B-155-03

SPECIFICATION CONTROL DRAWING 1 Product Revision 2 Product Name Product Dimensions Cable Dimensions øA øB L øD øE øF øG min min max max min min max 2.50 3.00 24.50 3.00 1.50 1.00 2.50 B-155-03-35-GA-CL --[0.098] [0.118] [0.965] [0.118] [0.059] [0.040] [0.098] 4.30 4.80 29.30 4.80 2.00 1.50 4.30 B-155-05-35-GA-CL --[0.169] [0.189] [1.154] [0.189] [0.079] [0.059] [0.169] 6.00 6.70 32.00 6.70 3.30 2.80 6.00 B-155-06-35-GA-CL --[0.236] [0.264] [1.260] [0.264] [0.130] [0.110] [0.236] 6.40 7.30 32.50 7.30 3.30 2.80 6.40 B-155-07-35-GA-CL --[0.252] [0.287] [1.280] [0.287] [0.130] [0.110] [0.252] 8.70 9.20 35.50 9.20 4.50 4.00 8.70 B-155-09-35-GA-CL --[0.343] [0.362] [1.398] [0.362] [0.177] [0.157] [0.343] 10.00 11.50 35.50 11.50 4.50 4.00 10.00 B-155-11-35-GA-CL --[0.394] [0.453] [1.398] [0.453] [0.177] [0.157] [0.394] 13.00 15.00 45.50 15.10 7.00 6.50 13.00 B-155-13-35-GA-CL --[0.512] [0.591] [1.791] [0.594] [0.276] [0.256] [0.512] 1 Consult TE Connectivity for individual product revision. Contains more than 1 part name. Qty: Item 2 J 7.00±0.50 [0.276±0.020] 9.00±0.50 [0.354±0.020] 10.00± 0.50 [0.394±0.020] 11.00±1.00 [0.433±0.040] 12.00± 1.00 [0.472±0.040] 13.00±1.00 [0.512±0.040] 17.00±1.00 [0.669±0.040] 1 1 1 1 2 2 3 MATERIALS 1. INSULATION SLEEVE: Transparent heat-shrinkable radiation cross-linked modified polyolefin. 2. SOLDER PREFORMS WITH FLUX: Qty: see table (one solder washer shown). SOLDER: TYPE Sn42Bi58 per ANSI / J-STD-006. FLUX: TYPE ROM1 per ANSI / J-STD-004. 3. MELTABLE SEALING RINGS: Thermally stabilized thermoplastic. 4. GROUND LEAD: Raychem cross-linked polyolefin-insulated wire, stranded tin-plated copper. Consult TE Connectivity for sizes and colors other than listed below. 2 Part no. callout shall be replaced with; GA = wire size “AWG”; AWG 22 available. CL = Lead color designation per MIL-STD-681. Available color: green (5); white (9). APPLICATION 1. These controlled soldering devices are designed for termination of a bare or tin-plated copper shield on a cable having an insulation rated for at least +85C, meeting the dimensional criteria listed in the table above. 2. Temperature range: -55C to +125C. 3. When installed properly, these devices will meet the requirements of TE Connectivity/Raychem Specification RT-1404. 4. For installation procedure and application equipment, consult TE Connectivity /Raychem RPIP 824-00. For best results, prepare the cable as shown: TE Connectivity 300 Constitution Drive, Menlo Park, CA. 94025, U.S.A. TITLE: Raychem Unless otherwise specified dimensions are in millimeters. [Inches dimensions are shown in brackets] TOLERANCES: 0.00 N/A 0.0 N/A 0 N/A PREPARED BY: SOLDERSLEEVE TERMINATOR WITH PRE-INSTALLED LEAD DOCUMENT NO.: B-155-XX-35-GA-CL ANGLES: N/A TE Connectivity reserves the right to amend this drawing at any time. Users should evaluate ROUGHNESS IN the suitability of the product for their MICRON application. DCR NUMBER: REPLACES: PROD. REV.: SEE TABLE CAGE CODE : DOC. ISSUE: DATE: 2 SCALE: 16-Apr-11 SIZE: SHEET: mforonda D050222 --06090 --A 1 of 1 Print Date: 9-May-11 © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company. All Rights Reserved. If this document is printed it becomes uncontrolled. Check for the latest revision.