R1LV0408CSA-5SI

R1LV0408C-I Series Wide Temperature Range Version 4M SRAM (512-kword × 8-bit) REJ03C0098-0200Z Rev. 2.00 May.25.2004 Description The R1LV0408C-I is a 4-Mbit static RAM organized 512-kword × 8-bit. R1LV0408C-I Series has realized higher density, higher performance and low power consumption by employing CMOS process technology (6-transistor memory cell). The R1LV0408C-I Series offers low power standby power dissipation; therefore, it is suitable for battery backup systems. It has packaged in 32-pin SOP, 32-pin TSOP II and 32-pin STSOP. Features • Single 3 V supply: 2.7 V to 3.6 V • Access time: 55/70 ns (max) • Power dissipation:  Active: 6 mW/MHz (typ)  Standby: 1.5 µW (typ) • Completely static memory.  No clock or timing strobe required • Equal access and cycle times • Common data input and output.  Three state output • Directly TTL compatible.  All inputs and outputs • Battery backup operation. • Operating temperature: −40 to +85°C Rev.2.00, May.25.2004, page 1 of 12 R1LV0408C-I Series Ordering Information Type No. R1LV0408CSP-5SI R1LV0408CSP-7LI R1LV0408CSB-5SI R1LV0408CSB-7LI R1LV0408CSA-5SI R1LV0408CSA-7LI Access time 55 ns 70 ns 55 ns 70 ns 55 ns 70 ns 8mm × 13.4mm STSOP (32P3K-B) 400-mil 32-pin plastic TSOP II (32P3Y-H) Package 525-mil 32-pin plastic SOP (32P2M-A) Rev.2.00, May.25.2004, page 2 of 12 R1LV0408C-I Series Pin Arrangement 32-pin SOP 32-pin TSOP A18 A16 A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 (Top view) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 VCC A15 A17 WE# A13 A8 A9 A11 OE# A10 CS# I/O7 I/O6 I/O5 I/O4 I/O3 A11 A9 A8 A13 WE# A18 A15 VCC A17 A16 A14 A12 A7 A6 A5 A4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 (Top view) 32-pin STSOP 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 OE# A10 CS# I/O7 I/O6 I/O5 I/O4 I/O3 VSS I/O2 I/O1 I/O0 A0 A1 A2 A3 Pin Description Pin name A0 to A18 I/O0 to I/O7 CS# (CS) OE# (OE) WE# (WE) VCC VSS Function Address input Data input/output Chip select Output enable Write enable Power supply Ground Rev.2.00, May.25.2004, page 3 of 12 R1LV0408C-I Series Block Diagram LSB V CC V SS • • • • • MSB A11 A9 A8 A15 A18 A10 A13 A17 A16 A14 A12 Row Decoder Memory Matrix 2,048 × 2,048 I/O0 Input Data Control I/O7 • • Column I/O Column Decoder • • LSB A3 A2A1A0 A4 A5 A6 A7 MSB • • CS# WE# OE# Timing Pulse Generator Read/Write Control Rev.2.00, May.25.2004, page 4 of 12 R1LV0408C-I Series Operation Table WE# × H H L L CS# H L L L L OE# × H L H L Mode Not selected Output disable Read Write Write VCC current ISB, ISB1 ICC ICC ICC ICC I/O0 to I/O7 High-Z High-Z Dout Din Din Ref. cycle   Read cycle Write cycle (1) Write cycle (2) Note: H: VIH, L: VIL, ×: VIH or VIL Absolute Maximum Ratings Parameter Power supply voltage relative to VSS Terminal voltage on any pin relative to VSS Power dissipation Operating temperature Storage temperature range Storage temperature range under bias Symbol VCC VT PT Topr Tstg Tbias Value −0.5 to +4.6 −0.5* to VCC + 0.5* 0.7 −40 to +85 −65 to +150 −40 to +85 1 2 Unit V V W °C °C °C Notes: 1. VT min: −3.0 V for pulse half-width ≤ 30 ns. 2. Maximum voltage is +4.6 V. DC Operating Conditions (Ta = −40 to +85°C) Parameter Supply voltage Symbol VCC VSS Input high voltage Input low voltage Note: VIH VIL Min 2.7 0 2.2 −0.3* 1 Typ 3.0 0   Max 3.6 0 VCC + 0.3 0.6 Unit V V V V 1. VIL min: −3.0 V for pulse half-width ≤ 30 ns. Rev.2.00, May.25.2004, page 5 of 12 R1LV0408C-I Series DC Characteristics Parameter Input leakage current Output leakage current Operating current Average operating current Symbol Min |ILI| |ILO| ICC ICC1     Typ   5*1 8*1 Max Unit Test conditions 1 1 10 25 µA µA mA mA Vin = VSS to VCC CS# = VIH or OE# = VIH or WE# = VIL or VI/O = VSS to VCC CS# = VIL, Others = VIH/ VIL, II/O = 0 mA Min. cycle, duty = 100%, CS# = VIL, Others = VIH/VIL II/O = 0 mA Cycle time = 1 µs, duty = 100%, II/O = 0 mA, CS# ≤ 0.2 V, VIH ≥ VCC − 0.2 V, VIL ≤ 0.2 V CS# = VIH Vin ≥ 0 V, CS# ≥ VCC − 0.2 V ICC2  2*1 5 mA Standby current Standby current −5SI to +85°C to +70°C to +40°C to +25°C −7LI to +85°C to +70°C to +40°C to +25°C Output low voltage ISB ISB1 ISB1 ISB1 ISB1 ISB1 ISB1 ISB1 ISB1 VOL VOL2 VOH VOH2            2.4 0.1*1 0.3   0.7* 0.5*   0.7* 0.5*    2 1 2 1 mA µA µA µA µA µA µA µA µA V V V V 10 8 3 3 20 16 10 10 0.4 0.2   IOL = 2.1 mA IOL = 100 µA IOH = −1.0 mA IOH = −0.1 mA Output high voltage VCC − 0.2  Notes: 1. Typical values are at VCC = 3.0 V, Ta = +25°C and specified loading, and not guaranteed. 2. Typical values are at VCC = 3.0 V, Ta = +40°C and specified loading, and not guaranteed. Capacitance (Ta = +25°C, f = 1.0 MHz) Parameter Input capacitance Input/output capacitance Note: Symbol Cin CI/O Min   Typ   Max 8 10 Unit pF pF Test conditions Vin = 0 V VI/O = 0 V Note 1 1 1. This parameter is sampled and not 100% tested. Rev.2.00, May.25.2004, page 6 of 12 R1LV0408C-I Series AC Characteristics (Ta = −40 to +85°C, VCC = 2.7 V to 3.6 V, unless otherwise noted.) Test Conditions • • • • Input pulse levels: VIL = 0.4 V, VIH = 2.4 V Input rise and fall time: 5 ns Input and output timing reference levels: 1.5 V Output load: 1 TTL Gate + CL (50 pF) (R1LV0408C-5SI) 1 TTL Gate + CL (100 pF) (R1LV0408C-7LI) (Including scope and jig) Read Cycle R1LV0408C-I -5SI Parameter Read cycle time Address access time Chip select access time Output enable to output valid Chip select to output in low-Z Output enable to output in low-Z Chip deselect to output in high-Z Output disable to output in high-Z Output hold from address change Symbol tRC tAA tCO tOE tLZ tOLZ tHZ tOHZ tOH Min 55    10 5 0 0 10 Max  55 55 30   20 20  -7LI Min 70    10 5 0 0 10 Max  70 70 35   25 25  Unit ns ns ns ns ns ns ns ns ns 2 2 1, 2 1, 2 Notes Rev.2.00, May.25.2004, page 7 of 12 R1LV0408C-I Series Write Cycle R1LV0408C-I -5SI Parameter Write cycle time Chip selection to end of write Address setup time Address valid to end of write Write pulse width Write recovery time Write to output in high-Z Data to write time overlap Data hold from write time Output active from end of write Output disable to output in high-Z Symbol tWC tCW tAS tAW tWP tWR tWHZ tDW tDH tOW tOHZ Min 55 50 0 50 40 0 0 25 0 5 0 Max       20    20 -7LI Min 70 60 0 60 50 0 0 30 0 5 0 Max       25    25 Unit ns ns ns ns ns ns ns ns ns ns ns 2 1, 2, 7 3, 12 6 1, 2, 7 4 5 Notes Notes: 1. tHZ, tOHZ and tWHZ are defined as the time at which the outputs achieve the open circuit conditions and are not referred to output voltage levels. 2. This parameter is sampled and not 100% tested. 3. A write occurs during the overlap (tWP) of a low CS# and a low WE#. A write begins at the later transition of CS# going low or WE# going low. A write ends at the earlier transition of CS# going high or WE# going high. tWP is measured from the beginning of write to the end of write. 4. tCW is measured from CS# going low to the end of write. 5. tAS is measured from the address valid to the beginning of write. 6. tWR is measured from the earlier of WE# or CS# going high to the end of write cycle. 7. During this period, I/O pins are in the output state so that the input signals of the opposite phase to the outputs must not be applied. 8. If the CS# low transition occurs simultaneously with the WE# low transition or after the WE# transition, the output remain in a high impedance state. 9. Dout is the same phase of the write data of this write cycle. 10. Dout is the read data of next address. 11. If CS# is low during this period, I/O pins are in the output state. Therefore, the input signals of the opposite phase to the outputs must not be applied to them. 12. In the write cycle with OE# low fixed, tWP must satisfy the following equation to avoid a problem of data bus contention. tWP ≥ tDW min + tWHZ max Rev.2.00, May.25.2004, page 8 of 12 R1LV0408C-I Series Timing Waveform Read Timing Waveform (WE# = VIH) tRC Address Valid address tAA tCO CS# tLZ tOE tOLZ OE# tOHZ tHZ Dout High impedance Valid data tOH Rev.2.00, May.25.2004, page 9 of 12 R1LV0408C-I Series Write Timing Waveform (1) (OE# Clock) tWC Address Valid address tAW OE# tCW CS# *8 tWR tAS tWP WE# tOHZ Dout High impedance tDW Din Valid data tDH Rev.2.00, May.25.2004, page 10 of 12 R1LV0408C-I Series Write Timing Waveform (2) (OE# Low Fixed) tWC Address Valid address tCW tWR CS# *8 tAW tWP WE# tAS tWHZ tOW tOH *9 *10 Dout High impedance tDW tDH *11 Din Valid data Rev.2.00, May.25.2004, page 11 of 12 R1LV0408C-I Series Low VCC Data Retention Characteristics (Ta = −40 to +85°C) Parameter VCC for data retention Data retention current −5SI to +85°C to +70°C to +40°C to +25°C −7LI to +85°C to +70°C to +40°C to +25°C Chip deselect to data retention time Operation recovery time Symbol Min Typ VDR ICCDR ICCDR ICCDR ICCDR ICCDR ICCDR ICCDR ICCDR tCDR tR 2.0         0 4 Max Unit Test conditions*3  10 8 2 1    0.7* 0.5*   0.5*  1 V µA µA µA µA µA µA µA µA ns ns CS# ≥ VCC − 0.2 V, Vin ≥ 0 V VCC = 3.0 V, Vin ≥ 0 V CS# ≥ VCC − 0.2 V 3 3 20 16 0.7*2 10 10   See retention waveform tRC*  Notes: 1. Typical values are at VCC = 3.0 V, Ta = +25°C and specified loading, and not guaranteed. 2. Typical values are at VCC = 3.0 V, Ta = +40°C and specified loading, and not guaranteed. 3. CS# controls address buffer, WE# buffer, OE# buffer, and Din buffer. In data retention mode, Vin levels (address, WE#, OE#, I/O) can be in the high impedance state. 4. tRC = read cycle time. Low VCC Data Retention Timing Waveform (CS# Controlled) tCDR VCC 2.7 V Data retention mode tR 2.2 V VDR CS# 0V CS# ≥ VCC – 0.2 V Rev.2.00, May.25.2004, page 12 of 12 Revision History Rev. Date R1LV0408C-I Series Data Sheet Contents of Modification Page Description Initial issue Features Standby: 2.4 µW (typ) to 1.5 µW (typ) Absolute Maximum Ratings Notes 2 : +7.0 V to +4.6 V DC characteristics −5SI and −7LI items’ description are divided. Low VCC Data Retention Characteristics −5SI and −7LI items’ description are divided. Low VCC Data Retention Timing Waveform 4.5 V to 2.7 V 2.4 V to 2.2 V  1 5 6 12 12 1.00 2.00 Jul.24.2003 May.25.2004 Sales Strategic Planning Div. Keep safety first in your circuit designs! Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. RENESAS SALES OFFICES Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: (408) 382-7500 Fax: (408) 382-7501 Renesas Technology Europe Limited. Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom Tel: (1628) 585 100, Fax: (1628) 585 900 Renesas Technology Europe GmbH Dornacher Str. 3, D-85622 Feldkirchen, Germany Tel: (89) 380 70 0, Fax: (89) 929 30 11 Renesas Technology Hong Kong Ltd. 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong Tel: 2265-6688, Fax: 2375-6836 Renesas Technology Taiwan Co., Ltd. FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan Tel: (2) 2715-2888, Fax: (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. 26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: (21) 6472-1001, Fax: (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: 6213-0200, Fax: 6278-8001 http://www.renesas.com © 2004. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .1.0