0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
STK14CA8-NF25ITR

STK14CA8-NF25ITR

  • 厂商:

    EUPEC(英飞凌)

  • 封装:

    SOIC32

  • 描述:

    IC NVSRAM 1MBIT PARALLEL 32SOIC

  • 数据手册
  • 价格&库存
STK14CA8-NF25ITR 数据手册
STK14CA8 128Kx8 AutoStore nvSRAM Features Description ■ 25, 35, 45 ns Read Access and Read/Write Cycle Time The Cypress STK14CA8 is a 1 Mb fast static RAM with a nonvolatile QuantumTrap storage element included with each memory cell. This SRAM provides fast access and cycle times, ease of use, and unlimited read and write endurance of a normal SRAM. ■ Unlimited Read/Write Endurance ■ Automatic Nonvolatile STORE on Power Loss ■ Nonvolatile STORE Under Hardware or Software Control ■ Automatic RECALL to SRAM on Power Up ■ Unlimited RECALL Cycles ■ 200K STORE Cycles ■ 20-Year Nonvolatile Data Retention ■ Single 3.0V + 20%, -10% Operation ■ Commercial and Industrial Temperatures ■ Small Footprint SOIC and SSOP Packages (RoHS Compliant) es ig ns Data transfers automatically to the nonvolatile storage cells when power loss is detected (the STORE operation). On power up, data is automatically restored to the SRAM (the RECALL operation). Both STORE and RECALL operations are also available under software control. rN fo Logic Block Diagram Quantum Trap 1024 X 1024 d de en VCAP STORE/ RECALL CONTROL RECALL HSB m ec INPUT BUFFERS R ot N STORE STATIC RAM ARRAY 1024 X 1024 VCC POWER CONTROL om ROW DECODER A5 A6 A7 A8 A9 A12 A13 A14 A15 A16 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 ew D The Cypress nvSRAM is the first monolithic nonvolatile memory to offer unlimited writes and reads. It is the highest performing and most reliable nonvolatile memory available. SOFTWARE DETECT A15 – A0 COLUMN I/O COLUMN DEC A0 A1 A2 A3 A4 A10 A11 G E W Cypress Semiconductor Corporation Document Number: 001-51592 Rev. *A • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised December 02, 2009 [+] Feedback STK14CA8 Contents SRAM READ ............................................................... 13 SRAM WRITE ............................................................. 13 AutoStore Operation.................................................... 13 Hardware STORE (HSB) Operation............................ 13 Hardware RECALL (Power Up)................................... 13 Software STORE......................................................... 14 Software RECALL ....................................................... 14 Data Protection............................................................ 14 Noise Considerations .................................................. 14 Best Practices ............................................................. 14 Low Average Active Power ......................................... 15 Preventing AutoStore....................................................... 15 STK14CA8-R F 45 ITR ...................................................... 16 Package Diagrams............................................................ 17 Document History Page .................................................... 18 Sales, Solutions, and Legal Information ........................ 18 Worldwide Sales and Design Support......................... 18 Products ...................................................................... 18 N ot R ec om m en de d fo rN ew D es ig ns Features............................................................................... 1 Description.......................................................................... 1 Logic Block Diagram.......................................................... 1 Contents .............................................................................. 2 Pinouts ................................................................................ 3 Pin Descriptions ................................................................. 3 Absolute Maximum Ratings .............................................. 4 DC Characteristics ............................................................. 4 Capacitance ........................................................................ 6 SRAM READ Cycles #1 and #2 .................................... 7 SRAM WRITE Cycles #1 and #2................................... 8 AutoStore/POWER UP RECALL ........................................ 9 Software Controlled STORE/RECALL Cycle........... 10 Hardware STORE Cycle ................................................... 11 Soft Sequence Commands ............................................... 11 Mode Selection ................................................................. 12 nvSRAM Operation........................................................... 13 nvSRAM ...................................................................... 13 Document Number: 001-51592 Rev. *A Page 2 of 17 [+] Feedback STK14CA8 Pinouts Figure 1. 48-Pin SSOP Figure 2. 32-Pin SOIC 1 48 VCC VCAP 1 32 VCC A16 A14 2 47 A15 A16 2 31 A15 3 46 HSB 30 4 A6 43 5 A5 7 42 6 27 HSB W A13 A8 NC 8 41 A4 9 40 A11 A7 A6 A5 A4 29 28 6 W A13 A8 4 5 45 44 A14 A12 3 A12 A7 NC 10 39 NC 9 NC 11 38 NC A3 A2 7 8 es 10 NC 12 37 NC A1 VSS 13 36 VSS A0 NC NC 14 35 NC D A9 NC ig ns VCAP 15 34 DQ0 16 33 NC DQ6 A3 17 32 G A2 18 31 A10 A1 19 30 E A0 DQ1 DQ2 20 29 DQ7 21 28 DQ5 22 23 27 DQ4 NC 26 DQ3 NC 24 25 VCC 26 25 24 23 A9 A11 G A10 22 12 21 DQ0 13 20 DQ1 DQ2 14 19 DQ6 DQ5 15 18 DQ4 VSS 16 17 DQ3 E DQ7 rN ew 11 m en de d fo Figure 3. Relative PCB Area Usage[1] om Pin Descriptions Pin Name I/O A16-A0 Input DQ7-DQ0 I/O E Input Chip Enable: The active low E input selects the device. W Input Write Enable: The active low W allows to write the data on the DQ pins to the address location latched by the falling edge of E. ec Address: The 17 address inputs select one of 131,072 bytes in the nvSRAM array. Data: Bi-directional 8-bit data bus for accessing the nvSRAM. R ot N G Description Input Output Enable: The active low G input enables the data output buffers during read cycles. De-asserting G high causes the DQ pins to tri-state. VCC Power Supply Power: 3.0V, +20%, -10%. HSB I/O Hardware Store Busy: When low this output indicates a Store is in progress. When pulled low external to the chip, it initiates a nonvolatile STORE operation. A weak pull up resistor keeps this pin high if not connected. (Connection is optional). VCAP Power Supply AutoStore Capacitor: Supplies power to nvSRAM during power loss to store data from SRAM to nonvolatile storage elements. VSS Power Supply Ground. NC No Connect Unlabeled pins have no internal connections. Note 1. See Package Diagrams on page 16 for detailed package size specifications. Document Number: 001-51592 Rev. *A Page 3 of 17 [+] Feedback STK14CA8 Absolute Maximum Ratings NF (SOP-32) PACKAGE THERMAL CHARACTERISTICS θjc 5.4 C/W; θja 44.3 [0fpm], 37.9 [200fpm], 35.1 C/W [500fpm]. Voltage on Input Relative to Ground.................–0.5V to 4.1V RF (SSOP-48) PACKAGE THERMAL CHARACTERISTICS Voltage on Input Relative to VSS ...........–0.5V to (VCC + 0.5V) θjc 6.2 C/W; θja 51.1 [0fpm], 44.7 [200fpm], 41.8 C/W [500fpm]. Voltage on DQ0-7 or HSB ......................–0.5V to (VCC + 0.5V) Temperature under Bias ............................... –55°C to 125°C Note: Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Junction Temperature ................................... –55°C to 140°C Storage Temperature .................................... –65°C to 150°C Power Dissipation............................................................. 1W ig ns DC Output Current (1 output at a time, 1s duration).... 15 mA es DC Characteristics Commercial Parameter Min Industrial Max Min Max Units Notes ew Symbol D (VCC = 2.7V to 3.6V) mA mA mA tAVAV = 25 ns tAVAV = 35 ns tAVAV = 45 ns Dependent on output loading and cycle rate. Values obtained without output loads. 3 mA All Inputs Don’t Care, VCC = max Average current for duration of STORE cycle (tSTORE) 10 mA W ≥ (V CC – 0.2V) All Other Inputs Cycling at CMOS Levels Dependent on output loading and cycle rate. Values obtained without output loads. 3 3 mA All Inputs Don’t Care Average current for duration of STORE cycle (tSTORE) 3 3 mA E ≥ (VCC -0.2V) All Others VIN≤ 0.2V or ≥ (VCC-0.2V) Standby current level after nonvolatile cycle complete Input Leakage Current ±1 ±1 μA VCC = max VIN = VSS to VCC IOLK Off-State Output Leakage Current ±1 ±1 μA VCC = max VIN = VSS to VCC, E or G ICC2 Average VCC Current during STORE 3 ICC3 Average VCC Current at tAVAV = 200 ns 3V, 25°C, Typical ICC4 Average VCAP Current during AutoStore Cycle ISB VCC Standby Current (Standby, Stable CMOS Levels) IILK 70 60 55 rN 65 55 50 fo Average VCC Current de d ICC1 N ot R ec om m en 10 VIH Input Logic “1” Voltage 2.0 VCC+0.3 2.0 VCC+0.3 V All Inputs VIL Input Logic “0” Voltage VSS–0.5 0.8 VSS–0.5 0.8 V All Inputs V IOUT = – 2 mA 0.4 V IOUT = 4 mA ≥ VIH VOH Output Logic “1” Voltage VOL Output Logic “0” Voltage TA Operating Temperature 0 70 –40 85 °C VCC Operating Voltage 2.7 3.6 2.7 3.6 V 3.3V + 0.3V 120 17 120 μF Between VCAP pin and VSS, 5V rated. 2.4 2.4 0.4 VCAP Storage Capacitance 17 NVC Nonvolatile STORE operations 200 200 DATAR Data Retention 20 20 Note K Years At 55 °C The HSB pin has IOUT=-10 uA for VOH of 2.4 V, this parameter is characterized but not tested. Document Number: 001-51592 Rev. *A Page 4 of 17 [+] Feedback STK14CA8 AC Test Conditions Input Pulse Levels ....................................................0V to 3V Input Rise and Fall Times ................................................. ≤ 5 ns Input and Output Timing Reference Levels .................... 1.5V Output Load..................................See Figure 4 and Figure 5 Capacitance (TA = 25°C, f = 1.0 MHz) Input Capacitance 7 pF COUT Output Capacitance 7 pF Conditions ig ns Max Units CIN ΔV = 0 to 3V ΔV = 0 to 3V 3.0V rN 577 Ohms ew Figure 4. AC Output Loading es Parameter[2] D Symbol OUTPUT 30 pF INCLUDING SCOPE AND FIXTURE en de d fo 789 Ohms m Figure 5. AC Output Loading for Tristate Specifications (tHZ, tLZ, tWLQZ, tWHQZ, tGLQX, tGHQZ) 577 Ohms OUTPUT 789 Ohms 5 pF INCLUDING SCOPE AND FIXTURE N ot R ec om 3.0V Note 2. These parameters are guaranteed but not tested. Document Number: 001-51592 Rev. *A Page 5 of 17 [+] Feedback STK14CA8 SRAM READ Cycles #1 and #2 Symbols NO. STK14CA8-25 STK14CA8-35 STK14CA8-45 Parameter #1 #2 Alt. Min Max Min Max tELQV tACS Chip Enable Access Time 2 tELEH[3] tRC Read Cycle Time 3 tAVQV[4] tAVQV[4] tAA Address Access Time 25 35 45 ns tGLQV tOE Output Enable to Data Valid 12 15 20 ns tAXQX[4] tOH Output Hold after Address Change 3 3 3 ns 6 tELQX tLZ Address Change or Chip Enable to Output Active 3 3 3 ns 7 tEHQZ[5] tHZ Address Change or Chip Disable to Output Inactive 8 tGLQX tOLZ Output Enable to Output Active tGHQZ[5] tELICCH[2] tEHICCL[2] tOHZ Output Disable to Output Inactive tPA Chip Enable to Power Active tPS Chip Disable to Power Standby 9 10 11 0 es 13 D 10 0 13 0 15 35 ns ns 15 0 25 ns ns 0 10 0 45 45 ig ns 35 ew 5 tAXQX[4] 25 rN 4 35 Units Max tAVAV[3] 1 25 Min ns ns 45 ns fo Figure 6. SRAM READ Cycle #1: Address Controlled[3, 4, 6] d 2 tAVAV ADDRESS tAXQX DATA VALID m en DQ (DATA OUT) de 3 tAVQV 5 2 29 1 11 6 ot R ec om Figure 7. SRAM READ Cycle #2: E and G Controlled[3, 6] 7 N 3 4 9 8 10 Notes 3. W must be high during SRAM READ cycles. 4. Device is continuously selected with E and G both low 5. Measured ± 200mV from steady state output voltage. 6. HSB must remain high during READ and WRITE cycles Document Number: 001-51592 Rev. *A Page 6 of 17 [+] Feedback STK14CA8 SRAM WRITE Cycles #1 and #2 NO. Symbols #1 #2 STK14CA8-25 STK14CA8-35 STK14CA8-45 Parameter Alt. Min Max Min Max Min Max Units tAVAV tAVAV tWC Write Cycle Time 25 35 45 ns 13 tWLWH tWLEH tWP Write Pulse Width 20 25 30 ns 14 tELWH tELEH tCW Chip Enable to End of Write 20 25 30 ns 15 tDVWH tDVEH tDW Data Setup to End of Write 10 12 15 ns 16 tWHDX tEHDX tDH Data Hold after End of Write 0 0 0 ns 17 tAVWH tAVEH tAW Address Setup to End of Write 20 25 30 ns 18 tAVWL tAVEL tAS Address Setup to Start of Write 0 0 0 ns 19 tWHAX tEHAX tWR Address Hold after End of Write 0 0 ns 20 tWLQZ[5,7] tWZ Write Enable to Output Disable 21 tWHQX tOW Output Active after End of Write es 0 D 10 3 ew 3 ig ns 12 13 15 3 ns ns rN Figure 8. SRAM WRITE Cycle #1: W Controlled[7,8] 12 tAVAV fo ADDRESS 14 tELWH de d E 19 tWHAX 17 tAVWH 18 en tAVWL 13 tWLWH 15 tDVWH m W DATA VALID om DATA IN 16 tWHDX 20 tWLQZ DATA OUT HIGH IMPEDANCE R ec PREVIOUS DATA 21 tWHQX Figure 9. SRAM WRITE Cycle #2: E Controlled[7,8] ot 12 tAVAV N ADDRESS 18 tAVEL 14 tELEH 19 tEHAX E 17 tAVEH W 13 tWLEH 15 tDVEH DATA IN DATA OUT 16 tEHDX DATA VALID HIGH IMPEDANCE Notes 7. If W is low when E goes low, the outputs remain in the high impedance state. 8. E or W must be ≥ VIH during address transitions. Document Number: 001-51592 Rev. *A Page 7 of 17 [+] Feedback STK14CA8 AutoStore/POWER UP RECALL NO. Symbols STK14CA8 Parameter Standard Alternate Min Units Notes 20 ms 9 10, 11 Max 22 tHRECALL Power up RECALL Duration 23 tSTORE STORE Cycle Duration 12.5 ms 24 VSWITCH Low Voltage Trigger Level 2.65 V 25 VCCRISE VCC Rise Time μs 150 ig ns tHLHZ t de d fo rN ew D es Figure 10. AutoStore/POWER UP RECALL 23 23 om m en 25 22 N ot R ec 22 Note Read and Write cycles are ignored during STORE, RECALL, and while VCC is below VSWITCH. Notes 9. tHRECALL starts from the time VCC rises above VSWITCH 10. If an SRAM WRITE has not taken place since the last nonvolatile cycle, no STORE takes place 11. Industrial Grade devices require maximum 15 ms. Document Number: 001-51592 Rev. *A Page 8 of 17 [+] Feedback STK14CA8 Software Controlled STORE/RECALL Cycle NO. Symbols E Cont G Cont STK14CA8-35 STK14CA8-35 STK14CA8-45 Parameter[12,13] Alt Min Max Min Max Min Max Units Notes tAVAV tAVAV tRC STORE/RECALL Initiation Cycle Time 25 35 45 ns 27 tAVEL tAVGL tAS Address Setup Time 0 0 0 ns 28 tELEH tGLGH tCW Clock Pulse Width 20 25 30 ns 29 tEHAX tGHAX Address Hold Time 1 1 1 ns 30 tRECALL tRECALL RECALL Duration ig ns 26 50 50 50 13 μs es Figure 11. Software STORE/RECALL CYCLE: E Controlled[13] 26 27 ew D 26 rN 28 d fo 29 30 om m en de 23 Figure 12. Software STORE/RECALL CYCLE: G Controlled[13] 26 N ot R ec 26 27 28 23 30 29 Notes 12. The software sequence is clocked on the falling edge of E controlled READs or G controlled READs 13. The six consecutive addresses must be read in the order listed in the Software STORE/RECALL Mode Selection Table. W must be high during all six consecutive cycles. Document Number: 001-51592 Rev. *A Page 9 of 17 [+] Feedback STK14CA8 Hardware STORE Cycle NO. Symbols Standard 31 tDELAY 32 tHLHX tHLQZ STK14CA8 Parameter Alternate Min Max Hardware STORE to SRAM Disabled 1 70 Hardware STORE Pulse Width 15 Units Notes μs 14 ns Figure 13. Hardware STORE Cycle es ig ns 32 ew D 23 d fo rN 31 STK14CA8 Min m Standard tSS Soft Sequence Processing Time Units Notes μs 15, 16 Max 70 om 33 Parameter en Symbols NO. de Soft Sequence Commands 33 33 N ot R ec Figure 14. Software Sequence Commands Notes 14. On a hardware STORE initiation, SRAM operation continues to be enabled for time tDELAY to allow read/write cycles to complete. 15. This is the amount of time that it takes to take action on a soft sequence command. Vcc power must remain high to effectively register command. 16. Commands such as Store and Recall lock out I/O until operation is complete which further increases this time. See specific command. Document Number: 001-51592 Rev. *A Page 10 of 17 [+] Feedback STK14CA8 E W G A16-A0 Mode I/O Power H X X X Not Selected Output High Z Standby L H L X Read SRAM Output Data Active L L X X Write SRAM Input Data Active L H L 0x04E38 0x0B1C7 0x083E0 0x07C1F 0x0703F 0x08B45 Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM AutoStore Disable Output Data Output Data Output Data Output Data Output Data Output Data Active 0x04E38 0x0B1C7 0x083E0 0x07C1F 0x0703F 0x04B46 Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM AutoStore Enable Output Data Output Data Output Data Output Data Output Data Output Data D Mode Selection 0x04E38 0x0B1C7 0x083E0 0x07C1F 0x0703F Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM Output Data Output Data Output Data Output Data Output Data Active 0x08FC0 Nonvolatile Store Output High Z ICC2 0x04E38 0x0B1C7 0x083E0 0x07C1F 0x0703F 0x04C63 Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM Nonvolatile Recall Output Data Output Data Output Data Output Data Output Data Output High Z Active ig ns es Active rN ew 17, 18, 19 17, 18, 19 fo d L de H L 17, 18, 19 17, 18, 19 N ot R ec om L H L en L H m L Notes Notes 17. The six consecutive addresses must be in the order listed. W must be high during all six consecutive cycles to enable a nonvolatile cycle. 18. While there are 17 addresses on the STK14CA8, only the lower 16 are used to control software modes 19. I/O state depends on the state of G. The I/O table shown assumes G low Document Number: 001-51592 Rev. *A Page 11 of 17 [+] Feedback STK14CA8 nvSRAM Operation on page 4 for the size of the capacitor. The voltage on the VCAP pin is driven to 5V by a charge pump internal to the chip. A pull up should be placed on W to hold it inactive during power up. nvSRAM To reduce unneeded nonvolatile stores, AutoStore and Hardware Store operations are ignored unless at least one WRITE operation has taken place since the most recent STORE or RECALL cycle. Software initiated STORE cycles are performed regardless of whether a WRITE operation has taken place. The HSB signal can be monitored by the system to detect an AutoStore cycle is in progress. The STK14CA8 nvSRAM has two functional components paired in the same physical cell. These are the SRAM memory cell and a nonvolatile QuantumTrap cell. The SRAM memory cell operates similar to a standard fast static RAM. Data in the SRAM can be transferred to the nonvolatile cell (the STORE operation), or from the nonvolatile cell to SRAM (the RECALL operation). This unique architecture allows all cells to be stored and recalled in parallel. During the STORE and RECALL operations, SRAM READ and WRITE operations are inhibited. The STK14CA8 supports unlimited read and writes similar to a typical SRAM. In addition, it provides unlimited RECALL operations from the nonvolatile cells and up to 200K STORE operations. 0.1µF 10k Ohm fo rN ew W VCC d The STK14CA8 performs a READ cycle whenever E and G are low while W and HSB are high. The address specified on pins A0-16 determine which of the 131,072 data bytes are accessed. When the READ is initiated by an address transition, the outputs are valid after a delay of tAVQV (READ cycle #1). If the READ is initiated by E and G, the outputs are valid at tELQV or at tGLQV, whichever is later (READ cycle #2). The data outputs repeatedly responds to address changes within the tAVQV access time without the need for transitions on any control input pins, and remains valid until another address change or until E or G is brought high, or W and HSB is brought low. D SRAM READ VCC es VCAP VCAP ig ns Figure 15. AutoStore Mode de SRAM WRITE om m en A WRITE cycle is performed whenever E and W are low and HSB is high. The address inputs must be stable prior to entering the WRITE cycle and must remain stable until either E or W goes high at the end of the cycle. The data on the common I/O pins DQ0-7 are written into memory if it is valid tDVWH before the end of a W controlled WRITE or tDVEH before the end of an E controlled WRITE. R ec It is recommended that G be kept high during the entire WRITE cycle to avoid data bus contention on common I/O lines. If G is left low, internal circuitry turns off the output buffers tWLQZ after W goes low. AutoStore Operation N ot The STK14CA8 stores data to nvSRAM using one of three storage operations. These three operations are Hardware Store (activated by HSB), Software Store (activated by an address sequence), and AutoStore (on power down). AutoStore operation is a unique feature of Cypress Quantum Trap technology is enabled by default on the STK14CA8. During normal operation, the device draws current from VCC to charge a capacitor connected to the VCAP pin. This stored charge is used by the chip to perform a single STORE operation. If the voltage on the VCC pin drops below VSWITCH, the part automatically disconnects the VCAP pin from VCC. A STORE operation is initiated with power provided by the VCAP capacitor. Figure 15 shows the proper connection of the storage capacitor (VCAP) for automatic store operation. Refer to DC Characteristics Document Number: 001-51592 Rev. *A Hardware STORE (HSB) Operation The STK14CA8 provides the HSB pin for controlling and acknowledging the STORE operations. The HSB pin is used to request a hardware STORE cycle. When the HSB pin is driven low, the STK14CA8 conditionally initiates a STORE operation after tDELAY. An actual STORE cycle only begins if a WRITE to the SRAM took place since the last STORE or RECALL cycle. The HSB pin has a very resistive pull up and is internally driven low to indicate a busy condition while the STORE (initiated by any means) is in progress. This pin should be externally pulled up if it is used to drive other inputs. SRAM READ and WRITE operations that are in progress when HSB is driven low by any means are given time to complete before the STORE operation is initiated. After HSB goes low, the STK14CA8 continues to allow SRAM operations for tDELAY. During tDELAY, multiple SRAM READ operations may take place. If a WRITE is in progress when HSB is pulled low, it is allowed a time tDELAY to complete. However, any SRAM WRITE cycles requested after HSB goes low are inhibited until HSB returns high. If HSB is not used, it should be left unconnected. Hardware RECALL (Power Up) During power up or after any low power condition (VCC
STK14CA8-NF25ITR 价格&库存

很抱歉,暂时无法提供与“STK14CA8-NF25ITR”相匹配的价格&库存,您可以联系我们找货

免费人工找货