EL4340IU-T7

DATASHEET EL4340, EL4342 FN7421 Rev.4.00 Oct 4, 2017 500MHz Triple Multiplexing Amplifiers The EL4340, EL4342 are fixed unity gain mux amps featuring high slew rates and excellent bandwidth for video switching. These devices feature a high impedance output state (HIZ) that enables the outputs of multiple devices to be wired together. A power-down mode (ENABLE) is included to turn off un-needed circuitry in power sensitive applications. The ENABLE pin, when pulled high, sets the EL4340, EL4342 into standby power mode - consuming just 18mW. An added feature in the EL4340 is a latch enable function (LE) that allows independent logic control using a common logic bus. Features Ordering Information • ±870 V/µs slew rate PART NUMBER ( Notes 1, 2, 3) • Triple 2:1 and 4:1 multiplexers for RGB • Internally set gain-of-1 • High speed three-state outputs (HIZ) • Power-down mode (ENABLE) • Latch enable (EL4340) • ±5V operation • 500MHz bandwidth PART MARKING PACKAGE (RoHS Compliant) PKG. DWG. # • Typical supply currents 10mA/ch (EL4340) and 15.3mA/ch (EL4342) EL4340IUZ EL4340IUZ 24 Ld QSOP MDP0040 • Pb-free (RoHS compliant) EL4342ILZA 4342ILZ 32 Ld 5x6 QFN L32.5x6A EL4340IUZ-EVAL Evaluation Board Applications EL4342ILZA-EVAL Evaluation Board NOTES: 1. Add “-T13” suffix for 2.5k unit or “-T7” suffix for 1k unit tape and reel options. Refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pbfree material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), see product information page for EL4340, EL4342. For more information on MSL, refer to TB363. Related Literature • For a full list of related documents, visit our website - EL4340, EL4342 product pages • HDTV/DTV analog inputs • Video projectors • Computer monitors • Set-top boxes • Security video • Broadcast video equipment TABLE 1. CHANNEL SELECT LOGIC TABLE EL4340 S0 ENABLE HIZ LE OUTPUT 0 0 0 0 INO (A, B, C) 1 0 0 0 IN1 (A, B, C) X 1 X X Power-down X 0 1 X High Z X 0 0 1 Last S0 State Preserved TABLE 2. CHANNEL SELECT LOGIC TABLE EL4342 FN7421 Rev.4.00 Oct 4, 2017 S1 S0 ENABLE HIZ OUTPUT 0 0 0 0 IN0 (A, B, C) 0 1 0 0 IN1 (A, B, C) 1 0 0 0 IN2 (A, B, C) 1 1 0 0 IN3 (A, B, C) X X 1 X Power-down X X 0 1 High Z Page 1 of 14 EL4340, EL4342 Pin Configurations EL4340 (24 LD QSOP) EL4342 (32 LD QFN) 23 LE IN0B 3 22 ENABLE NIC 4 21 HIZ GND B 5 IN0C 6 19 V+ NIC 7 18 OUTB IN1A 8 NIC 9 26 HIZ 2 27 IN0C GND A 28 NIC 24 NIC 29 IN0B 1 30 NIC IN0A 31 IN0A TOP VIEW 32 GND A TOP VIEW IN1A 1 25 ENABLE NIC 2 24 NIC IN1B 3 AV=1 AV=1 20 OUTA 22 OUTA NIC 4 21 V- IN1C 5 AV=1 23 V+ GND B 6 THERMAL PAD 17 OUTC IN2A 7 AV=1 20 OUTB 19 OUTC 16 VAV=1 IN1B 10 NIC 8 AV=1 15 NIC LATCHED ON HIGH LE IN3C 16 NIC 15 IN3B 14 NIC 13 13 NIC IN3A 12 IN1C 12 17 S1 IN2C 10 14 S0 GND C 11 IN2B 9 GND C 11 18 S0 THERMAL PAD INTERNALLY CONNECTED TO V-. PAD MUST BE TIED TO VNIC = NO INTERNAL CONNECTION NIC = NO INTERNAL CONNECTION EN0 S0 EN0 DECODE EN1 DL Q C IN0(A, B, C) DL Q IN1(A, B, C) C S0 S1 AMPLIFIER BIAS LE EN1 IN0(A, B, C) OUT DECODE EN3 HIZ OUT IN1(A, B, C) EN2 IN2(A, B, C) IN3(A, B, C) AMPLIFIER BIAS ENABLE HIZ A LOGIC HIGH ON LE WILL LATCH THE LAST S0 STATE. THIS LOGIC STATE IS PRESERVED WHEN CYCLING HIZ OR ENABLE FUNCTIONS. FIGURE 1. FUNCTIONAL DIAGRAM EL4340 FN7421 Rev.4.00 Oct 4, 2017 ENABLE FIGURE 2. FUNCTIONAL DIAGRAM EL4342 Page 2 of 14 EL4340, EL4342 Pin Descriptions EL4342 (32 Ld QFN) EL4340 (24 Ld QSOP) PIN NAME EQUIVALENT CIRCUIT Circuit 1 DESCRIPTION 1 8 IN1A 2, 4, 8, 13, 15, 24, 28, 30 4, 7, 9, 13, 15, 24 NIC Channel 1 input for output amplifier “A” 3 10 IN1B 5 12 IN1C Circuit 1 Channel 1 input for output amplifier “C” 6 5 GNDB Circuit 4 Ground pin for output amplifier “B” 7 NA IN2A Circuit 1 Channel 2 input for output amplifier “A” 9 NA IN2B Circuit 1 Channel 2 input for output amplifier “B” Not Internally Connected; it is recommended these pins be tied to ground to minimize crosstalk. Circuit 1 Channel 1 input for output amplifier “B” 10 NA IN2C Circuit 1 Channel 2 input for output amplifier “C” 11 11 GNDC Circuit 4 Ground pin for output amplifier “C” 12 NA IN3A Circuit 1 Channel 3 input for output amplifier “A” 14 NA IN3B Circuit 1 Channel 3 input for output amplifier “B” 16 NA IN3C Circuit 1 Channel 3 input for output amplifier “C” 17 NA S1 Circuit 2 Channel selection pin MSB (binary logic code) 18 14 S0 Circuit 2 Channel selection pin. LSB (binary logic code) 19 17 OUTC Circuit 3 Output of amplifier “C” 20 18 OUTB Circuit 3 Output of amplifier “B” 21 16 V- Circuit 4 Negative power supply 22 20 OUTA Circuit 3 Output of amplifier “A” 23 19 V+ Circuit 4 Positive power supply 25 22 ENABLE Circuit 2 Device enable (active low). Internal pull-down resistor ensures the device will be active with no connection to this pin. A logic High on this pin puts device into power-down mode. In power-down mode only logic circuitry is active. All logic states are preserved post power-down. This state is not recommended for logic control where more than one MUX-amp share the same video output line. - 23 LE Circuit 2 Device latch enable on the EL4340. A logic high on LE will latch the last (S0, S1) logic state. HIZ and ENABLE functions are not latched with the LE pin. 26 21 HIZ Circuit 2 Output disable (active high). Internal pull-down resistor ensures the device will be active with no connection to this pin. A logic high, puts the outputs in a high impedance state. Use this state to control logic when more than one MUX-amp share the same video output line. 27 6 IN0C Circuit 1 Channel 0 for output amplifier “C” 29 3 IN0B Circuit 1 Channel 0 for output amplifier “B” 31 1 IN0A Circuit 1 Channel 0 for output amplifier “A” 32 2 GNDA Circuit 4 Ground pin for output amplifier “A” V+ V+ IN LOGIC PIN 21k 1.2V 33k - V- GNDC VCIRCUIT 3 CIRCUIT 2 V+ GNDB OUT GND V- CIRCUIT 1 GNDA V+ + THERMAL HEAT SINK PAD CAPACITIVELY COUPLED ~1MΩ VSUBSTRATE VCIRCUIT 4 FN7421 Rev.4.00 Oct 4, 2017 Page 3 of 14 EL4340, EL4342 Absolute Maximum Ratings Thermal Information (TA = +25°C) Supply Voltage (V+ to V-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V- -0.5V, V+ +0.5V Supply Turn-On Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs Digital & Analog Input Current (Note 6). . . . . . . . . . . . . . . . . . . . . . . . 50mA Output Current (Continuous) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7). . . . . . . . . 2500V Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300V Thermal Resistance (Typical) JA (°C/W) JC (°C/W) 32 Ld QFN Package (Notes 4, 5) . . . . . . . . 35 1.3 to 8 24 Ld QSOP Package (Note 4) . . . . . . . . . . 88 N/A Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Ambient Operating Temperature . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . .-40°C to +125°C Power Dissipation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493 CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. JA is measured in free air with the component mounted on a high-effective thermal conductivity test board with “direct attach” features. Refer to TB379. 5. For JC, the “case temp” location is the center of the exposed metal pad on the package underside. 6. If an input signal is applied before the supplies are powered up, the input current must be limited to these maximum values. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications V+ = +5V, V- = -5V, GND = 0V, TA = +25°C, Input Video = 1VP-P and RL = 500Ω to GND, CL = 5pF unless otherwise specified. PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT 30 34 mA GENERAL Enabled Supply Current (EL4340) +IS Enabled No load, VIN = 0V, Enable Low 21.5 39 46 50 mA -IS Enabled No load, VIN = 0V, Enable Low -32 -30 -21 mA -48 -46 -36.5 mA +IS Disabled No load, VIN = 0V, Enable High 1.75 2.8 4.2 mA No load, VIN = 0V, Enable High 3 3.5 4 mA -IS Disabled No load, VIN = 0V, Enable High 10 100 µA Enabled Supply Current (EL4342) Enabled Supply Current (EL4340) Enabled Supply Current (EL4342) Disabled Supply Current (EL4340) Disabled Supply Current (EL4342) Disabled Supply Current Positive and Negative Output Swing VOUT VIN = ±3.5V, RL = 500Ω ±3.1 ±3.4 V Output Current IOUT RL = 10Ω to GND ±80 ±135 mA 7 Output Offset Voltage (EL4340) VOS -15 Output Offset Voltage (EL4342) VOS -10 Input Bias Current Ib VIN = 0V -0.5 -2 +15 mV +10 mV -3 µA HIZ Output Resistance ROUT HIZ = Logic High 1.4 Enabled Output Resistance ROUT HIZ = Logic Low 0.2 Ω VIN = ±3.5V 10 MΩ Input Resistance Voltage Gain Output Current in Three-State RIN ACL or AV ITRI VIN = ±1.5V, RL= 500Ω VOUT = 0V MΩ 0.98 0.99 1.02 V/V 8 15 22 µA LOGIC Input High Voltage (Logic Inputs) VIH 2 Input Low Voltage (Logic Inputs) VIL Input High Current (Logic Inputs) IIH VH = 5V Input Low Current (Logic Inputs) IIL VL = 0V tS Step = 1V 215 V 0.8 V 270 340 µA 2 3 µA AC GENERAL 10 ns Power Supply Rejection Ratio PSRR (EL4340) DC, PSRR V+ and V- combined 52 72 dB Power Supply Rejection Ratio PSRR (EL4342) DC, PSRR V+ and V- combined 52 56 dB 0.1% Settling Time FN7421 Rev.4.00 Oct 4, 2017 Page 4 of 14 EL4340, EL4342 Electrical Specifications V+ = +5V, V- = -5V, GND = 0V, TA = +25°C, Input Video = 1VP-P and RL = 500Ω to GND, CL = 5pF unless otherwise specified. (Continued) PARAMETER SYMBOL Channel Isolation ISO Differential Gain Error dG Differential Phase Error dP CONDITIONS MIN f = 10MHz, Ch-Ch X-Talk and Off-Isolation, CL = 1.5pF TYP MAX UNIT 75 dB NTC-7, RL = 150, CL = 1.5pF 0.02 % NTC-7, RL = 150, CL = 1.5pF 0.02 ° -3dB Bandwidth BW CL = 1.5pF 500 MHz 0.1dB Bandwidth FBW CL = 1.5pF 60 MHz CL = 4.7pF 120 MHz 25% to 75%, RL = 150Ω, Input Enabled, CL = 1.5pF ±870 V/µs VIN = 0V, CL = 1.5pF 40 mVP-P VIN = 0V CL = 1.5pF 300 mVP-P VIN = 0V CL = 1.5pF 200 mVP-P VIN = 0V CL = 1.5pF 20 mVP-P VIN = 0V CL = 1.5pF 200 mVP-P 0.1dB Bandwidth Slew Rate SR SWITCHING CHARACTERISTICS Channel-to-Channel Switching Glitch VGLITCH Enable Switching Glitch EL4340 HIZ Switching Glitch Channel-to-Channel Switching Glitch VGLITCH Enable Switching Glitch EL4342 HIZ Switching Glitch VIN = 0V CL = 1.5pF 200 mVP-P Channel Switching Time Low to High tSW-L-H 1.2V logic threshold to 10% movement of analog output 18 ns Channel Switching Time High to Low tSW-H-L 1.2V logic threshold to 10% movement of analog output 20 ns 10% to 90% 1.1 ns Rise and Fall Time tr, tf Propagation Delay tpd 10% to 10% 0.9 ns Latch Enable Hold time (EL4340 only) tLH LE = 0 10 ns Typical Performance Curves SOURCE POWER = -20dBm NORMALIZED GAIN (dB) 8 5 4 CL = 16.5pF 6 CL = 11.5pF 4 CL = 7.3pF CL = 6.2pF 2 0 -2 CL = 4.7pF -4 CL = 2.2pF -6 CL INCLUDES 1.5pF BOARD CAPACITANCE -8 -10 1 10 CL = 1.5pF 100 SOURCE POWER = -20dBm 3 NORMALIZED GAIN (dB) 10 VS = ±5V, RL = 500Ω to GND, TA = +25°C, unless otherwise specified. 1k 2 1 0 -1 RL = 100Ω RL = 150Ω -2 -3 RL = 500Ω -4 -5 RL = 1kΩ 1 10 100 FREQUENCY (MHz) FREQUENCY (MHz) FIGURE 3. GAIN vs FREQUENCY vs CL FIGURE 4. GAIN vs FREQUENCY vs RL FN7421 Rev.4.00 Oct 4, 2017 Page 5 of 14 1k EL4340, EL4342 Typical Performance Curves NORMALIZED GAIN (dB) 0.1 100 SOURCE POWER = -20dBm CL = 4.7pF 0.0 OUTPUT RESISTANCE () 0.2 VS = ±5V, RL = 500Ω to GND, TA = +25°C, unless otherwise specified. (Continued) -0.1 -0.2 CL = 1.5pF -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 1 1 0.1 0.1 1k 10 100 FREQUENCY (MHz) 10 0.2 0 -0.2 -0.4 OUTPUT VOLTAGE (V) 0.4 RL = 500Ω CL = 1.5pF 0.6 -0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -0.8 TIME (5ns/DIV) TIME (5ns/DIV) FIGURE 8. EL4342 TRANSIENT RESPONSE FIGURE 7. EL4340 TRANSIENT RESPONSE 0 0 -10 -10 INPUT X TO OUTPUT Y CROSSTALK -20 INPUT X TO OUTPUT Y CROSSTALK -20 -30 -30 -40 (dB) (dB) 1k 0.8 RL = 500Ω CL = 1.5pF 0.6 OFF ISOLATION INPUT X TO OUTPUT X -60 -40 -50 -60 -70 -70 -80 -80 -90 -100 0.1 100 FIGURE 6. ROUT vs FREQUENCY 0.8 -50 10 FREQUENCY (MHz) FIGURE 5. 0.1dB GAIN vs FREQUENCY OUTPUT VOLTAGE (V) 1 OFF ISOLATION INPUT X TO OUTPUT X -90 1 10 100 FREQUENCY (MHz) FIGURE 9. EL4340 CROSSTALK AND OFF-ISOLATION FN7421 Rev.4.00 Oct 4, 2017 1k -100 0.1 1 10 100 FREQUENCY (MHz) FIGURE 10. EL4342 CROSSTALK AND OFF-ISOLATION Page 6 of 14 1k EL4340, EL4342 Typical Performance Curves VS = ±5V, RL = 500Ω to GND, TA = +25°C, unless otherwise specified. (Continued) 20 20 10 PSRR (V+) 0 -10 -10 -20 -20 PSRR (dB) 0 PSRR (V-) -30 -40 -50 -50 -60 -70 -70 1 10 -80 0.3 1k 1k FIGURE 12. EL4342 PSRR CHANNELS A, B, C VIN = 0V VIN = 1V S0, S1 50Ω TERM. 0 0.5V/DIV 0 VOUT A, B, C 0 VOUT A, B, C 20ns/DIV FIGURE 13. CHANNEL TO CHANNEL SWITCHING GLITCH VIN = 0V ENABLE 50Ω TERM. FIGURE 14. CHANNEL TO CHANNEL TRANSIENT RESPONSE VIN = 1V VIN = 0V ENABLE 0 VIN = 1V 50Ω TERM. 1V/DIV 1V/DIV 100 FIGURE 11. EL4340 PSRR CHANNELS A, B, C 20ns/DIV 0 VOUT A, B, C 1V/DIV 100mV/DIV 10 FREQUENCY (MHz) 0 20mV/DIV 1 FREQUENCY (MHz) S0, S1 50Ω TERM. 1V/DIV 100 PSRR (V-) -40 -60 -80 0.3 PSRR (V+) -30 1V/DIV PSRR (dB) 10 0 20ns/DIV FIGURE 15. ENABLE SWITCHING GLITCH VIN = 0V FN7421 Rev.4.00 Oct 4, 2017 0 VOUT A, B, C 20ns/DIV FIGURE 16. ENABLE TRANSIENT RESPONSE VIN = 1V Page 7 of 14 EL4340, EL4342 Typical Performance Curves HIZ VS = ±5V, RL = 500Ω to GND, TA = +25°C, unless otherwise specified. (Continued) HIZ VIN = 0V 0 1V/DIV 0 200mv/DIV VIN = 1V 50Ω TERM. 1V/DIV 1V/DIV 50Ω TERM. 0 VOUT A, B, C VOUT A, B, C 0 10ns/DIV 10ns/DIV FIGURE 17. HIZ SWITCHING GLITCH VIN = 0V FIGURE 18. HIZ TRANSIENT RESPONSE VIN = 1V 60 3.0 50 2.5 POWER DISSIPATION (W) VOLTAGE NOISE (nV/HZ) JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD-QFN EXPOSED DIEPAD SOLDERED TO PCB PER JESD51-5 40 30 20 10 0 100 10k QFN32 JA = 35°C/W 2.0 1.5 1.136W 1.0 QSOP24 JA = 88°C/W 0.5 0 1k 2.857W 100k 0 FREQUENCY (Hz) 25 50 75 85 100 125 150 AMBIENT TEMPERATURE (°C) FIGURE 19. INPUT NOISE vs FREQUENCY (OUTPUT A, B, C) FIGURE 20. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD POWER DISSIPATION (W) 1.2 1.0 870mW 0.8 QSOP24 JA = 115°C/W 758mW 0.6 QFN32 JA = 125°C/W 0.4 0.2 0 0 25 50 75 85 100 125 150 AMBIENT TEMPERATURE (°C) FIGURE 21. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE FN7421 Rev.4.00 Oct 4, 2017 Page 8 of 14 EL4340, EL4342 video cable-driving. The unity-gain current feedback output amplifiers are stable operating into capacitive loads and bandwidth is optimized with a load of 5pF in parallel with a 500Ω. Total output capacitance can be split between the PCB capacitance and an external load capacitor. AC Test Circuits EL4340, EL4342 VIN CL 5PF 50Ω OR 75Ω RL 500Ω Ground Connections For the best isolation and crosstalk rejection, all GND pins and NIC pins must connect to the GND plane. FIGURE 22A. TEST CIRCUIT WITH OPTIMAL OUTPUT LOAD Control Signals RS VIN 50Ω OR 75Ω CL 5PF 475Ω S0, S1, ENABLE, LE, HIZ - These are binary coded, TTL/CMOS compatible control inputs. The S0, S1 pins select the inputs. All three amplifiers are switched simultaneously from their respective inputs. The ENABLE, LE, HIZ pins are used to disable the part to save power, latch in the last logic state and three-state the output amplifiers, respectively. For control signal rise and fall times less than 10ns the use of termination resistors close to the part will minimize transients coupled to the output. TEST EQUIPMENT EL4340, EL4342 50Ω OR 75Ω 50Ω OR 75Ω FIGURE 22B. TEST CIRCUIT FOR MEASURING WITH 50Ω OR 75Ω INPUT TERMINATED EQUIPMENT RS CL 5pF 50Ω OR 75Ω The ESD protection circuits use internal diodes from all pins the V+ and V- supplies. In addition, a dV/dT- triggered clamp is connected between the V+ and V- pins, as shown in the Equivalent Circuits 1 through 4 section of the Pin Description table. The dV/dT triggered clamp imposes a maximum supply turn-on slew rate of 1V/µs. Damaging currents can flow for power supply rates-of-rise in excess of 1V/µs, such as during hot plugging. Under these conditions, additional methods should be employed to ensure the rate of rise is not exceeded. TEST EQUIPMENT EL4340, EL4342 VIN Power-UP Considerations 50Ω OR 75Ω 50Ω OR 75Ω FIGURE 22C. BACKLOADED TEST CIRCUIT FOR VIDEO CABLE APPLICATION. BANDWIDTH AND LINEARITY FOR RL LESS THAN 500Ω WILL BE DEGRADED. Consideration must be given to the order in which power is applied to the V+ and V- pins, as well as analog and logic input pins. Schottky diodes (Motorola MBR0550T or equivalent) connected from V+ to ground and V- to ground (Figure 23) will shunt damaging currents away from the internal V+ and V- ESD diodes in the event that the V+ supply is applied to the device before the V- supply. FIGURE 22. TEST CIRCUITS Figure 22A illustrates the optimum output load for testing AC performance. Figure 22B illustrates the optimun output load when connecting to 50Ω input terminated equipment. If positive voltages are applied to the logic or analog video input pins before V+ is applied, current will flow through the internal ESD diodes to the V+ pin. The presence of large decoupling capacitors and the loading effect of other circuits connected to V+, can result in damaging currents through the ESD diodes and other active circuits within the device. Therefore, adequate current limiting on the digital and analog inputs is needed to prevent damage during the time the voltages on these inputs are more positive than V+. Application Information General The EL4340, EL4342 triple 2:1 and 4:1 MUX amps are ideal as the matrix element of high performance switchers and routers. Key features include buffered high impedance analog inputs and excellent AC performance at output loads down to 150Ω for V+ SUPPLY LOGIC POWER GND SIGNAL DE-COUPLING CAPS SCHOTTKY PROTECTION V+ LOGIC CONTROL S0 GND IN0 EXTERNAL CIRCUITS V+ V- V+ V+ OUT V+ V- IN1 VV- V- V- SUPPLY FIGURE 23. SCHOTTKY PROTECTION CIRCUIT FN7421 Rev.4.00 Oct 4, 2017 Page 9 of 14 EL4340, EL4342 HIZ State An internal pull-down resistor ensures the device will be active with no connection to the HIZ pin. The HIZ state is established within approximately 15ns (Figure 18 on page 8) by placing a logic high (>2V) on the HIZ pin. If the HIZ state is selected, the output is a high impedance 1.4MΩwithapproximately1.5pF in parallel with a 10µA bias current from the output. Use this state when more than one mux shares a common output. frequency performance may be degraded for traces greater than one inch, unless strip line are used. • Match channel-channel analog I/O trace lengths and layout symmetry. This will minimize propagation delay mismatches. • Maximize use of AC de-coupled PCB layers. All signal I/O lines should be routed over continuous ground planes (for example, no split planes or PCB gaps under these lines). Avoid vias in the signal I/O lines. In the HIZ state the output is three-stated, and maintains its high Z even in the presence of high slew rates. The supply current during this state is same as the active state. • Use proper value and location of termination resistors. Termination resistors should be as close to the device as possible. ENABLE and Power-Down States • When testing use good quality connectors and cables, matching cable types and keeping cable lengths to a minimum. The enable pin is active low. An internal pull-down resistor ensures the device will be active with no connection to the ENABLE pin. The Power-down state is established within approximately 80ns (Figure 16 on page 7), if a logic high (>2V) is placed on the ENABLE pin. In the Power-down state, the output has no leakage but has a large variable capacitance (on the order of 15pF), and is capable of being back-driven. Under this condition, large incoming slew rates can cause fault currents of tens of mA. Do not use this state as a high impedance output when several MUX amps share the same output line. LE State The EL4340 is equipped with a Latch Enable pin. A logic high (>2V) on the LE pin latches the last logic state. This logic state is preserved when cycling HIZ or ENABLE functions. Limiting the Output Current No output short-circuit current limit exists on these parts. All applications need to limit the output current to less than 50mA. Adequate thermal heat sinking of the parts is also required. Application Example Figure 24 on page 11 illustrates the use of the EL4342, two ISL84517 SPST switches, and one NC7ST00P5X NAND gate to mux 3 different component video signals and one RGB video signal. The SPDT switches provide the sync signal for the RGB video and disconnects the sync signal for the component signal. PC Board Layout The AC performance of this circuit depends greatly on the care taken in designing the PC board. The following are recommendations to achieve optimum high frequency performance from your PC board. • Minimum of two power supply de-coupling capacitors are recommended (1000pF, 0.01µF) as close to the devices as possible - Avoid vias between the cap and the device because vias add unwanted inductance. Larger caps can be farther away. When vias are required in a layout, they should be routed as far away from the device as possible. • The NIC pins are placed on both sides of the input pins. These pins are not internally connected to the die. It is recommended these pins be tied to ground to minimize crosstalk. The QFN Package Requires Additional PCB Layout Rules for the Thermal Pad The thermal pad is electrically connected to V- supply through the high resistance IC substrate. Its primary function is to provide heat sinking for the IC. However, because of the connection to the V- supply through the substrate, the thermal pad must be tied to the V- supply to prevent unwanted current flow to the thermal pad. Do not tie this pin to GND as this could result in large back biased currents flowing between GND and V-. The EL4342 uses the package with pad dimensions of D2 = 2.48mm and E2 = 3.4mm. Maximum AC performance is achieved if the thermal pad is attached to a dedicated de-coupled layer in a multi-layered PC board. In cases where a dedicated layer is not possible, AC performance may be reduced at upper frequencies. The thermal pad requirements are proportional to power dissipation and ambient temperature. A dedicated layer eliminates the need for individual thermal pad area. When a dedicated layer is not possible a 1” x 1” pad area is sufficient for the EL4342 that is dissipating 0.5W in +50°C ambient. Pad area requirements should be evaluated on a case by case basis. • The use of low inductance components such as chip resistors and chip capacitors is strongly recommended. • Minimize signal trace lengths. Trace inductance and capacitance can easily limit circuit performance. Avoid sharp corners, use rounded corners when possible. Vias in the signal lines add inductance at high frequency and should be avoided. PCB traces greater than 1" begin to exhibit transmission line characteristics with signal rise/fall times of 1ns or less. High FN7421 Rev.4.00 Oct 4, 2017 Page 10 of 14 Y1 Y2 31 1 Y3 7 R 12 Pb1 29 Pb2 3 Pb3 G 9 14 Pr1 27 Pr2 5 Pr3 10 B 16 R1 75 R3 75 R2 75 R5 75 R4 75 R7 75 R9 75 R6 75 V+ IN2A IN3A 23 1nF 1nF 21 VOUTA 22 OUTB 20 IN1B GNDA 32 IN2B GNDB 6 IN3B GNDC 11 NIC 2 NIC NIC 4 8 NIC 13 NIC 15 NIC 24 NIC 28 NIC 30 HIZ 26 ENABLE 25 S0 18 INOC IN1C IN2C IN3C R12 75 QFN R16 500 S1 17 5V 0.1µF ISL84517IH-T H SYNC 1 V+ COM V5V 0.1µF ISL84517IH-T V SYNC 1 COM Page 11 of 14 SOT-23 IN 4 V+ 0.1µF -5V SOT-23 IN 4 5 1nF 1nF NC 5 1nF 0.1µF -5V 1nF 3 2 5V 0.1µF NC7ST00P5X V- 3 5V 5 NC 2 1 INPUT 4 OUT 3 GND -5V OUTC 19 INOB R11 75 R10 75 R8 75 EL4342IL INOA IN1A 0.1µF 0.1µF EL4340, EL4342 FN7421 Rev.4.00 Oct 4, 2017 5V OPTIONAL SCHOTTKY PROTECTION 1nF INPUT 2 SC70 LOGIC INPUTS FIGURE 24. APPLICATION SHOWING THREE YPBPR CHANNELS AND ONE RGB+HV CHANNEL R18 500 R17 500 EL4340, EL4342 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please visit our website to make sure you have the latest revision. DATE REVISION Oct 4, 2017 FN7421.4 CHANGE Applied new header/footer and formatting. Updated Related Literature section Moved Pin descriptions after Pin Configurations. Updated the following specifications in the EC table: +IS Enabled: changed min spec from 26mA to 21.5mA -IS Enabled: changed max spec from -24mA to -21mA +IS Disable Current: changed min spec from 2.3mA to 1.75mA and max spec from 3.3mA to 4.2mA Input Hi Current (IIH): changed max spec from 320µA to 340µA Input Bias Currents: changed min spec from -1µA to -0.5µA Added Revision History and About Intersil sections. About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing, and high-end consumer markets. For the most updated datasheet, application notes, related documentation, and related parts, see the respective product information page found at www.intersil.com. For a listing of definitions and abbreviations of common terms used in our documents, visit www.intersil.com/glossary. You can report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support. © Copyright Intersil Americas LLC 2005-2017. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN7421 Rev.4.00 Oct 4, 2017 Page 12 of 14 EL4340, EL4342 Quad Flat No-Lead Plastic Package (QFN) Micro Lead Frame Plastic Package (MLFP) L32.5x6A (One of 10 Packages in MDP0046) 32 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (COMPLIANT TO JEDEC MO-220) A MILLIMETERS D N (N-1) (N-2) B 1 2 3 SYMBOL MIN NOMINAL MAX NOTES A 0.80 0.90 1.00 - A1 0.00 0.02 0.05 - D PIN #1 I.D. MARK E 5.00 BSC - D2 2.48 REF - E 6.00 BSC - E2 (N/2) 2X 0.075 C 2X 0.075 C 0.45 b 0.17 - 0.50 0.55 - 0.22 0.27 - c 0.20 REF - e 0.50 BSC - N 32 REF 4 ND 7 REF 6 NE 9 REF 5 0.10 M C A B b Rev 1 2/09 NOTES: (N-2) (N-1) N N LEADS TOP VIEW 3.40 REF L L 1. Dimensioning and tolerancing per ASME Y14.5M-1994. PIN #1 I.D. 2. Tiebar view shown is a non-functional feature. 3 1 2 3 3. Bottom-side pin #1 I.D. is a diepad chamfer as shown. 4. N is the total number of terminals on the device. 5. NE is the number of terminals on the “E” side of the package (or Y-direction). (E2) 6. ND is the number of terminals on the “D” side of the package (or X-direction). ND = (N/2)-NE. (N/2) NE 5 7. Inward end of terminal may be square or circular in shape with radius (b/2) as shown. 7 (D2) BOTTOM VIEW 0.10 C e C (c) SEATING PLANE 0.08 C N LEADS & EXPOSED PAD C 2 A (L) SEE DETAIL "X" A1 SIDE VIEW N LEADS DETAIL X For the most recent package outline drawing, see L32.5x6A. FN7421 Rev.4.00 Oct 4, 2017 Page 13 of 14 EL4340, EL4342 Quarter Size Outline Plastic Packages Family (QSOP) MDP0040 QUARTER SIZE OUTLINE PLASTIC PACKAGES FAMILY INCHES A D SYMBOL QSOP16 QSOP24 QSOP28 TOLERANCE NOTES (N/2)+1 N E PIN #1 I.D. MARK E1 1 (N/2) B 0.010 C A B e H C SEATING PLANE 0.007 0.004 C b C A B A 0.068 0.068 0.068 Max. - A1 0.006 0.006 0.006 ±0.002 - A2 0.056 0.056 0.056 ±0.004 - b 0.010 0.010 0.010 ±0.002 - c 0.008 0.008 0.008 ±0.001 - D 0.193 0.341 0.390 ±0.004 1, 3 E 0.236 0.236 0.236 ±0.008 - E1 0.154 0.154 0.154 ±0.004 2, 3 e 0.025 0.025 0.025 Basic - L 0.025 0.025 0.025 ±0.009 - L1 0.041 0.041 0.041 Basic - N 16 24 28 Reference Rev. F 2/07 NOTES: 1. Plastic or metal protrusions of 0.006” maximum per side are not included. L1 A 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. c SEE DETAIL "X" 0.010 A2 GAUGE PLANE L A1 4°±4° DETAIL X For the most recent package outline drawing, see MDP0040. FN7421 Rev.4.00 Oct 4, 2017 Page 14 of 14