M7100
Pressure Transducer
SPECIFICATIONS
FEATURES
Hermetic Pressure Ports
Integral Electrical Connector
Survives High Vibration
±0.25% Accuracy
Water Resistant 1M Immersion
APPLICATIONS
On and Off Highway Engines and Vehicles
HVAC Refrigeration Controls
Compressors
Hydraulics
Energy and Water Management
SENSOR SOLUTIONS ///M7100
Performance standard on and off highway engine and
vehicle OEMs
Rugged for heavy equipment and outdoor use
Designed specifically for high volume applications
Stainless steel wetted surfaces
Medium to high pressures
UL Certified
Gage
The M7100 pressure transducer from the Microfused line of MEAS
sets a new price performance standard for demanding engine and
vehicle, and industrial applications. This transducer is suitable for
measurement of liquid or gas pressure, even for difficult media
such as contaminated water, steam and corrosive fluids.
The transducer pressure cavity is machined from a solid piece of
17-4 PH stainless steel. The standard version includes a 1/4 NPT
pipe thread allowing a leak-proof, all metal sealed system. This
automotive grade pressure transducer with stainless steel hermetic
pressure ports and integral electrical connector can boast up to
10,000psi (700bar). The M7100 is UL certified and exceeds the
latest industrial requirements including surge protection and is
overvoltage protected in both positive and reverse polarity.
04/2020
Page 1
M7100
Pressure Transducer
STANDARD RANGES
Range (psi)
Range (bar)
0 to 150
0 to 010
0 to 200
0 to 014
0 to 300
0 to 020
0 to 500
0 to 035
0 to 01K
0 to 070
0 to 1K5
0 to 100
0 to 03K
0 to 200
0 to 05K
0 to 350
0 to 7K5
0 to 500
0 to 10K
0 to 700
Gage
PERFORMANCE SPECIFICATIONS
Ambient Temperature: 25°C (unless otherwise specified);
PARAMETERS
MIN
Steel
Load Resistance
TYP
Copper
MAX
Steel
Copper
KΩ
10
Accuracy (combined linearity, hysteresis & repeatability)
-0.25
0.25
%Span
1
2
Total Error Band
-1.0
-2.5
1.0
2.5
%Span
Compensated Temperature
-20
-30
+85
120
°C
Operating Temperature
-40
+125
Storage Temperature
-50
+125
Insulation Resistance (500VDC)
100
Short Circuit Protected
°C
3
°C
MΩ
4
Yes
Output Noise @ 1kHZ
Long Term Stability
NOTES
UNITS
10
-0.25
Frequency Response @ -3dB
mV
0.25
1
%Span/Year
kHz
Notes
1.
Best fit straight line.
2.
TEB includes all accuracy errors, thermal errors, span and zero tolerances over the compensated temperature range.
3.
Temperature range for product with standard cable is -20°C to +105°C.
4.
Between sensor body to any pins of connector.
5.
The maximum pressure that can be applied without changing the transducer’s performance or accuracy.
6.
The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer
7.
Refer to pressure port Listing notes for installation recommendations.
8.
This product can be configured for custom OEM requirements. Contact Factory for different transfer function. See “Pressure Transfer
Function’ diagram.
9.
Maximum temperature range for product with standard cable is -20oC to 105oC.
10. Do not apply torque to connector housing of transducer
11. To ensure proper environmental sealing and electrical connections when using a mating connector, follow the connector manufacturer’s
installation guidelines.
SENSOR SOLUTIONS ///M7100
04/2020
Page 2
M7100
Pressure Transducer
ENVIRONMENTAL SPECIFICATIONS
Ambient Temperature: 25°C (unless otherwise specified)
PARAMETERS
MIN
Steel
Copper
TYP
Steel
Humidity (@40°C)
93
Pressure Overload
5X
Pressure Cycle
Mechanical Vibration
Copper
Steel
Copper
Mechanical Shock
3X
10M
Steel
Steel
Copper
UNITS
NOTES
%RH
2X
Pressure Burst
Media, Pressure Port
MAX
Copper
Rated
5
Rated
6
Cycles
Fluids compatible with 17-4PH Stainless Steel
Fluids compatible with Brass
20g, 10 ~ 2000Hz
MIL-STD-810C, Method 514.2, Curve L
10g peak, 55~2000Hz MIL-STD-202G, Method 204D, Test Condition C
Half-Sine, Peak: 50g, 11ms
MIL-STD-202, Method 213B, Condition A
Half-Sine, Peak: 50g, 11ms MIL-STD-202G, Method 213B, Condition A
Package Protection
IP67 (IEC60529)
.
AGENCY APPROVALS
RoHS: RoHS 2 (Directive 2011/65/EU)
Industrial Control Equipment CSA 22.2 No. 14-10
UL508 Certified
EMC Performance Criteria: Output Change < ±1.5% FSO
ESD
8kV Contact/15kV Air; Discharge Rate >10s
IEC 61000-4-2
EM Field
100V/m, 1kHz 80% Modulation, 80 ~ 1000MHz
IEC 61000-4-3
Electrical Fast Transient
Level 2, 1kV each line, capacitance coupling
IEC 61000-4-4
Surge
Level 2, 42Ω Impedance, Figure 11 (L-L 500V, L-E 1kV)
IEC 61000-4-5
Conducted RF
Level 2, 3V/130dB, 150kHz ~ 80MHz, 2s Dwell, Clamp Injection
IEC 61000-4-6
Pulse Magnetic Field
Level 3, 100A/m, 10 second pulse interval
IEC 61000-4-9
Emission
Class B, 30dB @ 30-230MHz, 37dB @ 230 – 1000MHz
IEC 55022
SENSOR SOLUTIONS ///M7100
04/2020
Page 3
M7100
Pressure Transducer
PRESSURE PORT INFORMATION
Pressure Port Options
Dim A
Tightening Torque (Nm)
2 = G1/4, BS5380, Male
.43 [11.0]
30~35
4 = 7-16-20 UNF, SAE J1926-2, Male, w/ O-Ring
.36 [9.1]
18~20
5 = 1/4-18 NPT Male
.56 [14.2]
2~3 T.F.F.T.
6 = 1/8-27 NPT Male
.38 [9.7]
2~3 T.F.F.T.
E = R1/4-19, Male
.56 [14.2]
2~3 T.F.F.T.
F = G1/4-19, BS5380, Female
.64 [16.3]
30~35
P = 7/16-20UNF Female w/ Integral Valve Depressor;
1/4 Flare Gasket SAE J513C, Copper
.64 [16.3]
15~16
Q = M10 x 1.0, ISO 6149-2, Male
.37 [9.5]
15~16
S = M12 x 1.5, ISO 6149-2, Male
.43 [11.0]
28~30
G = M14 x 1.5, ISO 6149-2, Male
.43 [11.0]
30~35
U = G1/4, DIN 3852-E, Male
.47 [12.0]
30~35
Notes: Installation
*T.F.F.T.: Turns From Finger Tight
Transducers can be installed by either spanner or deep socket. Torque values provided are for reference: actual torque depends upon mating
port material, surface finish, lubrication and sealing mechanism. Transducers calibration and/or zero may shift if part is over-torqued during
installation. Check for a zero shift after installing.
CONNECTOR INFORMATION
Connector
Connector, Pin Plating
Packard Metri-Pack 150 Series
powerandsignal.com
Sumitomo HV040 Series
sumitomokenki.com
AMP Econoseal-J Mark II 070 Series
te.com
SENSOR SOLUTIONS ///M7100
0.003 – 0.005 mm Sn
0.003 mm Sn over
0.0005 – 0.001 mm Cu
0.0004 mm Au over
0.0013 mm Ni
04/2020
Connector, Mating
Housing P/N: 12065287
Terminals P/N: 12103881
Housing P/N: 6189-6907
Terminals P/N: 8100-3067/8
Housing P/N: 174357
Terminals P/N: 171630
Page 4
M7100
Pressure Transducer
DIMENSIONS
Dimensions are in INCHES [mm]
SENSOR SOLUTIONS ///M7100
04/2020
Page 5
M7100
Pressure Transducer
Copper Tube
SENSOR SOLUTIONS ///M7100
04/2020
Page 6
M7100
Pressure Transducer
CHARTS
Pressure Transfer Function
Output Type vs. Supply
Output Type (Code)
3
4
Supply Voltage
4.75 ~ 5.25V*
8 ~ 32V
Supply Current
4.0 ~ 10.0mA
Output Voltage
0.5 ~ 4.5V*
1.0 ~ 5.0V
Reverse Voltage
16V
Overvoltage
16V
32V
Protection
* Output ratiometric to supply voltage
Pressure Range
psi
bar
150P
200P
300P
500P
01KP
010B
014B
020B
035B
070B
1K5P
03KP
05KP
7K5P
10KP
100B
200B
350B
500B
700B
SENSOR SOLUTIONS ///M7100
Connection Type
Pressure Range (Cu Tube)
psi
bar
150P
010B
300P
020B
450P
1
Cable 2 feet
2
Cable 4 feet
030B
3
Cable 10 feet
500P
035B
7
AMP070 Connector
750P
050B
8
HV040 Sumitomo
9
Packard Connector
M
Cable 1 m
N
Cable 2 m
P
Cable 5 m
R
Cable 10 m
04/2020
Page 7
M7100
Pressure Transducer
ORDERING INFORMATION
M71 3 M – 300P G – T B 0000
Code
3
4
1
2
3
7
8
9
M
N
P
R
0
B
Output
Output Voltage
0.5 – 4.5 V
1.0 – 5.0 V
Copper Tube Pressure Port (T) is available only with Copper Port Material,
C12200 Option (B) and all blue or green options
Cable/Connectors
Cable, 2 feet
Cable, 4 feet
Cable, 10 teet
Amp Connector
HV040 Sumitomo
Packard Connector
Cable 1 meter
Cable, 2 meter
Cable, 5 meter
Cable, 10 meter
Pressure Range [psi]
psi
bar
150P
010B
200P
014B
300P
020B
450P
030B
500P
035B
750P
050B
01KP
070B
1K5P
100B
03KP
200B
05KP
350B
7K5P
500B
10KP
700B
Port Material
17-4PH Stainless Steel
Copper, C12200*
Code
2
4
5
6
E
F
P
Options in green are for both Port Materials
Options in blue are for Copper port only.
Options in black are for 17-4PH St. Steel only
Q
S
G
U
T
Pressure Port
Port
G1/4,BS5380, Male
7/16-20 UNF, SAE
J1926-2, Male, w/ O-ring
1/4-18 NPT Male
1/8-27 NPT Male
R1/4-19 Male
G1/4-19, BS5380,
Female
7/16-20 UNF Female w/
Integral Valve Depressor;
1/4 Flare Gasket SAE
J513C, Copper
M10x1.0 ISO 6149-2,
Male
M12x1.5, ISO 6149-2,
Male
M14x1.5, ISO 6149-2,
Male
G1/4, DIN 3852-E, Male
1/4” OD Copper Tube*
NORTH AMERICA
EUROPE
ASIA
Measurement Specialties, Inc.,
a TE Connectivity Company
Phone: 1 800-522-6752
Email: customercare.frmt@te.com
Measurement Specialties (Europe), Ltd.,
a TE Connectivity Company
Phone: +31 73 624 6999
Email: customercare.lcsb@te.com
Measurement Specialties (China), Ltd.,
a TE Connectivity Company
Phone: +86 0400-820-6015
Email: customercare.shzn@te.com
TE.com/sensorsolutions
Measurement Specialties, Inc., a TE Connectivity company.
Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to herein
might be trademarks of their respective owners.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes
no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard
Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse
of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application.
© 2015
TE Connectivity Ltd. family of companies
SENSOR SOLUTIONS ///M7100
All Rights Reserved.
04/2020
Page 8