ESD3V3XU1BLE6327XTSA1

TVS Diode Transient Voltage Suppressor Diodes ESD3V3XU1BL Bi-directional Ultra Low Capacitance ESD / Transient Protection Diode ESD3V3XU1BL Data Sheet Revision 1.3, 2013-09-11 Final Power Management & Multimarket Edition 2013-09-11 Published by Infineon Technologies AG 81726 Munich, Germany © 2013 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. ESD3V3XU1BL Revision History: Revision 1.2, 2013-02-06 Page or Item Subjects (major changes since previous revision) Revision 1.3, 2013-09-11 5-6 Updated of Table 2-1, Table 2-2, Table 2-3 and Table 2-4 Trademarks of Infineon Technologies AG AURIX™, BlueMoon™, C166™, CanPAK™, CIPOS™, CIPURSE™, COMNEON™, EconoPACK™, CoolMOS™, CoolSET™, CORECONTROL™, CROSSAVE™, DAVE™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, I²RF™, ISOFACE™, IsoPACK™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OmniTune™, OptiMOS™, ORIGA™, PRIMARION™, PrimePACK™, PrimeSTACK™, PRO-SIL™, PROFET™, RASIC™, ReverSave™, SatRIC™, SIEGET™, SINDRION™, SIPMOS™, SMARTi™, SmartLEWIS™, SOLID FLASH™, TEMPFET™, thinQ!™, TRENCHSTOP™, TriCore™, X-GOLD™, X-PMU™, XMM™, XPOSYS™. Other Trademarks Advance Design System™ (ADS) of Agilent Technologies, AMBA™, ARM™, MULTI-ICE™, KEIL™, PRIMECELL™, REALVIEW™, THUMB™, µVision™ of ARM Limited, UK. AUTOSAR™ is licensed by AUTOSAR development partnership. Bluetooth™ of Bluetooth SIG Inc. CAT-iq™ of DECT Forum. COLOSSUS™, FirstGPS™ of Trimble Navigation Ltd. EMV™ of EMVCo, LLC (Visa Holdings Inc.). EPCOS™ of Epcos AG. FLEXGO™ of Microsoft Corporation. FlexRay™ is licensed by FlexRay Consortium. HYPERTERMINAL™ of Hilgraeve Incorporated. IEC™ of Commission Electrotechnique Internationale. IrDA™ of Infrared Data Association Corporation. ISO™ of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLAB™ of MathWorks, Inc. MAXIM™ of Maxim Integrated Products, Inc. MICROTEC™, NUCLEUS™ of Mentor Graphics Corporation. Mifare™ of NXP. MIPI™ of MIPI Alliance, Inc. MIPS™ of MIPS Technologies, Inc., USA. muRata™ of MURATA MANUFACTURING CO., MICROWAVE OFFICE™ (MWO) of Applied Wave Research Inc., OmniVision™ of OmniVision Technologies, Inc. Openwave™ Openwave Systems Inc. RED HAT™ Red Hat, Inc. RFMD™ RF Micro Devices, Inc. SIRIUS™ of Sirius Satellite Radio Inc. SOLARIS™ of Sun Microsystems, Inc. SPANSION™ of Spansion LLC Ltd. Symbian™ of Symbian Software Limited. TAIYO YUDEN™ of Taiyo Yuden Co. TEAKLITE™ of CEVA, Inc. TEKTRONIX™ of Tektronix Inc. TOKO™ of TOKO KABUSHIKI KAISHA TA. UNIX™ of X/Open Company Limited. VERILOG™, PALLADIUM™ of Cadence Design Systems, Inc. VLYNQ™ of Texas Instruments Incorporated. VXWORKS™, WIND RIVER™ of WIND RIVER SYSTEMS, INC. ZETEX™ of Diodes Zetex Limited. Last Trademarks Update 2010-10-26 Final Data Sheet 3 Revision 1.3, 2013-09-11 ESD3V3XU1BL Bi-directional Ultra Low Capacitance ESD / Transient Protection Diode 1 Bi-directional Ultra Low Capacitance ESD / Transient Protection Diode 1.1 Features • • • • • • ESD / transient protection of high speed data lines exceeding – IEC61000-4-2 (ESD): ±20 kV (air / contact) – IEC61000-4-4 (EFT): ±2.5 kV / ±50 A (5/50 ns) – IEC61000-4-5 (surge): ±3 A (8/20 μs) Maximum working voltage: VRWM = ±3.6 V Ultra low capacitance CL = 0.20 pF (typical) at f = 1 GHz Very low clamping voltage: VCL = 14 V at ITLP = 16 A (typical) according to TLP [1] Very low dynamic resistance: RDYN = 0.45 Ω (typical) Pb-free and halogen-free package (RoHS compliant) 1.2 • • Application Examples USB 3.0, Firewire, DVI, HDMI, S-ATA, DisplayPort, Thunderbolt Mobile HDMI Link, MDDI, MIPI, SWP / NFC 1.3 Product Description Pin 1 marking (lasered) Pin 1 Pin 1 Pin 2 Pin 2 a) Pin configuration b) Schematic diagram P G-TS LP-2_Dual_Diode_S erie_P inConf_and_S chematicDiag. vsd Figure 1-1 Pin Configuration and Schematic Diagram Table 1-1 Ordering Information Type Package Configuration ESD3V3XU1BL TSLP-2-17 1 line, bi-directional Final Data Sheet 4 Marking code X2 Revision 1.3, 2013-09-11 ESD3V3XU1BL Characteristics 2 Characteristics Table 2-1 Maximum Rating at TA = 25 °C, unless otherwise specified 1) Parameter Symbol Values Unit Min. Typ. Max. VESD – – 20 kV IPP – – 3 A Peak pulse power tp = 8/20 μs3) PPK – – 36 W Operating temperature range TOP -40 – 125 °C Storage temperature Tstg -65 – 150 °C ESD (air / contact) discharge 2) Peak pulse current (tp = 8/20 μs) 3) 1) Device is electrically symmetrical 2) VESD according to IEC61000-4-2 (R = 330 Ω, C = 150 pF discharge network) 3) IPP according to IEC61000-4-5 Attention: Stresses above the max. values listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the component. 2.1 Electrical Characteristics at TA = 25 °C, unless otherwise specified   

 
  
  
     




 

 

 

 





              



         
                 !"#   Figure 2-1 Definitions of electrical characteristics Final Data Sheet 5 Revision 1.3, 2013-09-11 ESD3V3XU1BL Characteristics Table 2-2 DC Characteristics at TA = 25 °C, unless otherwise specified 1) Parameter Symbol Values Unit Note / Test Condition Min. Typ. Max. Reverse working voltage VRWM -3.6 – 3.6 V Reverse current IR – 1 50 nA Trigger voltage Vt1 5 – – V Holding voltage Vh 4 4.6 – V IR = 10 mA Unit Note / Test Condition pF VR = 0 V, f = 1 MHz VR = 3.3 V 1) Device is electrically symmetrical Table 2-3 AC Characteristics at TA = 25 °C, unless otherwise specified Parameter Symbol Line capacitance CL Series inductance Table 2-4 LS Values Min. Typ. Max. – 0.22 0.35 – 0.20 – – 0.4 – VR = 0 V, f = 1 GHz nH ESD and Surge Characteristics at TA = 25 °C, unless otherwise specified 1) Parameter Symbol 2) Clamping voltage VCL 3) Clamping voltage 4) Clamping voltage Dynamic resistance 2) Dynamic resistance 4) RDYN Values Unit Note / Test Condition V ITLP = 16 A Min. Typ. Max. – 14 – – 20 – ITLP = 30 A – 12 – VESD = 8 kV – 18 – VESD = 15 kV – 8 – IPP = 3 A – 0.45 – – 1 – Ω 1) Device is electrically symmetrical 2) ANSI/ESD STM5.5.1 - Electrostatic Discharge Sensitive Testing using Transmission Line Pulse (TLP) Model. TLP conditions: Z0 = 50 Ω, tp = 100 ns, tr = 0.6 ns and VTLP averaging window: t1 = 30 ns to t2 = 60 ns, extraction of dynamic resistance using least squares fit of TLP characteristic between ITLP1 = 5 A and ITLP2 = 40 A. Please refer to Application Note AN210[1]. 3) VESD according to IEC61000-4-2, VCL at 30 ns (R = 330 Ω, C = 150 pF discharge network) 4) IPP according to IEC61000-4-5 (tp = 8/20 μs) Final Data Sheet 6 Revision 1.3, 2013-09-11 ESD3V3XU1BL Typical Characteristics 3 Typical Characteristics At TA = 25 °C, unless otherwise specified -6 10 -7 10 -8 IR [A] 10 -9 10 -10 10 10-11 -12 10 -4 -3 -2 -1 0 VR [V] 1 2 3 4 Figure 3-1 Reverse current IR = f(VR) 0.6 0.5 CL [pF] 0.4 0.3 0.2 0.1 0 -4 -3 -2 -1 0 VR [V] 1 2 3 4 Figure 3-2 Line capacitance CL = f(VR), f = 1 MHz Final Data Sheet 7 Revision 1.3, 2013-09-11 ESD3V3XU1BL Typical Characteristics 40 ESD3V3XU1BL RDYN 20 30 15 20 10 10 5 0 0 -10 -5 -20 -10 Equivalent VIEC [kV] ITLP [A] RDYN = 0.45 Ω RDYN = 0.45 Ω -30 -15 -40 -20 -40 -30 -20 -10 0 10 20 30 40 VTLP [V] Figure 3-3 Clamping voltage (TLP): ITLP = f(VTLP) according ANSI/ESD STM5.5.1- Electrostatic Discharge Sensitivity Testing using Transmission Line Pulse (TLP) Model. TLP conditions: Z0 = 50 Ω, tp = 100 ns, tr = 0.6 ns, ITLP and VTLP averaging window: t1 = 30 ns to t2 = 60 ns, extraction of dynamic resistance using squares fit to TLP characteristics between ITLP1 = 5 A and ITLP2 = 40 A. Please refer to Application Note AN210[1] Final Data Sheet 8 Revision 1.3, 2013-09-11 ESD3V3XU1BL Typical Characteristics ESD3V3XU1BL RDYN 3 RDYN = 1.0 Ω 2 IPP [A] 1 0 -1 -2 RDYN = 1.0 Ω -3 -15 -10 -5 0 VCL [V] 5 10 15 Figure 3-4 Pulse current (IEC61000-4-5) versus clamping voltage: IPP = f(VCL) Final Data Sheet 9 Revision 1.3, 2013-09-11 ESD3V3XU1BL Typical Characteristics 200 Scope: 6 GHz, 20 GS/s 175 150 VCL [V] 125 VCL-max-peak = 134 V 100 75 VCL-30ns-peak = 12 V 50 25 0 -25 -50 0 100 200 tp [ns] 300 400 Figure 3-5 Clamping voltage at +8 kV discharge according IEC61000-4-2 (R = 330 Ω, C = 150 pF) 50 Scope: 6 GHz, 20 GS/s 25 0 VCL [V] -25 -50 -75 -100 VCL-max-peak = -134 V -125 VCL-30ns-peak = -12 V -150 -175 -200 0 100 200 tp [ns] 300 400 Figure 3-6 Clamping voltage at -8 kV discharge according IEC61000-4-2 (R = 330 Ω, C = 150 pF) Final Data Sheet 10 Revision 1.3, 2013-09-11 ESD3V3XU1BL Typical Characteristics 200 Scope: 6 GHz, 20 GS/s 175 150 VCL [V] 125 VCL-max-peak = 182 V 100 75 VCL-30ns-peak = 18 V 50 25 0 -25 -50 0 100 200 tp [ns] 300 400 Figure 3-7 Clamping voltage at +15 kV discharge according IEC61000-4-2 (R = 330 Ohm, C = 150 pF) 50 Scope: 6 GHz, 20 GS/s 25 0 VCL [V] -25 -50 -75 -100 VCL-max-peak = -179 V -125 VCL-30ns-peak = -18 V -150 -175 -200 0 100 200 tp [ns] 300 400 Figure 3-8 Clamping voltage at -15 kV discharge according IEC61000-4-2 (R = 330 Ω, C = 150 pF) Final Data Sheet 11 Revision 1.3, 2013-09-11 ESD3V3XU1BL Typical Characteristics 0.5 CL [pF] 0.4 0.3 VR = 0 V 0.2 0.1 0 0 1 2 3 4 5 f [GHz] 6 7 8 9 10 8 9 10 Figure 3-9 Line capacitance: CL = f(f), VR = 0 V 0 -0.1 -0.2 VR = 0 V S21 [dB] -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1 0 1 2 3 4 5 f [GHz] 6 7 Figure 3-10 Insertion loss: S21 = f(f), VR = 0 V Final Data Sheet 12 Revision 1.3, 2013-09-11 ESD3V3XU1BL Package Information 4 Package Information 4.1 TSLP-2-17[2] !       
    
 
   
  
  "  #$       0.45 Copper Solder mask 0.375 0.35 0.275 1 0.925 0.3 0.35 0.6 0.275 Figure 4-1 TSLP-2-17 Package outline (dimension in mm) Stencil apertures TSLP-2-7-FP V01 Figure 4-2 TSLP-2-17 Footprint (dimension in mm)
   
    Figure 4-3 TSLP-2-17 Packing (dimension in mm)
  
   Figure 4-4 TSLP-2-17 Marking (example) Final Data Sheet 13 Revision 1.3, 2013-09-11 ESD3V3XU1BL References References [1] Infineon AG - Application Note AN210: Effective ESD Protection Design at System Level Using VF-TLP Characterization Methodology [2] Infineon AG - Recommendations for PCB Assembly of Infineon TSLP and TSSLP Package Final Data Sheet 14 Revision 1.3, 2013-09-11 w w w . i n f i n e o n . c o m Published by Infineon Technologies AG