PSG4NTEB1L00F

PSG4/PSF4 current sensing power shunt EU features current sense • Correcter electric current detection is possible with 4-terminal construction • Excellent T.C.R. achieved (±50×10-6/K) • Ultra low resistance, suitable for large current sensing • Automatic mounting machines are applicable • Suitable for reflow soldering (Not suitable for flow soldering) • Products meet EU RoHS requirements • AEC-Q200 tested dimensions and construction Type (Inch Size Code) PSG4 (2725) PSF4 (1216) Resist. (Ω) 0.5m 1m 0.5m 1m L W Dimensions inches (mm) c d Ws .272±.010 .260±.010 .079±.004 (6.9±0.25) (6.6±0.25) (2.0±0.1) .118±.004 .150±.004 (3.0±0.1) (3.8±0.1) –– –– Wv t .120±.008 .039±.004 .028±.010 (3.05±0.2) (1.0±0.1) (0.7±0.1) .110±.008 (2.8±0.2) .037±.006 .028±.002 .020±.002 .071±.004 (0.95±0.15) (0.7±0.05) (0.5±0.05) (1.8±0.1) L Derating Curve Current Terminal c Electrode 80 Ws Wv % Rated Power Resistive Element t 100 W d Voltage Terminal PSG4 PSF4 60 40 20 0 -80 -60 -40 -20 -65 When the terminal part temperature of the resistor exceeds the rated terminal part temperature shown, the power shall be derated according to the derating curve. Please refer to “Introduction of the derating curve based on the terminal part temperature” in the beginning of our catalog before use. 0 20 40 60 80 100 120 140 160 180 75 130 175 Terminal Part Temperature (°C) ordering information PS Type G 4 N Power Rating G (0.5m): 10W G (1m): 8W F (0.5m): 5W F (1m): 3W Termination Number Termination Material N: No surface treatment TEB Packaging TEB: Plastic embossed L500 Nominal Resistance 4 digits: all values less than 100mΩ are expressed in mΩ with “L” as decimal Ex: 0.5mΩ - L500 1mΩ - 1L00 F Tolerance F: ±1% Contact us when you have control request for environmental hazardous material other than the substance specified by EU RoHS. For further information on packaging, please refer to Appendix A. Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 4/13/20 KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com 95 PSG4/PSF4 current sensing power shunt applications and ratings Power Rating (Current Rating) current sense Part Designation T.C.R. (ppm/°C) Max. 10W (141A) PSG4 Resistance Tolerance Rated Terminal Part Temperature F: ±1% 75°C 0.5mΩ ±50 8W (89A) 1mΩ 5W (100A) PSF4 Resistance Range -65°C to +175°C 0.5mΩ ±50 3W (54A) Operating Temperature Range F: ±1% 130°C 1mΩ environmental applications One-Pulse Limiting Electric Power PSF4 1,000,000 100,000 10,000 1,000 0.5mΩ 100 1mΩ 10 1 .001 .01 10 1 .1 100 One-Pulse Limiting Electric Power (W) One-Pulse Limiting Electric Power (W) PSG4 10,000,000 10,000,000 1,000,000 100,000 10,000 1,000 100 0.5mΩ 1mΩ 10 1 .001 .01 Thermal Resistance PSF4 Rth (°C/W) 9 12 8 14 TH ＋ T＝Hs Terminal Part Temperature TH ：High TM ：Medium ＝ts TL ：Low TM ＋ T＝Hs Temperature PSG4 Resistance (Ω) 0.5m 1m 0.5m 1m 100 Pulse Duration (ms) Pulse Duration (ms) Type 10 1 .1 The maximum applicable voltage is equal to the max. overload voltage. Please ask us about the resistance characteristic of continuous applied pulse. The pulse endurance values are not assured values,so be sure to check the products on actual equipment when you use them. T TL ＋ T＝Hs Rth=(Hs-ts)/Power Regarding the temperature rise, the value of the temperature varies per conditions and board for use since the temperature is measured under our measuring conditions. Please refer to us before use. T T TH TM TL Low The temperature of the resistor will increase the same ⊿T from the standard terminal part temperature regardlless of the ambient temperature when the same power is applied. This is because there is hardly any heat dissipation from the resistor surface to the ambient air. High Terminal Part Temperature Performance Characteristics Parameter T.C.R. Requirement ∆ R ±% Limit Typical Within specified –– T.C.R. Overload (Short time) ±0.5% ±0.1% Resistance to Solder Heat Rapid Change of Temperature Moisture Resistance ±0.5% ±0.5% ±0.5% ±0.1% ±0.1% ±0.05% Endurance at Rated Terminal Part Temperature ±1.0% ±0.5% Low Temperature Exposure High Temperature Exposure ±0.5% ±1% ±0.01% ±0.6% Test Method +25°C/+125°C PSG4 (0.5mΩ): 30W for 5 seconds; PSG4 (1mΩ): 20W for 5 seconds PSF4 (0.5mΩ): 15W for 5 seconds; PSF4 (1mΩ): 9W for 5 seconds 260°C ± 5°C, 15 seconds ± 1 second -55°C (30 minutes), +150°C (30 minutes), 1,000 cycles 85°C ± 3°C, 85% ± 3% RH, 1000 hours, 10% Bias PSG4: Terminal part temperature: 75°C ± 3°C, 1000 hours, 1.5 hr ON, 0.5 hr OFF cycle PSF4: Terminal part temperature: 130°C ± 3°C, 1000 hours, 1.5 hr ON, 0.5 hr OFF cycle -65°C, 1000 hours +175°C, 1,000 hours Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 96 10/22/20 KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com