MKP9V160RLG

Thyristors Surface Mount – 160V > MKP9V169 MKP9V169 Pb Description Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking state to a low voltage on−state. Conduction will continue like a Triac until the main terminal current drops below the holding current. The plastic axial lead package provides high pulse current capability at low cost. Glass passivation insures reliable operation. Features • High Pressure Sodium Vapor Lighting • Strobes and Flashers • Ignitors • High Voltage Regulators • Pulse Generators Axial Lead • Used to Trigger Gates of SCR’s and Triac AXIAL LEAD CASE 59 STYLE 2 • Indicates UL Registered • These are Pb−Free Devices Functional Diagram Additional Information Datasheet Resources Samples © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount – 160V > MKP9V169 Maximum Ratings (TJ = 25°C unless otherwise noted) Rating Symbol Value Unit VDRM, ±90 V ±0.9 A ITSM ±4.0 A Operating Junction Temperature Range TJ -40 to +125 °C Storage Temperature Range Tstg -40 to +150 °C Peak Repetitive Off−State Voltage (Note 1) (− 40 to 125°C, Sine Wave, 50 to 60 Hz, Gate Open) On-State RMS Current (All Conduction Angles; TL = 80°C, Lead Length = 3/8") VRRM IT Peak Non-Repetitive Surge Current (60 Hz One Cycle, Sine Wave, TJ = 125°C) (RMS) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Thermal Characteristics Rating Thermal Resistance, Junction−to−Lead (Lead Length = 3/8") Lead Solder Temperature (Lead Length ≥ 1/16" from Case, 10 s Max) Symbol Value R8JL 40 TL 260 Unit °C/W °C © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount – 160V > MKP9V169 Electrical Characteristics - OFF (TJ = 25°C unless otherwise noted; Electricals apply in both directions) Characteristic Repetitive Peak Off−State Current TJ = 25ºC Symbol Min Typ Max Unit IDRM - - 5.0 µA (50 to 60 Hz Sine Wave) VDRM = 90V Electrical Characteristics - ON (TJ = 25°C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit VBO 150 _ 170 V VTM – 1.3 1.5 V Dynamic Holding Current (Sine Wave, 50 to 60 Hz, RL = 100 Ω) IH _ _ 100 mA Switching Resistance (Sine Wave, 50 to 60 Hz) RS 0.1 _ _ kΩ Breakover Voltage IBO =200 µA Peak On−State Voltage (ITM = 1 A Peak, Pulse Width ≤ 300 µs, Duty Cycle ≤ 2%) Dynamic Characteristics Characteristic Symbol Min Typ Max Unit Critical Rate−of−Rise of On−State Current, Critical Damped Waveform Circuit (IPK = 130 Ω, Pulse Width = 10 µsec) dv/dt _ 120 − V/µs © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount – 160V > MKP9V169 Voltage Current Characteristic of SCR Symbol VDRM Parameter Peak Repetitive Forward Off State Voltage IDRM Peak Forward Blocking Current VRRM Peak Repetitive Reverse Off State Voltage IRRM Peak Reverse Blocking Current VTM Maximum On State Voltage I S I IS I S) S IH S I (I S ) Holding Current Figure 1. Maximum Le ad Temperature Figure 2. Maximum Ambient Temperature Figure 3. Typical On-State Voltage Figure 4. Typical Power Dissipation © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount – 160V > MKP9V169 Thermal Characterstics Figure 5. Thermal Response Figure 7. Typical Holding Current 1.4 IH , HOLDING CURRENT (NORMALIZED) VBO , BREAKOVER VOLTAGE (NORMALIZED) Figure 6. Typical Breakover Voltage 1.0 0.9 0.8 40 600 81 100 20 140 TJ, JUNCTION TEMPERATURE (°C) 1.2 1.0 0.8 0.6 0.4 06 200 4 0 80 100 120 TJ, JUNCTION TEMPERATURE (°C) Figure 8. Pulse Rating Curve IPK, PEAK CURRENT (AMPS) 100 10 IPK 10% tw 1.0 0.1 1.0 10 100 tw, PULSE WIDTH (ms) © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 140 Thyristors Surface Mount – 160V > MKP9V169 Part Marking System Dimensions B K D F DO 41 AXIAL LEAD CASE 59 STYLE 2 A POLARITY INDICATOR OPTIONAL AS NEEDED (SEE STYLES) F K A MKP 9V160 YYWW Dim A Inches Millimeters Min Max Min Max 0.161 0.205 4.10 5.20 B 0.079 0.106 2.00 2.70 D 0.028 0.034 0.71 0.86 F −−− 0.050 −−− 1.27 K 1.000 −−− 25.40 −−− 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. ALL RULES AND NOTES ASSOCIATED WITH JEDEC DO−41 A= Assembly Location Y= Year WW = Work Week = Pb Free Package (Note: Microdot may be in either location) Ordering Information Device Package Shipping Axial Lead 5000 / Tape & Reel 5000 / Tape & Reel MKP9V160RL MKP9V160RLG 267-04 OBSOLETE, NEW STANDARD 267-05. STYLE 2: NO POLARITY Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17