TL4115AF160Q

TL4115 Series Tact Switch Audio / Visual Computer Peripherals Consumer Electronics Instrumentation Medical Equipment Telecommunication Specifications Features & Benefits • • • • Contact Arrangement: SPST Off - (On) Contact Rating: 12VDC, 50mA Contact Resistance: 500mΩ Max. (Initial) Insulation Resistance: 100MΩ Min. at 100VDC Dielectric Strength: 250VAC for 1 Minute Electrical Life: 600,000 Cycles Operating Temperature: -30°C to 85°C Operating Force: 160gf ± 50gf, 220gf ± 70gf Travel: 0.15mm Bounce: 10m sec. max. RoHS 600,000 cycle life expectancy Tape and Reel packaging Low travel Right angle edge surface mount design Part Number Configurator Series Circuit Actuator “L” Dimension Actuation Force Contact Material TL 4115 A - 2.60 F160 - 160 gf F220 - 220 gf Q - Silver Specifications subject to change without notice 4.30.2021 CAP OPTIONS TOGGLE SWITCHES TACTILE SWITCHES SNAP ACTION SWITCHES SLIDE SWITCHES ROTARY SWITCHES ROCKER SWITCHES PUSHBUTTON SWITCHES NAVIGATION SWITCHES KEYLOCK SWITCHES DIP SWITCHES DETECTOR SWITCHES ANTI-VANDAL SWITCHES Applications / Markets www.e-switch.com 800.867.2717 1 TL4115 Series Tact Switch ANTI-VANDAL SWITCHES Body Dimensions .25 .05 [.010 .002 in] 2 1.75 [.069 in] 2.0 .05 [.079 .002 in] 2.1 .05 [.083 .002 in] CIRCUIT: SPST DIP SWITCHES 1 3.40 MIN [.134 in] DETECTOR SWITCHES 5.4 .05 [.213 .002 in] 3.9 .05 [.154 .002 in] 2.6 .05 [.102 .002 in] 2 KEYLOCK SWITCHES Schematic 1 1.0 .05 [.039 .002 in] NAVIGATION SWITCHES R.30 MAX [R.012 in] 2.4 .05 [.094 .002 in] Recommended PCB Layout PUSHBUTTON SWITCHES ROCKER SWITCHES .40 [.016 in] ROTARY SWITCHES 4.50 [.177 in] 2.10 [.083 in] 3.20 [.126 in] 1.10 [.043 in] TACTILE SWITCHES 3.50 [.138 in] 2.20 [.087 in] 2 1.70 [.067 in] MOUNT POSITION WITHIN 0.15mm FROM PWB EDGE .80 [.031 in] .60 MIN [.024 in] CAP OPTIONS 1 2.60 .10 [.102 .004 in] TOGGLE SWITCHES 2.10 [.083 in] .50 [.020 in] SNAP ACTION SWITCHES .60 [.024 in] 2.20 [.087 in] SLIDE SWITCHES 1.80 [.071 in] PWB BASE PLATE www.e-switch.com 800.867.2717 2 Body Dimensions Tape and Reel 8.00 [.315 in] DETECTOR SWITCHES ANTI-VANDAL SWITCHES TL4115 Series Tact Switch .30 [.012 in] 12.00 [.472 in] 5.50 [.217 in] 4.70 [.185 in] 2.40 [.094 in] 2.40 [.094 in] REEL LABEL DRAWING DIRECTION 380.00 [14.961 in] 100.00 [3.937 in] CAP OPTIONS TOGGLE SWITCHES TACTILE SWITCHES SNAP ACTION SWITCHES SLIDE SWITCHES ROTARY SWITCHES ROCKER SWITCHES PUSHBUTTON SWITCHES NAVIGATION SWITCHES KEYLOCK SWITCHES DIP SWITCHES 1.75 [.069 in] 4.00 [.157 in] www.e-switch.com 800.867.2717 3 TL4115 Series Tact Switch ANTI-VANDAL SWITCHES Recommended Solder Process DETECTOR SWITCHES DIP SWITCHES Most contamination problems can be prevented by exercising care during the cleaning and soldering process. Care should be taken not to immerse or spray unsealed switches during flux removal. Contact E-Switch for specific soldering recommendations and specifications not shown. Generalized soldering procedures are outlined below. KEYLOCK SWITCHES “TYPICAL” SMT REFLOW (Pb and Pb-Free) NAVIGATION SWITCHES Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly Average Ramp-Up Rate (Tsmax to Tp) 3 °C/second max. 3 °C/second max. Preheat -Temperature Min (Tsmin) 100 °C 150 °C -Temperature Max (Tsmax) 150 °C 200 °C -Time (tsmin to tsmax) 60-120 seconds 60-180 seconds Time Maintained above: -Temperature (TL) 183 °C 217 °C -Time (tL) 60-150 seconds 60-150 seconds Time within 5 °C of actual 10-30 seconds 20-40 seconds Peak Temperature (tp) Ramp-Down Rate 6 °C/second max. 6 °C/second max. Time 25 °C to Peak Temperature 6 minutes max. 8 minutes max. PUSHBUTTON SWITCHES ROCKER SWITCHES ROTARY SWITCHES Note 1: All temperatures refer to topside of the package, measured on the package surface. SLIDE SWITCHES SNAP ACTION SWITCHES TACTILE SWITCHES TOGGLE SWITCHES CAP OPTIONS www.e-switch.com 800.867.2717 4