P0901CA2LRP

SIDACtor ® Protection Thyristors SLIC Protection Pxxx1Cx2L Series - Fixed Voltage TwinSLIC™ in Modified DO-214AA RoHS Pb e3 Description This fixed voltage, unidirectional, modified DO-214 SIDACtor thyristor series is designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. These components provide single port protection implementing voltage switching characteristics for negative polarity surges and a clamping diode for positive polarity surges. Features and Benefits • Low voltage overshoot Agency Approvals Agency Agency File Number E133083 Pinout Designation • Low on-state voltage • Single-port protection • Does not degrade surge capability after multiple surge events within limit • RoHS Compliant and Halogen-Free • Fails short circuit when surged in excess of ratings • Integrated diodes for Pin 3 positive voltage surges • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) Applicable Global Standards Pin 1 Pin 2 Schematic Symbol 1 (T) 3 (R) • TIA-968-A • GR 1089 Intra-building • TIA-968-B • ITU K.20/21 Enhanced Level* • Lightning, 150A (8/20 as defined in IEC 61000-4-5 2nd edition) • ITU K.20/21 Basic Level • YD/T 1082 • GR 1089 Inter-building* • YD/T 993 • YD/T 950 * Series resistance required 2 (G) Additional Information Datasheet © 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/18 Resources Samples SIDACtor ® Protection Thyristors SLIC Protection Electrical Characteristics Part Number Marking VDRM @lDRM=5µA VS @100V/µs V min V max Pin 1-2, 3-2 IH IS IT mA min mA max A max VT @IT=2.2 Amps VF V max V max Capacitance P0641CA2LRP P62A 58 77 120 800 2.2 4 5 P0721CA2LRP P72A 65 88 120 800 2.2 4 5 P0901CA2LRP P92A 75 98 120 800 2.2 4 5 P1101CA2LRP P02A 95 130 120 800 2.2 4 5 P1301CA2LRP P131A 120 160 120 800 2.2 4 5 P1501CA2LRP P151A 140 185 120 800 2.2 4 5 P1701CA2LRP P17A 160 200 120 800 2.2 4 5 P0641CB2LRP P62B 58 77 120 800 2.2 4 5 P0721CB2LRP P72B 65 88 120 800 2.2 4 5 P0901CB2LRP P92B 75 98 120 800 2.2 4 5 P1101CB2LRP P02B 95 130 120 800 2.2 4 5 P1301CB2LRP P131B 120 160 120 800 2.2 4 5 P1501CB2LRP P151B 140 185 120 800 2.2 4 5 P1701CB2LRP P17B 160 200 120 800 2.2 4 5 See Capacitance Values table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are not appropriate for positive ringing systems. Capacitance Values Part Number P0641CA2LRP pF Pin 1-2 / 3-2 Tip-Ground, Ring-Ground MIN MAX 40 70 pF Pin 1-3 Tip-Ring MIN MAX 20 45 P0721CA2LRP 35 70 20 45 P0901CA2LRP 30 65 20 40 P1101CA2LRP 25 55 15 35 P1301CA2LRP 25 45 15 30 P1701CA2LRP 25 40 15 25 P1501CA2LRP 25 45 15 30 P0641CB2LRP 40 70 20 45 P0721CB2LRP 35 70 20 45 P0901CB2LRP 30 65 20 40 P1101CB2LRP 25 55 15 35 P1301CB2LRP 25 45 15 30 P1501CB2LRP 25 45 15 30 P1701CB2LRP 25 40 15 25 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. © 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/18 SIDACtor ® Protection Thyristors SLIC Protection Surge Ratings Series IPP ITSM di/dt 0.2/310 1 0.5/700 2 2/10 1 2/10 2 8/20 1 1.2/50 2 10/160 1 10/160 2 10/560 1 10/560 2 5/320 1 9/720 2 10/360 1 10/360 2 10/1000 1 10/1000 2 5/310 1 10/700 2 50/60 Hz A min A min A min A min A min A min A min A min A min A min A/µs max A 20 150 150 90 50 75 75 45 75 20 500 B 25 250 250 150 100 100 125 80 100 30 500 Notes: 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Symbol Parameter Value Unit Modified DO-214AA TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 85 °C/W Series Package Pin 3 Pin 2 V-I Characteristics tr x td Pulse Waveform +I VS VDRM VF VT -V IDRM +V IH IS IPP – Peak Pulse Current – %IPP Pin 1 Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 IT 0 td tr t – Time (µs) -I Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 °C 4 IH (TC = 25ºC) 2.0 14 12 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature 2 0 -4 -6 1.8 1.6 1.4 1.0 0.8 0.6 0.4 -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C © 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/18 25°C 1.2 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC SIDACtor ® Protection Thyristors SLIC Protection Soldering Parameters Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Figure 1 TP TL TS(max) Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL Recognized compound meeting flammability rating V-0. Critical Zone TL to TP tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications Physical Specifications Lead Material tP Ramp-up Temperature Reflow Condition High Temp Voltage Blocking 80% Rated VDRM (VAC Peak) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C peak). JEDEC-J-STD-020, Level 1 Compak PM Drawing for pg 100 Fixed Volt TwinSLIC.eps Part Marking Part Numbering P xxx1 C x 2 L RP TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE REEL PACK RoHS COMPLIANT TwinSLIC IDENTIFIER (two chip device) XXXXX XXXXX Part number code (refer to Electrical Characteristics table) Date code IPP RATING PACKAGE TYPE © 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/18 SIDACtor ® Protection Thyristors SLIC Protection Dimensions — Modified DO-214AA PIN 3 B D M N Dimensions P A C A B C D E F G H K M N P PIN 1 PIN 2 H E J 0.079 (2.0) 0.079 (2.0) F K G 0.079 (2.0) 0.040 (1.0) 0.110 (2.8) 0.030 (0.76) Dimensions are in inches (and millimeters). Inches Millimeters Min Max Min Max 0.130 0.201 0.077 0.159 0.030 0.075 0.002 0.077 0.006 0.022 0.027 0.052 0.156 0.220 0.087 0.181 0.063 0.096 0.008 0.104 0.016 0.028 0.033 0.058 3.30 5.10 1.95 4.05 0.75 1.90 0.05 1.95 0.15 0.56 0.69 1.32 3.95 5.60 2.20 4.60 1.60 2.45 0.20 2.65 0.41 0.71 0.84 1.47 Pad Outline (MM) Packing Options Package Type C Description Quantity Added Suffix Industry Standard Modified DO-214AA 3-leaded Tape and Reel Pack 2500 RP EIA-481-D Tape and Reel Specification — Modified DO-214AA 0.157 0.157 (4.0) (4.0) Pin 2 0.472 0.472 0.36 (12.0) (12.0) (9.2) 0.360 (9.2) 0.315 (8.0) 0.315 Pin 1 (8.0) 12.99 (330.0) 0.512 (13.0) Arbor Hole Dia. 0.49 (12.4) Dimensions are in inches Cover tape Pin 3 0.059 DIA (1.5) (and millimeters). Dimensions are in inches (and millimeters). Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/18