PSJ2NTEB2L00F

PSJ2/PSL2 current sensing power shunt EU features dimensions and construction Type (Inch Size Code) Resist. (Ω) L current sense • Ultra low resistance, suitable for large current sensing • Automatic mounting machines are applicable • Suitable for reflow soldering (Not suitable for flow soldering) • Products meet EU RoHS requirements • AEC-Q200 tested Dimensions inches (mm) W d L t W Electrode Resistive Element 0.2m 0.5m .05±.008 (1.27±0.2) 1m PSJ2 (3920) d 2m .035±.008 .394±.010 .205±.010 .079±.010 (0.89±0.2) (10.0±0.25) (5.2±0.25) (2.0±0.25) .046±.008 (1.17±0.2) 3m .037±.008 (0.95±0.2) 4m .033±.008 (0.84±0.2) 0.2m .055±.006 (1.40±0.15) 0.3m .248±.006 .124±.006 .045±.006 .052±.006 (6.3±0.15) (3.15±0.15) (1.15±0.15) (1.32±0.15) 0.5m .044±.006 (1.12±0.15) Derating Curve 100 PSL2 (2512) % Rated Power 80 60 t .078±.008 (1.98±0.2) 40 For resistors operated at a terminal part temperature of described for each size or above, a power rating shall be derated in accordance with the derating curve. Please refer to “Introduction of the derating curve based on the terminal part temperature” in the beginning of our catalog before use. 20 0 -80 -60 -40 -20 -65 0 20 40 60 80 100 120 140 160 180 75 175 Terminal Part Temperature (°C) ordering information PS Type J 2 N Power Rating J: 0.2m: 12W 0.5m: 10W 1m: 8W 2m: 6W 3m: 5W 4m: 5W L: 0.2m: 9W 0.3m: 8W 0.5m: 8W Termination Number Termination Material N: No surface treatment TEB Packaging TEB: 8mm pitch plastic embossed L500 Nominal Resistance 4 digits: all values less than 100mΩ are expressed in mΩ with “L” as decimal Ex: 0.5mΩ L500 1mΩ = 1L00 F Tolerance F: ±1% For further information on packaging, please refer to Appendix A. Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 10/22/20 KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com 93 PSJ2/PSL2 current sensing power shunt applications and ratings Power Rating (Current Rating) Part Designation current sense T.C.R. (ppm/°C) Max. Resistance Range 12W (244A) ±200 0.2mΩ 10W (141A) ±100 0.5mΩ 8W (89A) ±75 1mΩ 6W (54A) ±75 2mΩ 5W (41A) ±50 3mΩ 5W (35A) ±50 4mΩ NEW 9W (212A) 250±100 0.2mΩ 8W (163A) ±175 0.3mΩ 8W (126A) ±115 0.5mΩ PSJ2 PSL2 Resistance Tolerance Rated Terminal Part Temperature Operating Temperature Range F: ±1% 75°C -65°C to +175°C F: ±1% 75°C -65°C to +175°C environmental applications One-Pulse Limiting Electric Power PSL2 One-Pulse Limiting Electric Power (W) One-Pulse Limiting Electric Power (W) PSJ2 10,000,000 1,000,000 100,000 10,000 1,000 0.2mΩ 4mΩ 100 10 1 .001 .01 .1 1 10 100 10,000,000 1,000,000 100,000 10,000 1,000 100 0.2mΩ 10 0.5mΩ 1 .001 .01 .1 Pulse Duration (ms) PSL2 Rth (°C/W) 4 27 3.2 6.7 100 TH ＋ T＝Hs Terminal Part Temperature TH ：High TM ：Medium ＝ts TL ：Low TM ＋ T＝Hs Temperature PSJ2 Resistance (Ω) 0.2m 4m 0.2m 0.5m 10 Pulse Duration (ms) Thermal Resistance Type 1 The maximum applicable voltage is equal to the max. overload voltage. Please ask us about the resistance characteristic of continuous applied pulse. The pulse endurance values are not assured values,so be sure to check the products on actual equipment when you use them. T TL ＋ T＝Hs Rth=(Hs-ts)/Power Regarding the temperature rise, the value of the temperature varies per conditions and board for use since the temperature is measured under our measuring conditions. Please refer to us before use. T T TH TM TL Low The temperature of the resistor will increase the same ⊿T from the standard terminal part temperature regardlless of the ambient temperature when the same power is applied. This is because there is hardly any heat dissipation from the resistor surface to the ambient air. High Terminal Part Temperature Performance Characteristics Parameter T.C.R. Requirement ∆ R ±% Limit Typical Within specified –– T.C.R. Overload (Short time) ±0.5% ±0.1% Resistance to Solder Heat Rapid Change of Temperature Moisture Resistance Endurance at 75°C and Less of Terminal Part Temperature Low Temperature Exposure High Temperature Exposure ±0.5% ±0.5% ±0.5% ±0.1% ±0.1% ±0.05% ±1.0% ±0.3% ±0.5% ±1% ±0.02% ±0.5% Test Method +25°C/+125°C PSJ (0.2m): 36W for 5 seconds; PSJ (0.5m): 30W for 5 seconds; PSJ (1m): 20W for 5 seconds; PSJ (2m): 18W for 5 seconds; PSJ (3m): 12.5W for 5 seconds; PSJ (4m): 10W for 5 seconds; PSL (0.2m): 27W for 5 seconds; PSL (0.3m, 0.5m): 24W for 5 seconds 260°C ± 5°C, 15 seconds ± 1 second -55°C (30 minutes), +150°C (30 minutes), 1,000 cycles 85°C ± 3°C, 85% ± 3°C RH, 1000 hours, 10% Bias Terminal part temperature: 75°C ± 3°C, 1000 hours, 1.5 hr ON, 0.5 hr OFF cycle -65°C, 1000 hours +175°C, 1,000 hours Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 94 10/22/20 KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com