NETM1000
Table 1: Dimensions
Inside Diameter (D)
in.
mm.
.118 ± .02
3 ± 0.5
.157 ± .02
4 ± 0.5
.197 ± .02
5 ± 0.5
.236 ± .02
6 ± 0.5
.315 ± .02
8 ± 0.5
.394 ± .02
10 ± 0.5
.472 ± .02
12 ± 0.5
.551 ± .02
14 ± 0.5
Size
3
4
5
6
8
10
12
14
Wall Thickness (W)
in.
mm.
.020 ± .004
0.5 ± .1
.020 ± .004
0.5 ± .1
.020 ± .004
0.5 ± .1
.020 ± .004
0.5 ± .1
.020 ± .004
0.5 ± .1
.020 ± .004
0.5 ± .1
.020 ± .004
0.5 ± .1
.020 ± .004
0.5 ± .1
Table 2: Properties
Property
Dimensions
Tensile Strength
Elongation
Longitudinal Change
Low Temperature Flexibility
4 Hours at -55± 3C
Heat Shock
4 hours at 250± 3C
Heat Age, 168 hours at 175± 3C
followed by tests for
Tensile Strength
Elongation
Volume Resistivity
Flammability
Unit
Inches (mm)
PSI (MPa)
Percent
Percent
--
Requirement
Table 1
1500 (10.3) minimum
150 minimum
-10 maximum
No cracking
Test Method
ASTM D 2671
ASTM D 2671
20 inches/minute
ASTM D 2671
Note 1
--
No dripping, flowing or
cracking
ASTM D 2671
PSI (MPa)
Percent
ohm-m
--
ASTM D 2671
20 inches/minute
ASTM D 2671
ASTM D 2671
Procedure C
Voltage Withstand
Volts
1500 (10.3) minimum
150 minimum
103 minimum
No flaming or glowing
longer than 1 minute
from any flame
application. 25% max.
flag burn. No burning of
cotton.
1000 volts for 1 minute,
minimum
ASTM D 2671
Customer Drawing
©2015 Tyco Electronics Corporation. All Rights Reserved
Title:
NETM1000
Tubing
Tyco Electronics reserves the right to amend this drawing at any
time. Users should evaluate the suitability of the product for their
application
Cage Code:
Scale:
Size:
06090
None
A
Document No :
NETM1000
Rev. Date:
Rev.:
Sheet:
23-Oct-2015
B
1 of 2
If this document is printed it becomes uncontrolled. Check for the latest revision.
Properties, continued
Property
Fluid Resistance
1 Hour at 50C in
Battery Acid
followed by test for:
Weight Increase
24 Hour at 23C in
Gasoline
Diesel Fuel
Transmission Oil
Power Steering Fluid
followed by test for:
Weight Increase
1 Hour at 50C in
Motor Oil 15W/40
Brake Fluid, DOT 4
followed by test for:
Weight Increase
1 Hour at 23C in
Antifreeze 50/50
followed by test for:
Weight Increase
Unit
Requirement
Percent
15 maximum
Percent
15 maximum
Percent
15 maximum
Percent
15 maximum
Test Method
Note 2
Note 1: Test three specimens of tubing for low temperature flexibility as follows: Slide the tubing onto a
stranded AWG wire (nearest AWG which will fit inside the tube). Condition the specimens and a
mandrel, selected from Table 2, in a cold chamber for 4 hours at -55 ± 3C (-67 ± 5F). After
completion of the conditioning period and while still in the cold chamber at the specified
temperature, bend the specimen around the mandrel through not less than 360 degrees in 10 ± 2
seconds. Visually examine the tubing for cracks.
Note 2: Six specimens, three 6-inch (150-mm) tubing specimens, which shall be weighed prior to
immersion and shall be immersed in each of the test fluids listed at the temperature specified.
The volume of the fluid shall not be less than 20 times that of the specimens. After conditioning,
all the specimens shall be lightly wiped and air dried for 30 to 60 minutes at 23 ± 3C (73 ± 5°F).
The three specimens shall be reweighed after immersion and the weight change calculated as a
percentage.
Table 3: Mandrel Dimensions for Bend Testing
Size
Mandrel Diameter
mm
7.9 ± 0.05
9.5± 0.08
3 to 6 inclusive
8 to 14 inclusive
Rev. Date:
Rev.:
23-Oct-2015
B
If this document is printed it becomes uncontrolled. Check for the latest revision.
in.
5/16 ± 0.002
3/8 ± 0.003
Document No.
NETM 1000
Sheet:
2 of 2
很抱歉,暂时无法提供与“NETM1000-3-0-SP”相匹配的价格&库存,您可以联系我们找货
免费人工找货