AA3535SYL1Z1S

3.5x3.5 mm SMD CHIP LED LAMP Part Number: AA3535SYL1Z1S Super Bright Yellow ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Description The source color devices are made with AlGaInP Light Emitting Diode. Static electricity and surge damage the LEDS. It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs. All devices, equipment and machinery must be electrically grounded. Features White SMD package, silicone resin. Low thermal resistance. Compatible with IR-reflow processes. ESD protection. Package: 2000pcs / reel. Moisture sensitivity level : level 2a. RoHS compliant. Applications Signal and symbol luminaire for orientation. Marker lights (e.g. steps, exit ways, etc). Decorative and entertainment lighting. Commercial and residential lighting. Automotive interior lighting. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAJ4025 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: SEP/24/2010 DRAWN: Y.H.Wu PAGE: 1 OF 6 ERP: 1201004888 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or damage the internal circuitry. 4. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diameter of the nozzle should be as large as possible. 5. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 6. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. SPEC NO: DSAJ4025 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: SEP/24/2010 DRAWN: Y.H.Wu PAGE: 2 OF 6 ERP: 1201004888 S election Guide Part No. Dice Lens Type Iv (cd) [2] @ 150mA Min. AA3535SYL1Z1S Super Bright Yellow(AlGaInP) WATER CLEAR 2.8 Typ. 4 Φv (lm) [2] @ 150mA Min. 6 Typ. 8 Viewing Angle [1] 2 θ 1/2 120 ° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. Absolute Maximum Ratings at TA=25°C Parameter Power Dissipation Junction Temperature [1] Operating Temperature Storage Temperature DC Forward Current [1] Reverse Voltage Peak Forward Current [2] Thermal Resistance [1] (Junction/ambient) Thermal Resistance [1] (Junction/solder point) Electrostatic Discharge Threshold (HBM) Symbol PD TJ Top Tstg IF VR IFM Rth j-a Rth j-S Value 525 130 -40 To +85 -40 To +85 150 5 270 178 78 8000 Unit mW °C °C °C mA V mA °C/W °C/W V N otes: 1.Results from mounting on PC board FR4(pad size ≥ 70mm 2 ), mounted o n pc board-metal core PCB i s r ecommend f or lowest thermal Resistance. 2.1/10 Duty Cycle, 0.1ms Pulse Width. Electrical / Optical Characteristics at TA=25°C Parameter Wavelength at peak emission Dominant Wavelength IF=150mA [Typ.] Symbol λ peak λ dom [1] Δλ Value 590 590 20 2.5 VF [2] 3.0 3.5 IR TC λ peak TC λ dom TCV 10 0.13 0.10 -3.3 uA nm/ ° C nm/ ° C mV/ ° C V Unit nm nm nm IF=150mA [Typ.] Spectral Line Half-width IF=150mA [Typ.] Forward Voltage IF=150mA [Min.] Forward Voltage IF=150mA [Typ.] Forward Voltage IF=150mA [Max.] Reverse Current (VR = 5V) [Max.] Temperature coefficient of λ peak IF=150mA, -10 ° C≤ T≤100 ° C [Typ.] Temperature coefficient of λ dom IF=150mA, -10 ° C≤ T≤100 ° C [Typ.] Temperature coefficient of VF IF=150mA, -10 ° C≤ T≤100 ° C [Typ.] Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. SPEC NO: DSAJ4025 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: SEP/24/2010 DRAWN: Y.H.Wu PAGE: 3 OF 6 ERP: 1201004888 Super Bright Yellow AA3535SYL1Z1S SPEC NO: DSAJ4025 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: SEP/24/2010 DRAWN: Y.H.Wu PAGE: 4 OF 6 ERP: 1201004888 AA3535SYL1Z1S Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Reel Dimension Recommended Soldering Pattern (Units : mm; Tolerance: ±0.1) Tape Specifications (Units : mm) SPEC NO: DSAJ4025 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: SEP/24/2010 DRAWN: Y.H.Wu PAGE: 5 OF 6 ERP: 1201004888 PACKING & LABEL SPECIFICATIONS AA3535SYL1Z1S SPEC NO: DSAJ4025 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: SEP/24/2010 DRAWN: Y.H.Wu PAGE: 6 OF 6 ERP: 1201004888