IRM8601


 

 
   
          

                       

   
     

  




    
 !" #$%& '  $#()! $&"$*!"$#%!"+* ),!(     
&( '!$#()! $&"$*! '! )!!  !(!*#--# $#!&     
&& "&!#* ).! !"$$" !* "$$#*     
/#!+-.$+*"!# !"$!-!0+!#"!*     
/1.& $!$#(&11!"#*+) #     
))+# '$$#* $)%!# &      
 ((!1 # !$ !(""+      
22/$#( 3")$ %& '     
/#!"! #(* $#"!     
*!#* . '



 
    
2!(!."!*$)#$ +! '!#-$!(!) !"# &*'* !)!"!.!1"$*%!!#(!.!&!( $#((!*#!(%'+ &,# !)* +($ !( !"#&'2!((!$#(!$)&-!$! $**!)%&!(#&!$(-$)!4 !!5'$"6$!*(!*#!($*$#-& !2!(!)(+&$ !(+ + *#$&"$#(!" &'%!(!"(!(%'$)""!**



 
      

       


 
!
"
      
#* +)!# **+"$*+(4244
4
4! "     
)!$&$#"!**+"$*"#( #!47$#4! "     
2! !!0+)!# *1 1!&!**!) !"# &     
2*!  %5!*     
+& )!($0+)!#
    Chip Silicon Black Shell Tinplate Silver-white 





 

 
   
          

                       

   
     

  

  1. This drawing measure is a standard value. All dimensions are in millimeter. 2. In case of designation is tolerance
0.3mm. 3. Lead spacing is measured where the lead emerge from the package. 4. Protruded resin under flange 1.0mm Max. 5. Lens color: Black. 6. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 7. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don't reproduce or cause anyone to reproduce them without EVERLIGHT consent. 8. When using this produce, please observe the absolute maximum ratings and the instructions for use outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets.









 

 
   
          

                       

   8
     

  







! 
       Vcc 0~6 V   Topr -20 ~ +75    Tstg -20 ~ +85    Tsol 260   9))-))&(%(' &!** $#:*!"#(*

 
"#






























! 
     !
"    Vcc 4.5 5 5.5 V DC voltage   Icc --- --- 3 mA No signal input #
$ $% Fo --- 38 --- KHz
&'() 
--- 940 --- nm  ----45 ------- m deg *+ ,-.,/0  8 4 --- ,-.0  --- 35 --- deg ,)(
+') T 400 --- 800 s 1(
+') T 400 --- 800 s ,)(   1(   V 4.5 --- --- V V --- 0.2 0.5 V
  
   





 

 
   
          

                       

   9
     

  

 $
%

&  *1:The ray receiving surface at a vertex and relation to the ray axis in the range of θ= 0° and θ=45°. *2:A range from 30cm to the arrival distance. Average value of 50 pulses.


#$  The specified electro-optical characteristics is satisfied under the following Conditions at the controllable distance. !Measurement place A place that is nothing of extreme light reflected in the room. "External light Project the light of ordinary white fluorescent lamps which are not high Frequency lamps and must be less then 10 Lux at the module surface. (Ee10Lux) #Standard transmitter A transmitter whose output is so adjusted as to'())' *
and the output Wave form shown in Fig.-1.According to the measurement method shown in Fig.-2 the standard transmitter is specified. However , the infrared photodiode to be used for the transmitter should be λp=940nm,∆λ=50nm. Also, photodiode is used of PD438B(Vr=5V). (Standard light / Light source temperature 2856°K). $Measuring system According to the measuring system shown in Fig.-3

+
 





 

 
   
          

                       

   :
     

  

 
" RC Filter should be connected closely between Vcc pin and GND pin. Fig.-1 Transmitter Wave Form D.U.T output Pulse
         

     !"  Fig.-2 Measuring Method Fig.-3 Measuring System    
    
          


   
      





 

 
   
          

                       

   
     

  

,-".
."-"./-"./"0"--"
"1' 79!&$ .!3!" $&3!#* . '.*;$.!&!#  7:!&$ .!2$#*)**#
* $#"!.*
!" #
 7 + + +&*!/!# .*.$&
* $#"!  7