Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc,
Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Overview
KEMET’s 900 series encapsulated radial through-hole ceramic
disc capacitors are specifically designed for interferencesuppression AC line filtering applications. Having internationally
recognized safety certifications, these capacitors are well-suited
for applications that require keeping potentially disruptive or
damaging line transients and EMI out of susceptible equipment.
They are also an ideal solution when needing to suppress line
disturbances at the source.
With a working voltage of 400 VAC in line-to-line (Class X)and
250 VAC in line-to-ground (Class Y) applications, these safety
capacitors meet the impulse test criteria outlined in IEC Standard
60384. Meeting subclass X1 and Y2 requirements, these devices
are certified to withstand impulses up to 4 KV (X1) and 5 KV (Y2)
respectively. These encapsulated devices also meet the flame test
requirements outlined in UL Standard 94V-0.
Safety Certified Capacitors are classified as either X and/or Y
capacitors. Class X capacitors are primarily used in line-to line
(across-the-line) applications. In this application there is no
danger of electric shock to humans should the capacitor fail, but
could result in a risk of fire. The class Y capacitor is primarily
used in line-to-ground (line by-pass) applications. In this application, failure of the capacitor could lead to danger of electric
shock.
Ordering Information
C9
8
1
U
103
M
Y
Ceramic
Series
Body
Diameter
Lead
Spacing1,2,4
Spec.
Capacitance
Code (pF)
Capacitance
Tolerance
Rated
Voltage
2 significant
digits +
Number of
zeroes
Use 9 for
1.0 9.9 pF
e.g., 2.2 pF
= 229
C = ±0.25 pF Y = X1
D = ±0.5 pF 400 VAC
J = ±5%
/ Y2 250
K = ±10%
VAC
M = ±20%
C9 =
Ceramic
900
Series
0 = 7.0 mm 5 = 5.0 mm
U=
1 = 8.0 mm 7 = 7.5 mm Safety
2 = 9.0 mm 1 = 10.0 mm
3 = 10.0 mm
4 = 11.0 mm
6 = 13.0 mm
8 = 15.0 mm
V
D
A
A
Dielectric/
Lead
Failure
Design
Temp. Char.
Config.1,3,4 Rate
N = CH
(NP0)
S = SL
Y = Y5P
W = Y5U
V = Y5V
D=
Disc
A=
A=
Straight
N/A
B = Vertical
Kink
C=
Outside
Kink
D = Inside
Kink
7317
Packaging
(C-Spec)2,3,4
7317 = Ammo Pack
WL30 = Bulk/3.0 mm
Lead length
WL35 = Bulk/3.5 mm
Lead length
WL40 = Bulk/4.0 mm
Lead length
WL45 = Bulk/4.5 mm
Lead length
WL50 = Bulk/5.0 mm
Lead length
WL20 = Bulk/20 mm
Lead length
Due to a high risk of arcing, "Inside Kink" lead configuration cannot be combined with the 5 mm lead spacing option. The "Inside Kink" option is only available on
capacitors with lead spacing of 7.5 mm or 10 mm.
2
Capacitor body diameter will limit available lead spacing and packaging options. See "Dimensions" and "Product Ordering Codes and Ratings" sections of this
document to determine availability.
3
"Vertical Kink", "Outside Kink" and "Inside Kink" lead configurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead length is
only available on capacitors with straight leads (lead configuration ordering code "A"). For nonstandard lead length inquiries, please contact KEMET.
4
Bulk packaging lead length availability is dependent upon "Lead Configuration" and "Lead Spacing." See "Dimensions" section of this document to verify
availability of a specific lead length option. For nonstandard lead length inquiries, please contact KEMET.
1
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
1
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Lead Configurations
Straight
Vertical Kink
Outside Kink
Inside Kink1
1
Due to a high risk of arcing, the "Inside Kink" lead configuration option cannot me combined with 5 mm lead spacing ("F" dimension above). The "Inside Kink"
option is only available on devices with lead spacing of 7.5 mm or 10 mm.
Dimensions – Millimeters
Lead
Config.
Lead
F
Lead
Packaging
Config.
Spacing
Lead
Type2
Ordering
2 Tolerance
1
Spacing
Code
+0.8/-0.2
5.0
±0.8
Ammo Pack
Bulk
Ammo Pack
Straight
A
7.5
±1.0
Bulk
Ammo Pack
10.0
±1.0
Bulk
L
Lead
Length
Packaging
D
T
e
C-Spec
Body
Body
Lead
Ordering
2
3
Diameter
Thickness
Meniscus
Code
20.0 +1.5/-1.0
7317
3.0 ±1.0
WL30
3.5 ±1.0
WL35
4.5 ±1.0
WL45
20.0 minimum
WL20
20.0 +1.5/-1.0
7317
3.0 ±1.0
WL30
4.5 ±1.0
WL45
5.0 ±1.0
WL50
20.0 +1.5/-1.0
7317
3.0 ±1.0
WL30
4.5 ±1.0
WL45
5.0 ±1.0
WL50
See Table 1 - "Product
Ordering Codes and
Ratings"
3.0
maximum
Ød
Lead
Dia.
0.5 ±0.1
Lead Configuration is identified in the 13th character of the ordering code. See "Lead Configuration" and "Ordering Information" sections of this document for
further details.
2
Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for
further details.
3
The "Packaging C-Spec" is a 4-digit numeric or alphanumeric code which identifies both the packaging type and lead length requirement. When ordering, this
code must be included in the 15th through 18th character positions of the ordering code. See "Ordering Information" section of this document for further details.
1
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
2
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Dimensions – Millimeters cont'd
Lead
Config.
Lead
F
Lead
Packaging
Config.
Spacing
Lead
Type2
Ordering
2 Tolerance
1
Spacing
Code
+0.8/-0.2
5.0
Vertical Kink
(Preformed)
B
±0.8
Ammo Pack
±1.0
7317
3.0 ±1.0
WL30
3.5 ±1.0
WL35
4.0 ±1.0
WL40
18.0 +2.0/-0
7317
3.5 ±1.0
WL35
4.0 ±1.0
WL40
18.0 +2.0/-0
7317
3.5 ±1.0
WL35
4.0 ±1.0
WL40
18.0 +2.0/-0
7317
3.0 ±1.0
WL30
3.5 ±1.0
WL35
4.0 ±1.0
WL40
18.0 +2.0/-0
7317
3.5 ±1.0
WL35
4.0 ±1.0
WL40
5.0 ±1.0
WL50
18.0 +2.0/-0
7317
3.5 ±1.0
WL35
4.0 ±1.0
WL40
5.0 ±1.0
WL50
Ammo Pack
18.0 +2.0/-0
7317
Bulk
3.5 ±1.0
WL35
Ammo Pack
18.0 +2.0/-0
7317
Bulk
3.5 ±1.0
WL35
Bulk
Bulk
Ammo Pack
10.0
±1.0
+0.8/-0.2
5.0
±0.8
Bulk
Ammo Pack
Bulk
Ammo Pack
Outside Kink
(Preformed)
C
7.5
±1.0
Bulk
Ammo Pack
10.0
Inside Kink
(Preformed)
±1.0
7.5
D
±1.0
10
Lead
Length
Packaging
D
T
e
C-Spec
Body
Body
Lead
Ordering
2
3
Diameter
Thickness
Meniscus
Code
18.0 +2.0/-0
Ammo Pack
7.5
L
Bulk
Ød
Lead
Dia.
See Table 1 - "Product
Ordering Codes and
Ratings"
3.0
maximum
0.5 ±0.1
See Table 1 - "Product
Ordering Codes and
Ratings"
3.0
maximum
0.5 ±0.1
3.0
maximum
0.5 ±0.1
13.0
maximum
7.0
maximum
Lead Configuration is identified in the 13th character of the ordering code. See "Lead Configuration" and "Ordering Information" sections of this document for
further details.
2
Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for
further details.
3
The "Packaging C-Spec" is a 4-digit numeric or alphanumeric code which identifies both the packaging type and lead length requirement. When ordering, this
code must be included in the 15th through 18th character positions of the ordering code. See "Ordering Information" section of this document for further details.
1
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
3
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Benefits
•
•
•
•
•
•
•
•
•
•
•
•
Safety Standard Recognized (IEC 60384-14)
Reliable operation up to 125°C
Class X1/Y2
5.0 mm, 7.5 mm, and 10 mm lead spacing
Lead (Pb)-free and RoHS Compliant
Halogen Free
Capacitance offerings ranging from 2.0 pF up to 10,000 pF
Available capacitance tolerances of ±0.25 pF, ±0.5 pF, ±5%, ±10%, and ±20%
High reliability
Preformed (crimped) or straight lead configurations
Non-polar device, minimizing installation concerns
Encapsulation meets flammability standard UL 94V–0
Applications
Typical applications include:
• Line-to-line (Class X) filtering
• Line-to-ground (Class Y) filtering
• Antenna coupling
• Primary and secondary coupling (switching power supplies)
• Line disturbances suppression (motors and motor controls, relays, switching power supplies, and inverters)
Approval Standard and Certification No.
Safety Standard
Standard No.
VDE
(ENEC)
IEC 60384–14
Subclass
Working Voltage
X1
400 VAC
Y2
250 VAC
Certificate No.
40036415
These devices are VDE/ENEC recognized for antenna coupling and AC line-to-line (Class X) and line-to-ground (Class Y) applications per IEC60384–14.
Environmental Compliance
These devices are Halogen Free and RoHS Compliant. They meet all requirements set forth by both EU and China RoHS directives.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
4
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
General Specifications/Performance Characteristics
Dielectric/Temperature Characteristic:
CH(NP0)
SL
Y5P
Operating Temperature Range
Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC)
Y5U
Y5V
+20%/-55%
~ +30%/-80%
-40°C to +125°C
±60 ppm/ºC
-1,000 ~ +350
ppm/ºC
±10%
Dielectric Withstanding Voltage (7.5 mm and 10 mm Lead Spacing)1
2,600 VAC
(60 ±5 seconds at 25ºC)
Dielectric Withstanding Voltage (5 mm Lead Spacing)1
2,000 VAC
(60 ±5 seconds at 25ºC)
Quality Factor (Q)
Dissipation Factor (tanδ) at +25ºC2
Insulation Resistance (IR) Limit at +25°C
30 pF% and above: ≥ 1,000
Below 30 pF: ≥ 400 +(20 x C)*
See “Quality Factor”
See “Dissipation Factor”
2.50%
2.50%
5.0%
10,000 MΩ Minimum
(500 VDC applied for 60 ±5 seconds @ 25°C)
*C = Nominal capacitance
1
The distance between the adjacent leads of the component (also referred to as "lead spacing") governs Dielectric Withstanding Voltage (DWV) limit.
2
Capacitance and Dissipation Factor (DF) measured under the following conditions:
CH(NP0) & SL: 1 MHz ± 100 kHz and 1.0 ±0.2 Vrms
X5P, Y5U and Y5V: 1 kHz ± 50 Hz and 1.0 ±0.2 Vrms
Note: When measuring capacitance, it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as
Automatic Level Control (ALC). The ALC feature should be switched to "ON."
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
5
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Table 1 – Product Ordering Codes and Ratings
Dimensions (mm)
Dielectric/
Temp.
Char.
KEMET
Part Number
Capacitance
CH
(NP0)
C90(1)U209CYND(2)A(3)
C90(1)U309CYND(2)A(3)
C90(1)U409CYND(2)A(3)
C90(1)U509CYND(2)A(3)
C90(1)U609DYND(2)A(3)
C90(1)U709DYND(2)A(3)
C90(1)U809DYND(2)A(3)
C90(1)U909DYND(2)A(3)
C90(1)U100DYND(2)A(3)
C90(1)U120JYND(2)A(3)
C90(1)U150JYND(2)A(3)
C91(1)U180JYND(2)A(3)
C91(1)U200JYND(2)A(3)
C91(1)U220JYND(2)A(3)
C91(1)U240JYND(2)A(3)
C92(1)U270JYND(2)A(3)
C92(1)U300JYND(2)A(3)
C92(1)U330JYND(2)A(3)
C93(1)U360JYND(2)A(3)
C93(1)U390JYND(2)A(3)
C94(1)U470JYND(2)A(3)
2.0 pF
3.0 pF
4.0 pF
5.0 pF
6.0 pF
7.0 pF
8.0 pF
9.0 pF
10 pF
12 pF
15 pF
18 pF
20 pF
22 pF
24 pF
27 pF
30 pF
33 pF
36 pF
39 pF
47 pF
C90(1)U100JYSD(2)A(3)
C90(1)U120JYSD(2)A(3)
C90(1)U150JYSD(2)A(3)
C90(1)U180JYSD(2)A(3)
C90(1)U200JYSD(2)A(3)
C90(1)U220JYSD(2)A(3)
C90(1)U240JYSD(2)A(3)
C90(1)U270JYSD(2)A(3)
C90(1)U300JYSD(2)A(3)
C90(1)U330JYSD(2)A(3)
C90(1)U360JYSD(2)A(3)
C90(1)U390JYSD(2)A(3)
C90(1)U470JYSD(2)A(3)
C90(1)U500JYSD(2)A(3)
C90(1)U510JYSD(2)A(3)
C91(1)U560JYSD(2)A(3)
C91(1)U620JYSD(2)A(3)
C91(1)U680JYSD(2)A(3)
C91(1)U750JYSD(2)A(3)
C92(1)U820JYSD(2)A(3)
C93(1)U101JYSD(2)A(3)
10 pF
12 pF
15 pF
18 pF
20 pF
22 pF
24 pF
27 pF
30 pF
33 pF
36 pF
39 pF
47 pF
50 pF
51 pF
56 pF
62 pF
68 pF
75 pF
82 pF
100 pF
±5%
KEMET Part Number
Capacitance
Capacitance
Tolerance
SL
Capacitance
Tolerance
Lead Spacing
Body
Body
Lead
Diameter Thickness
Diameter
(Maximum) (Maximum)
Bulk
Packaging
Ammo
Packaging
±0.25 pF
7.0
±0.5 pF
5.0
0.5 ±0.1
5 mm,
7.5 mm,
or
10 mm
8.0
±5%
9.0
10.0
11.0
7.5 mm or 10 mm
7.0
5.0
0.5 ±0.1
5 mm,
7.5 mm,
or
10 mm
Body Thickness
(Maximum)
Lead Diameter
Lead Spacing
8.0
9.0
10.0
Body Diameter
(Maximum)
(1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging
options may limit lead spacing availability. See table above to verify availability.)
5 = 5.0 mm
7 = 7.5 mm
1 = 10.0 mm
(2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this
document, page 2, for further details.)
A = Straight
B = Vertical Kink
C = Outside Kink
D = Inside Kink (not available with 5 mm lead spacing option)
(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this
document, page 2, for available options.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
Roll Over for
Order Info.
6
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Table 1 – Product Ordering Codes and Ratings cont'd
Dimensions (mm)
Dielectric/
Temp.
Char.
KEMET
Part Number
Capacitance
Y5P
C90(1)U101KYYD(2)A(3)
C90(1)U151KYYD(2)A(3)
C90(1)U221KYYD(2)A(3)
C90(1)U331KYYD(2)A(3)
C90(1)U471KYYD(2)A(3)
C91(1)U561KYYD(2)A(3)
C91(1)U681KYYD(2)A(3)
C92(1)U821KYYD(2)A(3)
C92(1)U102KYYD(2)A(3)
100 pF
150 pF
220 pF
330 pF
470 pF
560 pF
680 pF
820 pF
1,000 pF
C90(1)U102MYWD(2)A(3)
C92(1)U152MYWD(2)A(3)
C92(1)U222MYWD(2)A(3)
C94(1)U332MYWD(2)A(3)
C96(1)U392MYWD(2)A(3)
C96(1)U472MYWD(2)A(3)
1,000 pF
1,500 pF
2,200 pF
3,300 pF
3,900 pF
4,700 pF
C90(1)U102MYVD(2)A(3)
C90(1)U152MYVD(2)A(3)
C90(1)U222MYVD(2)A(3)
C92(1)U332MYVD(2)A(3)
C94(1)U392MYVD(2)A(3)
C94(1)U472MYVD(2)A(3)
C96(1)U682MYVD(2)A(3)
C98(1)U103MYVD(2)A(3)
1,000 pF
1,500 pF
2,200 pF
3,300 pF
3,900 pF
4,700 pF
6,800 pF
10,000 pF
±20%
KEMET Part Number
Capacitance
Capacitance
Tolerance
Y5U
Y5V
Capacitance
Tolerance
Lead Spacing
Body
Body
Lead
Diameter Thickness
Diameter
(Maximum) (Maximum)
7.0
±10%
5.0
0.5 ±0.1
5.0
0.5 ±0.1
8.0
Bulk
Packaging
Ammo
Packaging
5 mm,
7.5 mm,
or
10 mm
9.0
7.0
9.0
±20%
11.0
5 mm, 7.5 mm, or 10 mm
7.5 mm or 10 mm
13.0
7.0
9.0
11.0
10 mm only
5 mm, 7.5 mm, or 10 mm
5.0
0.5 ±0.1
7.5 mm or 10 mm
13.0
15.0
Body Diameter
(Maximum)
7.5 mm or 10 mm
Body Thickness
(Maximum)
Lead Diameter
7.5 mm or 10 mm
10 mm only
Lead Spacing
(1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging
options may limit lead spacing availability. See table above to verify availability.)
5 = 5.0 mm
7 = 7.5 mm
1 = 10.0 mm
(2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this
document, page 2, for further details.)
A = Straight
B = Vertical Kink
C = Outside Kink
D = Inside Kink (not available with 5 mm lead spacing option)
(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this
document, page 2, for available options.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
Roll Over for
Order Info.
7
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Table 2 – Performance & Reliability: Test Methods and Conditions
Item
Specification
-40ºC to +125ºC
Operating Temperature Range
Between lead
wires
No failures
Body Insulation
No failures
Dielectric
Strength
Insulation Resistance (IR)
10,000 MΩ minimum
Capacitance
Within specified tolerance
Dissipation Factor (DF) or Q
Temperature Characteristics
Temperature
Characteristics
Specification
Y5P, Y5U
DF ≤ 2.5%
Y5V
DF ≤ 5.0%
NP0,SL
≥ 30 pF: Q ≥ 1000
< 30 pF: Q ≥ 400
+(20 x C)
C = Nominal
capacitance
Y5P, Y5U and Y5V: Capacitance is measured at 1 kHz ±20% and 5
Vrms or less. (20 ±2°C)
NP0 and SL: Capacitance is measured at 1 MHz ±20% and 1.0 ±0.2
Vrms (25°C)
A capacitance measurement is made at each step specified:
Capacitance
Change
Y5P
Within ±10%
2
-25 ±2ºC
Y5U
Within +20%/-55%
3
+20 ±2ºC
Y5V
Within ~+30%/-80%
4
+85 ±2ºC
CH
0 ±60 ppm/ºC
5
+20 ±2ºC
SL
-1,000 ~+350 ppmºC
(+20ºC ~+85ºC)
Lead wire or capacitor body shall not break.
Bending
Lead wire or capacitor body shall not break.
Terminal Strength
1
The capacitor shall not be damaged when voltage is applied between
the lead wires for 60 seconds.
2,000 VAC(rms) - 5.0 mm lead spacing
2,600 VAC(rms) - 7.5 mm and 10 mm lead spacing
The terminals (leads) of the capacitor shall
be connected together. A metal foil is tightly
wrapped around the body of the capacitor at a
distance of about 3 to 4 mm from each terminal.
The capacitor is then inserted into a container
filled with metal balls approximately 1 mm in
diameter. 2,600 VAC(rms) is applied for 60
seconds between the capacitor lead wires and
metal balls.
The insulation resistance shall be measured with 500 ±50 VDC applied
after 60 ±5 seconds of charging.
Temperature
Characteristics
Tensile
Solderability
Test Method
Lead wire should have a uniform coating of
solder in the axial direction and over 3/4 of its
circumference.
Step
Temperature
1
+20 ±2ºC
Pre-treatment:
Capacitor is stored at 85 ±2ºC for 1 hour and then placed at room
condition1 for 24 ±2 hours before measurement.
With the termination in its normal position, the specimen is held by its
body in such a manner that the axis of the termination is vertical; a
tensile force of 10 N is applied to the termination in the direction of its
axis and acting in a direction away from the body of the specimen.
With the termination in its normal position, the specimen is held by its
body in such a manner that the axis of the termination is vertical; a
mass force of 5 N is then suspended from the end of the termination.
The body of the specimen is then inclined within a period of 2 to 3
seconds, through an angle of approximately 90° in the vertical plane
and then resumed to its initial position over the same period of time;
this operation constitutes one bend. One bend immediately followed by
a second bend in the opposite direction.
The lead wire of the capacitor is dipped into molten solder for 2 ±0.5
seconds. The depth of immersion is up to 1.5 mm (+5/-0 mm) from the
root of lead wires.
Solder Temperature: Lead free solder (Sn-3Ag – 0.5Cu) 245°C ±5°C.
“Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
8
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Table 2 – Performance & Reliability: Test Methods and Conditions cont'd
Item
Soldering Effect
(Non-Preheat)
Specification
Test Method
Appearance
No visual defect
IR
1,000 MΩ
Dielectric
Strength
Per item 1
As shown in the figure below, the lead wires are immersed in molten
solder up to 1.5 mm (+5/-0 mm) from the end of the epoxy meniscus
(root of lead wire).
Duration/Solder Temperature: 3.5 ±0.5 seconds/350°C ±10°C or 10 ±1
seconds/260°C ±5°C
Capacitance
Y5P, Y5U and Y5V: Within ±10%
SL, CH (NP0): Within ±2.5% or ±0.25 pF,
whichever is larger.
Appearance
No visual defect
IR
1,000 MΩ
Dielectric
Strength
Per item 1
Capacitance
Y5P, Y5U and Y5V: Within ±10%
SL, CH (NP0): Within ±2.5% or ±0.25 pF,
whichever is larger.
Soldering Effect
(Preheat)
Appearance
Capacitance
Biased Humidity
DF
Q
IR
Dielectric
Strength
1
No visual defect
Temperature
Characteristics
Capacitance
Change
Y5P
Within ±10%
Y5U
Within ±20%
Y5V
Within ±30%
SL CH (NP0)
Within ±2.5% or
±0.25 pF, whichever
is larger.
Y5P and Y5U: 5.0% maximum
Y5V: 7.5% maximum
SL and CH(NP0): Less than 30 pF:
Q ≥ 100 + 10 × C/3
More than 30 pF: Q ≥ 200
C = Nominal capacitance
Y5P, Y5V and Y5U: 3,000 MΩ minimum
SL and CH (NP0): 1,000 MΩ minimum
Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then
placed at room condition1 for 24 ±2 hours before initial measurements.
Post-treatment: Capacitor is stored for 1 to 2 hours at room
condition1.
Capacitor is stored at 120°C +0/-5°C for 60 +0/-5 seconds. Then, as
shown in the figure below, the lead wires are immersed in molten solder
up to 1.5 mm (+5/-0mm) from the end of the epoxy meniscus (root of
lead wire).
Duration/Solder Temperature: 7.5 +0/-1 seconds/260°C ±5°C
Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then
placed at room condition1 for 24 ±2 hours before initial measurements.
Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1.
Steady State Humidity:
Load Humidity:
90 to 95% humidity at 40°C
±2°C for 500 ±12 hours.
90 to 95% humidity at 40°C
±2°C for 500 ±12 hours with full
rated voltage applied.
Post Treatment:
Capacitor is stored for 1 to 2
hours at room condition1.
Post Treatment:
Capacitor is stored for 1 to 2
hours at room condition1.
No failures
“Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
9
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Table 2 – Performance & Reliability: Test Methods and Conditions cont'd
Specification
No visual defect
Appearance
Capacitance
Change
IR
High Temperature
Life
Y5P, Y5V and Y5U: Within ±20%
SL and CH (NP0): Within ±3 or ±0.3 pF,
whichever is larger.
3,000 MΩ minimum
SL and CH (NPO): 1,000 MΩ minimum
Dielectric
Strength
Test Method
Impulse Voltage: Each individual capacitor is subjected to three 5 kv
impulses prior to life testing.
0.9Vp
UPP
tr
(uS)
1.2
1.5
td
(uS)
46
47
0.5Vp
tr
No failures
Cx
(uF)
0.01
0.1
UPR
Vp
Voltage
Item
td
Time
Capacitors are placed in a circulating air oven for a period of 1,000
hours. The air in the oven is maintained at a temperature of 125°C ±2
throughout the test. The capacitors are subjected to AC 425 Vrms.
Each hour the voltage is increased to AC 1,000 Vrms for 0.1 seconds.
The capacitor is exposed to a flame for 15 seconds and then removed
for 15 seconds. This test is repeated for 5 cycles.
The capacitor flame extinguishes as follows:
Flame Test
Cycle
Time
1~4
30 seconds maximum
5
60 seconds maximum
The capacitors are individually wrapped in at least one, but not more
than two, complete layers of cheesecloth. They are then subjected
to 20 discharges. The interval between successive discharges is 5
seconds. The VAC is maintained for 2 minutes after the last discharge.
Active Flammability
1
The cheesecloth should not ignite.
C1, 2
1 μF ±10%
C3
0.033 μF ±5% 10 kV
L1-4
1.5 Mh ±20% 16A Rod core choke
Cx
Test capacitor
R
100 ±2%
VAC
VR ±5%
Ct
3 μF ±5% 10 kV
VR
Rated Voltage
F
Fuse, Rated 10A
Vt
Voltage applied to Ct
“Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
10
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Table 2 – Performance & Reliability: Test Methods and Conditions cont'd
Item
Specification
Test Method
The capacitor under test is held into a flame and in a position which
best promotes burning. Each specimen is exposed to the flame one
time.
Passive Flammability
The burning time should not exceed 30
seconds.
The tissue paper should not ignite.
Time of exposure to flame:
Length of flame:
Gas burner length:
Inside diameter:
Outside diameter:
Gas butane gas purity:
Appearance
Capacitance
Temperature
Cycle
No visual defect
Temperature
Characteristics
Capacitance
Change
SL, CH (NP0)
Within ±5%
Y5P
Within ±10%
Y5U, Y5V
Within ±20%
SL, CH (NP0)
≥ 30 pF: Q ≥ 350
< 30 pF: Q ≥ 275
+5/2C
C = Nominal
capacitance
DF/Q
1
30 seconds
12 ±1 mm
35 mm minimum
0.5 ±0.1 mm
0.9 mm maximum
95% minimum
Y5P
DF ≤ 5%
Y5U, Y5V
DF ≤ 7.5%
IR
3,000 MΩ minimum
Dielectric
Strength
No failures
The capacitor is subjected to 5 temperature cycles.
(Temperature Cycle)
Step
Temperature (°C)
Time
(minutes)
1
-40 +0/-3
30
2
Room temperature
3
3
125 +3/-0
30
4
Room temperature
3
Pre-treatment: Capacitor shall be stored at 85 ±2 for 1 hour then
placed at room condition1 for 24 ±2 hours.
Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1.
“Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
11
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Soldering and Mounting Information
Soldering:
When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this
product to excessive heating could reflow the solder joint between the lead and ceramic element and/or may result in thermal shocks
that can crack the ceramic element.
When soldering these capacitors with a soldering iron, it should be performed under the following conditions:
• Temperature of iron-tip: 400ºC maximum
• Soldering iron wattage: 50 W maximum
• Soldering time: 3.5 seconds maximum
Cleaning (ultrasonic cleaning):
To perform ultrasonic cleaning, observe the following conditions:
• Rinse bath capacity: Output of 20 watts per liter or less
• Rinsing time: 5 minute maximum
• Do not vibrate the PCB/PWB directly
• Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires
Construction
Reference
Item
Material
1
Encapsulation1
Epoxy resin, Pigment (Blue/UL 94 V–0)
2
Dielectric Material
BaTiO3
3
Solder
Sn 96.5, Ag 3, Cu 0.5
4
Electrodes
Ag (Glass frit)
Lead Wires
Tinned copper clad steel wire
(Sn Plating 100% 3-7 µm)
5
The minimum thickness of the insulation coating (encapsulation) is 0.4 mm
Note: Image is exaggerated in order to clearly identify all components of construction.
1
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
12
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Capacitor Marking
These capacitors shall be stamped or laser marked with KEMET's trademark, type designation, capacitor class, rated voltage, rated
capacitance, and capacitance tolerance codes. In addition, all devices are marked with the recognized approval mark and a date/lot
code for traceability. Marking will be supplied either on one side or both sides of the encapsulated capacitor body. All marking shall
be legible to allow for clear identification of the component. Marking appears in legible contrast. Illustrated below is an example of the
marking format and content. (Two sided marking is limited to capacitors with body diameters ≤ 8.0 mm.)
Location #
Description
Detail
❶
KEMET Trademark
❷
Type Designation
(2 characters)
AC
❸
Rated Capacitance
(3 numeric characters)
First two digits are the significant figures of capacitance. Third digit indicates the additional
number of zeros. For example, 4,700 pF is identified as 472. (For values below 10 pF an “R” is
used in place of the decimal point, e.g., 2R0 = 2.0 pF.)
❹
Capacitance Tolerance
Code (1 character)
C = 0.25 pF, D = 0.5 pF, J = ±5%, K = ±10%, M = ±20%
❺
VDE & ENEC approval mark
IEC 60384–14 3rd (2005)
❻
Capacitor Class and Rated
Voltage
X1: 400 V ~ Y2: 250 V ~
Date/Lot Code, e.g., 3C12345
❼
Date/Lot Code
3
C
1
2345
Last digit of year,
e.g.,
Manufacturing
Location Code
Manufacturing Month:
Last 4 digits of
lot no.
1-9 = Jan - Sept
A = October
N = November
D = December
3 = 2013
Packaging Quantities
1
Packaging Type
Loose (Bulk Bag)
Ammo Pack
N/A
Bulk
500 pieces/bag
Carrier Tape Quantity
(12.7 mm Pitch1)
(15 mm Pitch1)
1,000 pieces/box
(25.4 mm Pitch1)
500 pieces/box
N/A
For details regarding component pitch on carrier tape, see "Ammo Pack Taping Format" and "Ammo Pack Taping Specifications" sections of this document.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
13
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Figure 1 - Ammo Pack Taping Format
5 mm and 7.5 mm Lead Spacing:
10 mm Lead Spacing:
Table 3 – Ammo Pack Taping Specifications
Lead Spacing
5 mm
Lead Style
Item
Straight
Preformed1
Symbol
7.5 mm
Straight
Preformed1
10 mm
Straight
Preformed1
Dimensions (mm)
Lead Spacing
F
5.0 +0.8/-0.2
7.5 ±1.0
10.0 ±1.0
Component Pitch
P
12.7
15.0
25.4 ±2
Sprocket Hole Pitch
P0
12.7 ±0.3
15.0 ±0.3
12.7 ±0.3
Sprocket Hole Center to
Component Center
P2
6.35 ±1.5
7.5 ±1.5
12.7 ±1.5
Sprocket Hole Center to Lead Center
P1
3.75 ±1.0
3.75 ±1.0
7.7 ±1.5
Body Diameter
D
See "Product Ordering Codes and Ratings" section of this document.
Component Alignment (side/side)
∆S
0 ±2.0
Carrier Tape Width
W
18.0 +1.0/-0.5
Sprocket Hole Position
W1
9.0 ±0.5
Prefromed (crimped) lead configurations include vertical kink, outside kink and inside kink. See "Lead Configurations" and "Ordering Information" sections of this
document for further details.
2
Also referred to as "lead length" in this document.
1
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
14
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Table 3 – Ammo Pack Taping Specifications cont'd
Lead Spacing
5 mm
Lead Style
Item
Straight
7.5 mm
Preformed1
Symbol
Straight
10 mm
Preformed1
Straight
Preformed1
Dimensions (mm)
Height to Seating Plane2
(preformed leads1)
H0
N/A
18.0 +2.0/-0
N/A
18.0 +2.0/-0
N/A
18.0 +2.0/-0
Height to Seating Plane2
(straight leads)
H
20.0 +1.5/-1.0
N/A
20.0 +1.5/-1.0
N/A
20.0 +1.5/-1.0
N/A
Lead Protrusion
ℓ
2.0 maximum
Diameter of Sprocket Hole
D0
4.0 ±0.2
Lead Diameter
φd
0.5 ±0.1
Carrier Tape Thickness
t1
0.6 ±0.3
Total Thickness (Carrier Tape,
Hold-Down Tape and Lead)
t2
1.5 maximum
∆h1
∆h2
2.0 maximum
L
11.0 maximum
Component Alignment (front/back )
Cut Out Length
Hold-Down Tape Width
W0
11.0 minimum
11.5 minimum
Hold-Down Tape Position
W2
3.0 maximum
1.5 ±1.5
Coating Extension on Leads (meniscus)
e
3.0 maximum for straight lead; not to exceed the bend for preformed1 lead configurations.
Body Thickness
T
See "Product Ordering Codes and Ratings" section of this document.
Prefromed (crimped) lead configurations include vertical kink, outside kink and inside kink. See "Lead Configurations" and "Ordering Information" sections of this
document for further details.
2
Also referred to as "lead length" in this document.
1
Application Notes:
Storage and Operating Conditions:
The insulating coating of these devices does not form an air and moisture-tight seal. Avoid exposure to moisture and do not use or
store these devices in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt, or the like are present.
Before cleaning, bonding or molding these devices, it is important to verify that your process does not affect product quality and
performance. KEMET recommends testing and evaluating the performance of a cleaned, bonded or molded product prior to
implementing and/or qualifying any of these processes. Store the capacitors where the temperature and relative humidity do not
exceed 40 degrees Centigrade and 70% respectively. For optimum solderability, capacitor stock should be used promptly, preferably
within 6 months of receipt.
Working Voltage:
Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated for a
transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a capacitor with a
voltage rating greater than or equal to these irregular voltages.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
15
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Operating Temperature and Self-Generating Heat:
The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be sure to take
into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or similar
current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated heating should not exceed 20°C (while
operated at an atmosphere temperature of 25°C).
Handling - Vibration and Impact:
Do not expose these devices or their leads to excessive shock or vibration during use.
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR
PARTIAL DISPERSION WHEN THE PRODUCT IS USED.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
16
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Paris, France
Tel: 33-1-4646-1006
Northeast Asia
Hong Kong
Tel: 852-2305-1168
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
Sasso Marconi, Italy
Tel: 39-051-939111
Shenzhen, China
Tel: 86-755-2518-1306
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Corporate Offices
Fort Lauderdale, FL
Tel: 954-766-2800
Kamen, Germany
Tel: 49-2307-438110
North America
Northern Europe
Bishop’s Stortford, United Kingdom
Tel: 44-1279-460122
2835 KEMET Way
Simpsonville, SC 29681
Southeast
Lake Mary, FL
Tel: 407-855-8886
Northeast
Wilmington, MA
Tel: 978-658-1663
Espoo, Finland
Tel: 358-9-5406-5000
Beijing, China
Tel: 86-10-5829-1711
Shanghai, China
Tel: 86-21-6447-0707
Taipei, Taiwan
Tel: 886-2-27528585
Southeast Asia
Singapore
Tel: 65-6586-1900
Penang, Malaysia
Tel: 60-4-6430200
Bangalore, India
Tel: 91-806-53-76817
Central
Novi, MI
Tel: 248-994-1030
West
Milpitas, CA
Tel: 408-433-9950
Mexico
Guadalajara, Jalisco
Tel: 52-33-3123-2141
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
17
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)
Other KEMET Resources
Tools
Resource
Location
Configure A Part: CapEdge
http://capacitoredge.kemet.com
SPICE & FIT Software
http://www.kemet.com/spice
Search Our FAQs: KnowledgeEdge
http://www.kemet.com/keask
Electrolytic LifeCalculator
http://www.kemet.com:8080/elc
Product Information
Resource
Location
Products
Technical Resources (Including Soldering Techniques)
RoHS Statement
Quality Documents
http://www.kemet.com/products
http://www.kemet.com/technicalpapers
http://www.kemet.com/rohs
http://www.kemet.com/qualitydocuments
Product Request
Resource
Location
Sample Request
Engineering Kit Request
http://www.kemet.com/sample
http://www.kemet.com/kits
Contact
Resource
Location
Website
Contact Us
Investor Relations
www.kemet.com
http://www.kemet.com/contact
http://www.kemet.com/ir
Call Us
1-877-MyKEMET
Twitter
http://twitter.com/kemetcapacitors
Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are
not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use. The Information is intended for use only
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1064_X1_400 VAC_Y2_250 VAC • 11/14/2013
18
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
KEMET:
C907U209CYNDAA7317 C907U209CYNDAAWL20 C907U209CYNDAAWL35 C907U209CYNDAAWL40
C907U209CYNDAAWL45 C907U209CYNDBA7317 C907U209CYNDBAWL20 C907U209CYNDBAWL35
C907U209CYNDBAWL40 C907U209CYNDBAWL45 C907U209CYNDCA7317 C907U209CYNDCAWL20
C907U209CYNDCAWL35 C907U209CYNDCAWL40 C907U209CYNDCAWL45 C907U309CYNDAA7317
C907U309CYNDAAWL20 C907U309CYNDAAWL35 C907U309CYNDAAWL40 C907U309CYNDAAWL45
C907U309CYNDBA7317 C907U309CYNDBAWL20 C907U309CYNDBAWL35 C907U309CYNDBAWL40
C907U309CYNDBAWL45 C907U309CYNDCA7317 C907U309CYNDCAWL20 C907U309CYNDCAWL35
C907U309CYNDCAWL40 C907U309CYNDCAWL45 C907U409CYNDAA7317 C907U409CYNDAAWL20
C907U409CYNDAAWL35 C907U409CYNDAAWL40 C907U409CYNDAAWL45 C907U409CYNDBA7317
C907U409CYNDBAWL20 C907U409CYNDBAWL35 C907U409CYNDBAWL40 C907U409CYNDBAWL45
C907U409CYNDCA7317 C907U409CYNDCAWL20 C907U409CYNDCAWL35 C907U409CYNDCAWL40
C907U409CYNDCAWL45 C907U509CYNDAA7317 C907U509CYNDAAWL20 C907U509CYNDAAWL35
C907U509CYNDAAWL40 C907U509CYNDAAWL45 C907U509CYNDBA7317 C907U509CYNDBAWL20
C907U509CYNDBAWL35 C907U509CYNDBAWL40 C907U509CYNDBAWL45 C907U509CYNDCA7317
C907U509CYNDCAWL20 C907U509CYNDCAWL35 C907U509CYNDCAWL40 C907U509CYNDCAWL45
C907U609DYNDAA7317 C907U609DYNDAAWL20 C907U609DYNDAAWL35 C907U609DYNDAAWL40
C907U609DYNDAAWL45 C907U609DYNDBA7317 C907U609DYNDBAWL20 C907U609DYNDBAWL35
C907U609DYNDBAWL40 C907U609DYNDBAWL45 C907U609DYNDCA7317 C907U609DYNDCAWL20
C907U609DYNDCAWL35 C907U609DYNDCAWL40 C907U609DYNDCAWL45 C907U709DYNDAA7317
C907U709DYNDAAWL20 C907U709DYNDAAWL35 C907U709DYNDAAWL40 C907U709DYNDAAWL45
C907U709DYNDBA7317 C907U709DYNDBAWL20 C907U709DYNDBAWL35 C907U709DYNDBAWL40
C907U709DYNDBAWL45 C907U709DYNDCA7317 C907U709DYNDCAWL20 C907U709DYNDCAWL35
C907U709DYNDCAWL40 C907U709DYNDCAWL45 C907U809DYNDAA7317 C907U809DYNDAAWL20
C907U809DYNDAAWL35 C907U809DYNDAAWL40 C907U809DYNDAAWL45 C907U809DYNDBA7317
C907U809DYNDBAWL20 C907U809DYNDBAWL35 C907U809DYNDBAWL40 C907U809DYNDBAWL45
工商网监
湘ICP备2023018690号
