DATASHEET
HA5023
FN3393
Rev 9.00
September 30, 2015
Dual 125MHz Video CurrentFeedback Amplifier
The HA5023 is a wide bandwidth high slew rate dual
amplifier optimized for video applications and gains between
1 and 10. It is a current feedback amplifier and thus yields
less bandwidth degradation at high closed loop gains than
voltage feedback amplifiers.
The low differential gain and phase, 0.1dB gain flatness, and
ability to drive two back terminated 75cables, make this
amplifier ideal for demanding video applications.
The current feedback design allows the user to take
advantage of the amplifier’s bandwidth dependency on the
feedback resistor. By reducing RF, the bandwidth can be
increased to compensate for decreases at higher closed
loop gains or heavy output loads.
Features
• Wide Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 125MHz
• Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475V/s
• Input Offset Voltage . . . . . . . . . . . . . . . . . . . . . . . . 800V
• Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03%
• Differential Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03°
• Supply Current (per Amplifier) . . . . . . . . . . . . . . . . 7.5mA
• ESD Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000V
• Guaranteed Specifications at 5V Supplies
• Pb-Free Plus Anneal Available (RoHS Compliant)
The performance of the HA5023 is very similar to the
popular Intersil HA-5020.
Applications
Ordering Information
• Video Distribution Amplifier/RGB Amplifier
• Video Gain Block
PART
PART NUMBER MARKING
TEMP.
RANGE
(°C)
HA5023IPZ
(Note) (No
longer
available,
recommended
replacement:
HA5023IBZ)
HA5023IPZ
-40 to 85
HA5023IBZ
(Note)
5023IBZ
-40 to 85
8 Ld SOIC
(Pb-free)
HA5023IBZ96
(Note)
5023IBZ
-40 to 85
M8.15
8 Ld SOIC
Tape and Reel
(Pb-free)
PACKAGE
8 Ld PDIP*
(Pb-free)
PKG.
DWG. #
E8.3
• Flash A/D Driver
• Current to Voltage Converter
• Medical Imaging
• Radar and Imaging Systems
• Video Switching and Routing
Pinout
*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing
applications.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
FN3393 Rev 9.00
September 30, 2015
HA5023
(PDIP, SOIC)
TOP VIEW
M8.15
OUT1
1
-IN1
2
+IN1
3
V-
4
-+
+-
8
V+
7
OUT2
6
-IN2
5
+IN2
Page 1 of 17
HA5023
Absolute Maximum Ratings
Thermal Information
Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . .36V
DC Input Voltage (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . VSUPPLY
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V
Output Current (Note 4) . . . . . . . . . . . . . . . . . Short Circuit Protected
ESD Rating (Note 3)
Human Body Model (Per MIL-STD-883 Method 3015.7). . . 2000V
Thermal Resistance (Typical, Note 2)
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 85°C
Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . 4.5V to 15V
JA (°C/W)
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
130
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
160
Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . . 175°C
Maximum Junction Temperature (Plastic Package, Note 1) . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(SOIC - Lead Tips Only)
*Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing
applications.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175°C for die, and below 150°C
for plastic packages. See Application Information section for safe operating area information.
2. JA is measured with the component mounted on an evaluation PC board in free air.
3. The non-inverting input of unused amplifiers must be connected to GND.
4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle)
output current should not exceed 15mA for maximum reliability.
Electrical Specifications
VSUPPLY = 5V, RF = 1k AV = +1, RL = 400 CL 10pF, Unless Otherwise Specified
(NOTE 9)
TEST
LEVEL
TEMP.
(°C)
MIN
TYP
MAX
UNITS
A
25
-
0.8
3
mV
A
Full
-
-
5
mV
Delta VIO Between Channels
A
Full
-
1.2
3.5
mV
Average Input Offset Voltage Drift
B
Full
-
5
-
V/°C
A
25
53
-
-
dB
A
Full
50
-
-
dB
A
25
60
-
-
dB
A
Full
55
-
-
dB
A
Full
2.5
-
-
V
A
25
-
3
8
A
A
Full
-
-
20
A
A
25
-
-
0.15
A/V
A
Full
-
-
0.5
A/V
A
25
-
-
0.1
A/V
A
Full
-
-
0.3
A/V
A
25, 85
-
4
12
A
A
-40
-
10
30
A
A
25, 85
-
6
15
A
A
-40
-
10
30
A
PARAMETER
TEST CONDITIONS
INPUT CHARACTERISTICS
Input Offset Voltage (VIO)
VIO Common Mode Rejection Ratio
VIO Power Supply Rejection Ratio
Input Common Mode Range
Note 5
3.5V VS 6.5V
Note 5
Non-Inverting Input (+IN) Current
+IN Common Mode Rejection
Note 5
(+IBCMR = 1 )
+RIN
+IN Power Supply Rejection
Inverting Input (-IN) Current
Delta -IN BIAS Current Between Channels
FN3393 Rev 9.00
September 30, 2015
3.5V VS 6.5V
Page 2 of 17
HA5023
Electrical Specifications
VSUPPLY = 5V, RF = 1k AV = +1, RL = 400 CL 10pF, Unless Otherwise Specified (Continued)
PARAMETER
-IN Common Mode Rejection
-IN Power Supply Rejection
TEST CONDITIONS
Note 5
3.5V VS 6.5V
(NOTE 9)
TEST
LEVEL
TEMP.
(°C)
MIN
TYP
MAX
UNITS
A
25
-
-
0.4
A/V
A
Full
-
-
1.0
A/V
A
25
-
-
0.2
A/V
A
Full
-
-
0.5
A/V
Input Noise Voltage
f = 1kHz
B
25
-
4.5
-
nV/Hz
+Input Noise Current
f = 1kHz
B
25
-
2.5
-
pA/Hz
-Input Noise Current
f = 1kHz
B
25
-
25.0
-
pA/Hz
Note 11
A
25
1.0
-
-
M
A
Full
0.85
-
-
M
A
25
70
-
-
dB
A
Full
65
-
-
dB
A
25
50
-
-
dB
A
Full
45
-
-
dB
A
25
2.5
3.0
-
V
A
Full
2.5
3.0
-
V
TRANSFER CHARACTERISTICS
Transimpedence
Open Loop DC Voltage Gain
Open Loop DC Voltage Gain
RL = 400, VOUT = 2.5V
RL = 100, VOUT = 2.5V
OUTPUT CHARACTERISTICS
Output Voltage Swing
RL = 150
Output Current
RL = 150
B
Full
16.6
20.0
-
mA
Output Current, Short Circuit
VIN = 2.5V, VOUT = 0V
A
Full
40
60
-
mA
Supply Voltage Range
A
25
5
-
15
V
Quiescent Supply Current
A
Full
-
7.5
10
mA/Op Amp
POWER SUPPLY CHARACTERISTICS
AC CHARACTERISTICS (AV = +1)
Slew Rate
Note 6
B
25
275
350
-
V/s
Full Power Bandwidth
Note 7
B
25
22
28
-
MHz
Rise Time
Note 8
B
25
-
6
-
ns
Fall Time
Note 8
B
25
-
6
-
ns
Propagation Delay
Note 8
B
25
-
6
-
ns
B
25
-
4.5
-
%
Overshoot
-3dB Bandwidth
VOUT = 100mV
B
25
-
125
-
MHz
Settling Time to 1%
2V Output Step
B
25
-
50
-
ns
Settling Time to 0.25%
2V Output Step
B
25
-
75
-
ns
FN3393 Rev 9.00
September 30, 2015
Page 3 of 17
HA5023
Electrical Specifications
VSUPPLY = 5V, RF = 1k AV = +1, RL = 400 CL 10pF, Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
(NOTE 9)
TEST
LEVEL
TEMP.
(°C)
MIN
TYP
MAX
UNITS
AC CHARACTERISTICS (AV = +2, RF = 681
Slew Rate
Note 6
B
25
-
475
-
V/s
Full Power Bandwidth
Note 7
B
25
-
26
-
MHz
Rise Time
Note 8
B
25
-
6
-
ns
Fall Time
Note 8
B
25
-
6
-
ns
Propagation Delay
Note 8
B
25
-
6
-
ns
B
25
-
12
-
%
Overshoot
-3dB Bandwidth
VOUT = 100mV
B
25
-
95
-
MHz
Settling Time to 1%
2V Output Step
B
25
-
50
-
ns
Settling Time to 0.25%
2V Output Step
B
25
-
100
-
ns
Gain Flatness
5MHz
B
25
-
0.02
-
dB
20MHz
B
25
-
0.07
-
dB
AC CHARACTERISTICS (AV = +10, RF = 383)
Slew Rate
Note 6
B
25
350
475
-
V/s
Full Power Bandwidth
Note 7
B
25
28
38
-
MHz
Rise Time
Note 8
B
25
-
8
-
ns
Fall Time
Note 8
B
25
-
9
-
ns
Propagation Delay
Note 8
B
25
-
9
-
ns
B
25
-
1.8
-
%
Overshoot
-3dB Bandwidth
VOUT = 100mV
B
25
-
65
-
MHz
Settling Time to 1%
2V Output Step
B
25
-
75
-
ns
Settling Time to 0.1%
2V Output Step
B
25
-
130
-
ns
Differential Gain (Note 10)
RL = 150
B
25
-
0.03
-
%
Differential Phase (Note 10)
RL = 150
B
25
-
0.03
-
°
VIDEO CHARACTERISTICS
NOTES:
5. VCM = 2.5V. At -40°C Product is tested at VCM = 2.25V because Short Test Duration does not allow self heating.
6. VOUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points.
Slew Rate
7. FPBW = ----------------------------- ; V
= 2V .
2V PEAK PEAK
8. RL = 100, VOUT = 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay.
9. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only.
10. Measured with a VM700A video tester using an NTC-7 composite VITS.
11. VOUT = 2.5V. At -40°C Product is tested at VOUT = 2.25V because Short Test Duration does not allow self heating.
FN3393 Rev 9.00
September 30, 2015
Page 4 of 17
HA5023
Test Circuits and Waveforms
+
-
DUT
50
HP4195
NETWORK
ANALYZER
50
FIGURE 1. TEST CIRCUIT FOR TRANSIMPEDANCE MEASUREMENTS
(NOTE 12)
100
(NOTE 12)
100
VIN
+
VIN
DUT
VOUT
-
50
RL
100
RF, 1k
FIGURE 2. SMALL SIGNAL PULSE RESPONSE CIRCUIT
+
DUT
VOUT
-
50
RI
681
RF, 681
RL
400
FIGURE 3. LARGE SIGNAL PULSE RESPONSE CIRCUIT
NOTE:
12. A series input resistor of 100 is recommended to limit input currents in case input signals are present before the HA5023 is powered up.
Vertical Scale: VIN = 100mV/Div., VOUT = 100mV/Div.
Horizontal Scale: 20ns/Div.
FIGURE 4. SMALL SIGNAL RESPONSE
FN3393 Rev 9.00
September 30, 2015
Vertical Scale: VIN = 1V/Div., VOUT = 1V/Div.
Horizontal Scale: 50ns/Div.
FIGURE 5. LARGE SIGNAL RESPONSE
Page 5 of 17
HA5023
FN3393 Rev 9.00
September 30, 2015
Schematic Diagram
(One Amplifier of Two)
V+
R2
800
R5
2.5K
R10
820
QP8
R15
400
QP9
R19
400
QP11
QP1
QP5
QP14
R11
1K
R17
280
QN5
QP15
QN12
R1
60K
QP4
R28
20
QP17
QN13
+IN
QN17
QP13
C2
1.4pF
QN2
QP7
QN4
R14
280
R13
1K
QN7
R25
20
QN15
R21
140
QN10
QN3
QP20
R20
140
-IN
R12
280
R3
6K
D1
QP16
QP12
QP6
QN6
QN1
R24
140
C1
1.4pF
QN8
QP2
QP19
R31
5
R18
280
QP10
R29
9.5
R27
200
R22
280
QN21
R25
140
QN18
QN14
QN16
R16
400
R23
400
R26
200
R32
5
QN19
R30
7
OUT
R4
800
V-
R33
800
R9
820
QN9
QN11
Page 6 of 17
HA5023
traces connected to -IN, and that connections to -IN be kept
as short as possible to minimize the capacitance from this
node to ground.
Application Information
Optimum Feedback Resistor
The plots of inverting and non-inverting frequency response,
see Figure 8 and Figure 9 in the typical performance section,
illustrate the performance of the HA5023 in various closed
loop gain configurations. Although the bandwidth
dependency on closed loop gain isn’t as severe as that of a
voltage feedback amplifier, there can be an appreciable
decrease in bandwidth at higher gains. This decrease may
be minimized by taking advantage of the current feedback
amplifier’s unique relationship between bandwidth and RF.
All current feedback amplifiers require a feedback resistor,
even for unity gain applications, and RF, in conjunction with
the internal compensation capacitor, sets the dominant pole
of the frequency response. Thus, the amplifier’s bandwidth is
inversely proportional to RF. The HA5023 design is
optimized for a 1000 RF at a gain of +1. Decreasing RF in
a unity gain application decreases stability, resulting in
excessive peaking and overshoot. At higher gains the
amplifier is more stable, so RF can be decreased in a tradeoff of stability for bandwidth.
The table below lists recommended RF values for various
gains, and the expected bandwidth.
Driving Capacitive Loads
Capacitive loads will degrade the amplifier’s phase margin
resulting in frequency response peaking and possible
oscillations. In most cases the oscillation can be avoided by
placing an isolation resistor (R) in series with the output as
shown in Figure 6.
100
VIN
R
+
VOUT
-
RT
CL
RF
RI
FIGURE 6. PLACEMENT OF THE OUTPUT ISOLATION
RESISTOR, R
The selection criteria for the isolation resistor is highly
dependent on the load, but 27 has been determined to be
a good starting value.
Power Dissipation Considerations
RF ()
BANDWIDTH
(MHz)
-1
750
100
+1
1000
125
+2
681
95
+5
1000
52
+10
383
65
-10
750
22
PC Board Layout
The frequency response of this amplifier depends greatly on
the amount of care taken in designing the PC board. The use
of low inductance components such as chip resistors and
chip capacitors is strongly recommended. If leaded
components are used the leads must be kept short
especially for the power supply decoupling components and
those components connected to the inverting input.
Attention must be given to decoupling the power supplies. A
large value (10F) tantalum or electrolytic capacitor in
parallel with a small value (0.1F) chip capacitor works well
in most cases.
A ground plane is strongly recommended to control noise.
Care must also be taken to minimize the capacitance to
ground seen by the amplifier’s inverting input (-IN). The
larger this capacitance, the worse the gain peaking, resulting
in pulse overshoot and possible instability. It is
recommended that the ground plane be removed under
FN3393 Rev 9.00
September 30, 2015
Due to the high supply current inherent in dual amplifiers, care
must be taken to insure that the maximum junction
temperature (TJ , see Absolute Maximum Ratings) is not
exceeded. Figure 7 shows the maximum ambient
temperature versus supply voltage for the available package
styles (Plastic DIP, SOIC). At 5VDC quiescent operation both
package styles may be operated over the full industrial range
of -40°C to 85°C. It is recommended that thermal calculations,
which take into account output power, be performed by the
designer.
MAX AMBIENT TEMPERATURE (°C)
GAIN
(ACL)
140
130
120
PDIP
110
100
90
SOIC
80
70
60
50
5
7
9
11
13
15
SUPPLY VOLTAGE (V)
FIGURE 7. MAXIMUM OPERATING AMBIENT TEMPERATURE
vs SUPPLY VOLTAGE
Page 7 of 17
HA5023
Typical Performance Curves
VSUPPLY = 5V, AV = +1, RF = 1k RL = 400 TA = 25°C,
Unless Otherwise Specified
5
5
VOUT = 0.2VP-P
CL = 10pF
AV = 2, RF = 681
3
2
3
AV = 5, RF = 1k
1
0
-1
-2
-3
VOUT = 0.2VP-P
CL = 10pF
RF = 750
4
NORMALIZED GAIN (dB)
AV = 10, RF = 383
-4
2
1
AV = -2
0
-1
-2
AV = -10
-3
AV = -5
-4
-5
10
100
-5
200
FREQUENCY (MHz)
2
180
AV = +1, RF = 1k
135
-45
-90
90
AV = -1, RF = 750
-135
45
AV = +10, RF = 383
-100
0
-225
-45
-270
-90
AV = -10, RF = 750
-315
140
VOUT = 0.2VP-P
CL = 10pF
AV = +1
130
120
10
100
5
GAIN PEAKING
500
200
700
FREQUENCY (MHz)
10
5
350
500
650
800
950
0
1100
GAIN PEAKING (dB)
-3dB BANDWIDTH
FEEDBACK RESISTOR ()
FIGURE 12. BANDWIDTH AND GAIN PEAKING vs FEEDBACK
RESISTANCE
FN3393 Rev 9.00
September 30, 2015
-3dB BANDWIDTH (MHz)
95
GAIN PEAKING
0
1500
130
VOUT = 0.2VP-P
CL = 10pF
AV = +2
90
900
1100
1300
FEEDBACK RESISTOR ()
FIGURE 11. BANDWIDTH AND GAIN PEAKING vs FEEDBACK
RESISTANCE
FIGURE 10. PHASE RESPONSE AS A FUNCTION OF
FREQUENCY
100
10
-3dB BANDWIDTH
-180
2
200
-135
VOUT = 0.2VP-P
CL = 10pF
-360
INVERTING PHASE (°)
NONINVERTING PHASE (°)
0
100
FIGURE 9. INVERTING FREQUENCY RESPONSE
-3dB BANDWIDTH (MHz)
FIGURE 8. NON-INVERTING FREQENCY RESPONSE
10
FREQUENCY (MHz)
GAIN PEAKING (dB)
2
-3dB BANDWIDTH (MHz)
AV = -1
120
-3dB BANDWIDTH
110
6
100
4
90
GAIN PEAKING
80
0
200
400
VOUT = 0.2VP-P
CL = 10pF
AV = +1
600
800
2
0
1000
LOAD RESISTOR ()
FIGURE 13. BANDWIDTH AND GAIN PEAKING vs LOAD
RESISTANCE
Page 8 of 17
GAIN PEAKING (dB)
NORMALIZED GAIN (dB)
4
AV = +1, RF = 1k
HA5023
Typical Performance Curves
VSUPPLY = 5V, AV = +1, RF = 1k RL = 400 TA = 25°C,
Unless Otherwise Specified (Continued)
16
VOUT = 0.1VP-P
CL = 10pF
VOUT = 0.2VP-P
CL = 10pF
AV = +10
60
VSUPPLY = 5V, AV = +2
OVERSHOOT (%)
-3dB BANDWIDTH (MHz)
80
40
12
VSUPPLY = 15V, AV = +2
6
20
0
VSUPPLY = 5V, AV = +1
200
350
500
650
800
0
950
VSUPPLY = 15V, AV = +1
0
200
400
600
LOAD RESISTANCE ()
FEEDBACK RESISTOR ()
0.08
0.10
FREQUENCY = 3.58MHz
0.08
DIFFERENTIAL PHASE (°)
DIFFERENTIAL GAIN (%)
FREQUENCY = 3.58MHz
RL = 75
0.06
RL = 150
0.04
0.02
0.06
0.04
RL = 150
RL = 75
0.02
RL = 1k
RL = 1k
0.00
3
5
7
9
11
13
3
15
5
SUPPLY VOLTAGE (V)
-40
VOUT = 2.0VP-P
CL = 30pF
0
REJECTION RATIO (dB)
HD2
-60
3RD ORDER IMD
HD2
HD3
-80
1
FREQUENCY (MHz)
FIGURE 18. DISTORTION vs FREQUENCY
FN3393 Rev 9.00
September 30, 2015
15
AV = +1
-20
-30
-40
-50
CMRR
-60
NEGATIVE PSRR
-70
-80
HD3
-90
0.3
13
-10
-50
-70
7
9
11
SUPPLY VOLTAGE (V)
FIGURE 17. DIFFERENTIAL PHASE vs SUPPLY VOLTAGE
FIGURE 16. DIFFERENTIAL GAIN vs SUPPLY VOLTAGE
DISTORTION (dBc)
1000
FIGURE 15. SMALL SIGNAL OVERSHOOT vs LOAD
RESISTANCE
FIGURE 14. BANDWIDTH vs FEEDBACK RESISTANCE
0.00
800
10
0.001
POSITIVE PSRR
0.01
0.1
1
10
FREQUENCY (MHz)
FIGURE 19. REJECTION RATIOS vs FREQUENCY
Page 9 of 17
30
HA5023
Typical Performance Curves
VSUPPLY = 5V, AV = +1, RF = 1k RL = 400 TA = 25°C,
Unless Otherwise Specified (Continued)
12
8.0
RLOAD = 100
VOUT = 1.0VP-P
PROPAGATION DELAY (ns)
7.5
7.0
6.5
6.0
-50
-25
0
25
50
75
100
10
AV = +10, RF = 383
8
AV = +2, RF = 681
6
AV = +1, RF = 1k
4
125
3
5
7
9
11
SUPPLY VOLTAGE (V)
TEMPERATURE (C)
FIGURE 20. PROPAGATION DELAY vs TEMPERATURE
VOUT = 0.2VP-P
CL = 10pF
0.6
+ SLEW RATE
NORMALIZED GAIN (dB)
SLEW RATE (V/s)
0.8
VOUT = 2VP-P
400
350
- SLEW RATE
300
250
200
150
0.4
0.2
AV = +2, RF = 681
0
-0.2
-0.4
AV = +5, RF = 1k
-0.6
AV = +1, RF = 1k
-0.8
-1.0
100
-50
-25
0
25
50
75
100
AV = +10, RF = 383
-1.2
125
5
10
TEMPERATURE (°C)
FIGURE 22. FIGURE 22. SLEW RATE vs TEMPERATURE
VOLTAGE NOISE (nV/Hz)
NORMALIZED GAIN (dB)
0
AV = -1
-0.2
-0.4
-0.6
AV = -5
-0.8
-1.2
10
15
20
25
30
FREQUENCY (MHz)
FIGURE 24. INVERTING GAIN FLATNESS vs FREQUENCY
FN3393 Rev 9.00
September 30, 2015
1000
-INPUT NOISE CURRENT
80
800
600
60
+INPUT NOISE CURRENT
400
40
INPUT NOISE VOLTAGE
200
20
AV = -2
AV = -10
5
30
AV = +10, RF = 383
0.2
-1.0
25
100
VOUT = 0.2VP-P
CL = 10pF
RF = 750
0.4
15
20
FREQUENCY (MHz)
FIGURE 23. NON-INVERTING GAIN FLATNESS vs FREQUENCY
0.8
0.6
15
FIGURE 21. PROPAGATION DELAY vs SUPPLY VOLTAGE
500
450
13
0
0.01
0.1
1
FREQUENCY (kHz)
10
0
100
FIGURE 25. INPUT NOISE CHARACTERISTICS
Page 10 of 17
CURRENT NOISE (pA/Hz)
PROPAGATION DELAY (ns)
RL = 100
VOUT = 1.0VP-P
AV = +1
HA5023
Typical Performance Curves
VSUPPLY = 5V, AV = +1, RF = 1k RL = 400 TA = 25°C,
Unless Otherwise Specified (Continued)
1.5
BIAS CURRENT (A)
2
VIO (mV)
1.0
0.5
0.0
-60
-40
-20
0
20
40
60
80
100
120
0
-2
-4
-60
140
-40
-20
0
TEMPERATURE (°C)
TRANSIMPEDANCE (k)
BIAS CURRENT (A)
60
80
100
120
140
4000
22
20
18
16
-60
-40
-20
0
20
40
60
80
100
120
140
3000
2000
1000
-60
-40
-20
0
TEMPERATURE (°C)
20
40
60
80
100
120
140
TEMPERATURE (°C)
FIGURE 28. -INPUT BIAS CURRENT vs TEMPERATURE
FIGURE 29. TRANSIMPEDANCE vs TEMPERATURE
74
25
+PSRR
72
20
REJECTION RATIO (dB)
125°C
ICC (mA)
40
FIGURE 27. +INPUT BIAS CURRENT vs TEMPERATURE
FIGURE 26. INPUT OFFSET VOLTAGE vs TEMPERATURE
55°C
15
10
3
4
5
6
7
8
9
10
11
12
13
14
SUPPLY VOLTAGE (V)
FIGURE 30. SUPPLY CURRENT vs SUPPLY VOLTAGE
FN3393 Rev 9.00
September 30, 2015
70
68
-PSRR
66
64
62
CMRR
60
25°C
5
20
TEMPERATURE (°C)
15
58
-100
-50
0
50
100
150
200
TEMPERATURE (°C)
FIGURE 31. REJECTION RATIO vs TEMPERATURE
Page 11 of 17
250
HA5023
Typical Performance Curves
VSUPPLY = 5V, AV = +1, RF = 1k RL = 400 TA = 25°C,
Unless Otherwise Specified (Continued)
4.0
30
+15V
+10V
+5V
OUTPUT SWING (V)
SUPPLY CURRENT (mA)
40
20
3.8
10
0
0
1
2
3
4
5
6
7
8
9
3.6
-60
10 11 12 13 14 15
-40
-20
0
DISABLE INPUT VOLTAGE (V)
20
40
60
80
100
120
140
TEMPERATURE (°C)
FIGURE 32. SUPPLY CURRENT vs DISABLE INPUT VOLTAGE
FIGURE 33. OUTPUT SWING vs TEMPERATURE
30
1.2
VCC = 15V
1.1
VIO (mV)
VOUT (VP-P)
20
VCC = 10V
1.0
10
0.9
VCC = 4.5V
0.8
0
0.01
0.10
1.00
10.00
-60
-40
-20
LOAD RESISTANCE (k)
0
20
40
60
80
100
120
140
TEMPERATURE (°C)
FIGURE 34. OUTPUT SWING vs LOAD RESISTANCE
FIGURE 35. INPUT OFFSET VOLTAGE CHANGE BETWEEN
CHANNELS vs TEMPERATURE
-30
1.5
AV = +1
VOUT = 2VP-P
1.0
SEPARATION (dB)
BIAS CURRENT (A)
-40
0.5
-50
-60
-70
0.0
-60
-40
-20
0
20
40
60
80
100
120
TEMPERATURE (°C)
FIGURE 36. INPUT BIAS CURRENT CHANGE BETWEEN
CHANNELS vs TEMPERATURE
FN3393 Rev 9.00
September 30, 2015
140
-80
0.1
1
FREQUENCY (MHz)
10
FIGURE 37. CHANNEL SEPARATION vs FREQUENCY
Page 12 of 17
30
HA5023
Typical Performance Curves
VSUPPLY = 5V, AV = +1, RF = 1k RL = 400 TA = 25°C,
Unless Otherwise Specified (Continued)
-30
-40
-50
RL = 100
1
0.1
0.01
180
0.001
135
90
45
-60
0
-70
-45
-80
-90
0.1
1
FREQUENCY (MHz)
10
TRANSIMPEDANCE (M)
FIGURE 38. DISABLE FEEDTHROUGH vs FREQUENCY
20
0.001
0.01
0.1
1
FREQUENCY (MHz)
10
100
-135
FIGURE 39. TRANSIMPEDANCE vs FREQUENCY
10
RL = 400
1
0.1
0.01
180
0.001
135
90
45
0
-45
-90
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
-135
FIGURE 40. TRANSIMPEDENCE vs FREQUENCY
FN3393 Rev 9.00
September 30, 2015
PHASE ANGLE (°)
-20
10
PHASE ANGLE (°)
FEEDTHROUGH (dB)
-10
DISABLE = 0V
VIN = 5VP-P
RF = 750
TRANSIMPEDANCE (M)
0
Page 13 of 17
HA5023
SUBSTRATE POTENTIAL (Powered Up):
Die Characteristics
V-
DIE DIMENSIONS:
PASSIVATION:
1650m x 2540m x 483m
Type: Nitride
Thickness: 4kÅ 0.4kÅ
METALLIZATION:
Type: Metal 1: AlCu (1%)
Thickness: Metal 1: 8kÅ 0.4kÅ
TRANSISTOR COUNT:
124
Type: Metal 2: AlCu (1%)
Thickness: Metal 2: 16kÅ 0.8kÅ
PROCESS:
High Frequency Bipolar Dielectric Isolation
Metallization Mask Layout
HA5023
OUT
NC
V+
-IN1
+IN1
NC
OUT2
NC
V-
+IN
FN3393 Rev 9.00
September 30, 2015
-IN
Page 14 of 17
HA5023
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make
sure that you have the latest revision.
DATE
REVISION
September 30, 2015
FN3393.9
CHANGE
- Updated Ordering Information Table on page 1.
- Added Revision History.
- Added About Intersil Verbiage.
- Updated POD M8.15 to latest revision changes are as follow:
-Revision 1 to Revision 2 Changes:
Updated to new POD format by removing table and moving dimensions onto drawing and adding land
pattern
-Revision 2 to Revision 3 Changes:
Changed in Typical Recommended Land Pattern the following:
2.41(0.095) to 2.20(0.087)
0.76 (0.030) to 0.60(0.023)
0.200 to 5.20(0.205)
-Revision 3 to Revision 4 Changes:
Changed Note 1 "1982" to "1994"
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support.
© Copyright Intersil Americas LLC 1998-2015. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN3393 Rev 9.00
September 30, 2015
Page 15 of 17
HA5023
Dual-In-Line Plastic Packages (PDIP)
E8.3 (JEDEC MS-001-BA ISSUE D)
N
8 LEAD DUAL-IN-LINE PLASTIC PACKAGE
E1
INDEX
AREA
1 2 3
INCHES
N/2
-B-
-AD
E
BASE
PLANE
-C-
SEATING
PLANE
A2
A
L
D1
e
B1
D1
B
0.010 (0.25) M
A1
eC
C A B S
MILLIMETERS
SYMBOL
MIN
MAX
MIN
MAX
NOTES
A
-
0.210
-
5.33
4
A1
0.015
-
0.39
-
4
A2
0.115
0.195
2.93
4.95
-
B
0.014
0.022
0.356
0.558
-
C
L
B1
0.045
0.070
1.15
1.77
8, 10
eA
C
0.008
0.014
0.204
C
D
0.355
0.400
9.01
eB
NOTES:
1. Controlling Dimensions: INCH. In case of conflict between
English and Metric dimensions, the inch dimensions control.
0.005
-
0.13
-
5
E
0.300
0.325
7.62
8.25
6
E1
0.240
0.280
6.10
7.11
5
e
0.100 BSC
eA
0.300 BSC
3. Symbols are defined in the “MO Series Symbol List” in Section
2.2 of Publication No. 95.
eB
-
L
0.115
5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch
(0.25mm).
6. E and eA are measured with the leads constrained to be perpendicular to datum -C- .
5
D1
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
4. Dimensions A, A1 and L are measured with the package seated
in JEDEC seating plane gauge GS-3.
0.355
10.16
N
8
2.54 BSC
7.62 BSC
0.430
-
0.150
2.93
8
6
10.92
7
3.81
4
9
Rev. 0 12/93
7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions.
Dambar protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3,
E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch
(0.76 - 1.14mm).
FN3393 Rev 9.00
September 30, 2015
Page 16 of 17
HA5023
Package Outline Drawing
M8.15
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 4, 1/12
DETAIL "A"
1.27 (0.050)
0.40 (0.016)
INDEX
6.20 (0.244)
5.80 (0.228)
AREA
0.50 (0.20)
x 45°
0.25 (0.01)
4.00 (0.157)
3.80 (0.150)
1
2
8°
0°
3
0.25 (0.010)
0.19 (0.008)
SIDE VIEW “B”
TOP VIEW
2.20 (0.087)
SEATING PLANE
5.00 (0.197)
4.80 (0.189)
1.75 (0.069)
1.35 (0.053)
1
8
2
7
0.60 (0.023)
1.27 (0.050)
3
6
4
5
-C-
1.27 (0.050)
0.51(0.020)
0.33(0.013)
SIDE VIEW “A
0.25(0.010)
0.10(0.004)
5.20(0.205)
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1. Dimensioning and tolerancing per ANSI Y14.5M-1994.
2. Package length does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
3. Package width does not include interlead flash or protrusions. Interlead
flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.
4. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
5. Terminal numbers are shown for reference only.
6. The lead width as measured 0.36mm (0.014 inch) or greater above the
seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch).
7. Controlling dimension: MILLIMETER. Converted inch dimensions are not
necessarily exact.
8. This outline conforms to JEDEC publication MS-012-AA ISSUE C.
FN3393 Rev 9.00
September 30, 2015
Page 17 of 17
工商网监
湘ICP备2023018690号
