analog
input
enabled
Trace
selected
Resource
other than
above
selected
GPIO
selected
Setting
disabled
Setting
disabled
Document Number: 001-98941 Rev.*C
Maintain
previous
state
GPIO
Hi-Z /
selected
Internal input
Internal input
fixed
Hi-Z /
fixed
at 0
Internal input
at 0
fixed
at 0
GPIO
selected
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Internal
Internal input Internal input Internal input Internal input Internal input
input
fixed
fixed
fixed
fixed
fixed
fixed
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
Analog
Analog
Analog
Analog
Analog
Analog
input
input
input
input
input
input
enabled
enabled
enabled
enabled
enabled
enabled
Trace
output
GPIO
Hi-Z /
Maintain
Maintain
selected
Setting
Internal input
GPIO
Hi-Z /
previous
previous
Internal input
disabled
fixed
selected
Internal input
state
state
fixed
at 0
fixed
at 0
at 0
Page 65 of 160
Pin status Type
S6E2H4 Series
Function
Group
Power
Supply
Unstable
‐
‐
Analog input
selected
O
Trace
selected
External
interrupt
enabled
selected
Resource
other than
above
selected
GPIO
selected
Analog input
selected
P
Power-on
Reset or
Low-voltage
Detection
State
Hi-Z
Setting
disabled
INITX
Input
State
Power Supply
Stable
INITX=0
‐
Hi-Z /
Internal
input
fixed
at 0 /
Analog
input
enabled
Setting
disabled
Hi-Z
Hi-Z /
Internal
input
fixedat
0/
Analog
input
enabled
Setting
disabled
Setting
disabled
WKUP
enabled
Resource
other than
above
selected
GPIO
selected
Run
Device
Mode
Internal or Sleep
Reset
Mode
State
State
Document Number: 001-98941 Rev.*C
INITX=1
‐
Hi-Z /
Internal
input
fixed
at 0 /
Analog
input
enabled
Timer Mode,
RTC Mode, or
Stop Mode State
Deep Standby RTC
Mode or Deep Standby
Stop Mode State
Return from
Deep
Standby
Mode State
Power
Power
Power Supply
Power Supply
Supply
Supply
Stable
Stable
Stable
Stable
INITX=1
INITX=1
INITX=1
INITX=1
‐
SPL=0
SPL=1
SPL=0
SPL=1
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Internal
Internal input Internal input Internal input Internal input Internal input
input
fixed
fixed
fixed
fixed
fixed
fixed
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
Analog
Analog
Analog
Analog
Analog
Analog
input
input
input
input
input
input
enabled
enabled
enabled
enabled
enabled
enabled
Trace
output
Maintain
Setting
previous
disabled
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal input
fixed
at 0
GPIO
Hi-Z /
selected
Internal input
Internal input
fixed
fixed
at 0
at 0
GPIO
selected
Hi-Z /
Internal
input
fixedat
0/
Analog
input
enabled
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Internal
Internal input Internal input Internal input Internal input Internal input
input
fixed
fixed
fixed
fixed
fixed
fixed
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
Analog
Analog
Analog
Analog
Analog
Analog
input
input
input
input
input
input
enabled
enabled
enabled
enabled
enabled
enabled
Maintain
WKUP
Hi-Z /
previous
input
WKUP input
state
enabled
enabled
Maintain
Maintain
Setting
GPIO
GPIO
previous
previous
Hi-Z /
Hi-Z /
disabled
selected
selected
state
state
Internal input
Internal input
Internal input
fixed
fixed
fixed
at 0
at 0
at 0
Page 66 of 160
Pin status Type
S6E2H4 Series
Function
Group
Power-on
Reset or
Low-voltage
Detection
State
INITX
Input
State
Run
Device
Mode
Internal or Sleep
Reset
Mode
State
State
Power
Supply
Unstable
‐
‐
INITX=0
‐
INITX=1
‐
Setting
disabled
Setting
disabled
Setting
disabled
Power Supply
Stable
WKUP
enabled
Power
Supply
Stable
INITX=1
‐
Timer Mode,
RTC Mode, or
Stop Mode State
Deep Standby RTC
Mode or Deep Standby
Stop Mode State
Return from
Deep
Standby
Mode State
Power Supply
Stable
Power Supply
Stable
Power
Supply
Stable
INITX=1
-
INITX=1
SPL=0
SPL=1
Maintain
previous
state
INITX=1
SPL=0
SPL=1
Hi-Z /
WKUP input
WKUP
enabled
input
enabled
External
interrupt
Maintain
Maintain
enabled
GPIO
previous
previous
GPIO
Q
selected
selected
Hi-Z /
state
state
selected
Resource
Internal input
Internal input
other than
fixed
Hi-Z /
fixed
Hi-Z /
Hi-Z /
above
at 0
Internal input
at 0
Hi-Z
Input
Input
selected
fixed
enabled enabled
at 0
GPIO
selected
*1: Oscillation is stopped at Sub timer mode, sub CR timer mode, RTC mode, Stop mode, Deep standby RTC mode, and Deep
standby Stop mode.
*2: Maintain previous state at timer mode. GPIO selected Internal input fixed at 0 at RTC mode, Stop mode.
*3: Maintain previous state at timer mode. Hi-Z/Internal input fixed at 0 at RTC mode, Stop mode.
Document Number: 001-98941 Rev.*C
Page 67 of 160
S6E2H4 Series
VBAT Pin Status Type
List of VBAT Domain Pin Status
VBAT
Power-on
reset
Function
Group
GPIO
selected
S
Device
Internal
Reset
State
Power
Power Supply
Supply
Stable
Unstable
‐
INITX=0 INITX=1
‐
‐
‐
Maintain Maintain
Setting
previous previous
disabled
state
state
Sub crystal
oscillator
input pin /
Input
External sub enabled
clock input
selected
GPIO
selected
Setting
disabled
External sub
Setting
clock input
disabled
selected
T
INITX
Input
State
U
Hi-Z
GPIO
selected
Deep Standby
RTC Sode or Deep
Standby Stop Mode
State
Power Supply
Stable
Power Supply
Stable
INITX=1
SPL=0
SPL=1
Maintain Maintain
previous previous
state
state
INITX=1
SPL=0
SPL=1
Maintain Maintain
previous previous
state
state
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
/When
previous
oscillatio
state
n
stops,
Hi-Z*
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Input
enabled
Input
enabled
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain Maintain
previous previous
state
state
Timer Mode,
RTC Mode, or
Stop Mode State
Power
Supply
Stable
INITX=1
‐
Maintain
previous
state
Input
enabled
Hi-Z /
Internal
Sub crystal
Maintain Maintain
input fixed
oscillator
previous previous
at 0/
output pin
state
state
or Input
enabled
Resource
selected
Run
Mode or
Sleep
Mode
State
Maintain
previous
state
Return
from
Deep
Standby
Mode
State
Power
Supply
Stable
INITX=1
GPIO
selected
Input
enabled
GPIO
selected
Maintain
previous
state
Maintain Maintain Maintain
previous previous previous
state
state
state
Maintain
/When
/When
/When
previous
oscillation oscillation oscillation
state
stops,
stops,
stops,
Hi-Z*
Hi-Z*
Hi-Z*
Maintain Maintain
previous previous
state
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
VBAT
RTC
Mode
State
Power
Supply
Stable
Setting
prohibitio
n
Return
from
VBAT
RTC
Mode
State
Power
Supply
Stable
-
Maintain Maintain
previous previous
state
state
Setting
prohibitio
n
Maintain Maintain
previous previous
state
state
Maintain Maintain
previous previous
state
state
Maintain Maintain
previous previous
state
state
*: When The SOSCNTL bit in the WTOSCCNT Register is 0, Sub crystal oscillator output pin is maintain previous state.
When The SOSCNTL bit in the WTOSCCNT Register is 1, Oscillation is stopped at Stop mode and Deep standby Stop mode.
Document Number: 001-98941 Rev.*C
-
Page 68 of 160
S6E2H4 Series
12. Electrical Characteristics
12.1 Absolute Maximum Ratings
Parameter
Symbol
Rating
Unit
Remarks
Min
Max
VCC
VSS - 0.5
VSS + 6.5
V
Power supply voltage (VBAT)
Analog power supply voltage *1 ,*4
VBAT
AVCC
VSS - 0.5
VSS - 0.5
VSS + 6.5
VSS + 6.5
V
V
Analog reference voltage *1 ,*4
AVRH
VSS - 0.5
VSS + 6.5
VCC + 0.5
(≤ 6.5 V)
VSS + 6.5
AVCC + 0.5
(≤ 6.5 V)
VCC + 0.5
(≤ 6.5 V)
10
20
20
22.4
4
8
12
20
100
50
- 10
V
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
4 mA type
8 mA type
12 mA type
I2C Fm+
4 mA type
8 mA type
12 mA type
I2C Fm+
20
- 20
-4
8
- 12
- 100
- 50
+ 150
mA
mA
mA
mA
mA
mA
mA
°C
8 mA type
12 mA type
4 mA type
8 mA type
12 mA type
Power supply voltage *1, *2
*1 ,*3
Input voltage *1
VI
VSS - 0.5
VSS - 0.5
Analog pin input voltage *1
VIA
VSS - 0.5
Output voltage *1
VO
VSS - 0.5
"L" level maximum output current
*5
"L" level average output current *6
"L" level total maximum output current
"L" level total average output current *7
"H" level maximum output current *5
"H" level average output current *6
IOL
-
IOLAV
-
∑IOL
∑IOLAV
-
IOH
-
IOHAV
-
"H" level total maximum output current
∑IOH
"H" level total average output current *7
∑IOHAV
Storage temperature
TSTG
- 55
*1: These parameters are based on the condition that VSS = AVSS = 0.0 V.
V
V
5 V tolerant
V
V
4 mA type
*2: VCC must not drop below VSS - 0.5 V.
*3: VBAT must not drop below VSS - 0.5 V.
*4: Ensure that the voltage does not exceed VCC + 0.5 V, for example, when the power is turned on.
*5: The maximum output current is defined as the value of the peak current flowing through any one of the
corresponding pins.
*6: The average output current is defined as the average current value flowing through any one of the
corresponding pins for a 100-ms period.
*7: The total average output current is defined as the average current value flowing through all of
corresponding pins for a 100-ms.
WARNING:
−
Semiconductor devices may be permanently damaged by application of stress (including, without limitation, voltage, current
or temperature) in excess of absolute maximum ratings.
Do not exceed any of these ratings.
Document Number: 001-98941 Rev.*C
Page 69 of 160
S6E2H4 Series
12.2 Recommended Operating Conditions
Value
Min
Max
Power supply voltage
VCC
2.7*4
5.5
Power supply voltage (VBAT)
VBAT
2.7
5.5
Analog power supply voltage
AVCC
2.7
5.5
Analog reference voltage
AVRH
*3
AVCC
Smoothing capacitor
CS
1
10
Junction temperature
TJ
- 40
+ 125
Operating
temperature
Ambient temperature
TA
- 40
*2
*1: See "●C pin" in "Handling Devices" for the connection of the smoothing capacitor.
Parameter
Symbol
Conditions
Unit
V
V
V
V
μF
°C
°C
Remarks
AVCC=VCC
for built-in regulator *1
*2: The maximum temperature of the ambient temperature (TA) can guarantee a range that does not exceed
the junction temperature (TJ).
The calculation formula of the ambient temperature (TA) is shown below.
TA (Max) = TJ (Max) - Pd(Max) × θja
Pd:
θja:
Power dissipation (W)
Package thermal resistance (°C/W)
Pd (Max) = VCC × ICC (Max) + Σ (IOL×VOL) + Σ ((VCC-VOH) × (- IOH))
IOL:
IOH:
VOL:
VOH:
L level output current
H level output current
L level output voltage
H level output voltage
*3 :The minimum value of Analog reference voltage depends on the value of compare clock cycle
(Tcck). See 12.5 12-bit A/D Converter for the details.
*4: In between less than the minimum power supply voltage and low voltage reset/interrupt detection voltage or more, instruction
execution and low voltage detection function by built-in High-speed CR(including Main PLL is used) or built-in Low-speed CR is
possible to operate only.
Package thermal resistance and maximum permissible power for each package are shown below.
The operation is guaranteed maximum permissible power or less for semiconductor devices.
Table for Package Thermal Resistance and Maximum Permissible Power
Package
LQH080
(0.5-mm pitch)
LQI100
(0.5-mm pitch)
LQM120
(0.5-mm pitch)
FDI121
(0.5-mm pitch)
Printed Circuit Board
Thermal Resistance
θja (°C/W)
Single-layered both sides
4 layers
Single-layered both sides
4 layers
Single-layered both sides
4 layers
Single-layered both sides
4 layers
82
56
59
39
71
50
63
37
Maximum Permissible Power
(mW)
TA=+85°C
TA=+105°C
488
714
678
1026
563
800
635
1081
244
357
339
513
282
400
317
540
WARNING:
1. The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All
of the device's electrical characteristics are warranted when the device is operated under these conditions.
Any use of semiconductor devices will be under their recommended operating condition.
Operation under any conditions other than these conditions may adversely affect reliability of device and could result in device
failure.
No warranty is made with respect to any use, operating conditions or combinations not represented on this data sheet. If you
are considering application under any conditions other than listed herein, please contact sales representatives beforehand.
Document Number: 001-98941 Rev.*C
Page 70 of 160
S6E2H4 Series
Calculation Method of Power Dissipation (Pd)
The power dissipation is shown in the following formula.
Pd = VCC × ICC + Σ (IOL × VOL) + Σ ((VCC-VOH) × (-IOH))
IOL:
L level output current
IOH:
H level output current
VOL:
L level output voltage
VOH:
H level output voltage
ICC is a current consumed in device.
It can be analyzed as follows.
ICC = ICC(INT) + ΣICC(IO)
ICC(INT): Current consumed in internal logic and memory, etc. through regulator
ΣICC(IO): Sum of current (I/O switching current) consumed in output pin
For ICC (INT), it can be anticipated by "(1) Current Rating" in "3. DC Characteristics" (This rating value does not include ICC (IO) for
a value at pin fixed).
For Icc (IO), it depends on system used by customers.
The calculation formula is shown below.
ICC(IO) = (CINT + CEXT) × VCC × fsw
CINT:
Pin internal load capacitance
CEXT:
External load capacitance of output pin
fSW:
Pin switching frequency
Parameter
Symbol
Pin internal load capacitance
CINT
Conditions
Capacitance Value
4 mA type
1.93 pF
8 mA type
3.45 pF
12 mA type
3.42 pF
Calculate ICC (Max) as follows when the power dissipation can be evaluated by yourself.
1. Measure current value ICC (Typ) at normal temperature (+25°C).
2. Add maximum leak current value ICC (leak_max) at operating on a value in (1).
ICC(Max) = ICC(Typ) + ICC(leak_max)
Parameter
Symbol
Maximum leak current at operating
ICC(leak_max)
Document Number: 001-98941 Rev.*C
Conditions
TJ = +125°C
TJ = +105°C
TJ = +85°C
Current Value
16.8 mA
8.6 mA
5.8 mA
Page 71 of 160
S6E2H4 Series
Current Explanation Diagram
Pd = VCC×ICC + Σ(IOL×VOL)+Σ((VCC-VOH)×(-IOH))
ICC = ICC(INT)+ΣICC(IO)
VCC
A
ICC
Chip
ICC(INT)
ΣICC(IO)
A
Regulator
VOL
V
A
・・・
V
IOL
Flash
VOH
・・・
Logic
IOH
RAM
ICC(IO)
CEXT
・・・
Document Number: 001-98941 Rev.*C
Page 72 of 160
S6E2H4 Series
12.3 DC Characteristics
12.3.1 Current Rating
Table 12-1 Typical and Maximum Current Consumption in Normal Operation(PLL), Code Running from Flash Memory
(Flash Accelerator Mode and Trace Buffer Function Enabled)
Pin
Parameter Symbol Name
Power
supply
current
ICC
VCC
Conditions
Frequency*4
Normal operation *5, *6
(PLL)
*9
160 MHz
144 MHz
120 MHz
100 MHz
80 MHz
60 MHz
40 MHz
20 MHz
8 MHz
4 MHz
160 MHz
144 MHz
120 MHz
100 MHz
80 MHz
60 MHz
40 MHz
20 MHz
8 MHz
4 MHz
Value
Typ*1
Max*2
71
51
67
47
39
59
33
53
27
47
20
40
14
34
7.6
28
3.9
24
2.7
23
30
51
48
28
23
43
20
40
36
16
32
12
29
8.7
5.0
25
2.8
23
2.1
22
Unit
Remarks
*3
mA When all peripheral
clocks are ON
*3
mA When all peripheral
clocks are OFF
Table 12-2 Typical and Maximum Current Consumption in Normal Operation(PLL), Code with Data Accessing Running
from Flash Memory (Flash Accelerator Mode and Trace Buffer Function Disabled)
Parameter
Power
supply
current
Symbol
ICC
Pin
Name
VCC
Conditions
Normal
operation
(PLL)
*8 *9
Frequency*7
160 MHz
144 MHz
120 MHz
100 MHz
80 MHz
60 MHz
40 MHz
20 MHz
8 MHz
4 MHz
160 MHz
144 MHz
120 MHz
100 MHz
80 MHz
60 MHz
40 MHz
20 MHz
8 MHz
4 MHz
Value
Typ*1
Max*2
56
51
43
37
30
23
16
8.5
4.3
2.9
30
28
24
20
17
13
9.2
5.3
3.0
2.2
76
71
63
57
50
43
36
29
25
23
51
48
44
41
37
33
30
26
23
23
Unit
Remarks
*3
mA When all peripheral
clocks are ON
*3
mA When all peripheral
clocks are OFF
*1: TA=+25°C, VCC=3.3 V
*2: TJ=+125°C, VCC=5.5 V
*3: When all ports are fixed.
Document Number: 001-98941 Rev.*C
Page 73 of 160
S6E2H4 Series
*4: Frequency is a value of HCLK. PCLK0=PCLK1=PCLK2=HCLK/2
*5: When operating flash accelerator mode and trace buffer function (FRWTR.RWT = 10, FBFCR.BE = 1)
*6: Data access is nothing to MainFlash memory
*7: Frequency is a value of HCLK. PCLK0=PCLK2=HCLK/2, PCLK1=HCLK
*8: When stopping flash accelerator mode and trace buffer function (FRWTR.RWT = 10, FBFCR.BE = 0)
*9: When using the crystal oscillator of 4 MHz (including the current consumption of the oscillation circuit)
Table 12-3 Typical and Maximum Current Consumption in Normal Operation(PLL), Code with Data Accessing Running
from Flash Memory (Flash 0 wait-cycle Mode and Read Access 0 wait)
Parameter Symbol
Pin
Name
Frequency*4
(MHz)
Conditions
72 MHz
60 MHz
48 MHz
Power
supply
current
ICC
VCC
Normal
operation
(PLL)
*5 *6
Value
Typ*1
Max*2
58
38
53
33
48
28
36 MHz
22
42
24 MHz
12 MHz
8 MHz
4 MHz
72 MHz
60 MHz
48 MHz
36 MHz
24 MHz
12 MHz
8 MHz
4 MHz
16
9.5
6.9
4.2
29
26
22
18
13
7.8
5.8
3.7
36
30
27
25
49
46
42
38
33
28
26
24
Unit
Remarks
mA
*3
When all peripheral
clocks are ON
mA
*3
When all peripheral
clocks are OFF
*1: TA=+25°C, VCC=3.3 V
*2: TJ=+125°C, VCC=5.5 V
*3: When all ports are fixed.
*4: Frequency is a value of HCLK. PCLK0=PCLK1=PCLK2=HCLK
*5: When 0 wait-cycle mode (FRWTR.RWT = 00, FSYNDN.SD = 000)
*6: When using the crystal oscillator of 4 MHz (including the current consumption of the oscillation circuit)
Document Number: 001-98941 Rev.*C
Page 74 of 160
S6E2H4 Series
Table 12-4 Typical and Maximum Current Consumption in Normal Operation(other than PLL), Code with Data Accessing
Running from Flash Memory (Flash 0 wait-cycle Mode and Read Access 0 wait)
Parameter Symbol
Pin
Name
Normal operation
(main oscillation)
Normal operation
(built-in
high-speed CR)
Power
supply
current
ICC
Frequency*4
Conditions
*5*6
*5
Value
Normal operation
(built-in
low-speed CR)
*5
*5
Remarks
Max*2
4.0
24
3.2
24
3.2
24
2.7
23
0.34
21
*3
mA When all peripheral
clocks are ON
0.30
21
*3
mA When all peripheral
clocks are OFF
0.36
21
*3
mA When all peripheral
clocks are ON
0.33
21
*3
mA When all peripheral
clocks are OFF
4 MHz
4 MHz
VCC
Normal operation
(sub oscillation)
Unit
Typ*1
32 kHz
100 kHz
*3
mA When all peripheral
clocks are ON
*3
mA When all peripheral
clocks are OFF
*3
mA When all peripheral
clocks are ON
*3
mA When all peripheral
clocks are OFF
*1: TA=+25°C, VCC=3.3 V
*2: TJ=+125°C, VCC=5.5 V
*3: When all ports are fixed.
*4: Frequency is a value of HCLK. PCLK0=PCLK1=PCLK2=HCLK/2
*5: When 0 wait-cycle mode (FRWTR.RWT = 00, FSYNDN.SD = 000)
*6: When using the crystal oscillator of 4 MHz (including the current consumption of the oscillation circuit)
Document Number: 001-98941 Rev.*C
Page 75 of 160
S6E2H4 Series
Table 12-5 Typical and Maximum Current Consumption in Sleep Operation(PLL), when PCLK0 = PCLK1 = PCLK2 =
HCLK/2
Parameter
Power
supply
current
Symbol
ICCS
Pin
Name
VCC
Document Number: 001-98941 Rev.*C
Conditions
Frequency*4
Sleep
operation *6
(PLL)
160 MHz
144 MHz
120 MHz
100 MHz
80 MHz
60 MHz
40 MHz
20 MHz
8 MHz
4 MHz
160 MHz
144 MHz
120 MHz
100 MHz
80 MHz
60 MHz
40 MHz
20 MHz
8 MHz
4 MHz
Value
Typ*1
Max*2
35
32
27
23
18
14
9.9
5.5
3.1
2.3
14
13
11
9.5
7.8
6.3
4.6
2.9
2.2
2.0
55
52
47
43
39
34
30
26
23
23
35
33
31
30
28
27
25
23
23
22
Unit
Remarks
mA
*3
When all peripheral
clocks are ON
mA
*3
When all peripheral
clocks are OFF
Page 76 of 160
S6E2H4 Series
Table 12-6 Typical and Maximum Current Consumption in Sleep Operation(PLL), when PCLK0 = PCLK1 = PCLK2 = HCLK
Parameter
Power
supply
current
Symbol
Pin
Name
ICCS
VCC
Conditions
Sleep
operation *6
(PLL)
Frequency*5
Value
Typ*1
Max*2
72 MHz
60 MHz
23
19
48 MHz
16
43
39
36
36 MHz
12
32
24 MHz
12 MHz
8 MHz
4 MHz
72 MHz
60 MHz
48 MHz
36 MHz
24 MHz
12 MHz
8 MHz
4 MHz
8.5
5.1
3.9
2.7
8.8
7.6
6.3
5.1
3.9
2.7
2.3
1.9
29
25
24
23
29
28
27
25
24
23
23
22
Unit
Remarks
mA
*3
When all peripheral
clocks are ON
mA
*3
When all peripheral
clocks are OFF
*1: TA=+25°C, VCC=3.3 V
*2: TJ=+125°C, VCC=5.5 V
*3: When all ports are fixed.
*4: Frequency is a value of HCLK. PCLK0=PCLK1=PCLK2=HCLK/2
*5: Frequency is a value of HCLK. PCLK0=PCLK1=PCLK2=HCLK
*6: When using the crystal oscillator of 4 MHz (including the current consumption of the oscillation circuit)
Document Number: 001-98941 Rev.*C
Page 77 of 160
S6E2H4 Series
Table 12-7 Typical and Maximum Current Consumption in Sleep Operation(other than PLL), when PCLK0 = PCLK1 =
PCLK2 = HCLK/2
Parameter
Symbol
Pin Name
Conditions
Sleep
operation *5
(main oscillation)
Power
supply
current
Sleep
operation
(built-in highspeed CR)
ICCS
Frequency*4
Value
Typ*1
Max*2
Unit
2.1
22
mA
*3
When all peripheral
clocks are ON
1.3
22
mA
*3
When all peripheral
clocks are OFF
1.3
22
mA
*3
When all peripheral
clocks are ON
0.8
21
mA
0.28
21
mA
0.27
21
mA
0.29
21
mA
*3
When all peripheral
clocks are ON
0.28
21
mA
*3
When all peripheral
clocks are OFF
4MHz
4 MHz
VCC
Sleep
operation
(sub oscillation)
Sleep
operation
(built-in lowspeed CR)
Remarks
32 kHz
100 kHz
*3
When all peripheral
clocks are OFF
*3
When all peripheral
clocks are ON
*3
When all peripheral
clocks are OFF
*1: TA=+25°C, VCC=3.3 V
*2: TJ=+125°C, VCC=5.5 V
*3: When all ports are fixed.
*4: Frequency is a value of HCLK. PCLK0=PCLK1=PCLK2=HCLK/2
*5: When using the crystal oscillator of 4 M Hz (including the current consumption of the oscillation circuit)
Document Number: 001-98941 Rev.*C
Page 78 of 160
S6E2H4 Series
Table 12-8 Typical and Maximum Current Consumption in Stop Mode, Timer Mode and RTC Mode
Parameter
Symbol Pin Name
ICCH
Conditions
Stop mode
Timer mode *5
(main oscillation)
Timer mode (builtin high-speed CR)
Power supply
current
ICCT
Frequency
-
4 MHz
4 MHz
Value
Typ*1
Max*2
Unit
0.21
0.94
mA
-
7.6
mA
-
10
mA
1.4
2.1
mA
-
8.8
mA
-
11
mA
0.49
1.2
mA
-
7.9
mA
-
11
mA
0.23
0.96
mA
-
7.6
mA
-
10
mA
0.24
0.97
mA
-
7.6
mA
-
10
mA
0.21
0.94
mA
-
7.6
mA
-
10
mA
VCC
Timer mode
(sub oscillation)
Timer mode
(built-in
low-speed CR)
ICCR
RTC mode
(sub oscillation)
32 kHz
100 kHz
32 kHz
Remarks
*3, *4
TA=+25°C
*3, *4
TA=+85°C
*3, *4
TA=+105°C
*3, *4
TA=+25°C
*3, *4
TA=+85°C
*3, *4
TA=+105°C
*3, *4
TA=+25°C
*3, *4
TA=+85°C
*3, *4
TA=+105°C
*3, *4
TA=+25°C
*3, *4
TA=+85°C
*3, *4
TA=+105°C
*3, *4
TA=+25°C
*3, *4
TA=+85°C
*3, *4
TA=+105°C
*3, *4
TA=+25°C
*3, *4
TA=+85°C
*3, *4
TA=+105°C
*1: VCC=3.3 V
*2: VCC=5.5 V
*3: When all ports are fixed.
*4: When LVD is OFF
*5: When using the crystal oscillator of 4 M Hz (including the current consumption of the oscillation circuit)
Document Number: 001-98941 Rev.*C
Page 79 of 160
S6E2H4 Series
Table 12-9 Typical and Maximum Current Consumption in Deep Standby Stop Mode, Deep Standby RTC Mode and VBAT
*1: VCC=3.3 V
Parameter
Symbol
Pin Name
Conditions
Frequency
Deep standby
Stop mode
(When RAM is
OFF)
ICCHD
Typ*1
Value
Max*2
Unit
24
40
µA
-
640
µA
-
813
µA
41
146
µA
-
1616
µA
-
2059
µA
24
40
µA
-
640
µA
-
813
µA
41
146
µA
-
1616
µA
-
2059
µA
0.015
0.14
µA
-
4.0
µA
-
9.4
µA
1.3
2.4
µA
-
6.2
µA
-
12
µA
Deep standby
Stop mode
(When RAM is
ON)
VCC
Power
supply
current
Deep standby
RTC mode
(When RAM is
OFF)
ICCRD
32kHz
Deep standby
RTC mode
(When RAM is
ON)
RTC stop
ICCVBAT
VBAT
RTC operation
*6
Remarks
*3, *4
TA=+25°C
*3, *4
TA=+85°C
*3, *4
TA=+105°C
*3, *4
TA=+25°C
*3, *4
TA=+85°C
*3, *4
TA=+105°C
*3, *4
TA=+25°C
*3, *4
TA=+85°C
*3, *4
TA=+105°C
*3, *4
TA=+25°C
*3, *4
TA=+85°C
*3, *4
TA=+105°C
*3, *4, *5
TA=+25°C
*3, *4, *5
TA=+85°C
*3, *4, *5
TA=+105°C
*3, *4
TA=+25°C
*3, *4
TA=+85°C
*3, *4
TA=+105°C
*2: VCC=5.5 V
*3: When all ports are fixed.
*4: When LVD is OFF
*5: When sub oscillation is OFF
*6: When using the crystal oscillator of 32 kHz (including the current consumption of the oscillation circuit)
Document Number: 001-98941 Rev.*C
Page 80 of 160
S6E2H4 Series
Table 12-10 Typical and Maximum Current Consumption in Low-voltage Detection Circuit, Main Flash Memory Write/erase
Parameter
Symbol
Low-voltage
detection circuit
(LVD) power
supply current
ICCLVD
Main flash
memory
write/erase
current
ICCFLASH
Work flash
memory
write/erase
current
ICCWFLASH
Min
Value
Typ
Max
At operation
-
4
7
μA
At Write/Erase
-
13.4
15.9
mA
At Write/Erase
-
11.5
13.6
mA
Pin Name
VCC
Conditions
Unit
Remarks
For occurrence of
interrupt
*1
1: When programming or erase in flash memory, Flash Memory Write/Erase current (I CCFLASH) is added to the Power
supply current (ICC).
Table 12-11 Peripheral Current Dissipation
Clock System
HCLK
PCLK1
PCLK2
Frequency (MHz)
80
160
Peripheral
Unit
GPIO
All ports
0.16
0.32
0.62
DMAC
-
0.68
1.35
2.63
DSTC
-
0.93
1.88
3.65
External bus I/F
-
0.17
0.34
0.71
CAN
1ch.
0.01
0.02
0.03
Base timer
4ch.
0.18
0.37
0.73
1unit/4ch.
0.61
1.22
2.43
Multi-functional
timer/PPG
Quadrature
position/Revolution
counter
40
1unit
0.04
0.07
0.14
A/DC
1unit
0.22
0.44
0.88
Muli-function serial
1ch.
0.30
0.60
-
Document Number: 001-98941 Rev.*C
Unit
Remarks
mA
TA=+25°C,
VCC=3.3 V
mA
TA=+25°C,
VCC=3.3 V
mA
TA=+25°C,
VCC=3.3 V
Page 81 of 160
S6E2H4 Series
12.3.2 Pin Characteristics
(VCC = AVCC = 2.7V to 5.5V, VSS = AVSS = 0V)
Parameter
H level input
voltage
(hysteresis
input)
L level input
voltage
(hysteresis
input)
Symbol
VIHS
VILS
Pin Name
CMOS
hysteresis
input pin, MD0,
MD1
5 V tolerant
input pin
Input pin
doubled as I2C
Fm+
CMOS
hysteresis
input pin, MD0,
MD1
5 V tolerant
input pin
Input pin
doubled as I2C
Fm+
4 mA type
8 mA type
H level output
voltage
VOH
12 mA type
The pin
doubled as I2C
Fm+
Document Number: 001-98941 Rev.*C
Conditions
Value
Unit
Min
Typ
Max
-
VCC×0.8
-
VCC + 0.3
V
-
VCC×0.8
-
VSS + 5.5
V
-
VCC×0.7
-
VSS + 5.5
V
-
VSS - 0.3
-
VCC×0.2
V
-
VSS - 0.3
-
VCC×0.2
V
-
VSS
-
VCC×0.3
V
VCC - 0.5
-
VCC
V
VCC - 0.5
-
VCC
V
VCC - 0.5
-
VCC
V
VCC - 0.5
-
VCC
V
VCC ≥ 4.5 V,
IOH = - 4 mA
VCC < 4.5 V,
IOH = - 2 mA
VCC ≥ 4.5 V,
IOH = - 8 mA
VCC < 4.5 V,
IOH = - 4 mA
VCC ≥ 4.5 V,
IOH = - 12 mA
VCC < 4.5 V,
IOH = - 8 mA
VCC ≥ 4.5 V,
IOH = - 4 mA
VCC < 4.5 V,
IOH = - 3 mA
Remarks
At GPIO
Page 82 of 160
S6E2H4 Series
Value
Parameter
Symbol
Pin Name
4 mA type
8 mA type
L level output
voltage
VOL
12 mA type
Conditions
VCC ≥ 4.5 V,
IOL = 4 mA
VCC < 4.5 V,
IOL = 2 mA
VCC ≥ 4.5 V,
IOH = 8 mA
VCC < 4.5 V,
IOH = 4 mA
VCC ≥ 4.5 V,
IOL = 12 mA
VCC < 4.5 V,
IOL = 8 mA
Unit
Min
Typ
Max
VSS
-
0.4
V
VSS
-
0.4
V
VSS
-
0.4
V
VCC ≥ 4.5 V,
IOH = 4 mA
The pin
doubled as I2C
Fm+
VCC < 4.5 V,
IOH = 3 mA
At GPIO
VSS
-
0.4
V
VCC ≤ 5.5 V,
IOH = 20 mA
Input leak
current
Pull-up resistor
value
Input
capacitance
At I2C Fm+
IIL
-
-
-5
-
+5
μA
RPU
Pull-up pin
VCC ≥ 4.5 V
VCC < 4.5 V
25
30
50
80
100
200
kΩ
CIN
Other than
VCC,
VBAT,
VSS,
AVCC,
AVSS, AVRH
-
-
5
15
pF
Document Number: 001-98941 Rev.*C
Remarks
Page 83 of 160
S6E2H4 Series
12.4 AC Characteristics
12.4.1 Main Clock Input Characteristics
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Input frequency
Pin Name
fCH
Input clock cycle
tCYLH
Input clock pulse
width
Input clock rising
time and falling time
Internal operating
clock*1 frequency
X0,
X1
tCF,
tCR
fCC
fCP0
fCP1
fCP2
-
Conditions
Value
Min
Max
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
PWH/tCYLH,
PWL/tCYLH
4
4
4
4
20.83
50
48
20
48
20
250
250
45
-
Unit
Remarks
MHz
When crystal oscillator is
connected
MHz
When using external clock
ns
When using external clock
55
%
When using external clock
-
5
ns
When using external clock
-
160
80
160
80
MHz
MHz
MHz
MHz
Base clock (HCLK/FCLK)
APB0 bus clock*2
APB1 bus clock*2
APB2 bus clock*2
tCYCC
6.25
ns
Base clock (HCLK/FCLK)
tCYCP0
12.5
ns
APB0 bus clock*2
tCYCP1
6.25
ns
APB1 bus clock*2
tCYCP2
12.5
ns
APB2 bus clock*2
*1: For more information about each internal operating clock, see Chapter 2-1: Clock in FM4 Family
Peripheral Manual Main part(MN709-00001).
Internal operating
clock*1 cycle time
*2: For about each APB bus which each peripheral is connected to, see 8. Block Diagram in this data sheet.
X0
Document Number: 001-98941 Rev.*C
Page 84 of 160
S6E2H4 Series
12.4.2 Sub Clock Input Characteristics
(VBAT = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Input frequency
Pin
Name
Conditions
-
-
-
32
Typ
32.76
8
-
PWH/tCYLL,
PWL/tCYLL
10
45
1/ tCYLL
Input clock cycle
Input clock pulse
width
tCYLL
X0A,
X1A
-
Value
Min
0.8 × VBAT
Max
Unit
-
kHz
100
kHz
When crystal oscillator is
connected
When using external clock
-
31.25
μs
When using external clock
-
55
%
When using external clock
VBAT
VBAT
VBAT
VBAT
X0A
Remarks
12.4.3 Built-in CR Oscillation Characteristics
Built-in High-speed CR
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Clock frequency
Clock frequency
Symbol
Conditions
Value
Min
Typ
Max
TJ = -20°C to + 105°C
3.92
4
4.08
TJ = - 40°C to + 125°C
3.88
4
4.12
TJ = - 40°C to + 125°C
2.9
4
5
Unit
fCRH
fCRH
Remarks
When trimming*1
MHz
When not trimming
Frequency
tCRWT
30
μs
*2
Stabilization time
*1: In the case of using the values in CR trimming area of Flash memory at shipment for frequency/temperature trimming.
*2: This is the time to stabilize the frequency of high-speed CR clock after setting trimming value.
This period is able to use high-speed CR clock as source clock.
Built-in Low-speed CR
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Clock frequency
Symbo
l
Condition
fCRL
-
Document Number: 001-98941 Rev.*C
Value
Min
Typ
Max
50
100
150
Unit
Remarks
kHz
Page 85 of 160
S6E2H4 Series
12.4.4 Operating Conditions of Main PLL (In the Case of Using Main Clock for Input Clock of PLL)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
PLL oscillation stabilization wait
time*1
(LOCK UP time)
PLL input clock frequency
PLL multiplication rate
PLL macro oscillation clock
frequency
Main PLL clock frequency*2
Value
Unit
Min
Typ
Max
tLOCK
200
-
-
μs
fPLLI
-
4
13
200
-
16
80
320
MHz
multiplier
-
-
160
MHz
fPLLO
fCLKPLL
-
Remarks
MHz
*1: Time from when the PLL starts operating until the oscillation stabilizes.
*2: For more information about Main PLL clock (CLKPLL), see Chapter 2-1: Clock in FM4 Family Peripheral Manual Main
part(MN709-00001).
12.4.5 Operating Conditions of Main PLL (In the Case of Using Built-in High-speed CR Clock for Input Clock of Main
PLL)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
PLL oscillation stabilization wait
time*1
(LOCK UP time)
PLL input clock frequency
PLL multiplication rate
PLL macro oscillation clock
frequency
Main PLL clock frequency*2
Value
Unit
Min
Typ
Max
tLOCK
200
-
-
μs
fPLLI
-
3.8
50
4
-
MHz
multiplier
fPLLO
190
-
4.2
75
320
fCLKPLL
-
-
160
MHz
Remarks
MHz
*1: Time from when the PLL starts operating until the oscillation stabilizes.
*2: For more information about Main PLL clock (CLKPLL), see Chapter 2-1: Clock in FM4 Family Peripheral Manual Main
part(MN709-00001).
Note:
−
Make sure to input to the main PLL source clock, the high-speed CR clock (CLKHC) that the frequency and temperature has
been trimmed.
12.4.6 Reset Input Characteristics
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Reset input time
Symbol
tINITX
Document Number: 001-98941 Rev.*C
Pin Name Condition
INITX
-
Value
Min
Max
500
-
Unit
Remarks
ns
Page 86 of 160
S6E2H4 Series
12.4.7 Power-on Reset Timing
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Power supply rising time
tVCCR
Power supply shut down time
Time until releasing
Power-on reset
tOFF
Pin Name
VCC
tPRT
Value
Unit
Min
Max
0
-
ms
1
-
ms
0.33
0.60
ms
Remarks
VCC_minimum
VCC
VDH_minimum
0.2V
0.2V
0.2V
tVCCR
tPRT
Internal RST
RST Active
CPU Operation
tOFF
Release
start
Glossary
VCC_minimum: Minimum VCC of recommended operating conditions.
VDH_minimum: Minimum detection voltage of Low-Voltage detection reset.
See 8. Low-Voltage Detection Characteristics.
Document Number: 001-98941 Rev.*C
Page 87 of 160
S6E2H4 Series
12.4.8 GPIO Output Characteristics
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Output frequency
Symbol
Pin Name
Conditions
tPCYCLE
Pxx*
VCC ≥ 4.5 V
VCC < 4.5 V
Value
Min
Max
-
50
32
Unit
MHz
MHz
*: GPIO is a target.
Pxx
tPCYCLE
Document Number: 001-98941 Rev.*C
Page 88 of 160
S6E2H4 Series
12.4.9 External Bus Timing
External Bus Clock Output Characteristics
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Output frequency
Symbol
Pin Name
Conditions
tCYCLE
MCLKOUT*1
VCC ≥ 4.5 V
VCC < 4.5 V
Value
Min
Max
-
50*2
32*3
Unit
MHz
MHz
*1: The external bus clock (MCLKOUT) is a divided clock of HCLK.
For more information about setting of clock divider, see Chapter 14: External Bus Interface in FM4 Family Peripheral Manual
Main part(MN709-00001).
*2: Generate MCLKOUT at setting more than 4 division when the AHB bus clock exceeds 100 MHz.
*3: Generate MCLKOUT at setting more than 4 division when the AHB bus clock exceeds 64 MHz.
0.8 × Vcc
0.8 × Vcc
MCLK
tCYCLE
External Bus Signal Input/output Characteristics
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Conditions
Value
Unit
0.8 × VCC
V
0.2 × VCC
V
VOH
0.8 × VCC
V
VOL
0.2 × VCC
V
VIH
Remarks
Signal input characteristics
VIL
Signal output characteristics
Signal input
VIH
VIL
VIH
VIL
Signal output
VOH
VOL
VOH
VOL
Document Number: 001-98941 Rev.*C
Page 89 of 160
S6E2H4 Series
Separate Bus Access Asynchronous SRAM Mode
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
MOEX
Mininum pulse width
MCSX↓→Address output
delay time
MOEX↑→Address hold time
MCSX↓→
MOEX↓ delay time
MOEX↑→
MCSX↑ time
MCSX↓→MDQM↓
delay time
Data set up→MOEX↑ time
MOEX↑→
Data hold time
MWEX
Mininum pulse width
MWEX↑→Address output
delay time
Symbol
Pin Name
tOEW
MOEX
tCSL – AV
tOEH - AX
tCSL - OEL
tOEH - CSH
tCSL - RDQML
tDS - OE
tDH - OE
MOEX,
MCSX[7:0]
MCSX,
MDQM[1:0]
MOEX,
MADATA[15:0]
MOEX,
MADATA[15:0]
tWEW
MWEX
tWEH - AX
MWEX,
MAD[24:0]
MCSX↓→MWEX↓ delay time
tCSL - WEL
MWEX↑→MCSX↑ delay time
tWEH - CSH
MCSX↓→MDQM↓ delay time
tCSL-WDQML
MWEX↓→
Data output time
MWEX↑→
Data hold time
MCSX[7:0],
MAD[24:0]
MOEX,
MAD[24:0]
tCSL-DX
tWEH - DX
MWEX,
MCSX[7:0]
MCSX,
MDQM[1:0]
MCSX,
MADATA[15:0]
MWEX,
MADATA[15:0]
Conditions
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
Value
Unit
Min
Max
MCLK×n-3
-
-9
-12
MCLK×m-9
MCLK×m-12
20
38
+9
+12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
-
0
-
ns
MCLK×n-3
-
ns
0
MCLK×m-9
MCLK×m-12
0
0
MCLK×n-9
MCLK×n-12
0
MCLK×n-9
MCLK×n-12
MCLK-9
MCLK-12
0
ns
MCLK×m+9
MCLK×m+12
MCLK×n+9
MCLK×n+12
MCLK×m+9
MCLK×m+12
MCLK×n+9
MCLK×n+12
MCLK+9
MCLK+12
MCLK×m+9
MCLK×m+12
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Note:
−
When the external load capacitance CL = 30 pF (m=0 to 15, n=1 to 16)
Document Number: 001-98941 Rev.*C
Page 90 of 160
S6E2H4 Series
tCYCLE
MCLK
tOEH-CSH
MCSX[7:0]
MAD[24:0]
MOEX
tCSL-AV
tWEH-CSH
tOEH-AX
Address
tWEH-AX
tCSL-AV
Address
tCSL-OEL
tOEW
tCSL-WDQML
tCSL-RDQML
tCSL-WEL
MDQM[1:0]
tWEW
MWEX
MADATA[15:0]
tDS-OE
tDH-OE
RD
tWEH-DX
WD
Invalid
tCSL-DX
Document Number: 001-98941 Rev.*C
Page 91 of 160
S6E2H4 Series
Separate Bus Access Synchronous SRAM Mode
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Address delay time
Symbol
Pin Name
Conditions
tAV
MCLK,
MAD[24:0]
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
tCSL
MCSX delay time
tCSH
tREL
MOEX delay time
tREH
MCLK,
MCSX[7:0]
MCLK,
MOEX
Data set up
→MCLK↑ time
tDS
MCLK,
MADATA[15:0]
MCLK↑→
Data hold time
tDH
MCLK,
MADATA[15:0]
tWEL
MWEX delay time
tWEH
MDQM[1:0]
delay time
tDQML
tDQMH
MCLK,
MWEX
MCLK,
MDQM[1:0]
MCLK↑→
Data output time
tODS
MCLK,
MADATA[15:0]
MCLK↑→
Data hold time
tOD
MCLK,
MADATA[15:0]
Value
Min
1
1
1
1
1
Max
9
12
9
12
9
12
9
12
9
12
Unit
ns
ns
ns
ns
ns
19
37
-
ns
0
-
ns
1
1
1
1
MCLK+1
1
9
12
9
12
9
12
9
12
MCLK+18
MCLK+24
18
24
ns
ns
ns
ns
ns
ns
Note:
−
When the external load capacitance CL = 30 pF
Document Number: 001-98941 Rev.*C
Page 92 of 160
S6E2H4 Series
tCYCLE
MCLK
tCSL
tCSH
MCSX[7:0]
tAV
tAV
Address
MAD[24:0]
Address
tREL
tREH
tDQML
tDQMH
MOEX
tDQML
tDQMH
tWEL
tWEH
MDQM[1:0]
MWEX
tDS
tDH
RD
MADATA[15:0]
Document Number: 001-98941 Rev.*C
tOD
WD
Invalid
tODS
Page 93 of 160
S6E2H4 Series
Multiplexed Bus Access Asynchronous SRAM Mode
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Multiplexed address delay
time
tALE-CHMADV
Multiplexed address hold
time
tCHMADH
Pin Name
MALE,
MADATA[15:0]
Conditions
Value
Min
Max
10
20
VCC ≥ 4.5 V
VCC < 4.5 V
0
VCC ≥ 4.5 V
MCLK×n+0
MCLK×n+10
VCC < 4.5 V
MCLK×n+0
MCLK×n+20
Unit
ns
ns
Note:
−
When the external load capacitance CL = 30 pF (m=0 to 15, n=1 to 16)
MCLK
MCSX[7:0]
MALE
MAD [24:0]
MOEX
MDQM [1:0]
MWEX
MADATA[15:0]
Document Number: 001-98941 Rev.*C
Page 94 of 160
S6E2H4 Series
Multiplexed Bus Access Synchronous SRAM Mode
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
tCHAL
MALE delay time
tCHAH
MCLK↑→
Multiplexed address delay time
Pin Name
Conditions
MCLK,
ALE
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
Min
1
1
Max
9
12
9
12
Unit
Remarks
ns
ns
ns
ns
VCC ≥ 4.5 V
tCHMADV
MCLK,
MADATA[15:0]
MCLK↑→
Multiplexed data output time
Value
1
tOD
ns
1
tOD
ns
VCC < 4.5 V
VCC ≥ 4.5 V
tCHMADX
VCC < 4.5 V
Note:
−
When the external load capacitance CL = 30 pF
MCLK
MCSX[7:0]
MALE
MAD [24:0]
MOEX
MDQM [1:0]
MWEX
MADATA[15:0]
Document Number: 001-98941 Rev.*C
Page 95 of 160
S6E2H4 Series
NAND Flash Mode
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
MNREX
Min pulse width
Data set up
→MNREX↑ time
MNREX↑→
Data hold time
MNALE↑→
MNWEX delay time
MNALE↓→
MNWEX delay time
MNCLE↑→
MNWEX delay time
MNWEX↑→
MNCLE delay time
MNWEX
Min pulse width
MNWEX↓→
Data output time
MNWEX↑→
Data hold time
Symbol
Pin Name
tNREW
MNREX
tDS – NRE
tDH – NRE
tALEH - NWEL
tALEL - NWEL
tCLEH - NWEL
tNWEH - CLEL
tNWEW
tNWEL – DV
tNWEH – DX
MNREX,
MADATA[15:0]
MNREX,
MADATA[15:0]
MNALE,
MNWEX
MNALE,
MNWEX
MNCLE,
MNWEX
MNCLE,
MNWEX
MNWEX
MNWEX,
MADATA[15:0]
MNWEX,
MADATA[15:0]
Conditions
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
VCC ≥ 4.5 V
VCC < 4.5 V
Value
Unit
Min
Max
MCLK×n-3
-
ns
20
38
-
ns
0
-
ns
MCLK×m-9
MCLK×m-12
MCLK×m-9
MCLK×m-12
MCLK×m-9
MCLK×m-12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
0
MCLK×n-3
-
-9
-12
+9
+12
MCLK×m+9
MCLK×m+12
0
ns
ns
ns
ns
ns
ns
ns
Note:
−
When the external load capacitance CL = 30 pF (m=0 to 15, n=1 to 16)
NAND Flash Read
MCLK
MNREX
MADATA[15:0]
Read
Document Number: 001-98941 Rev.*C
Page 96 of 160
S6E2H4 Series
NAND Flash Address Write
MCLK
MNALE
MNCLE
MNWEX
MADATA[15:0]
Write
NAND Flash Command Write
MCLK
MNALE
MNCLE
MNWEX
MADATA[15:0]
Write
Document Number: 001-98941 Rev.*C
Page 97 of 160
S6E2H4 Series
External Ready Input Timing
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Pin Name
tRDYI
MCLK,
MRDY
MCLK↑
MRDY input
setup time
Conditions
Value
Min
VCC ≥ 4.5 V
19
VCC < 4.5 V
37
Max
-
Unit
Remarks
ns
When RDY is input
···
MCLK
Over 2cycle
Original
MOEX
MWEX
tRDYI
MRDY
When RDY is released
MCLK
··· ···
2 cycle
Extended
MOEX
MWEX
tRDYI
0.5×VCC
MRDY
Document Number: 001-98941 Rev.*C
Page 98 of 160
S6E2H4 Series
SDRAM Mode
(VCC = 2.7V to 3.6V, VSS = 0V)
Parameter
Symbol
Pin Name
Output frequency
tCYCSD
Address delay time
Value
Unit
Min
Max
MSDCLK
-
32
MHz
tAOSD
MSDCLK,
MAD[15:0]
2
12
ns
MSDCLK↑→Data output delay time
tDOSD
MSDCLK,
MADATA[31:0]
2
12
ns
MSDCLK↑→Data output
Hi-Z time
tDOZSD
MSDCLK,
MADATA[31:0]
2
20
ns
MDQM[1:0] delay time
tWROSD
MSDCLK,
MDQM[1:0]
1
12
ns
MCSX delay time
tMCSSD
MSDCLK,
MCSX8
2
12
ns
MRASX delay time
tRASSD
MSDCLK,
MRASX
2
12
ns
MCASX delay time
tCASSD
MSDCLK,
MCASX
2
12
ns
MSDWEX delay time
tMWESD
MSDCLK,
MSDWEX
2
12
ns
MSDCKE delay time
tCKESD
MSDCLK,
MSDCKE
2
12
ns
Data set up time
tDSSD
MSDCLK,
MADATA[31:0]
23
-
ns
Data hold time
tDHSD
MSDCLK,
MADATA[31:0]
0
-
ns
Note:
−
When the external load capacitance CL = 30 pF
Document Number: 001-98941 Rev.*C
Page 99 of 160
S6E2H4 Series
SDRAM Access
tCYCSD
MSDCLK
tAOSD
MAD[24:0]
MDQM[1:0]
MCSX
MRASX
MCASX
MSDWEX
MSDCKE
Address
tWROSD
tMCSSD
tRASSD
tCASSD
tMWESD
tCKESD
tDSSD
MADATA[15:0]
tDOSD
MADATA[15:0]
Document Number: 001-98941 Rev.*C
tDHSD
RD
tDOZSD
WD
Page 100 of 160
S6E2H4 Series
12.4.10 Base Timer Input Timing
Timer Input Timing
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Input pulse width
Symbol
Pin Name
Conditions
tTIWH,
tTIWL
TIOAn/TIOBn
(when using as
ECK, TIN)
-
tTIWH
Value
Min
Max
2tCYCP
-
Unit
Remarks
ns
tTIWL
ECK
VIHS
VIHS
TIN
VILS
VILS
Trigger Input Timing
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Input pulse width
Symbol
Pin Name
Conditions
tTRGH,
tTRGL
TIOAn/TIOBn
(when using as
TGIN)
-
Value
Min
Max
2tCYCP
-
Unit
Remarks
ns
TGIN
Note:
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which the Base Timer is connected to, see 8. Block Diagram in this data sheet.
Document Number: 001-98941 Rev.*C
Page 101 of 160
S6E2H4 Series
12.4.11 CSIO Timing
Synchronous Serial (SPI = 0, SCINV = 0)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol Pin Name Conditions
Serial clock cycle time
tSCYC
SCK↓→SOT delay time
tSLOVI
SIN→SCK↑
setup time
tIVSHI
SCK↑→SIN hold time
tSHIXI
Serial clock L pulse width
Serial clock H pulse width
tSLSH
tSHSL
SCK↓→SOT delay time
tSLOVE
SIN→SCK↑
setup time
tIVSHE
SCK↑→SIN hold time
tSHIXE
SCK falling time
SCK rising time
tF
tR
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
Internal shift
clock
operation
External shift
clock
operation
VCC < 4.5 V
Min
Max
VCC ≥ 4.5 V
Min
Max
Unit
4tCYCP
-
4tCYCP
-
ns
- 30
+ 30
- 20
+ 20
ns
50
-
30
-
ns
0
-
0
-
ns
2tCYCP - 10
tCYCP + 10
-
2tCYCP - 10
tCYCP + 10
-
ns
ns
-
50
-
30
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
Notes:
−
The above characteristics apply to CLK synchronous mode.
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
These characteristics only guarantee the same relocate port number.
For example, the combination of SCLKx_0 and SOTx_1 is not guaranteed.
−
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 102 of 160
S6E2H4 Series
tSCYC
VOH
SCK
VOL
VOL
tSLOVI
VOH
VOL
SOT
tIVSHI
VIH
VIL
SIN
tSHIXI
VIH
VIL
MS bit = 0
tSLSH
VIH
SCK
tF
VIL
tSHSL
VIL
SIN
VIH
tR
tSLOVE
SOT
VIH
VOH
VOL
tIVSHE
VIH
VIL
tSHIXE
VIH
VIL
MS bit = 1
Document Number: 001-98941 Rev.*C
Page 103 of 160
S6E2H4 Series
Synchronous Serial (SPI = 0, SCINV = 1)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Serial clock cycle time
tSCYC
SCK↑→SOT delay time
tSHOVI
SIN→SCK↓
setup time
tIVSLI
SCK↓→SIN hold time
tSLIXI
Serial clock L pulse width
Serial clock H pulse width
tSLSH
tSHSL
SCK↑→SOT delay time
tSHOVE
SIN→SCK↓
setup time
tIVSLE
SCK↓→SIN hold time
tSLIXE
SCK falling time
SCK rising time
tF
tR
Pin
Name
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
Conditions
Internal shift
clock operation
External shift
clock operation
VCC < 4.5 V
Min
Max
4tCYCP
-
VCC ≥ 4.5 V
Min
Max
4tCYCP
-
Unit
ns
- 30
+ 30
- 20
+ 20
ns
50
-
30
-
ns
0
-
0
-
ns
2tCYCP - 10
tCYCP + 10
-
2tCYCP - 10
tCYCP + 10
-
ns
ns
-
50
-
30
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
Notes:
−
The above characteristics apply to CLK synchronous mode.
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
These characteristics only guarantee the same relocate port number.
For example, the combination of SCLKx_0 and SOTx_1 is not guaranteed.
−
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 104 of 160
S6E2H4 Series
tSCYC
VOH
SCK
VOH
VOL
tSHOVI
VOH
VOL
SOT
tIVSLI
VIH
VIL
SIN
tSLIXI
VIH
VIL
MS bit = 0
tSHSL
VIH
VIL
SCK
tR
tSLSH
tSHOVE
SOT
SIN
VIH
VIL
VIL
tF
VOH
VOL
tIVSLE
VIH
VIL
tSLIXE
VIH
VIL
MS bit = 1
Document Number: 001-98941 Rev.*C
Page 105 of 160
S6E2H4 Series
Synchronous Serial (SPI = 1, SCINV = 0)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Pin Name
Serial clock cycle time
tSCYC
SCK↑→SOT delay time
tSHOVI
SIN→SCK↓
setup time
tIVSLI
SCK↓→SIN hold time
tSLIXI
SOT→SCK↓ delay time
tSOVLI
Serial clock L pulse width
Serial clock H pulse width
tSLSH
tSHSL
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx,
SOTx
SCKx
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
SCK↑→SOT delay time
tSHOVE
SIN→SCK↓
setup time
tIVSLE
SCK↓→SIN hold time
tSLIXE
SCK falling time
SCK rising time
tF
tR
Conditions
Internal shift
clock operation
External shift
clock operation
VCC < 4.5 V
Min
Max
4tCYCP
-
VCC ≥ 4.5 V
Min
Max
4tCYCP
-
Unit
ns
- 30
+ 30
- 20
+ 20
ns
50
-
30
-
ns
0
-
0
-
ns
2tCYCP - 30
-
2tCYCP - 30
-
ns
2tCYCP - 10
tCYCP + 10
-
2tCYCP - 10
tCYCP + 10
-
ns
ns
-
50
-
30
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
Notes:
−
The above characteristics apply to CLK synchronous mode.
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
These characteristics only guarantee the same relocate port number.
For example, the combination of SCLKx_0 and SOTx_1 is not guaranteed.
−
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 106 of 160
S6E2H4 Series
tSCYC
VOH
VOL
SCK
SOT
VOH
VOL
VOH
VOL
tIVSLI
tSLIXI
VIH
VIL
SIN
VOL
tSHOVI
tSOVLI
VIH
VIL
MS bit = 0
tSLSH
VIH
SCK
VIL
tSHSL
VIH
VIL
tF
*V
tR
VIH
tSHOVE
VOH
VOL
OH
VOL
tIVSLE
SOT
SIN
tSLIXE
VIH
VIL
VIH
VIL
MS bit = 1
*: Changes when writing to TDR register
Document Number: 001-98941 Rev.*C
Page 107 of 160
S6E2H4 Series
Synchronous Serial (SPI = 1, SCINV = 1)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Serial clock cycle time
tSCYC
SCK↓→SOT delay time
tSLOVI
SIN→SCK↑
setup time
tIVSHI
SCK↑→SIN hold time
tSHIXI
SOT→SCK↑ delay time
tSOVHI
Serial clock L pulse width
Serial clock H pulse width
tSLSH
tSHSL
SCK↓→SOT delay time
tSLOVE
SIN→SCK↑
setup time
tIVSHE
SCK↑→SIN hold time
tSHIXE
SCK falling time
SCK rising time
tF
tR
Pin Name Conditions
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx,
SOTx
SCKx
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
Internal shift
clock
operation
External
shift clock
operation
VCC < 4.5 V
Min
Max
4tCYCP
-
VCC ≥ 4.5 V
Min
Max
4tCYCP
-
Unit
ns
- 30
+ 30
- 20
+ 20
ns
50
-
30
-
ns
0
-
0
-
ns
2tCYCP - 30
-
2tCYCP - 30
-
ns
2tCYCP - 10
tCYCP + 10
-
2tCYCP - 10
tCYCP + 10
-
ns
ns
-
50
-
30
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
Notes:
−
The above characteristics apply to CLK synchronous mode.
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
These characteristics only guarantee the same relocate port number.
For example, the combination of SCLKx_0 and SOTx_1 is not guaranteed.
−
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 108 of 160
S6E2H4 Series
tSCYC
VOH
SCK
tSOVHI
SOT
tSLOVI
VOH
VOL
VOH
VOL
tSHIXI
tIVSHI
VIH
VIL
SIN
VOH
VOL
VIH
VIL
MS bit = 0
tSHSL
tR
SCK
VIL
VIH
tSLSH
VIH
VIL
tF
VIL
VIH
tSLOVE
SOT
VOH
VOL
VOH
VOL
tIVSHE
SIN
tSHIXE
VIH
VIL
VIH
VIL
MS bit = 1
Document Number: 001-98941 Rev.*C
Page 109 of 160
S6E2H4 Series
When Using Synchronous Serial Chip Select (SPI = 1, SCINV = 0, MS=0, CSLVL=1)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
SCS↓→SCK↓setup time
tCSSI
SCK↑→SCS↑ hold time
tCSHI
SCS deselect time
tCSDI
SCS↓→SCK↓setup time
tCSSE
SCK↑→SCS↑ hold time
tCSHE
SCS deselect time
tCSDE
SCS↓→SUT delay time
tDSE
Conditions
Internal shift
clock
operation
External shift
clock
operation
VCC ≥ 4.5 V
VCC < 4.5 V
Min
Min
(*1)-50
(*1)+0
(*1)-50
(*1)+0
ns
(*2)+0
(*3)-50
+5tCYCP
3tCYCP+30
(*2)+50
(*3)+50
+5tCYCP
-
(*2)+0
(*3)-50
+5tCYCP
3tCYCP+30
(*2)+50
(*3)+50
+5tCYCP
-
ns
0
-
0
-
ns
3tCYCP+30
-
3tCYCP+30
-
ns
-
40
-
40
ns
-
0
-
ns
SCS↑→SUT delay time
tDEE
0
(*1): CSSU bit value×serial chip select timing operating clock cycle [ns]
Max
Unit
Max
ns
ns
(*2): CSHD bit value×serial chip select timing operating clock cycle [ns]
(*3): CSDS bit value×serial chip select timing operating clock cycle [ns]
Notes:
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
About CSSU, CSHD, CSDS, serial chip select timing operating clock, see FM4 Family Peripheral Manual Main part(MN70900001).
−
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 110 of 160
S6E2H4 Series
SCS output
tCSDI
tCSSI
tCSHI
SCK output
SOT
(SPI=0)
SOT
(SPI=1)
SCS input
tCSDE
tCSSE
tCSHE
SCK input
tDEE
SOT
(SPI=0)
tDSE
SOT
(SPI=1)
Document Number: 001-98941 Rev.*C
Page 111 of 160
S6E2H4 Series
When Using Synchronous Serial Chip Select (SPI = 1, SCINV = 1, MS=0, CSLVL=1)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
SCS↓→SCK↑setup time
tCSSI
SCK↓→SCS↑ hold time
tCSHI
SCS deselect time
tCSDI
SCS↓→SCK↑setup time
tCSSE
SCK↓→SCS↑ hold time
tCSHE
SCS deselect time
tCSDE
SCS↓→SOT delay time
tDSE
Conditions
Internal shift
clock
operation
External shift
clock
operation
VCC ≥ 4.5 V
VCC < 4.5 V
Min
Min
(*1)-50
(*1)+0
(*1)-50
(*1)+0
ns
(*2)+0
(*3)-50
+5tCYCP
3tCYCP+30
(*2)+50
(*3)+50
+5tCYCP
-
(*2)+0
(*3)-50
+5tCYCP
3tCYCP+30
(*2)+50
(*3)+50
+5tCYCP
-
ns
0
-
0
-
ns
3tCYCP+30
-
3tCYCP+30
-
ns
-
40
-
40
ns
-
0
-
ns
SCS↑→SOT delay time
tDEE
0
(*1): CSSU bit value×serial chip select timing operating clock cycle [ns]
Max
Unit
Max
ns
ns
(*2): CSHD bit value×serial chip select timing operating clock cycle [ns]
(*3): CSDS bit value×serial chip select timing operating clock cycle [ns]
Notes:
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
About CSSU, CSHD, CSDS, serial chip select timing operating clock, see FM4 Family Peripheral Manual Main part(MN70900001).
−
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 112 of 160
S6E2H4 Series
SCS output
tCSDI
tCSSI
tCSHI
SCK output
SOT
(SPI=0)
SOT
(SPI=1)
SCS input
tCSDE
tCSSE
tCSHE
SCK input
tDEE
SOT
(SPI=0)
tDSE
SOT
(SPI=1)
Document Number: 001-98941 Rev.*C
Page 113 of 160
S6E2H4 Series
When Using Synchronous Serial Chip Select (SPI = 1, SCINV = 0, MS=0, CSLVL=0)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
SCS↑→SCK↓setup time
tCSSI
SCK↑→SCS↓ hold time
tCSHI
SCS deselect time
tCSDI
SCS↑→SCK↓setup time
tCSSE
SCK↑→SCS↓ hold time
tCSHE
SCS deselect time
tCSDE
SCS↑→SOT delay time
tDSE
Conditions
Internal shift
clock
operation
External shift
clock
operation
VCC ≥ 4.5 V
VCC < 4.5 V
Unit
Min
Max
Min
Max
(*1)-50
(*1)+0
(*1)-50
(*1)+0
ns
(*2)+0
(*3)-50
+5tCYCP
3tCYCP+30
(*2)+50
(*3)+50
+5tCYCP
-
(*2)+0
(*3)-50
+5tCYCP
3tCYCP+30
(*2)+50
(*3)+50
+5tCYCP
-
ns
ns
ns
0
-
0
-
ns
3tCYCP+30
-
3tCYCP+30
-
ns
-
40
-
40
ns
-
0
-
ns
SCS↓→SOT delay time
tDEE
0
(*1): CSSU bit value×serial chip select timing operating clock cycle [ns]
(*2): CSHD bit value×serial chip select timing operating clock cycle [ns]
(*3): CSDS bit value×serial chip select timing operating clock cycle [ns]
Notes:
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
About CSSU, CSHD, CSDS, serial chip select timing operating clock, see FM4 Family Peripheral Manual Main part(MN70900001).
−
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 114 of 160
S6E2H4 Series
tCSDI
SCS output
tCSSI
tCSHI
SCK output
SOT
(SPI=0)
SOT
(SPI=1)
tCSDE
SCS input
tCSSE
tCSHE
SCK input
tDEE
SOT
(SPI=0)
tDSE
SOT
(SPI=1)
Document Number: 001-98941 Rev.*C
Page 115 of 160
S6E2H4 Series
When Using Synchronous Serial Chip Select (SPI = 1, SCINV = 1, MS=0, CSLVL=0)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
SCS↑→SCK↑setup time
tCSSI
SCK↓→SCS↓ hold time
tCSHI
SCS deselect time
tCSDI
SCS↑→SCK↑setup time
tCSSE
SCK↓→SCS↓ hold time
tCSHE
SCS deselect time
tCSDE
SCS↑→SOT delay time
tDSE
Conditions
Internal shift
clock
operation
External shift
clock
operation
VCC ≥ 4.5 V
VCC < 4.5 V
Unit
Min
Max
Min
Max
(*1)-50
(*1)+0
(*1)-50
(*1)+0
ns
(*2)+0
(*3)-50
+5tCYCP
3tCYCP+30
(*2)+50
(*3)+50
+5tCYCP
-
(*2)+0
(*3)-50
+5tCYCP
3tCYCP+30
(*2)+50
(*3)+50
+5tCYCP
-
ns
ns
ns
0
-
0
-
ns
3tCYCP+30
-
3tCYCP+30
-
ns
-
40
-
40
ns
-
0
-
ns
SCS↓→SOT delay time
tDEE
0
(*1): CSSU bit value×serial chip select timing operating clock cycle [ns]
(*2): CSHD bit value×serial chip select timing operating clock cycle [ns]
(*3): CSDS bit value×serial chip select timing operating clock cycle [ns]
Notes:
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
About CSSU, CSHD, CSDS, serial chip select timing operating clock, see FM4 Family Peripheral Manual Main part(MN70900001).
−
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 116 of 160
S6E2H4 Series
tCSDI
SCS output
tCSSI
tCSHI
SCK output
SOT
(SPI=0)
SOT
(SPI=1)
tCSDE
SCS input
tCSSE
tCSHE
SCK input
tDEE
SOT
(SPI=0)
tDSE
SOT
(SPI=1)
Document Number: 001-98941 Rev.*C
Page 117 of 160
S6E2H4 Series
High-speed Synchronous Serial (SPI = 0, SCINV = 0)
(VCC = 2.7V to 5.5V, VSS = 0V)
VCC < 4.5 V
VCC ≥ 4.5 V
Min
Max
Min
Max
SCKx
4tCYCP
-
4tCYCP
-
ns
tSLOVI
SCKx,
SOTx
-10
+10
-10
+10
ns
SIN→SCK↑
setup time
tIVSHI
SCKx,
SINx
-
12.5
-
ns
SCK↑→SIN hold time
tSHIXI
SCKx,
SINx
5
-
5
-
ns
Serial clock L pulse width
tSLSH
SCKx
2tCYCP – 5
-
2tCYCP – 5
-
ns
Serial clock H pulse width
tSHSL
SCKx
tCYCP + 10
-
tCYCP + 10
-
ns
SCK↓→SOT delay time
tSLOVE
SCKx,
SOTx
-
15
-
15
ns
SIN→SCK↑
setup time
tIVSHE
SCKx,
SINx
5
-
5
-
ns
SCK↑→SIN hold time
tSHIXE
5
-
5
-
ns
Parameter
Symbol
Pin Name
Serial clock cycle time
tSCYC
SCK↓→SOT delay time
Conditions
Internal shift
clock operation
14
12.5*
External shift
clock operation
SCKx,
SINx
Unit
SCK falling time
tF
SCKx
-
5
-
5
ns
SCK rising time
tR
SCKx
-
5
-
5
ns
Notes:
−
The above characteristics apply to CLK synchronous mode.
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
−
These characteristics only guarantee the following pins.
−
−
Chip select:
No chip select: SIN4_1, SOT4_1, SCK4_1
SIN6_1, SOT6_1, SCK6_1, SCS6_1
When the external load capacitance CL = 30 pF. (For *, when CL = 10 pF)
Document Number: 001-98941 Rev.*C
Page 118 of 160
S6E2H4 Series
tSCYC
VOH
SCK
VOL
VOL
tSLOVI
VOH
VOL
SOT
tIVSHI
VIH
VIL
SIN
tSHIXI
VIH
VIL
MS bit = 0
tSLSH
SCK
VIH
tF
VIL
tSHSL
VIL
SIN
VIH
tR
tSLOVE
SOT
VIH
VOH
VOL
tIVSHE
VIH
VIL
tSHIXE
VIH
VIL
MS bit = 1
Document Number: 001-98941 Rev.*C
Page 119 of 160
S6E2H4 Series
High-speed Synchronous Serial (SPI = 0, SCINV = 1)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Pin Name
Serial clock cycle time
tSCYC
SCKx
SCK↑→SOT delay time
tSHOVI
SCKx,
SOTx
VCC < 4.5 V
VCC ≥ 4.5 V
Min
Max
Min
Max
4tCYCP
-
4tCYCP
-
ns
-10
+10
-10
+10
ns
-
12.5
-
ns
Conditions
Internal shift
clock operation
14
Unit
SIN→SCK↓
setup time
tIVSLI
SCKx,
SINx
SCK↓→SIN hold time
tSLIXI
SCKx,
SINx
5
-
5
-
ns
Serial clock L pulse width
tSLSH
SCKx
2tCYCP – 5
-
2tCYCP – 5
-
ns
Serial clock H pulse width
tSHSL
SCKx
tCYCP + 10
-
tCYCP + 10
-
ns
SCK↑→SOT delay time
tSHOVE
SCKx,
SOTx
-
15
-
15
ns
5
-
5
-
ns
12.5*
External shift
clock operation
SIN→SCK↓
setup time
tIVSLE
SCKx,
SINx
SCK↓→SIN hold time
tSLIXE
SCKx,
SINx
5
-
5
-
ns
SCK falling time
tF
SCKx
-
5
-
5
ns
SCK rising time
tR
SCKx
-
5
-
5
ns
Notes:
−
The above characteristics apply to CLK synchronous mode.
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
−
−
−
These characteristics only guarantee the following pins.
No chip select: SIN4_1, SOT4_1, SCK4_1
Chip select:
SIN6_1, SOT6_1, SCK6_1, SCS6_1
When the external load capacitance CL = 30 pF. (For *, when CL = 10 pF)
Document Number: 001-98941 Rev.*C
Page 120 of 160
S6E2H4 Series
tSCYC
VOH
SCK
VOH
VOL
tSHOVI
VOH
VOL
SOT
tIVSLI
VIH
VIL
SIN
tSLIXI
VIH
VIL
MS bit = 0
tSHSL
SCK
VIH
VIL
tR
tSLSH
VIH
SIN
VIL
tF
tSHOVE
SOT
VIL
VOH
VOL
tIVSLE
VIH
VIL
tSLIXE
VIH
VIL
MS bit = 1
Document Number: 001-98941 Rev.*C
Page 121 of 160
S6E2H4 Series
High-speed Synchronous Serial (SPI = 1, SCINV = 0)
(VCC = 2.7V to 5.5V, VSS = 0V)
VCC < 4.5 V
VCC ≥ 4.5 V
Min
Max
Min
Max
SCKx
4tCYCP
-
4tCYCP
-
ns
tSHOVI
SCKx,
SOTx
-10
+10
-10
+10
ns
SIN→SCK↓
setup time
tIVSLI
SCKx,
SINx
-
12.5
-
ns
SCK↓→SIN hold time
tSLIXI
SCKx,
SINx
5
-
5
-
ns
SOT→SCK↓ delay time
tSOVLI
SCKx,
SOTx
2tCYCP – 10
-
2tCYCP – 10
-
ns
Serial clock L pulse width
tSLSH
SCKx
2tCYCP – 5
-
2tCYCP – 5
-
ns
Serial clock H pulse width
tSHSL
SCKx
tCYCP + 10
-
tCYCP + 10
-
ns
tSHOVE
SCKx,
SOTx
-
15
-
15
ns
5
-
5
-
ns
Parameter
Symbol
Pin Name
Serial clock cycle time
tSCYC
SCK↑→SOT delay time
SCK↑→SOT delay time
Conditions
Internal shift
clock operation
14
12.5*
Unit
External shift
clock operation
SIN→SCK↓
setup time
tIVSLE
SCKx,
SINx
SCK↓→SIN hold time
tSLIXE
SCKx,
SINx
5
-
5
-
ns
SCK falling time
tF
SCKx
-
5
-
5
ns
SCK rising time
tR
SCKx
-
5
-
5
ns
Notes:
−
The above characteristics apply to CLK synchronous mode.
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
−
−
These characteristics only guarantee the following pins.
−
When the external load capacitance CL = 30 pF. (For *, when CL = 10 pF)
No chip select: SIN4_1, SOT4_1, SCK4_1
Chip select:
SIN6_1, SOT6_1, SCK6_1, SCS6_1
Document Number: 001-98941 Rev.*C
Page 122 of 160
S6E2H4 Series
tSCYC
VOH
VOL
SCK
SOT
VOH
VOL
VOH
VOL
tIVSLI
tSLIXI
VIH
VIL
SIN
VOL
tSHOVI
tSOVLI
VIH
VIL
MS bit = 0
tSLSH
VIH
SCK
VIL
tSHSL
VIH
VIL
tF
*V
tR
VIH
tSHOVE
VOH
VOL
OH
SOT
VOL
tIVSLE
SIN
tSLIXE
VIH
VIL
VIH
VIL
MS bit = 1
*: Changes when writing to TDR register
Document Number: 001-98941 Rev.*C
Page 123 of 160
S6E2H4 Series
High-speed Synchronous Serial (SPI = 1, SCINV = 1)
(VCC = 2.7V to 5.5V, VSS = 0V)
VCC < 4.5 V
VCC ≥ 4.5 V
Min
Max
Min
Max
SCKx
4tCYCP
-
4tCYCP
-
ns
tSLOVI
SCKx,
SOTx
-10
+10
-10
+10
ns
SIN→SCK↑
setup time
tIVSHI
SCKx,
SINx
-
12.5
-
ns
SCK↑→SIN hold time
tSHIXI
SCKx,
SINx
5
-
5
-
ns
SOT→SCK↑ delay time
tSOVHI
SCKx,
SOTx
2tCYCP – 10
-
2tCYCP – 10
-
ns
Serial clock L pulse width
tSLSH
SCKx
2tCYCP – 5
-
2tCYCP – 5
-
ns
Serial clock H pulse width
tSHSL
SCKx
tCYCP + 10
-
tCYCP + 10
-
ns
SCK↓→SOT delay time
tSLOVE
SCKx,
SOTx
-
15
-
15
ns
SIN→SCK↑
setup time
tIVSHE
SCKx,
SINx
5
-
5
-
ns
SCK↑→SIN hold time
tSHIXE
SCKx,
SINx
5
-
5
-
ns
SCK falling time
tF
SCKx
-
5
-
5
ns
SCK rising time
tR
SCKx
-
5
-
5
ns
Parameter
Symbol
Pin Name
Internal shift clock
operation
tSCYC
SCK↓→SOT delay time
Conditions
Internal shift
clock
operation
External shift
clock
operation
14
12.5*
Unit
Notes:
−
The above characteristics apply to CLK synchronous mode.
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
−
−
−
These characteristics only guarantee the following pins.
No chip select: SIN4_1, SOT4_1, SCK4_1
Chip select:
SIN6_1, SOT6_1, SCK6_1, SCS6_1
When the external load capacitance CL = 30 pF. (For *, when CL = 10 pF)
Document Number: 001-98941 Rev.*C
Page 124 of 160
S6E2H4 Series
tSCYC
VOH
SCK
tSOVHI
SOT
tSLOVI
VOH
VOL
VOH
VOL
tSHIXI
tIVSHI
VIH
VIL
SIN
VOH
VOL
VIH
VIL
MS bit = 0
tSHSL
tR
SCK
VIL
VIH
tSLSH
VIH
VIL
tF
VIL
VIH
tSLOVE
SOT
VOH
VOL
VOH
VOL
tIVSHE
SIN
tSHIXE
VIH
VIL
VIH
VIL
MS bit = 1
Document Number: 001-98941 Rev.*C
Page 125 of 160
S6E2H4 Series
When Using High-speed Synchronous Serial Chip Select (SPI = 1, SCINV = 0, MS=0, CSLVL=1)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
SCS↓→SCK↓setup time
tCSSI
SCK↑→SCS↑ hold time
tCSHI
SCS deselect time
tCSDI
SCS↓→SCK↓setup time
tCSSE
SCK↑→SCS↑ hold time
tCSHE
SCS deselect time
tCSDE
SCS↓→SOT delay time
tDSE
Conditions
Internal shift
clock operation
External shift
clock operation
VCC ≥ 4.5 V
VCC < 4.5 V
Min
Min
(*1)-20
(*1)+0
(*1)-20
(*1)+0
ns
(*2)+0
(*3)-20
+5tCYCP
3tCYCP+15
(*2)+20
(*3)+20
+5tCYCP
-
(*2)+0
(*3)-20
+5tCYCP
3tCYCP+15
(*2)+20
(*3)+20
+5tCYCP
-
ns
0
-
0
-
ns
3tCYCP+15
-
3tCYCP+15
-
ns
-
25
-
25
ns
-
0
-
ns
SCS↑→SOT delay time
tDEE
0
(*1): CSSU bit value×serial chip select timing operating clock cycle [ns]
Max
Unit
Max
ns
ns
(*2): CSHD bit value×serial chip select timing operating clock cycle [ns]
(*3): CSDS bit value×serial chip select timing operating clock cycle [ns]
Notes:
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
−
About CSSU, CSHD, CSDS, serial chip select timing operating clock, see FM4 Family Peripheral Manual.
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 126 of 160
S6E2H4 Series
SCS output
tCSDI
tCSSI
tCSHI
SCK output
SOT
(SPI=0)
SOT
(SPI=1)
SCS input
tCSDE
tCSSE
tCSHE
SCK input
tDEE
SOT
(SPI=0)
tDSE
SOT
(SPI=1)
Document Number: 001-98941 Rev.*C
Page 127 of 160
S6E2H4 Series
When Using High-speed Synchronous Serial Chip Select (SPI = 1, SCINV = 1, MS=0, CSLVL=1)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
SCS↓→SCK↑setup time
tCSSI
SCK↓→SCS↑ hold time
tCSHI
SCS deselect time
tCSDI
SCS↓→SCK↑setup time
tCSSE
SCK↓→SCS↑ hold time
tCSHE
SCS deselect time
tCSDE
SCS↓→SOT delay time
tDSE
Conditions
Internal shift
clock
operation
External shift
clock
operation
VCC ≥ 4.5 V
VCC < 4.5 V
Min
Min
(*1)-20
(*1)+0
(*1)-20
(*1)+0
ns
(*2)+0
(*3)-20
+5tCYCP
3tCYCP+15
(*2)+20
(*3)+20
+5tCYCP
-
(*2)+0
(*3)-20
+5tCYCP
3tCYCP+15
(*2)+20
(*3)+20
+5tCYCP
-
ns
0
-
0
-
ns
3tCYCP+15
-
3tCYCP+15
-
ns
-
25
-
25
ns
-
0
-
ns
SCS↑→SOT delay time
tDEE
0
(*1): CSSU bit value×serial chip select timing operating clock cycle [ns]
Max
Unit
Max
ns
ns
(*2): CSHD bit value×serial chip select timing operating clock cycle [ns]
(*3): CSDS bit value×serial chip select timing operating clock cycle [ns]
Notes:
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
About CSSU, CSHD, CSDS, serial chip select timing operating clock, see FM4 Family Peripheral Manual Main part(MN70900001).
−
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 128 of 160
S6E2H4 Series
SCS output
tCSDI
tCSSI
tCSHI
SCK output
SOT
(SPI=0)
SOT
(SPI=1)
SCS input
tCSDE
tCSSE
tCSHE
SCK input
tDEE
SOT
(SPI=0)
tDSE
SOT
(SPI=1)
Document Number: 001-98941 Rev.*C
Page 129 of 160
S6E2H4 Series
When Using High-speed Synchronous Serial Chip Select (SPI = 1, SCINV = 0, MS=0, CSLVL=0)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
SCS↑→SCK↓setup time
tCSSI
SCK↑→SCS↓ hold time
tCSHI
SCS deselect time
tCSDI
SCS↑→SCK↓setup time
tCSSE
SCK↑→SCS↓ hold time
tCSHE
SCS deselect time
tCSDE
SCS↑→SOT delay time
tDSE
Conditions
Internal shift
clock operation
External shift
clock operation
VCC ≥ 4.5 V
VCC < 4.5 V
Unit
Min
Max
Min
Max
(*1)-20
(*1)+0
(*1)-20
(*1)+0
ns
(*2)+0
(*3)-20
+5tCYCP
3tCYCP+15
(*2)+20
(*3)+20
+5tCYCP
-
(*2)+0
(*3)-20
+5tCYCP
3tCYCP+15
(*2)+20
(*3)+20
+5tCYCP
-
ns
ns
ns
0
-
0
-
ns
3tCYCP+15
-
3tCYCP+15
-
ns
-
25
-
25
ns
-
0
-
ns
SCS↓→SOT delay time
tDEE
0
(*1): CSSU bit value×serial chip select timing operating clock cycle [ns]
(*2): CSHD bit value×serial chip select timing operating clock cycle [ns]
(*3): CSDS bit value×serial chip select timing operating clock cycle [ns]
Notes:
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
About CSSU, CSHD, CSDS, serial chip select timing operating clock, see FM4 Family Peripheral Manual Main part(MN70900001).
−
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 130 of 160
S6E2H4 Series
tCSDI
SCS output
tCSSI
tCSHI
SCK output
SOT
(SPI=0)
SOT
(SPI=1)
tCSDE
SCS input
tCSSE
tCSHE
SCK input
tDEE
SOT
(SPI=0)
tDSE
SOT
(SPI=1)
Document Number: 001-98941 Rev.*C
Page 131 of 160
S6E2H4 Series
When Using High-speed Synchronous Serial Chip Select (SPI = 1, SCINV = 1, MS=0, CSLVL=0)
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
SCS↑→SCK↑setup time
tCSSI
SCK↓→SCS↓ hold time
tCSHI
SCS deselect time
tCSDI
SCS↑→SCK↑setup time
tCSSE
SCK↓→SCS↓ hold time
tCSHE
SCS deselect time
tCSDE
SCS↑→SOT delay time
tDSE
Conditions
Internal shift
clock
operation
External shift
clock
operation
VCC ≥ 4.5 V
VCC < 4.5 V
Unit
Min
Max
Min
Max
(*1)-20
(*1)+0
(*1)-20
(*1)+0
ns
(*2)+0
(*3)-20
+5tCYCP
3tCYCP+15
(*2)+20
(*3)+20
+5tCYCP
-
(*2)+0
(*3)-20
+5tCYCP
3tCYCP+15
(*2)+20
(*3)+20
+5tCYCP
-
ns
ns
ns
0
-
0
-
ns
3tCYCP+15
-
3tCYCP+15
-
ns
-
25
-
25
ns
-
0
-
ns
SCS↓→SOT delay time
tDEE
0
(*1): CSSU bit value×serial chip select timing operating clock cycle [ns]
(*2): CSHD bit value×serial chip select timing operating clock cycle [ns]
(*3): CSDS bit value×serial chip select timing operating clock cycle [ns]
Notes:
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which multi-function serial is connected to, see 8. Block Diagram in this data sheet.
−
About CSSU, CSHD, CSDS, serial chip select timing operating clock, see FM4 Family Peripheral Manual Main part(MN70900001).
−
When the external load capacitance CL = 30 pF.
Document Number: 001-98941 Rev.*C
Page 132 of 160
S6E2H4 Series
tCSDI
SCS output
tCSSI
tCSHI
SCK output
SOT
(SPI=0)
SOT
(SPI=1)
tCSDE
SCS input
tCSSE
tCSHE
SCK input
tDEE
SOT
(SPI=0)
tDSE
SOT
(SPI=1)
Document Number: 001-98941 Rev.*C
Page 133 of 160
S6E2H4 Series
External Clock (EXT = 1): when in Asynchronous Mode Only
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Serial clock L pulse width
Serial clock H pulse width
SCK falling time
SCK rising time
tSLSH
tSHSL
tF
tR
Condition
CL = 30 pF
tR
SCK
Document Number: 001-98941 Rev.*C
Value
Min
tCYCP + 10
tCYCP + 10
-
tSHSL
V IL
VIH
Unit
Max
5
5
ns
ns
ns
ns
tF
tSLSH
VIH
V IL
Remarks
V IL
VIH
Page 134 of 160
S6E2H4 Series
12.4.12 External Input Timing
(VCC = 2.7V to 5.5V, VSS = 0V)
Value
Parameter
Symbol
Pin Name
Conditions
Min
Max
2tCYCP*1
-
Unit
ADTG
Remarks
A/D converter trigger input
-
ns
FRCKx
Free-run timer input clock
ICxx
Input capture
DTTIxX
2tCYCP*1
ns
Waveform generator
2tCYCP + 100*1
ns
INT00 to INT15,
External interrupt,
NMIX
NMI
500*2
ns
WKUPx
500*3
ns
Deep standby wake up
*1: tCYCP indicates the APB bus clock cycle time except stop when in Stop mode, in timer mode.
About the APB bus number which the A/D converter, Multi-function Timer, External interrupt are connected to, see 8. Block
Diagram in this data sheet.
Input pulse
width
tINH,
tINL
*2: When in Stop mode, in timer mode.
*3: When in deep standby RTC mode, in deep standby Stop mode.
Document Number: 001-98941 Rev.*C
Page 135 of 160
S6E2H4 Series
12.4.13 Quadrature Position/Revolution Counter Timing
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
Value
Conditions
Min
Max
Unit
AIN pin H width
tAHL
AIN pin L width
tALL
BIN pin H width
tBHL
BIN pin L width
tBLL
BIN rising time from
tAUBU
PC_Mode2 or PC_Mode3
AIN pin H level
AIN falling time from
tBUAD
PC_Mode2 or PC_Mode3
BIN pin H level
BIN falling time from
tADBD
PC_Mode2 or PC_Mode3
AIN pin L level
AIN rising time from
tBDAU
PC_Mode2 or PC_Mode3
BIN pin L level
AIN rising time from
2tCYCP*
ns
tBUAU
PC_Mode2 or PC_Mode3
BIN pin H level
BIN falling time from
tAUBD
PC_Mode2 or PC_Mode3
AIN pin H level
AIN falling time from
tBDAD
PC_Mode2 or PC_Mode3
BIN pin L level
BIN rising time from
tADBU
PC_Mode2 or PC_Mode3
AIN pin L level
ZIN pin H width
tZHL
QCR:CGSC="0"
ZIN pin L width
tZLL
QCR:CGSC="0"
AIN/BIN rising and falling time from
tZABE
QCR:CGSC="1"
determined ZIN level
Determined ZIN level from AIN/BIN
tABEZ
QCR:CGSC="1"
rising and falling time
*: tCYCP indicates the APB bus clock cycle time except stop when in Stop mode, in timer mode.
About the APB bus number which Quadrature Position/Revolution Counter is connected to, see "8. Block Diagram" in this data
sheet.
tALL
tAHL
AIN
tAUBU
tADBD
tBUAD
tBDAU
BIN
tBHL
Document Number: 001-98941 Rev.*C
tBLL
Page 136 of 160
S6E2H4 Series
tBLL
tBHL
BIN
tBUAU
tBDAD
tAUBD
tADBU
AIN
tAHL
tALL
ZIN
ZIN
AIN/BIN
Document Number: 001-98941 Rev.*C
Page 137 of 160
S6E2H4 Series
12.4.14 I2C Timing
Standard-mode,Fast-mode
(VCC = 2.7V to 5.5V, VSS = 0V)
Parameter
Symbol
SCL clock frequency
(Repeated) Start condition
hold time
SDA ↓ → SCL ↓
SCL clock L width
SCL clock H width
(Repeated) Start condition
setup time
SCL ↑ → SDA ↓
Data hold time
SCL ↓ → SDA ↓ ↑
Data setup time
SDA ↓ ↑ → SCL ↑
STOP condition setup time
SCL ↑ → SDA ↑
Bus free time between
Stop condition and
Start condition
fSCL
Noise filter
Conditions
Standard-mode
Min
Max
0
100
Fast-mode
Min
Max
0
400
Unit
kHz
tHDSTA
4.0
-
0.6
-
μs
tLOW
tHIGH
4.7
4.0
-
1.3
0.6
-
μs
μs
4.7
-
0.6
-
μs
0
3.45*2
0
0.9*3
μs
tSUDAT
250
-
100
-
ns
tSUSTO
4.0
-
0.6
-
μs
tBUF
4.7
-
1.3
-
μs
2tCYCP*4
-
2tCYCP*4
-
ns
4tCYCP*4
-
4tCYCP*4
-
ns
6tCYCP*4
-
6tCYCP*4
-
ns
8tCYCP*4
-
8tCYCP*4
-
ns
10tCYCP*4
-
10tCYCP*4
-
ns
12tCYCP*4
-
12tCYCP*4
-
ns
14tCYCP*4
-
14tCYCP*4
-
ns
16tCYCP*4
-
16tCYCP*4
-
ns
tSUSTA
tHDDAT
tSP
CL = 30 pF,
R = (Vp/IOL)*1
2 MHz ≤
tCYCP