19-5706; Rev 0; 12/10
TION KIT
EVALUA BLE
AVAILA
Up to 8.0Gbps Dual Passive Switches
The MAX4888B/MAX4888C dual double-pole/doublethrow (2 x DPDT), high-speed passive switches are
ideal for switching two half-lanes of PCI ExpressM (PCIe)
data between two possible destinations. These devices
feature a dual digital control input to switch signal paths.
The MAX4888C is intended for use in systems where
both the input and output are capacitively coupled (e.g.,
SAS, SATA, XAUI, and PCIe) and provides a 10FA (typ)
source current and a 60kI (typ) internal biasing resistor
to GND at the AOUT_ and BOUT_ pins.
The devices are fully specified to operate from a single
+3.3V (typ) power supply. Both devices are available
in an industry-standard 3.5mm x 5.5mm, 28-pin TQFN
package. They operate over the -40NC to +85NC extended temperature range.
Applications
Desktop PCs
Features
S Single +3.3V Power-Supply Voltage
S Supports PCIe Gen I, Gen II, and Gen III Data
Rates
S Supports Up To and Including 6.0Gbps SAS/SATA
Signals
S Supports Other High-Speed Interfaces (e.g., XAUI)
S Superior Bandwidth Return Loss
S Small, 3.5mm x 5.5mm, 28-Pin TQFN Package
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX4888BETI+
-40NC to +85NC
28 TQFN-EP*
MAX4888CETI+
-40NC to +85NC
28 TQFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
Notebook PCs
Servers
Typical Operating Circuit
CONNECTION SELECT
VCC
PCIe HOST
AOUTA+
AOUTABOUTA+
BOUTA-
MAX4888C
SAS HOST
AOUTB+
AOUTBBOUTB+
BOUTB-
VCC
SEL
SEL
SELB
SELB
AIN+
AINBIN+
BIN-
AIN+
AINBIN+
BIN-
GND
AOUTA+
AOUTABOUTA+
BOUTA-
PCIe DEVICE
AOUTB+
AOUTBBOUTB+
BOUTB-
SAS DEVICE
MAX4888C
GND
NOTE: CAPACITIVE COUPLING WAS OMITTED TO SIMPLIFY ILLUSTRATION.
PCI Express is a registered trademark of PCI-SIG Corp.
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX4888B/MAX4888C
General Description
MAX4888B/MAX4888C
Up to 8.0Gbps Dual Passive Switches
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND, unless otherwise noted.)
VCC. .........................................................................-0.3V to +4V
SEL, SELB, AIN+, AIN-, BIN+, BIN-, AOUTA+,
AOUTA-, AOUTB+, AOUTB-, BOUTA+,
BOUTA-, BOUTB+, BOUTB- (Note 1)... -0.3V to (VCC + 0.3V)
Continuous Current (AIN_ to AOUTA_/AOUTB_,
BIN_ to BOUTA_/BOUTB_)........................................... Q15mA
Peak Current (AIN_ to AOUTA_/AOUTB_,
BIN_ to BOUTA_/BOUTB_)
(pulsed at 1ms, 10% duty cycle)................................. Q70mA
Continuous Current (SEL, SELB)..................................... Q10mA
Peak Current (SEL, SELB)
(pulsed at 1ms, 10% duty cycle)................................. Q10mA
Continuous Power Dissipation (TA = +70NC)
TQFN (derate 28.6mW/NC above +70NC)..................2286mW
Operating Temperature Range........................... -40NC to +85NC
Junction Temperature......................................................+150NC
Storage Temperature Range............................. -65NC to +150NC
Lead Temperature (soldering, 10s).................................+300NC
Soldering Temperature (reflow).......................................+260NC
Note 1: Signals on SEL, SELB, AIN_, BIN _, AOUTA_, AOUTB_, BOUTA_, and BOUTB_ exceeding VCC or GND are clamped by
internal diodes. Limit forward-diode current to maximum current rating.
PACKAGE THERMAL CHARACTERISTICS (Note 2)
TQFN
Junction-to-Ambient Thermal Resistance (qJA)...........35°C/W
Junction-to-Case Thermal Resistance (qJC)..................2°C/W
Note 2: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a fourlayer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = 3.3V Q10%, TA = -40NC to +85NC, unless otherwise noted. Typical values are at VCC = 3.3V, TA = +25NC, unless otherwise
noted.) (Note 3)
PARAMETER
SYMBOL
CONDITIONS
MIN
VINPUT
AIN_, BIN_, AOUTA_, BOUTA_, AOUTB_,
BOUTB_
-0.3
TYP
MAX
UNITS
VCC 1.8
V
DC PERFORMANCE
Analog-Signal Range
RON
VCC = +3.0V, IAIN_ = IBIN_ = 15mA,
V_OUTA_ = V_OUTB_ = 0V, 1.2V
6.4
8.4
I
DRON
VCC = +3.0V, IAIN_ = IBIN_ = 15mA,
V_OUTA_ = V_OUTB_ = 0V (Note 4)
0.2
1.5
I
VCC = +3.0V, IAIN_ = IBIN_ = 15mA,
V_OUTA_ = V_OUTB_ = 0V, 1.2V (Note 5)
0.3
1
I
-1
+1
FA
VCC = +3.6V , VAIN_ = VBIN_ = 0V, 1.2V;
V_OUTA_ or V_OUTB_ = VAIN_ = VBIN_ or
unconnected (MAX4888B)
-1
+1
FA
Output Short-Circuit Current
All other ports are unconnected
(MAX4888C)
5
15
FA
Output Open-Circuit Voltage
All other ports are unconnected
(MAX4888C)
0.2
0.9
V
On-Resistance
On-Resistance Match
Between Channels
On-Resistance Flatness
_OUTA_ or _OUTB_
Off-Leakage Current
AIN_, BIN_ On-Leakage Current
2
RFLAT(ON)
VCC = +3.6V, VAIN_ = VBIN_ = 0V, 1.2V;
I_OUTA_(OFF),
V_OUTA_ or V_OUTB_ = 1.2V, 0V
I_OUTB_(OFF)
(MAX4888B)
IAIN_(ON),
IBIN_(ON)
0.6
Up to 8.0Gbps Dual Passive Switches
(VCC = 3.3V Q10%, TA = -40NC to +85NC, unless otherwise noted. Typical values are at VCC = 3.3V, TA = +25NC, unless otherwise
noted.) (Note 3)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
AC PERFORMANCE
Switch Turn-On Time
tON_SEL
ZS = ZL = 50I
65
ns
Switch Turn-Off Time
tOFF_SEL
ZS = ZL = 50I, Figure 1, measured at
500MHz
7
ns
Propagation Delay
tPD
ZS = ZL = 50I, Figure 2, measured at
500MHz
43
ps
Output Skew Between Pairs
tSK1
ZS = ZL = 50I, Figure 2, measured at
500MHz
8
ps
Output Skew Between Same
Pair
tSK2
ZS = ZL = 50I, Figure2
10
ps
Differential Return Loss (Note 6)
Differential Insertion Loss
Bandwidth
Differential Crosstalk (Note 6)
Differential Off-Isolation (Note 6)
SDD11
SDD21
0Hz < f P 2.8GHz
-14
2.8GHz < f P 5.0GHz
-8
5.0GHz < f P 8.0GHz
-5
f > 8.0GHz
-1
Table 1
dB
SDD12/SDD21
SDDCTK
SDD21_OFF
dB
8
0Hz < f P 2.5GHz
-30
2.5GHz < f P 5.0GHz
-25
5.0GHz < f P 8.0GHz
-35
f > 8.0GHz
-35
0Hz < f P 2.5GHz
-15
2.5GHz < f P 5.0GHz
-12
5.0GHz < f P 8.0GHz
-12
f > 8.0GHz
-12
GHz
dB
dB
CONTROL INPUT
Input Logic-High
VIH
Input Logic-Low
VIL
Input Logic Hysteresis
1.4
V
0.6
VHYST
130
V
mV
POWER SUPPLY
Power-Supply Range
VCC
VCC Supply Current
ICC
3.0
3.6
V
1
mA
Note 3: All units are 100% production tested at TA = +85NC. Limits over the operating temperature range are guaranteed by
design and characterization and are not production tested.
Note 4: DRON = RON(MAX) - RON(MIN).
Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog-signal range.
Note 6: Guaranteed by design; not production tested.
3
MAX4888B/MAX4888C
ELECTRICAL CHARACTERISTICS (continued)
MAX4888B/MAX4888C
Up to 8.0Gbps Dual Passive Switches
Test Circuits/Timing Diagrams
SOURCE
LOAD
MAX4888B
MAX4888C
ZS
VOUT
Σ
ZL
SEL
50%
SEL
50%
90%
VOUT
10%
tON_SEL
tOFF_SEL
THE FREQUENCY OF THE SIGNAL SHOULD BE ABOVE THE HIGHPASS FILTER CORNER OF THE COUPLING CAPACITORS.
Figure 1. Switching Time
Table 1. Insertion Loss Mask
4
FREQUENCY RANGE (GHz)
MAXIMUM INSERTION LOSS (dB)
0 to 2.5
1/3 x fGHZ + 17/30
2.5 to 5
2/5 x fGHZ - 2/5
5 to 8
18/5 x fGHZ - 4/15
Greater than 8
2 x fGHZ - 12
Up to 8.0Gbps Dual Passive Switches
SOURCE
LOAD
MAX4888B
MAX4888C
VS+
Σ
VS-
VSC+
VCALp - VCALn
VOUTp
ZS
VOUTn
ZL
Σ
ZS
CALIBRATION
VCALp
ZS
TRACES
VCALn
ZL
Σ
ZL
50%
50%
50%
VOUTp - VOUTn
50%
tPDr
VOUTp
VOUTn
ZL
SEL
Σ
VSC-
ZS
tPD = max (tPDr, tPDf)
tPDf
VCM
VCM
VCM
VCM
tSKEW = max (tSK1, tSK2)
tSK1
tSK2
AFTER ELIMINATING SOURCE AND CABLE SKEWS.
Figure 2. Propagation Delay and Output Skew
5
MAX4888B/MAX4888C
Test Circuits/Timing Diagrams (continued)
Typical Operating Characteristics
(VCC = 3.3V, TA = +25NC, unless otherwise noted.)
6.5
6.0
VCC = 3.3V
5.0
4
4.5
3
TA = +25°C
300
TA = -40°C
0.3
0.6
0.9
1.2
1.5
100
0
0.3
0.6
0.9
1.2
-40
1.5
-15
10
35
60
80
70
tON_SEL
60
50
40
30
tOFF_SEL
20
0.9
0
DIFFERENTIAL RETURN LOSS (dB)
MAX4888B/C toc05
90
TURN-ON/OFF TIME (ns)
MAX4888B/C toc04
1.0
100
3.3
3.4
3.5
3.6
-20
-30
-40
-50
-60
MAX4888B
-80
0
3.2
MASK
-10
-70
10
0.8
3.0
3.1
3.2
3.3
3.4
3.5
0
3.6
2
4
MAX4888C
6
8
VCC (V)
VCC (V)
FREQUENCY (GHz)
DIFFERENTIAL INSERTION LOSS
vs. FREQUENCY
DIFFERENTIAL OFF-ISOLATION
vs. FREQUENCY
DIFFERENTIAL CROSSTALK
vs. FREQUENCY
MASK
-8
-10
-12
-14
-16
MAX4888B
2
4
MAX4888C
6
FREQUENCY (GHz)
8
10
-10
-20
-30
-40
-50
-60
0
-10
DIFFERENTIAL CROSSTALK (dB)
-6
MAX4888B/C toc08
-4
0
DIFFERENTIAL OFF-ISOLATION (dB)
MAX4888B/C toc07
0
-2
85
MAX4888B/C toc06
DIFFERENTIAL RETURN LOSS
vs. FREQUENCY
1.1
0
VCC = 3.0V
TURN-ON/OFF TIME
vs. SUPPLY VOLTAGE
VIL
-20
VCC = 3.3V
LOGIC THRESHOLD
vs. SUPPLY VOLTAGE
1.2
-18
VCC = 3.6V
TEMPERATURE (°C)
1.3
3.1
VCC = 3.0V
200
V_IN_ (V)
VIH
3.0
VCC = 3.3V
250
V_IN_ (V)
1.5
1.4
1.8
MAX4888C
VCC = 3.6V
150
2
0
LOGIC THRESHOLD (V)
6
5
VCC = 3.6V
4.0
6
7
MAX4888B
-20
-30
-40
-50
-60
-70
-80
-70
-90
-80
-100
0
2
4
6
FREQUENCY (GHz)
8
10
10
MAX4888B/C toc09
5.5
TA = +85°C
8
350
SUPPLY CURRENT (µA)
VCC = 3.0V
RON (Ω)
RON (Ω)
7.0
9
MAX4888B/C toc02
MAX4888B/C toc01
7.5
SUPPLY CURRENT vs. TEMPERATURE
ON-RESISTANCE vs. V_IN_
10
MAX4888B/C toc03
ON-RESISTANCE vs. V_IN_
8.0
DIFFERENTIAL INSERTION LOSS (dB)
MAX4888B/MAX4888C
Up to 8.0Gbps Dual Passive Switches
0
2
4
6
FREQUENCY (GHz)
8
10
Up to 8.0Gbps Dual Passive Switches
SELB
GND
BOUTA-
BOUTA+
VCC
GND
AOUTA-
AOUTA+
SEL
GND
TOP VIEW
24 23 22 21 20 19 18 17 16 15
14 VCC
VCC 25
GND 26
13 GND
MAX4888B
MAX4888C
VCC 27
GND 28
12 VCC
11 GND
*EP
AOUTB+
7
8
9
10
GND
AIN-
6
BOUTB-
GND
5
BOUTB+
4
BIN-
3
BIN+
2
AOUTB-
1
AIN+
+
TQFN
*CONNECT EXPOSED PAD TO GND.
Pin Description
PIN
NAME
FUNCTION
1, 10, 11,
13, 16,
20, 23,
26, 28
GND
Ground
2
AIN+
Analog Switch 1, Common Positive Terminal
3
AIN-
Analog Switch 1, Common Negative Terminal
4
AOUTB+
Analog Switch 1, Normally Open Positive Terminal
5
AOUTB-
Analog Switch 1, Normally Open Negative Terminal
6
BIN+
Analog Switch 2, Common Positive Terminal
7
BIN-
Analog Switch 2, Common Negative Terminal
8
BOUTB+
Analog Switch 2, Normally Open Positive Terminal
Analog Switch 2, Normally Open Negative Terminal
9
BOUTB-
12, 14,
19, 25,
27
VCC
Positive Supply-Voltage Input. Connect VCC to a 3.0V to 3.6V supply voltage. Bypass VCC to GND with
a 0.1FF ceramic capacitor placed as close as possible to the device. See the Board Layout section.
15
SELB
Control Signal Input. SELB has a 70kI (typ) pullup resistor to VCC. If SELB is not in use, leave
unconnected.
17
BOUTA-
Analog Switch 2, Normally Closed Negative Terminal
18
BOUTA+
Analog Switch 2, Normally Closed Positive Terminal
21
AOUTA-
Analog Switch 1, Normally Closed Negative Terminal
22
AOUTA+
Analog Switch 1, Normally Closed Positive Terminal
24
SEL
Control Signal Input. SEL has a 70kI (typ) pulldown resistor to GND.
—
EP
Exposed Pad. Connect EP to GND.
7
MAX4888B/MAX4888C
Pin Configuration
Up to 8.0Gbps Dual Passive Switches
MAX4888B/MAX4888C
Functional Diagram/Truth Table
VCC
VCC
MAX4888B
MAX4888C
AIN+
AOUTA+
AIN+
AOUTA+
AIN-
AOUTA-
AIN-
AOUTA-
AOUTB+
AOUTB+
AOUTB-
AOUTB-
BIN+
BOUTA+
BIN+
BOUTA+
BIN-
BOUTA-
BIN-
BOUTA-
BOUTB+
BOUTB-
VCC
SELB
SEL
CONTROL
GND
8
BOUTB+
AIN_, BIN_ AIN_, BIN_
TO AOUTA_, TO AOUTB_,
BOUTA_
BOUTB_
SEL
SELB
0 (DEFAULT)
0
OFF
1
0
OFF
ON
ON
OFF
OFF
ON
0 (DEFAULT) 1 (DEFAULT)
1
BOUTB-
VCC
1 (DEFAULT)
SELB
SEL
CONTROL
ON
GND
Up to 8.0Gbps Dual Passive Switches
These devices are fully specified to operate from a single
3.0V to 3.6V power supply.
Applications Information
High-Speed Switching
The devices’ primary applications are aimed at sharing
resources. For example, a single lane of PCIe or SAS
can be shared between a single host and two devices.
This could be used for redundancy or to share resources
such as a physical lane or route a lane between one host
and two devices or two hosts and one device.
Board Layout
High-speed switches require proper layout and design
procedures for optimum performance. Keep controlled
impedance PCB traces as short as possible or follow
impedance layouts per the PCIe specification. Ensure
that power-supply bypass capacitors are placed as
close as possible to the device. Multiple bypass capacitors are recommended. Connect all grounds and the
exposed pad to a large ground plane.
Chip Information
Digital Control Input (SEL, SELB)
The devices provide dual digital control inputs (SEL,
SELB) to select the signal path between the AIN_, BIN_
and AOUTA_, BOUTA_ or AOUTB_, BOUTB_ channels. In most cases SEL is chosen and SELB is unconnected. The truth table for the devices is depicted in the
Functional Diagram/Truth Table. SEL has a 70kI (typ)
pulldown resistor to GND and SELB has a 70kI (typ)
pullup resistor to VCC.
Analog-Signal Levels
The devices accept signals from -0.3V to (VCC - 1.8V).
Signals on the AIN+ and BIN+ channels are routed to
either the AOUTA+, BOUTA+ or AOUTB+, BOUTB+
channels. Signals on the AIN- and BIN- channels are routed to either the AOUTA-, BOUTA- or AOUTB-, BOUTBchannels. The devices are bidirectional switches, allowing AIN_, BIN_ and AOUTA_, BOUTA_, AOUTB_, and
BOUTB_ to be used as either inputs or outputs.
PROCESS: CMOS
Package Information
For the latest package outline information and land patterns,
go to www.maxim-ic.com/packages. Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package
drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
28 TQFN-EP
T283555+1
21-0184
90-0123
9
MAX4888B/MAX4888C
Detailed Description
The MAX4888B high-speed passive switch routes highspeed differential signals such as PCIe, SAS, SATA,
and XAUI from one source to two possible destinations or vice versa. The MAX4888B is ideal for routing
PCIe signals to change the system configuration. The
MAX4888C features a 10FA (typ) source current and
a 60kI (typ) internal biasing resistor to GND at the
AOUTA_, BOUTA_, AOUTB_, and BOUTB_ terminals.
The MAX4888C is ideal for circuits that are capacitively
coupled at both the output and input. These devices are
protocol independent and can be used to switch two different protocol signals over the same physical lane. They
feature dual digital control inputs (SEL, SELB) to switch
signal paths. SEL has a 70kI (typ) pulldown resistor to
GND and SELB has a 70kI (typ) pullup resistor to VCC.
MAX4888B/MAX4888C
Up to 8.0Gbps Dual Passive Switches
Revision History
REVISION
NUMBER
REVISION
DATE
0
12/10
DESCRIPTION
Initial release
PAGES
CHANGED
—
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time.
10
© 2010
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
工商网监
湘ICP备2023018690号
