C192C222G1G5CA

Axial Leaded Multilayer Ceramic Capacitors Axial, Molded, C0G Dielectric, 50 – 200 VDC (Commercial Grade) Overview KEMET’s epoxy molded axial through-hole ceramic capacitors in C0G dielectric feature a 125°C maximum operating temperature. The Electronics Industries Alliance (EIA) characterizes C0G dielectric as a Class I “stable” material. Components of this classification are temperature compensating and are suited for resonant circuit applications or those where Q and stability of capacitance characteristics are required. C0G exhibits no change in capacitance with respect to time and voltage and boasts a negligible change in capacitance with reference to ambient temperature. Capacitance change is limited to ±30 ppm/°C from −55°C to +125°C. These devices meet the flame test requirements outlined in UL Standard 94 V–0. Benefits • Axial through-hole form factor • Molded case • −55°C to +125°C operating temperature range • DC voltage ratings of 50V, 100 V and 200 V • Capacitance offerings ranging from 1.0 pF up to 0.10 μF • Available capacitance tolerances of ±0.5 pF, ±1%, ±2%, ±5%, and ±10% • No piezoelectric noise • Extremely low ESR and ESL • High thermal stability • High ripple current capability • No capacitance change with respect to applied rated DC voltage • Negligible capacitance change with respect to temperature from −55°C to +125°C • No capacitance decay with time • Non-polar device, minimizing installation concerns • SnPb-plated lead finish (60/40) • Encapsulation meets flammability standard UL 94 V–0 Ordering Information 1 2 C 114 C 681 F 1 G 5 C A 7200 Ceramic Style /Size Specification /Series Capacitance Code (pF) Capacitance Tolerance1 Rated Voltage (VDC) Dielectric Design Lead Finish2 Failure Rate Packaging /Grade (C-Spec) 114 124 192 202 222 C= Standard Two significant digits and number of zeros Use 9 for 1.0 – 9.9 pF Use 8 for 0.5 – 0.99 pF ex. 2.2 pF = 229 ex. 0.5 pF = 508 G= C0G 5= Multilayer C = SnPb (60/40) A= N/A D = ±0.5 pF F = ±1% G = ±2% J = ±5% K = ±10% 5 = 50 V 1 = 100 V 2 = 200 V Blank = Bulk 7200 = 12" Reel 7293 = Ammo Pack Additional capacitance tolerance offerings may be available. Contact KEMET for details. Lead materials: Standard: 60% tin (Sn)/40% lead (Pb) finish with 100% copper core ( “C” designation). Alternative lead materials and finishes may be available. Contact KEMET for details. One world. One KEMET © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1045_C0G_AXIAL_MOLDED • 6/18/2019 1 Axial Leaded Multilayer Ceramic Capacitors Axial, Molded, C0G Dielectric, 50 – 200 VDC (Commercial Grade) Dimensions – Inches (Millimeters) 1.50 Minimum (38.10) L 1.50 Minimum (38.10) D C Series Style/Size L Length Maximum D Diameter Maximum LD Lead Diameter 114 124 192 202 222 0.160±0.010 (4.06±0.25) 0.250±0.010 (6.35±0.25) 0.390±0.010 (9.91±0.25) 0.500±0.020 (12.70±0.51) 0.690±0.030 (17.53±0.76) 0.090±0.010 (2.29±0.25) 0.090±0.010 (2.29±0.25) 0.140±0.010 (3.56±0.25) 0.250±0.015 (6.35±0.38) 0.350±0.020 (8.89±0.51) 0.020+0.0/−0.003 (0.51+0.0/−0.08) C1XX C2XX 0.025+0.004/−0.001 (0.64+0.10/−0.025) LL Lead Length Minimum 1.50 (38.10) Applications Typical applications include critical timing, tuning, circuits requiring low loss, circuits with pulse, high current, decoupling, bypass, filtering, transient voltage suppression, blocking and energy storage. Application Notes These devices are not recommended for use in overmold applications and/or processes. Qualification/Certification Commercial Grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in Table 2, Performance & Reliability. Environmental Compliance These devices do not meet RoHS criteria due to the concentration of Pb containment in the lead finish. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1045_C0G_AXIAL_MOLDED • 6/18/2019 2 Axial Leaded Multilayer Ceramic Capacitors Axial, Molded, C0G Dielectric, 50 – 200 VDC (Commercial Grade) Electrical Parameters/Characteristics Item Parameters/Characteristics Operating Temperature Range Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC) Aging Rate (Max % Cap Loss/Decade Hour) Dielectric Withstanding Voltage Dissipation Factor (DF) Maximum Limit at 25°C Insulation Resistance (IR) Limit at 25°C −55°C to +125°C ±30 ppm/°C 0% 250% of rated voltage (5 ±1 second and charge/discharge not exceeding 50 mA) 0.1% 1,000 megohm microfarads or 100 GΩ (Rated voltage applied for 120 ±5 seconds at 25°C) To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits. Capacitance and dissipation factor (DF) measured under the following conditions: 1 MHz ±100 kHz and 1.0 Vrms ±0.2 V if capacitance ≤ 1,000 pF 1 kHz ±50 Hz and 1.0 Vrms ±0.2 V if capacitance > 1,000 pF Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON." Post Environmental Limits High Temperature Life, Biased Humidity, Moisture Resistance Dielectric Rated DC Voltage Capacitance Value DF (%) Capacitance Shift C0G All All 0.5 0.3% or ±0.25 pF © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1045_C0G_AXIAL_MOLDED • 6/18/2019 3 Axial Leaded Multilayer Ceramic Capacitors Axial, Molded, C0G Dielectric, 50 – 200 VDC (Commercial Grade) Table 1A – C114 Style/Size (0.090" Diameter x 0.160" L), Capacitance Range Waterfall C114 Style/Size (0.090" Diameter x 0.160" L) Rated Voltage (VDC) 50 100 200 Voltage Code 5 1 2 Capacitance Tolerance Capacitance 1pF 1.5pF 2.2pF 2.7pF 3.3pF 3.9pF 4.7pF 5.6pF 6.8pF 8.2pF 10pF 12pF 15pF 18pF 22pF 27pF 33pF 39pF 47pF 56pF 68pF 82pF 100pF 120pF 150pF 180pF 220pF 270pF 330pF 390pF 470pF 560pF 680pF Capacitance Code (Available Capacitance) 109 159 229 279 339 399 479 569 689 829 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 109 159 229 279 339 399 479 569 689 829 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 109 159 229 279 339 399 479 569 689 829 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 Rated Voltage (VDC) 50 100 200 Voltage Code 5 1 2 D = ±0.5pF J = ±5% K = ±10% G = ±2% J = ±5% K = ±10% F = ±1% G = ±2% J = ±5% K = ±10% © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1045_C0G_AXIAL_MOLDED • 6/18/2019 4 Axial Leaded Multilayer Ceramic Capacitors Axial, Molded, C0G Dielectric, 50 – 200 VDC (Commercial Grade) Table 1B – C124 Style/Size (0.090" Diameter x 0.250" L), Capacitance Range Waterfall C124 Style/Size (0.090" Diameter x 0.250" L) Rated Voltage (VDC) 50 100 200 Voltage Code 5 1 2 Capacitance Capacitance Tolerance 390pF 470pF 560pF 680pF 820pF 1000pF F = ±1% G = ±2% J = ±5% K = ±10% Capacitance Code (Available Capacitance) 391 471 561 391 471 561 391 471 561 821 102 821 102 Rated Voltage (VDC) 50 100 200 Voltage Code 5 1 2 Table 1C – C192 Style/Size (0.140" Diameter x 0.390" L), Capacitance Range Waterfall C192 Style/Size (0.140" Diameter x 0.390" L) Rated Voltage (VDC) 50 100 200 Voltage Code 5 1 2 Capacitance 680pF 820pF 1000pF 1200pF 1500pF 1800pF 2200pF 2700pF 3300pF 2700pF 3300pF 3900pF 4700pF 5600pF 6800pF 8200pF Capacitance Tolerance Capacitance Code (Available Capacitance) 681 821 102 122 152 182 222 272 332 272 332 392 472 562 682 822 681 821 102 122 152 182 222 272 332 272 332 392 472 562 682 822 681 821 102 122 152 182 222 272 332 272 332 392 472 Rated Voltage (VDC) 50 100 200 Voltage Code 5 1 2 F = ±1% G = ±2% J = ±5% K = ±10% © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1045_C0G_AXIAL_MOLDED • 6/18/2019 5 Axial Leaded Multilayer Ceramic Capacitors Axial, Molded, C0G Dielectric, 50 – 200 VDC (Commercial Grade) Table 1D – C202 Style/Size (0.250" Diameter x 0.500" L), Capacitance Range Waterfall C202 Style/Size (0.250" Diameter x 0.500" L) Rated Voltage (VDC) 50 100 200 Voltage Code 5 1 2 Capacitance 5600pF 6800pF 8200pF 0.01µF 0.012µF 0.015µF 0.018µF 0.022µF 0.027µF 0.033µF Capacitance Tolerance Capacitance Code (Available Capacitance) 562 682 822 103 123 153 183 223 273 333 562 682 822 103 123 153 183 223 273 333 562 682 822 103 123 153 183 223 Rated Voltage (VDC) 50 100 200 Voltage Code 5 1 2 F = ±1% G = ±2% J = ±5% K = ±10% Table 1E – C222 Style/Size (0.350" Diameter x 0.690" L), Capacitance Range Waterfall C222 Style/Size (0.350" Diameter x 0.690" L) Rated Voltage (VDC) 50 100 200 Voltage Code 5 1 2 Capacitance 0.027µF 0.033µF 0.039µF 0.047µF 0.056µF 0.068µF 0.082µF 0.1µF Capacitance Tolerance Capacitance Code (Available Capacitance) 273 333 393 473 563 683 823 104 273 333 393 473 563 683 823 104 273 333 393 473 Rated Voltage (VDC) 50 100 200 Voltage Code 5 1 2 F = ±1% G = ±2% J = ±5% K = ±10% © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1045_C0G_AXIAL_MOLDED • 6/18/2019 6 Axial Leaded Multilayer Ceramic Capacitors Axial, Molded, C0G Dielectric, 50 – 200 VDC (Commercial Grade) Soldering Process Recommended Soldering Technique: • Solder Wave • Hand Soldering (Manual) Recommended Soldering Profile: • Optimum Wave Solder Profile Solder Wave Peak Temperature 260ºC Entrance to Solder Wave Degrees – Cº Flux Zone 250 225 200 175 150 125 100 75 50 25 Exit from Solder Wave (Time in Wave – 2 to 4 Seconds) Preheat Zone Hot Air Debridging Exit from Solder Machine 80ºC to 120ºC Entrance to Solder Machine Free Air Cool Bottom Side Temperature Range Entrance to In-Line Cleaner Exit from In-Line Cleaner (time in cleaner may be less) Immersion in Cleaning Vapor 150ºC Maximum Top Side Nominal 0 1 2 3 Time (Minutes) 4 5 6 • Hand Soldering (Manual) Manual Solder Profile with Pre-heating Soldering Gradual Cooling Gradual Preheat 60 – 120 Seconds Recommend 2.5°C/second Maximum 3 seconds Delta T < = 120ºC KEMET recommends following the guidelines and techniques outlined in technical bulletins F2103 and F9207. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1045_C0G_AXIAL_MOLDED • 6/18/2019 7 Axial Leaded Multilayer Ceramic Capacitors Axial, Molded, C0G Dielectric, 50 – 200 VDC (Commercial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions Stress Reference Test or Inspection Method Magnification 50 X. Conditions: Solderability J–STD–002 a) Method B, 4 hours at 155°C, dry heat at 235°C b) Method B at 215°C category 3 c) Method D, category 3 at 260°C Temperature Cycling Biased Humidity Moisture Resistance Thermal Shock High Temperature Life Storage Life Vibration Resistance to Soldering Heat Terminal Strength Mechanical Shock Resistance to Solvents JESD22 Method JA–104 MIL–STD–202 Method 103 MIL–STD–202 Method 106 MIL–STD–202 Method 107 MIL–STD–202 Method 108 /EIA–198 MIL–STD–202 Method 108 MIL–STD–202 Method 204 MIL–STD–202 Method 210 MIL–STD–202 Method 211 MIL–STD–202 Method 213 MIL–STD–202 Method 215 1,000 cycles (−55°C to +125°C), Measurement at 24 hours. +/−2 hours after test conclusion. Load Humidity: 1,000 hours 85°C/85% RH and Rated Voltage. Add 100 K ohm resistor. Measurement at 24 hours. +/−2 hours after test conclusion. Low Volt Humidity: 1,000 hours 85°C/85% RH and 1.5 V. Add 100 K ohm resistor. Measurement at 24 hours. +/−2 hours after test conclusion. t = 24 hours/cycle. Steps 7a and 7b not required. Unpowered. Measurement at 24 hours. +/−2 hours after test conclusion. −55°C/+125°C. Note: Number of cycles required – 300. Maximum transfer time – 20 seconds. Dwell time – 15 minutes. Air – Air. 1,000 hours at 125°C (85°C for X5R, Z5U and Y5V) with 2 X rated voltage applied. 150°C, 0 VDC, for 1,000 hours. 5 g for 20 minutes, 12 cycles each of 3 orientations. Note: Use 8"X5" PCB .031" thick 7 secure points on one long side and 2 secure points at corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10–2,000 Hz. Condition B. No pre-heat of samples. Note: single wave solder - procedure 2. Conditions A (2.3kg or 5 lbs) Figure 1 of Method 213, Condition F. Add aqueous wash chemical, OKEM Clean or equivalent. Storage & Handling Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperature-reels may soften or warp, and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40°C, and maximum storage humidity not exceed 70% relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts, and atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability, chip stock should be used promptly, preferably within 1.5 years of receipt. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1045_C0G_AXIAL_MOLDED • 6/18/2019 8 Axial Leaded Multilayer Ceramic Capacitors Axial, Molded, C0G Dielectric, 50 – 200 VDC (Commercial Grade) Packaging Details Lead Spacing Component Pitch (P1) 0.100 (2.54) 5.08 0.200 (5.08) 3.81 0.400 (10.16) 7.62 0.170 (4.32) 0.220 (5.59) 0.275 (6.98) 0.300 (7.62) 0.375 (9.52) 0.475 (12.06) 0.575 (14.60) 0.675 (17.14) Packaging Quantities Ammo Pack Quantity Maximum Reel Quantity Maximum (12" Reel) Style/Size Standard Bulk Quantity 114 200/Box 5000 124 200/Box 5000 192 100/Box 202 25/Box 500 222 10/Tray 300 N/A 3000 Marking © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1045_C0G_AXIAL_MOLDED • 6/18/2019 9 Axial Leaded Multilayer Ceramic Capacitors Axial, Molded, C0G Dielectric, 50 – 200 VDC (Commercial Grade) Tape & Reel Packaging Information KEMET offers standard reeling of molded and conformally coated axial leaded ceramic capacitors for automatic insertion or lead forming machines in accordance with EIA standard 296. KEMET’s internal specifi cation four-digit suffi x, 7200, is placed at the end of the part number to designate tape and reel packaging, e.g., C410C104Z5U5CA7200. Paper (50 lb.) test minimum is inserted between the layers of capacitors wound on reels for component pitch ≤ 0.400". Capacitor lead length may extend only a maximum of .0625" (1.59 mm) beyond the tapes’ edges. Capacitors are centered in a row between the two tapes and will deviate only ± 0.031" (0.79 mm) from the row center. A minimum of 36" (91.5 cm) leader tape is provided at each fi nished length of taped components. Universal splicing clips are used to connect the tape. Table 3 – Ceramic Axial Tape and Reel Dimensions Metric will govern Dimensions — Millimeters (Inches) Axial Capacitor Body Diameter 0.0 to 5.0 (0.0 to 0.197) A ±0.5 (0.020) B ±1.5 (0.059)* 5.0 (0.197) 52.4 (2.062) Symbol Reference Table A B Component Pitch Inside Tape Spacing * Inside tape spacing dimension (B) is determined by the body diameter of the capacitor. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1045_C0G_AXIAL_MOLDED • 6/18/2019 10 Axial Leaded Multilayer Ceramic Capacitors Axial, Molded, C0G Dielectric, 50 – 200 VDC (Commercial Grade) KEMET Electronics Corporation Sales Offices For a complete list of our global sales offi ces, please visit www.kemet.com/sales. Disclaimer All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1045_C0G_AXIAL_MOLDED • 6/18/2019 11