154CV-300G-R

te.com 154N Constant Voltage SPECIFICATIONS      Features     O-Ring mount -40℃ to +125℃ Operating Temperature Range Up to ±0.1% Pressure Non-Linearity Solid State Reliability Applications       Medical Instruments Process Control Fresh & Waste Water Measurements Refrigeration/Compressors Pressure Transmitters Hydraulic Controls  316L SS Pressure Sensor Temperature Compensated 0-100mV Output Absolute and Gage 19mm diaphragm diameter The 154N constant voltage is a 19 mm small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The 154N constant voltage is designed for O-ring mounting and OEM applications where compatibility with corrosive media is required. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element. A ceramic substrate is attached to the package that contains lasertrimmed resistors for temperature compensation and offset correction. Please refer to the 154N uncompensated and compensated datasheets for more information on different features of the 154N. CLICK HERE › CONNECT WITH A SPECIALIST TE CONNECTIVITY SENSORS /// 154NCV REVA 10/2021 Page 1 154N Digital Output Pressure Sensor PERFORMANCE SPECIFICATIONS Unless otherwise specified, Supply Voltage: 10VDC; Ambient Temperature: 25°C PARAMETERS ≤005PSI ≥015PSI MIN TYP MAX Span 98 100 Zero Pressure Output -2.0 0 Pressure Non Linearity -0.20 Pressure Hysteresis UNITS NOTES 101 mV 1 1.0 mV 1 - 0.10 %Span 2 -0.05 ±0.02 0.05 %Span MIN TYP MAX 102 99 100 2.0 -1.0 0 - 0.20 -0.10 -0.10 ±0.02 0.10 Repeatability - ±0.02 - - ±0.02 - %Span Input Resistance 5.5 9.0 12.5 5.5 9.0 12.5 KΩ Output Resistance Temperature Error – Span 4.0 - 7.0 4.0 - 6.0 KΩ -1.0 - 1.0 -1.0 - 1.0 %Span 3 Temperature Error – Offset -1.0 - 1.0 -1.0 - 1.0 %Span 3 Thermal Hysteresis – Span -0.25 ±0.05 0.25 -0.25 ±0.05 0.25 %Span 3 Thermal Hysteresis – Offset -0.25 ±0.05 0.25 -0.25 ±0.05 0.25 %Span 3 Long Term Stability – Span - ±0.10 - - ±0.10 - %Span/Year Long Term Stability – Offset - ±0.25 - - ±0.10 - %Span/Year Supply Voltage - 10 14 - 10 14 V 4 Output Load Resistance 5M - - 5M - - Ω 5 Insulation Resistance (50Vdc) 50M - - 50M - - Ω 6 Output Noise (10Hz to 1KHz) - 1.0 - - 1.0 - µV p-p Response Time (10% to 90%) - 0.1 - - 0.1 - ms Pressure Overload - - 3X - - 3X Rated 7 Pressure Burst - - 4X - - 4X Rated 7，8 -20 - 85 °C Compensated Temperature Operating Temperature Storage Temperature Media – Pressure Port 1psi: 0 to 50 5psi: 0 to 70 -20 - 70 -40 - 125 ºC 9 -40 - 125 -40 - 125 ºC 9 Liquids and Gases compatible with 316/316L Stainless Steel Notes 1. Measured at vacuum for absolute (A), ambient for gage (G). 2. Best fit straight line. Pressure non linearity min -0.3% and max +0.3% for 1 PSI. 3. Over the compensated temperature range with respect to 25°C. 4. Guarantees output/input ratiometricity. 5. Load resistance to reduce measurement errors due to output loading. 6. Between case and sensing element. 7. Pressure overload 10-PSI and pressure burst 12 PSI for 1-Psi devices. 8. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer. 9. Maximum temperature range for product with standard cable and connector is -20°C to +105°C. 10. Standard gage units are not recommended for vacuum applications. For vacuum applications below 1/2 atmosphere, consult factory. 11. Device Marking: Each part shall be identified with Model Number, Pressure Range, Type, Lot Number, Serial Number, and Date Code. 12. Shipping/Packaging Requirements: The Stainless Steel diaphragm is protected by a plastic cap. Each unit will be packaged individually in a plastic vial with anti-static foam. 13. Direct mechanical Contact with diaphragm is prohibited. Diaphragm surface must remain free of defects (scratches, punctures, dents, fingerprints, etc) for device to operate properly. Caution is advised when handling parts with exposed diaphragms. Use protective cap whenever devices are not in use. TE CONNECTIVITY SENSORS /// 154NCV REVA 10/2021 Page 2 154N Digital Output Pressure Sensor DIMENSIONS Dimensions are in inches mm TE CONNECTIVITY SENSORS /// 154NCV REVA 10/2021 Page 3 154N Digital Output Pressure Sensor RECOMMENDED MOUNTING DIMENSIONS APPLICATION SCHEMATIC TE CONNECTIVITY SENSORS /// 154NCV REVA 10/2021 Page 4 154N Digital Output Pressure Sensor ORDERING INFORMATION Part Number 154CV – 030 G – R T Pressure Range[psi] 001 (Gage Only) 005 015 030 050 100 300 500 Power Mode/Vent Tube Standard w/Tube T Standard w/o Tube [Blank] Electrical Pressure Type G Gage A Absolute P Solder Pads R Ribbon cable C Cable W/Connector CLICK HERE › CONNECT WITH A SPECIALIST NORTH AMERICA Tel +1 800 522 6752 EUROPE Tel +31 73 624 6999 ASIA Tel +86 0400 820 6015 te.com/sensors TE Connectivity, TE, TE Connectivity (logo) and Every Connection Counts are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. © 2021 TE Connectivity Corporation. All Rights Reserved. Version A7 02/2021 TE CONNECTIVITY SENSORS /// 154NCV REVA 10/2021 Page 5