LF3320QC12

LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter DESCRIPTION The LF3320 filters digital images in the horizontal dimension at real-time video rates. The input and coefficient data are both 12 bits and in two’s complement format. The output is also in two’s complement format and may be rounded to 16 bits. The LF3320 is designed to take advantage of symmetric coefficient sets. When symmetric coefficient sets are used, the device can be configured as a single 32-tap FIR filter or as two separate 16-tap FIR filters. When asymmetric coefficient sets are used, the device can be configured as a single 16-tap FIR filter or as two separate 8-tap FIR filters. Multiple LF3320s can be cascaded to create larger filters. Interleave/Decimation Registers (I/D Registers) allow interleaved data to be fed directly into the device and filtered without separating the data into individual data streams. The LF3320 can handle a maximum of sixteen data sets interleaved together. The I/D Registers and on-chip accumulators facilitate using decimation to increase the number of filter taps. Decimation of up to 16:1 is supported. The LF3320 contains enough on-board memory to store 256 coefficient sets. Two separate LF InterfacesTM allow all 256 coefficient sets to be updated within vertical blanking. FEATURES ❑ 83 MHz Data Rate ❑ 12-bit Data or Coefficients (Expandable to 24-bit) ❑ 32-Tap FIR Filter, Cascadable for More Filter Taps ❑ Over 49 K-bits of on-board Memory ❑ LF InterfaceTM Allows All 256 Coefficient Sets to be Updated Within Vertical Blanking ❑ Various Operating Modes: Dual Filter, Single Filter, Double Wide Data or Coefficient, Matrix Multiplication, and Accumulator Access. ❑ Selectable 16-bit Data Output with User-Defined Rounding and Limiting ❑ Supports Interleaved Data Streams ❑ Supports Decimation up to 16:1 for Increasing Number of Filter Taps ❑ 3.3 Volt Supply ❑ 144 Lead PQFP LF3320 BLOCK DIAGRAM ROUT11-0 12 12 RIN11-0 DIN11-0 CAA7-0 CENA CFA11-0 PAUSEA LDA 12 INTERLEAVE / DECIMATION REGISTERS 12 COUT11-0 CAB7-0 8 8 CENB 12 256 COEFFICIENT SET STORAGE 16-TAP FILTER A 16-TAP FILTER B 256 COEFFICIENT SET STORAGE 12 CFB11-0 PAUSEB LDB ROUND SELECT LIMIT CIRCUITRY CLK OED 16 DOUT15-0 Video Imaging Products 2-1 08/16/2000–LDS.3320-N OEC 4 FILTER A I/D REGISTERS 12 RIN11-0 1-16 1-16 1-16 REOI DATA REVERSAL FIGURE 1. ROUT3-0 FILTER B I/D REGISTERS RSLB OUT15-12 8 1-16 1-16 1-16 1-16 1-16 1-16 1-16 1-16 1-16 1-16 SEOI DEVICES INCORPORATED DATA REVERSAL 1-16 ROUT11-4 12 1-16 1-16 1-16 1-16 1-16 1-16 1-16 1-16 1-16 1-16 1-16 1-16 1-16 1-16 OEC 12 COUT11-0 1-16 A A ALU ALU ALU ALU ALU ALU ALU ALU ALU ALU ALU ALU ALU ALU RSLB OUT11-0 CAA7-0 ALU 8 B B A A A A A A A A A A A A A B B B B B B B B B B B B B 1-16 DIN11-0 A ALU B CAB7-0 CENA 8 13 13 13 13 13 12 13 13 13 13 13 13 13 13 13 13 13 CENB Coef Bank 15 12 Coef Bank 0 12 12 Coef Bank 14 Coef Bank 1 12 12 Coef Bank 13 Coef Bank 2 12 12 Coef Bank 12 Coef Bank 3 12 12 Coef Bank 11 Coef Bank 4 12 12 Coef Bank 10 Coef Bank 5 12 12 Coef Bank 9 LF3320 FUNCTIONAL BLOCK DIAGRAM Coef Bank 6 12 12 Coef Bank 8 25 25 25 25 25 25 25 25 25 25 25 25 25 25 LDA CFA11-0 PAUSEA CFB11-0 ACCA 32 "0" 32 32 SCALE 32 "0" PAUSEB ACCM A ACCM B LDB 2-2 27 27 27 CONFIGURATION AND CONTROL REGISTERS ROUND SELECT LIMIT Coef Bank 7 25 25 FILTER A LF INTERFACE 27 FILTER B LF INTERFACE 12 12 ACCB TXFRA TXFRB ROUND SELECT LIMIT 4 4 RSLB3-0 FILTER A 16 FILTER B 16 RSLB OUT15-0 OED 16 DOUT15-0 RSLA3-0 SHENA SHENB Horizontal Digital Image Filter Video Imaging Products LF3320 08/16/2000–LDS.3320-N CLK LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter FIGURE 2. INPUT FORMATS Input Data 11 10 9 –211 210 29 (Sign) SIGNAL DEFINITIONS Power VCC and GND +3.3 V power supply. All pins must be connected. Clock CLK — Master Clock The rising edge of CLK strobes all enabled registers. Inputs DIN11-0 — Data Input DIN11-0 is the 12-bit data input port to Filter A. In Dual Filter Mode, DIN11-0 can also be the 12-bit input port to Filter B. Data is latched on the rising edge of CLK. RIN11-0 — Reverse Cascade Input In Single Filter Mode, RIN11-0 is the 12bit reverse cascade input port. This port is connected to ROUT11-0 of another LF3320. In Dual Filter Mode, RIN11-0 can be the 12-bit input port to Filter B. Data is latched on the rising edge of CLK. CFA11-0 — Coefficient A Input CFA11-0 is used to load data into the Filter A coefficient banks (banks 0 through 7) and the configuration/ control registers. Data present on CFA11-0 is latched into the Filter A LF InterfaceTM on the rising edge of CLK when LDA is LOW (see the LF InterfaceTM section for a full discussion). CAA7-0 — Coefficient Address A CAA7-0 determines which row of data in coefficient banks 0 through 7 is fed to the multipliers. CAA7-0 is latched into Coefficient Address Register A on the rising edge of CLK when CENA is LOW. Coefficient Data 11 10 9 –20 2–1 2–2 (Sign) 210 22 21 2 0 210 2–9 2–10 2–11 FIGURE 3. ACCUMULATOR OUTPUT FORMATS Accumulator A Output 31 30 29 –220 219 218 (Sign) Accumulator B Output 31 30 29 –220 219 218 (Sign) 210 2–9 2–10 2–11 210 2–9 2–10 2–11 TABLE 1. SLCT4-0 00000 00001 00010 OUTPUT FORMATS S15 S14 S13 F15 F16 F17 F14 F15 F16 F13 F14 F15 ··· ··· ··· ··· S8 F8 F9 F10 S7 F7 F8 F9 ··· ··· ··· ··· S2 F2 F3 F4 S1 F1 F2 F3 S0 F0 F1 F2 · · · 01110 01111 10000 · · · F29 F30 F31 · · · F28 F29 F30 · · · F27 F28 F29 · · · ··· ··· ··· F22 F23 F24 · · · F21 F22 F23 · · · ··· ··· ··· F16 F17 F18 · · · F15 F16 F17 · · · F14 F15 F16 CFB11-0 — Coefficient B Input CFB11-0 is used to load data into the Filter B coefficient banks (banks 8 through 15) and the configuration/ control registers. Data present on CFB11-0 is latched into the Filter B LF InterfaceTM on the rising edge of CLK when LDB is LOW (see the LF InterfaceTM section for a full discussion). CAB7-0 — Coefficient Address B CAB7-0 determines which row of data in coefficient banks 8 through 15 is fed to the multipliers. CAB7-0 is latched into Coefficient Address Register B on the rising edge of CLK when CENB is LOW. Outputs DOUT15-0 — Data Output DOUT15-0 is the 16-bit registered data output port for the overall filter (Single Filter Mode) or Filter A (Dual Filter Mode). COUT11-0 — Cascade Output In Single Filter Mode, COUT11-0 is a 12-bit registered cascade output port. COUT11-0 should be connected to DIN11-0 of another LF3320. In Dual Filter Mode, COUT11-0 is a 12-bit registered output port for the lower twelve bits of the 16-bit Filter B output. Video Imaging Products 2-3 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter CENB — Coefficient Address Enable B When CENB is LOW, data on CAB7-0 is latched into Coefficient Address Register B on the rising edge of CLK. When CENB is HIGH, data on CAB7-0 is not latched and the register’s contents will not be changed. TXFRA — Filter A LIFO Transfer Control TXFRA is used to change which LIFO in the data reversal circuitry sends data to the reverse data path and which LIFO receives data from the forward data path in Filter A. When TXFRA goes LOW, the LIFO sending data to the reverse data path becomes the LIFO receiving data from the forward data path, and the LIFO receiving data from the forward data path becomes the LIFO sending data to the reverse data path. The device must see a HIGH to LOW transition of TXFRA in order to switch LIFOs. TXFRA is latched on the rising edge of CLK. TXFRB — Filter B LIFO Transfer Control TXFRB is used to change which LIFO in the data reversal circuitry sends data to the reverse data path and which LIFO receives data from the forward data path in Filter B. When TXFRB goes LOW, the LIFO sending data to the reverse data path becomes the LIFO receiving data from the forward data path, and the LIFO receiving data from the forward data path becomes the LIFO sending data to the reverse data path. The device must see a HIGH to LOW transition of TXFRB in order to switch LIFOs. TXFRB is latched on the rising edge of CLK. ACCA — Accumulator A Control When ACCA is HIGH, Accumulator A is enabled for accumulation and the Accumulator A Output Register is disabled for loading. When ACCA is LOW, no accumulation is performed and the Accumulator A Output Register is enabled for loading. ACCA is latched on the rising edge of CLK. ACCB — Accumulator B Control When ACCB is HIGH, Accumulator B is enabled for accumulation and the Accumulator B Output Register is disabled for loading. When ACCB is LOW, no accumulation is performed and the Accumulator B Output Register is enabled for loading. ACCB is latched on the rising edge of CLK. SHENA — Filter A Shift Enable In Dual Filter Mode, SHENA enables or disables the loading of data into the Input (DIN11-0) and Filter A I/D Registers. When SHENA is LOW, data is latched into the Input/Cascade Registers and shifted through the I/D Registers on the rising edge of CLK. When SHENA is HIGH, data can not be loaded into the Input/Cascade Registers or shifted through the I/D Registers and their contents will not be changed. In Single Filter Mode, SHENA also enables or disables the loading of data into the Reverse Cascade Input (RIN110), Cascade Output (COUT11-0), Reverse Cascade Output (ROUT11-0) and Filter B I/D Registers. It is important to note that in Single Filter Mode, both SHENA and SHENB should be connected together. Both must be active to enable data loading in Single Filter Mode. SHENA is latched on the rising edge of CLK. SHENB — Filter B Shift Enable In Dual Filter Mode, SHENB enables or disables the loading of data into the Reverse Cascade Input (RIN11-0), Cascade Output (COUT11-0), Reverse Cascade Output (ROUT3-0) and Filter B I/D Registers. When SHENB is LOW, data is latched into the Cascade Registers and shifted through the I/D ROUT11-0 — Reverse Cascade Output In Single Filter Mode, ROUT11-0 is a 12-bit registered cascade output port. ROUT11-0 on one device should be connected to RIN11-0 of another LF3320. In Dual Filter Mode, ROUT3-0 is a 4-bit registered output port for the upper four bits of the 16-bit Filter B output. In this mode, ROUT11-4 is disabled. Controls LDA — Coefficient A Load When LDA is LOW, data on CFA11-0 is latched into the Filter A LF InterfaceTM on the rising edge of CLK. When LDA is HIGH, data is not loaded into the Filter A LF InterfaceTM. When enabling the LF InterfaceTM for data input, a HIGH to LOW transition of LDA is required in order for the input circuitry to function properly. Therefore, LDA must be set HIGH immediately after power up to ensure proper operation of the input circuitry (see the LF InterfaceTM section for a full discussion). CENA — Coefficient Address Enable A When CENA is LOW, data on CAA7-0 is latched into Coefficient Address Register A on the rising edge of CLK. When CENA is HIGH, data on CAA7-0 is not latched and the register’s contents will not be changed. LDB — Coefficient B Load When LDB is LOW, data on CFB11-0 is latched into the Filter B LF InterfaceTM on the rising edge of CLK. When LDB is HIGH, data is not loaded into the Filter B LF InterfaceTM. When enabling the LF InterfaceTM for data input, a HIGH to LOW transition of LDB is required in order for the input circuitry to function properly. Therefore, LDB must be set HIGH immediately after power up to ensure proper operation of the input circuitry (see the LF InterfaceTM section for a full discussion). Video Imaging Products 2-4 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter ROUT3-0 are enabled for output. When OEC is HIGH, COUT11-0 and ROUT3-0 are placed in a high-impedance state. PAUSEA — LF InterfaceTM Pause When PAUSEA is HIGH, the Filter A LF InterfaceTM loading sequence is halted until PAUSEA is returned to a LOW state. This effectively allows the user to load coefficients and control registers at a slower rate than the master clock (see the LF InterfaceTM section for a full discussion). PAUSEB — LF InterfaceTM Pause When PAUSEB is HIGH, the Filter B LF InterfaceTM loading sequence is halted until PAUSEB is returned to a LOW state. This effectively allows the user to load coefficients and control registers at a slower rate than the master clock (see the LF InterfaceTM section for a full discussion). Registers on the rising edge of CLK. When SHENB is HIGH, data can not be loaded into the Cascade Registers or shifted through the I/D Registers and their contents will not be changed. In Single Filter Mode, SHENB also enables or disables the loading of data into the Input (DIN11-0), Reverse Cascade Output (ROUT11-0) and Filter A I/D Registers. It is important to note that in Single Filter Mode, both SHENA and SHENB should be connected together. Both must be active to enable data loading in Single Filter Mode. SHENB is latched on the rising edge of CLK. RSLA3-0 — Filter A Round/Select/Limit Control RSLA3-0 determines which of the sixteen user-programmable Round/ Select/Limit registers (RSL registers) are used in the Filter A RSL circuitry. A value of 0 on RSLA3-0 selects RSL register 0. A value of 1 selects RSL register 1 and so on. RSLA3-0 is latched on the rising edge of CLK (see the round, select, and limit sections for a complete discussion). RSLB3-0 — Filter B Round/Select/Limit Control RSLB3-0 determines which of the sixteen user-programmable RSL registers are used in the Filter B RSL circuitry. A value of 0 on RSLB3-0 selects RSL register 0. A value of 1 selects RSL register 1 and so on. RSLB3-0 is latched on the rising edge of CLK (see the round, select, and limit sections for a complete discussion). OED — DOUT Output Enable When OED is LOW, DOUT15-0 is enabled for output. When OED is HIGH, DOUT15-0 is placed in a highimpedance state. OEC — COUT/ROUT Output Enable When OEC is LOW, COUT11-0 and FIGURE 4. SINGLE FILTER MODE 12 ROUT11-0 12 DIN11-0 I/D REGISTERS I/D REGISTERS 12 RIN11-0 12 COUT11-0 FILTER A FILTER B RSL CIRCUIT 16 DOUT15-0 FIGURE 5. DUAL FILTER MODE 12 12 DIN11-0 I/D REGISTERS I/D REGISTERS RIN11-0 FILTER A FILTER B R.S.L. CIRCUIT 16 DOUT15-0 R.S.L. CIRCUIT 16 ROUT3-0 / COUT11-0 Video Imaging Products 2-5 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter RIN11-0 or DIN11-0 can be the data input for Filter B. The Filter B input is determined by Bit 2 in Configuration Register 5. DOUT15-0 is the data output for Filter A. COUT11-0 and ROUT3-0 together form the data output for Filter B. COUT11-0 is the twelve least significant bits and ROUT3-0 is the four most significant bits of the 16-bit Filter B output. Matrix-vector Multiply Mode In this mode, the LF3320 can be configured to multiply a square matrix of maximum size N (N = 8 or 16), multiplied by a matrix-vector of maximum size [8,1] or [16,1]. The mathematical representation for this operation is in Figure 7. When configured in the dual filter mode, the LF3320 can process two matrix-vector multipliers simultaneously (i.e. [8x8][8x1]). In the single filter mode, the LF3320 can process a single matrix-vector multiply (i.e. [16x16][16x1]). This mode of operation allows the user to organize data values (e.g. pixels) into an array (e.g. blocks). This function is useful for any application requiring the operation of matrix multiplication; a function that is used when generating Discrete Cosine Transform coefficients (DCT) for the purpose of further processing. When configuring the LF3320 for an [8x8][8x1] matrix-vector operation, the coefficient banks will require 8 coefficient sets to be loaded into the coefficient memory banks; each coefficient set will have 8, 12-bit coefficients. The input data, [8x1] column-vector, will be loaded through DIN11-0 for Filter A; either RIN11-0 or DIN11-0 can be the data input for Filter B. Conversely, when configured for a [16x16][16x1] matrix-vector operation, the coefficient banks will require 16 coefficient sets to be loaded into the coefficient memory banks; each coefficient set will have 16, 12-bit coefficients. The input data, [16x1] column-vector, will be loaded through DIN11-0. To configure the LF3320 for matrix-vector multiplication, bit 4 of Configuration Register 5 must be set to 1 (Table 7). The configuration for single filter mode or dual filter mode will still apply. Writing 012H or 016H to Configuration Register 5 will configure the device for dual filter mode, [8x8][8x1] matrix-vector multiplication. Subsequently, writing 014H to Configuration Register 5 will configure the device for single filter OPERATIONAL MODES Single Filter Mode In this mode, the device operates as a single FIR filter (see Figure 4). It can be configured to have as many as 32 taps if symmetric coefficient sets are used. If asymmetric coefficient sets are used, the device can be configured to have as many as 16 taps. Cascade ports are provided to facilitate cascading multiple devices to increase the number of filter taps. Bit 1 in Configuration Register 5 determines the filter mode. In Single Filter Mode, DIN11-0 is the data input for the filter and DOUT15-0 is the data output for the filter. Dual Filter Mode In this mode, the device operates as two separate FIR filters (see Figure 5). Each filter can be configured to have as many as 16 taps if symmetric coefficient sets are used. If asymmetric coefficient sets are used, each filter can be configured to have as many as 8 taps. In Dual Filter Mode, DIN11-0 is the data input for Filter A. Either FIGURE 6. MATRIX-VECTOR MULTIPLY MODE N DIN11-0 RIN11-0 12 0 A B A 0 B A 0 B A 0 B ALU ALU ALU ALU FIGURE 7. MATRIX EQUATION C = COEFFICIENTS D = DATA INPUT R = DATA OUTPUT TXFRA TXFRB 12 COEF (N-1) N COEF 2 12 12 COEF 1 12 COEF 0 C00 C01 C02 R0 C10 C11 C12 R1 R2 = C20 C21 C22 Ri Ci0 Ci1 Ci2 (N-1) C0j C1j C2j Cij D0 D1 D2 Di Ri Dual Filter Mode, N=8 Single FIlter Mode, N=16 32 = Cij Di i=0 For j=0,1,2,...,(N-1) N=8 or 16 Video Imaging Products 2-6 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter to be configured for A+B (Table 2 and Table 4); so that condition A+0 is satisfied. To accomplish this, bit 0 is to be reset to 0, bit 1 is to be set to 1, and bit 2 is to be reset to 0. Writing 002H to Configuration Register 0 (Filter A) and Configuration Register 2 (Filter B) will set the corresponding registers to satisfy the A+0 condition. The timing diagrams in Figure 8 and 9 will assume that the Configuration Registers, the coefficient sets, and the first set of data values (data set) have been loaded. Loading input data for an [8x8][8x1] matrix operation requires 9 clock cycles and loading input data for a [16x16][16x1] matrix operation requires 17 clock cycles. When configured for an [8x8][8x1] matrix-vector operation, 8 data values are required for loading. When configured for a [16x16][16x1] matrix-vector operation, 16 data values are required for loading. Each data value is fed through the I/D Registers, using the corresponding input. Once the final data value, of the data set, has been loaded TXFRA/TXFRB should be brought LOW for one clock cycle to complete the loading. Once this occurs, the data set is then bank loaded into the respective registers ready to begin the matrix-vector multiplication operation. The current data set will not change until TXFRA/TXFRB is brought LOW again. To satisfy the matrix equation (see Figure 7), the current data set is held for the duration of the required matrix dimension while cycling through each coefficient set (CENA/CENB must be held LOW). During this time new data values can be loaded serially, ready for the next activation of TXFRA/TXFRB. To insure the correct evaluation of the matrix-vector multiplication equation, it is imperative that the coefficient values are paired with their corresponding data values. For the [8x8][8x1] matrix-vector configuration (dual filter mode), the first result will appear 19 clock cycles from the first data input, DIN15-0 (Filter A) and RIN15-0 (Filter B); device latency for the first result is 10 clock cycles (10+9 = 19). The result will appear at the corresponding filter output, DOUT15-0 (Filter A) and ROUT3-0/COUT11-0 (Filter B). For the [16x16][16x1] matrix-vector configuration (single filter mode), the first result will appear mode, [16x16][16x1] matrix-vector multiplication. Some functions of the LF3320 must be disabled when configured for matrix-vector multiplication. This will apply to both the single filter mode and the dual filter mode; these functions are data reversal and interleave/decimation. The LF3320 can be cascaded to realize larger matrices. Data reversal can be disabled by setting bit 6, of Configuration Register 1 (Filter A) and Configuration Register 3 (Filter B), both to 1. The Odd-Tap, interleave mode will need to be disabled. Writing a 0 to bit 0 of Configuration Register 1 and Configuration Register 3 will disable the odd-tap interleave mode for Filter A and Filter B. When data is not being interleaved or decimated, the I/D Register length should be set to a length of one (Table 3 and Table 5). Therefore, writing 040H to Configuration Register 1 and 3 will disable the data reversal and set the corresponding inherent characteristics for the desired matrix function. The Filter A ALU and Filter B ALU are FIGURE 8. DUAL FILTER, MATRIX MULTIPLY TIMING SEQUENCE Data Set 1 with 8 Coefficient Sets 1 CLK DIN11-0 RIN11-0 CAA7-0 CAB7-0 TXFRA/ TXFRB DOUT15-0 ROUT3-0/COUT15-0 CENA / CENB SHENA / SHENB * ** *** 8 Clocks - End of First Data/Coefficient Set 10 Clocks - First Output of First Data/Coefficient Set 17 Clocks - Final Output of First Data/Coefficient Set OUT0 OUT1 OUT7 OUT0 OUT1 Data Set 2 with 8 Coefficient Sets 9 10** 11 17*** 18 2 3 8* DATA SET 0 DATA SET 1 CF00 CF01 CF02 CF07 CF10 CF11 CF12 CF17 CF20 CF21 Video Imaging Products 2-7 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter FIGURE 9. SINGLE FILTER, MATRIX MULTIPLY TIMING SEQUENCE 1 Data Set with 16 Coefficient Sets 1 CLK DIN11-0 RIN11-0 CAA7-0 CAB7-0 TXFRA/ TXFRB DOUT15-0 CENA / CENB SHENA / SHENB * ** *** 11 Clocks - First Output of First Data/Coefficient Set 16 Clocks - End of First Data/Coefficient Set 26 Clocks - Final Output of First Data/Coefficient Set OUT0 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT15 2 3 11* 12 13 14 15 16** 17 26*** DATA SET 0 DATA SET 0 CF00 CF01 CF02 CF0A CF0B CF0C CF0D CF0E CF0F CF10 28 clock cycles from the first data input, DIN15-0; device latency for the first result is 11 clock cycles (11+17 = 28). The result will appear at the corresponding filter output, DOUT15-0. Subsequently, for both dual and single filter mode configurations, the sum of products will continue to appear every clock cycle thereafter until the matrix dimension has been realized. The total pipeline latency for a complete [8x8][8x1] matrix-vector operation is 26 clock cycles and the total pipeline latency for a complete [16x16][16x1] matrix-vector operation is 43 clock cycles. Therefore, to process two square matrices simultaneoulsy, of size N=8, a total of 73 clock cycles are all that is required. Similarly, to process a single square matrix, of size N=16, a total of 283 clock cycles are required. Once again, the timing diagrams (see Figure 8 and 9) will assume that the Configuration Registers, the coefficient sets, and the data values have been loaded. The corresponding timing diagram loading sequence for the coefficient banks and Configuration/Control registers are included in the LF3320 data sheets FIGURE 10. DOUBLE WIDE DATA/COEFFICIENT MODE 12 DIN11-0 12 RIN11-0 I/D REGISTERS I/D REGISTERS FILTER A FILTER B SCALE R.S.L. CIRCUIT 16 DOUT15-0 (Figure 11 and Figure 12 respectively). Further reference to timing diagram loading sequence for the RSL registers are also included in the device data sheet (Figure 15, Figure 14, and Figure 13). The Filter A and Filter B LF InterfaceTM are used to load data into the Filter A and Filter B Configuration Registers and coefficient banks. The Matrix Multiplication Mode is valid in the Double Wide Data/Coefficient Mode. However, there are some special considerations when this mode is desired. The LF3320 must be configured for single filter mode only, for a maximum (8x8) matrix. The user must disable the cascaded filter mode, the accumulator access mode, and the data reversal (see Table 7). Double Wide Data/Coefficient Mode Video Imaging Products 2-8 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter FIGURE 11. ACCUMULATOR ACCESS MODE 12 DIN11-0 I/D REGISTERS I/D REGISTERS 12 RIN11-0 The LF3320 is capable of supporting 24-bit data and 12-bit coefficients or 12-bit data and 24-bit coefficients. When configured for this mode of operation, the Filter B output is scaled by 2-12 before adding it to the Filter A output. This mode of operation is only valid in single filter mode. To configure the LF3320 for this mode, bit 3 of Configuration Register 5 must be set to 1; this will account for the scaling function (Table 7). For 24-bit data, DIN11-0 becomes the MSB (Filter A) and RIN11-0 becomes the LSB (Filter B), bit 2 of Configuration Register 5 must be set to 0. To insure correct results, the coefficient sets must be aligned appropriately; that is to say, the coefficient set used for the MSB must be the same for the LSB. For 24-bit coefficients, the coefficient banks for Filter A will correspond to the coefficient MSB and the coefficient banks for Filter B will correspond to the coefficient LSB; therefore, bit 2 must be set to 1. Once again, to insure correct results, the coefficient sets must be aligned appropriately; that is to say, the MSB coefficients must correspond to their LSB coefficients. The output data will appear at DOUT15-0; output appearing at ROUT3-0/COUT11-0 will not be of any value. Bit 1 is set to 0 (for single filter mode) and bit 0 is set to 0 (cascade mode must be disabled). Therefore, to realize 24-bit data/12-bit coefficients the user must write 008H to Configuration Register 5; conversely, for 12-bit data/24-bit coefficients the user must write 00CH to Configuration Register 5. The Double Wide Data/Coefficient Mode is valid in the Matrix Multiplication Mode; however, special considerations must be observed when these two modes are combined. The LF3320 must be configured for single filter mode only, for a maximum (8x8) matrix. In addition, the user must disable the cascaded filter mode, the accumulator access mode, and the data FILTER A FILTER B R.S.L. CIRCUIT 16 DOUT15-0 R.S.L. CIRCUIT 16 ROUT3-0 / COUT11-0 reversal (Table 7). For additional considerations, refer to the corresponding mode of operation section. Accumulator Access Mode Accumulator access allows the user to accumulate the Filter A output with the Filter B output. Therefore, this mode is only valid when the device has been configured for dual filter operation. To configure the device for this mode, bit 1 and bit 5 must be set to 1; bit 5 is the corresponding accumulator access bit (Table 7). Writing 022H to Configuration Register 5 configures the device to accumulate the Filter A output with the Filter B output. All remaining Configuration Registers, 0 through 4 inclusive, will depend on specific application requirements (see Tables 2 through 4). In this mode of operation, the accumulated output is realized at DOUT15-0. The output data at ROUT15-0/COUT15-0 is the Filter B output that is normally expected; however, the accumulated output data (DOUT15-0) will be delayed by one clock cycle, compared to the Filter B output data. This type of operation is useful when two filtered data streams (i.e. I+jQ) need to be accumulated. Such is the requirement to satisfy the equation, y(t) = cos(vt)+jsin(vt). The complex data can be streamed and filtered using a respective ‘I’ filter and ‘Q’ filter. To convert the complex result into a real result, as seen at the LF3320 output, two multiplies and one accumulation is required. The cosine and sine functions are realized through the coefficient sets; consequently, multiplied by the corresponding ‘I’ and ‘Q’ data streams. To satisfy the remainder of the equation, Filter A and Filter B must be accumulated. As previously stated, this mode of operation is only valid with the dual filter mode configuration. All modes of operation, that are valid in the dual filter mode, are valid with the accumulator access mode. For additional considerations, refer to the corresponding mode of operation section. FUNCTIONAL DESCRIPTION ALUs The ALUs double the number of filter taps available, when symmetric coefficient sets are used, by pre-adding data values which are then multiplied by a common coefficient (see Figure 12). Video Imaging Products 2-9 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter FIGURE 12. SYMMETRIC COEFFICIENT SET EXAMPLES 8765 87654321 7654321 4321 Even-Tap, Even-Symmetric Coefficient Set Odd-Tap, Even-Symmetric Coefficient Set Even-Tap, Odd-Symmetric Coefficient Set FIGURE 13. 1-16 1-16 A ALU B I/D REGISTER DATA PATHS DATA REVERSAL DATA REVERSAL DATA REVERSAL 1-16 1-16 1-16 1-16 1-16 1-16 A ALU B 1-16 1-16 1-16 Delay Stage N–1 Delay Stage N A ALU B A ALU B A ALU B 1-16 A ALU B COEF 7 COEF 6 COEF 7 2 COEF 6 COEF 7 2 COEF 6 EVEN-TAP MODE ODD-TAP MODE ODD-TAP INTERLEAVE MODE The ALUs can perform two operations: A+B and B–A. Bit 0 of Configuration Register 0 determines the operation of the ALUs in Filter A. Bit 0 of Configuration Register 2 determines the operation of the ALUs in Filter B. A+B is used with evensymmetric coefficient sets. B–A is used with odd-symmetric coefficient sets. Also, either the A or B operand may be set to 0. Bits 1 and 2 of Configuration Register 0 and Configuration Register 2 control the ALU inputs in Filters A and B respectively. A+0 or B+0 are used with asymmetric coefficient sets. Interleave/Decimation Registers The Interleave/Decimation Registers (I/D Registers) feed the ALU inputs. They allow the device to filter up to sixteen data sets interleaved into the same data stream without having to separate the data sets. The I/D Registers should be set to a length equal to the number of data sets interleavedtogether. For example, if two data sets are interleaved together, the I/D Registers should be set to a length of two. Bits 1 through 4 of Configuration Register 1 and Configuration Register 3 determine the length of the I/D Registers in Filters A and B respectively. The I/D Registers also facilitate using decimation to increase the number of filter taps. Decimation by N is accomplished by reading the filter’s output once every N clock cycles. The device supports decimation up to 16:1. With no decimation, the maximum number of filter taps is sixteen. When decimating by N, the number of filter taps becomes 16N because there are N–1 clock cycles when the filter’s output is not being read. The extra clock cycles are used to calculate more filter taps. When decimating, the I/D Registers should be set to a length equal to the decimation factor. For example, when performing a 4:1 decimation, the I/D Registers should be set to a length of four. When decimation is disabled or when only one data set (non-interleaved data) is fed into the device, the I/D Registers should be set to a length of one. Video Imaging Products 2-10 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter reverse data path. Bit 5 in Configuration Register 1 and Configuration Register 3 configures Filters A and B respectively for an even or odd number of taps. When interleaved data is fed through the device and an even tap filter is desired, the filter should be configured for an even number of taps and the I/D Register length should match the number of data sets interleaved together. When interleaved data is fed through the device and an odd tap filter is desired, the filter should be set to Odd-Tap Interleave Mode. Bit 0 of Configuration Register 1 and Configuration Register 3 configures Filters A and B respectively for Odd-Tap Interleave Mode. When the filter is configured for Odd-Tap Interleave Mode, data from the next to last I/D Register in the forward data path is fed into the first I/D Register in the reverse data path. When the filter is configured for an odd number of taps (interleaved or non-interleaved modes), the filter is structured such that the center data value is aligned simultaneously at the A and B inputs of the last ALU in the forward data path. In order to achieve the correct result, the user must divide the coefficient by two. Data Reversal Data reversal circuitry is placed after the multiplexers which route data from the forward data path to the reverse data path (see Figure 14). When decimating, the data stream must be reversed in order for data to be properly aligned at the inputs of the ALUs. When data reversal is enabled, the circuitry uses a pair of LIFOs to reverse the order of the data sent to the reverse data path. TXFRA and TXFRB control the LIFOs in Filters A and B respectively. When TXFRA/TXFRB goes LOW, the LIFO sending data to the reverse data path becomes the LIFO receiving data from the forward data path, and the LIFO receiving data from the forward data path becomes the LIFO sending data to TABLE 2. BITS 0 1 2 11-3 CONFIGURATION REGISTER 0 – ADDRESS 200H FUNCTION ALU Mode Filter A Pass A Filter A Pass B Filter A Reserved DESCRIPTION 0: A + B 1: B – A 0 : ALU Input A = 0 1 : ALU Input A = Forward Register Path 0 : ALU Input B = 0 1 : ALU Input B = Reverse Register Path Should be set to “0” TABLE 3. BITS 0 4-1 CONFIGURATION REGISTER 1 – ADDRESS 201H FUNCTION Filter A Odd-Tap Interleave Mode Filter A I/D Register Length DESCRIPTION 0 : Odd-Tap Interleave Mode Disabled 1 : Odd-Tap Interleave Mode Enabled 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 : : : : : : : : : : : : : : : : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Register Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers 5 6 11-7 Filter A Tap Number Filter A Data Reversal Reserved 0 : Even Number of Taps 1 : Odd Number of Taps 0 : Data Reversal Enabled 1 : Data Reversal Disabled Should be set to “0” I/D Register Data Path Control The three multiplexers in the I/D Register data path control how data is routed through the forward and reverse data paths. The forward data path contains the I/D Registers in which data flows from left to right in the block diagram in Figure 1. The reverse data path contains the I/D Registers in which data flows from right to left. In Single or Dual Filter Modes, data is fed from the forward data path to the reverse data path as follows. When the filter is configured for an even number of taps, data from the last I/D Register in the forward data path is fed into the first I/D Register in the reverse data path (see Figure 13). When the filter is configured for an odd number of taps, the data which will appear at the output of the last I/D Register in the forward data path on the next clock cycle is fed into the first I/D Register in the Video Imaging Products 2-11 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter Configuration Register 3 enables or disables data reversal for Filters A and B respectively. Cascading Three cascade ports are provided to allow cascading of multiple devices for more filter taps (see Figure 15). COUT11-0 of one device should be connected to DIN11-0 of another device. ROUT11-0 of one device should be connected to RIN11-0 of another device. As many LF3320s as desired may be cascaded together. However, the outputs of the LF3320s must be added together with external adders. Bit 0 of Configuration Register 5 determines how the device will send data to the reverse data path when multiple LF3320s are cascaded together. If a LF3320 is the last in the cascade chain, Bit 0 of Configuration Register 5 should be set to a “0”. This will cause the data from the end of the forward data path to be routed to the beginning of the reverse data path based on how the filter is configured (even/odd number of taps or interleave mode). If a LF3320 is not the last in the cascade chain, Bit 0 of Configuration Register 5 should be set to a “1”. This will cause RIN11-0 to feed data to the reverse data path. When not cascading, Bit 0 of Configuration Register 5 should be set to a “0”. Special data routing circuitry is used to feed the COUT and ROUT output registers. The data routing circuitry is required to correctly align data in the forward and reverse data paths as data passes from one LF3320 to another. The COUT and ROUT registers are loaded with data which is two clock cycles behind the current output of the I/D Register just before the ROUT or COUT register. This correctly accounts for the extra delays added to the forward and reverse data paths by the input/output cascade registers. the reverse data path. The device must see a HIGH to LOW transition of TXFRA/TXFR B in order to switch LIFOs. If decimating by N, TXFRA/TXFRB should go LOW once every N clock cycles. When data reversal is disabled, the circuitry functions like an I/D Register. When feeding interleaved data through the filter, data reversal should be disabled. Bit 6 of Configuration Register 1 and FIGURE 14. DATA REVERSAL TXFRA/TXFRB LIFO A LIFO B FIGURE 15. MULTIPLE LF3320S CASCADED TOGETHER LF3320 RIN DIN 12 I/D REGISTERS I/D REGISTERS COUT ROUT DIN I/D REGISTERS I/D REGISTERS FILTER A 1-16 FILTER B RSL CIRCUIT 16 LF3320 RIN COUT ROUT DIN LF3320 RIN I/D REGISTERS I/D REGISTERS COUT ROUT DIN LF3320 I/D REGISTERS I/D REGISTERS FILTER A FILTER B FILTER A FILTER B FILTER A FILTER B RSL CIRCUIT RSL CIRCUIT RSL CIRCUIT 16 16 16 LF3347 25 25 RSL CIRCUIT 16 DATA OUT 128 TAP RESULT Video Imaging Products 2-12 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter the contents of one of the sixteen Filter A or B round registers to the overall filter, Filter A, or Filter B outputs (see Figure 10). The Filter A round registers are used for the overall filter (Single Filter Mode) or Filter A (Dual Filter Mode). The Filter B round registers are used for Filter B (Dual Filter Mode). Each round register is 32-bits wide and user-programmable. This allows the filter’s output to be rounded to any precision required. Since any 32-bit value may be programmed into the round registers, the device can support complex rounding algorithms as well as standard Half-LSB rounding. RSLA3-0 determines which of the sixteen Filter A round registers are used in the Filter A rounding circuitry. RSLB3-0 determines which of the sixteen Filter B round registers are used in the Filter B rounding circuitry. A value of 0 on RSLA/RSLB3-0 selects Filter A/B round register 0. A value of 1 selects Filter A/B round register 1 and so on. RSLA/RSLB3-0 may be changed every clock cycle if desired. This allows the rounding algorithm to be changed every clock cycle. This is useful when filtering interleaved data. If rounding is not desired, a round register should be loaded with 0 and selected as the register used for rounding. Round register loading is discussed in the LF InterfaceTM section. Output Select The word width of the overall filter, Filter A, and Filter B outputs is 32-bits. However, only 16-bits may be sent to DOUT15-0 (Single or Dual Filter Modes) and COUT11-0/ROUT3-0 (Dual Filter Mode). The Filter A/B select circuitry determines which 16-bits are passed (see Table 1). The Filter A/B select registers control the Filter A/B select circuitry. There are sixteen Filter A and B select registers. The Filter A select registers are used for the overall filter (Single Filter Mode) or Filter A (Dual Filter Mode). The Filter B select registers are used for Filter B (Dual Filter Mode). Each select register is 5 bits wide and user-programmable. RSLA3-0 determines which of the sixteen Filter A select registers are used in the Filter A select circuitry. RSLB3-0 determines which of the sixteen Filter B select registers are used in the Filter B select circuitry. A value of 0 on RSLA/RSLB3-0 selects Filter A/B select register 0. A value of 1 selects Filter A/B select register 1 and so on. RSLA/RSLB3-0 may be changed every clock cycle if desired. This allows the 16-bit window to be changed every clock cycle. This is useful when filtering interleaved data. Select register loading is discussed in the LF InterfaceTM section. Output Adder The Output Adder adds the Filter A and B outputs together when the device is in Single Filter Mode. If 24-bit data and 12bit coefficients or 12-bit data and 24-bit coefficients are desired, the LF3320 can facilitate this by scaling the Filter B output by 2-12 before adding it to the Filter A output. Bit 3 in Configuration Register 5 determines if the Filter B output is scaled before being added to the Filter A output. Rounding The overall filter output (Single Filter Mode) or Filter A and B outputs (Dual Filter Mode) may be rounded by adding FIGURE 16. FILTER A AND B ROUND/SELECT/LIMIT CIRCUITRY RSLB3-0 4 DATA IN 32 DATA IN 32 RSLA3-0 4 RB0 32 RND RND 32 RB15 32 32 SB0 5 SELECT SELECT 5 SB15 16 16 LB0 32 LIMIT LIMIT 32 LB15 FILTER B RSL 16 DATA OUT 16 DATA OUT FILTER A RSL LA15 LA0 SA15 SA0 RA15 RA0 Video Imaging Products 2-13 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter register contains an upper and lower limit value. If the value fed to the limiting circuitry is less than the lower limit, the lower limit value is passed as the filter output. If the value fed to the limiting circuitry is greater than the upper limit, the upper limit value is passed as the filter output. Bit 1 and 0 in Configuration Register 4 enable and disable Filter A and B limiting respectively. RSLA/RSLB3-0 may be changed every clock cycle if desired. This allows the limit range to be changed every clock cycle. This is useful when filtering interleaved data. When loading limit values into the device, the upper limit must be greater than the lower limit. Limit register loading is discussed in the LF InterfaceTM section. Coefficient Banks The coefficient banks store the coefficients which feed into the multipliers in Filters A and B. There is a separate bank for each multiplier. Each bank can hold 256 12-bit coefficients. The banks are loaded using an LF InterfaceTM. There is a separate LF InterfaceTM for the Filter A and B banks. Coefficient bank loading is discussed in the LF InterfaceTM section. Configuration and Control Registers The configuration registers determine how the LF3320 operates. Tables 2 through 7 show the formats of the six configuration registers. There are three types of control registers: round, select, and limit. There are sixteen round registers for Filter A and sixteen for Filter B. Each register is 32 bits wide. RSLA3-0 and RSLB3-0 determine which Filter A and B round registers respectively are used for rounding. There are sixteen select registers for Filter A and sixteen for Filter B. Each register is 5 bits wide. RSLA3-0 and RSLB3-0 determine which Filter A and B select registers respectively are used in the select circuitry. TABLE 4. BITS 0 1 2 11-3 CONFIGURATION REGISTER 2 – ADDRESS 202H FUNCTION ALU Mode Filter B Pass A Filter B Pass B Filter B Reserved DESCRIPTION 0: A + B 1: B – A 0 : ALU Input A = 0 1 : ALU Input A = Forward Register Path 0 : ALU Input B = 0 1 : ALU Input B = Reverse Register Path Must be set to “0” TABLE 5. BITS 0 4-1 CONFIGURATION REGISTER 3 – ADDRESS 203H FUNCTION Filter B Odd-Tap Interleave Mode Filter B I/D Register Length DESCRIPTION 0 : Odd-Tap Interleave Mode Disabled 1 : Odd-Tap Interleave Mode Enabled 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 : : : : : : : : : : : : : : : : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Register Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers Registers 5 6 11-7 Filter B Tap Number Filter B Data Reversal Reserved 0 : Even Number of Taps 1 : Odd Number of Taps 0 : Data Reversal Enabled 1 : Data Reversal Disabled Must be set to “0” Output Limiting An output limiting function is provided for the overall filter, Filter A, and Filter B outputs. The Filter A limiting circuitry is used to limit the overall filter output (Single Filter Mode) and the Filter A output (Dual Filter Mode). The Filter B limiting circuitry is used to limit the Filter B output (Dual Filter Mode). The Filter A and B limit registers determine the valid range of output values for the Filter A and B limiting circuitry respectively. There are sixteen 32-bit user-programmable limit registers for both Filters A and B. The Filter A limit registers are used for the overall filter (Single Filter Mode) or Filter A (Dual Filter Mode). The Filter B limit registers are used for Filter B (Dual Filter Mode). RSLA3-0 determines which of the sixteen Filter A limit registers are used in the Filter A limit circuitry. RSLB3-0 determines which of the sixteen Filter B limit registers are used in the Filter B limit circuitry. A value of 0 on RSLA/RSLB3-0 selects Filter A/B limit register 0. A value of 1 selects Filter A/B limit register 1 and so on. Each limit Video Imaging Products 2-14 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter TABLE 6. BITS 0 1 11-2 There are sixteen limit registers for Filter A and sixteen for Filter B. Each register is 32-bits wide and stores both an upper and lower limit value. The lower limit is stored in bits 15-0 and the upper limit is stored in bits 31-16. RSLA3-0 and RSLB3-0 determine which Filter A and B limit registers respectively are used for limiting when limiting is enabled. Configuration and control register loading is discussed in the LF InterfaceTM section. LF Interface TM CONFIGURATION REGISTER 4 – ADDRESS 204H FUNCTION Filter B Limit Enable Filter A Limit Enable Reserved DESCRIPTION 0 : Limiting Disabled 1 : Limiting Enabled 0 : Limiting Disabled 1 : Limiting Enabled Must be set to “0” TABLE 7. BITS 0 1 2 3 4 5 11-6 CONFIGURATION REGISTER 5 – ADDRESS 205H FUNCTION Cascade Mode Single/Dual Filter Mode Filter B Input Output Adder Control Matrix Multiply Mode Accumulator Access Mode Reserved DESCRIPTION 0 : Last In Line 1 : First or Middle in Line 0 : Single Filter Mode 1 : Dual Filter Mode 0 : RIN11-0 1 : DIN11-0 0 : Filter A + Filter B 1 : Filter A + Filter B (Filter B Scaled by 2-12) 0 : Disabled 1 : Enabled 0 : Disabled 1 : Enabled Must be set to “0” The Filter A and B LF InterfacesTM are used to load data into the Filter A and B coefficient banks respectively. They are also used to load data into the configuration and control registers. The following section describes how the Filter A LF InterfaceTM works. The Filter A and B LF InterfacesTM are identical in function. If LDA and CFA11-0 are replaced with LDB and CFB11-0, the following section will describe how the Filter B LF InterfaceTM works. LDA is used to enable and disable the Filter A LF InterfaceTM. When LDA goes LOW, the Filter A LF InterfaceTM is enabled for data input. The first value fed into the interface on CFA11-0 is an address which determines what the interface is going to load. The three most significant bits (CFA11-9) determine if the LF InterfaceTM will load coefficient banks or Configuration/control registers (see Table 8). The nine least significant bits (CFA8-0) are the address for whatever is to be loaded (see Tables 9 through 14). For example, to load address 15 of the Filter A coefficient banks, the first data value into the LF InterfaceTM should be 00FH. To load Filter A limit register 10, the first data value should be C0AH. The first address value should be loaded into the interface on the same clock cycle that latches the HIGH to LOW transition of LDA (see Figures 17 and 18). The next value(s) loaded into the interface are the data value(s) which will be stored in the bank or register defined by the address value. When loading coefficient banks, the interface will expect eight values to be loaded into the device after the address value. The eight values are coefficients 0 through 7. When loading configuration or select registers, the interface will expect one value after the address value. When loading round or limit registers, the interface will expect four values after the address value. Figures 11 and 12 show the data loading sequences for the coefficient banks and Configuration/control registers. Both PAUSEA and PAUSEB allow the user to effectively slow the rate of data loading through the LF InterfaceTM. When PAUSEA is HIGH, the LF InterfaceTM affecting the data used for Filter A is held until PAUSEA is returned to a LOW. When PAUSEB is HIGH, the LF InterfaceTM affecting the data used for Filter B is held until PAUSEB is returned to a LOW. Figures 19 through 22 display the effects of both PAUSEA and PAUSEB while loading coefficient and control data. Table 15 shows an example of loading data into the coefficient banks. The following data values are written into address 10 of coefficient banks 0 through 7: 210H, 543H, C76H, 9E3H, 701H, 832H, F20H, 143H. Table 16 shows an example of loading data into a Configuration Register. Data value 003H is written into Configuration Register 4. Table 17 shows an example of loading data into a round register. Data value 7683F4A2H is written into Filter A round register 12. Table 18 shows an example of loading data into a select register. Data value 00FH is loaded into Filter A select register 2. Table 19 shows an example Video Imaging Products 2-15 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter sets can be updated in less than 27.7 µs, which is well within vertical blanking time. It takes 5S clock cycles to load S round or limit registers. Therefore, it takes 320 clock cycles to update all round and limit registers (both Filters A and B). Assuming an 83 MHz clock rate, all Filter A and B round/limit registers can be updated in 3.84 µs. The coefficient banks and Configuration/Control registers are not loaded with data until all data values for the specified address are loaded into the LF InterfaceTM. In other words, the coefficient banks are not written to until all eight coefficients have been loaded into the LF InterfaceTM. A round register is not written to until all four data values are loaded. COEFFICIENT SET 3 of loading data into Filter B limit register 7. Data value 3B60H is loaded as the lower limit and 72A4H is loaded as the upper limit. It takes 9S clock cycles to load S coefficient sets into the device. Therefore, it takes 2304 clock cycles to load all 256 coefficient sets. Assuming an 83 MHz clock rate, all 256 coefficient FIGURE 17. COEFFICIENT BANK LOADING SEQUENCE COEFFICIENT SET 1 COEFFICIENT SET 2 CLK W1 LDA/LDB W2 W3 CFA/CFB11-0 ADDR1 COEF0 COEF7 ADDR2 COEF0 COEF7 ADDR3 COEF0 COEF7 W1: Coefficient Set 1 written to coefficient banks during this clock cycle. W2: Coefficient Set 2 written to coefficient banks during this clock cycle. W3: Coefficient Set 3 written to coefficient banks during this clock cycle. FIGURE 18. CONFIGURATION/CONTROL REGISTER LOADING SEQUENCE CONFIG REG SELECT REG ROUND REGISTER LIMIT REGISTER CLK W1 LDA/LDB W2 W3 W4 CFA/CFB11-0 ADDR1 DATA1 ADDR2 DATA1 ADDR3 DATA1 DATA2 DATA3 DATA4 ADDR4 DATA1 DATA2 DATA3 DATA4 W1: Configuration Register loaded with new data on this rising clock edge. W2: Select Register loaded with new data on this rising clock edge. W3: Round Register loaded with new data on this rising clock edge. W4: Limit Register loaded with new data on this rising clock edge. FIGURE 19. COEFFICIENT BANK LOADING SEQUENCE WITH PAUSE IMPLEMENTATION COEFFICIENT SET 1 CLK W1 PAUSEA/PAUSEB LDA/LDB CFA/CFB11-0 ADDR1 COEF0 COEF1 COEF7 W1: Coefficient Set 1 written to coefficient banks during this clock cycle. Video Imaging Products 2-16 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter The Configuration and Control registers may be loaded with either the Filter A or B LF InterfacesTM. Since both LF InterfacesTM operate independently of each other, both LF InterfacesTM can load data into their respective coefficient banks at the same time. Or, one LF InterfaceTM can load the Configuration/Control registers while the other loads it’s respective coefficient banks. If both LF InterfacesTM are used to load a Configuration or Control register at the same time, the Filter B LF InterfaceTM will be given priority over the Filter A LF InterfaceTM. For example, if the Filter A LF InterfaceTM attempts to load data into a configuration register at the same time that the Filter B LF InterfaceTM attempts to load a Filter A round register, the Filter B LF InterfaceTM will be allowed to load the round register while the Filter A LF InterfaceTM will not be allowed to load the configuration register. However, the Filter A LF InterfaceTM will continue to function as if the write occurred. After the last data value is loaded, the interface will expect a new address value on the next clock cycle. After the next address value is loaded, data loading will begin again as previously discussed. As long as data is loaded into the interface, LDA must remain LOW. After all desired coefficient banks and Configuration/Control registers are loaded with data, the LF InterfaceTM must be disabled. This is done by setting LDA HIGH on the clock cycle after the clock cycle which latches the last data value. It is important that the LF InterfaceTM remain disabled when not loading data into it. The Filter A coefficient banks may only be loaded with the Filter A LF InterfaceTM and the Filter B coefficient banks may only be loaded with the Filter B LF InterfaceTM. TABLE 8. CFA/CFB11-9 DECODE 11 10 9 DESCRIPTION 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Coefficient Banks Configuration Registers Filter A Select Registers Filter B Select Registers Filter A Round Registers Filter B Round Registers Filter A Limit Registers Filter B Limit Registers FIGURE 20. CONFIGURATION AND SELECT REGISTER LOADING SEQUENCE WITH PAUSE IMPLEMENTATION CONFIGURATION REGISTER SELECT REGISTER CLK W1 PAUSEA/PAUSEB LDA/LDB W2 CFA/CFB11-0 ADDR1 DATA1 ADDR2 DATA1 W1: Configuration Register loaded with new data on this rising clock edge. W2: Select Register loaded with new data on this rising clock edge. FIGURE 21. ROUND REGISTER LOADING SEQUENCE WITH PAUSE IMPLEMENTATION ROUND REGISTER CLK W1 PAUSEA/PAUSEB LDA/LDB CFA/CFB11-0 ADDR1 DATA1 DATA2 DATA3 DATA4 W1: Round Register loaded with new data on this rising clock edge. Video Imaging Products 2-17 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter FIGURE 22. LIMIT REGISTER LOADING SEQUENCE WITH PAUSE IMPLEMENTATION LIMIT REGISTER CLK W1 PAUSEA/PAUSEB LDA/LDB CFA/CFB11-0 ADDR1 DATA1 DATA2 DATA3 DATA4 W1: Limit Register loaded with new data on this rising clock edge. TABLE 9. FLTR. A ROUND REGISTERS REGISTER 0 1 ADDRESS (HEX) 800 801 TABLE 10. FLTR.A SELECT REGISTERS REGISTER 0 1 ADDRESS (HEX) 400 401 TABLE 11. FLTR. A LIMIT REGISTERS REGISTER 0 1 ADDRESS (HEX) C00 C01 14 15 80E 80F 14 15 40E 40F 14 15 C0E C0F TABLE 12. FLTR. B ROUND REGISTERS REGISTER 0 1 ADDRESS (HEX) A00 A01 TABLE 13. FLTR.B SELECT REGISTERS REGISTER 0 1 ADDRESS (HEX) 600 601 TABLE 14. FLTR. B LIMIT REGISTERS REGISTER 0 1 ADDRESS (HEX) E00 E01 14 15 A0E A0F 14 15 60E 60F 14 15 E0E E0F Video Imaging Products 2-18 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter TABLE 15. COEFFICIENT BANK LOADING FORMAT CFA/B11 CFA/B10 CFA/B9 CFA/B8 CFA/B7 CFA/B6 CFA/B5 CFA/B4 CFA/B3 CFA/B2 CFA/B1 CFA/B0 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 0 1 0 0 1 0 0 0 1 0 1 0 0 0 1 0 1 1 0 1 1 0 0 0 0 1 0 0 0 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 0 1 1 0 0 1 0 1 0 0 1 0 0 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 1 0 1 1 1 0 1 0 1 0 0 1 0 1 1 0 0 1 1st Word - Address 2nd Word - Bank 0 3rd Word - Bank 1 4th Word - Bank 2 5th Word - Bank 3 6th Word - Bank 4 7th Word - Bank 5 8th Word - Bank 6 9th Word - Bank 7 TABLE 16. CONFIGURATION REGISTER LOADING FORMAT CFA/B11 CFA/B10 CFA/B9 CFA/B8 CFA/B7 CFA/B6 CFA/B5 CFA/B4 CFA/B3 CFA/B2 CFA/B1 CFA/B0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 1 1st Word - Address 2nd Word - Data TABLE 17. ROUND REGISTER LOADING FORMAT CFA/B11 CFA/B10 CFA/B9 CFA/B8 CFA/B7 CFA/B6 CFA/B5 CFA/B4 CFA/B3 CFA/B2 CFA/B1 CFA/B0 1 R R R R 0 R R R R 0 R R R R 0 R R R R 0 1 1 1 0** 0 0 1 0 1 0 1 1 0 1 0 0 1 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 1 1 0 0* 0 1 0 1st Word - Address 2nd Word - Data 3rd Word - Data 4th Word - Data 5th Word - Data TABLE 18. SELECT REGISTER LOADING FORMAT CFA/B11 CFA/B10 CFA/B9 CFA/B8 CFA/B7 CFA/B6 CFA/B5 CFA/B4 CFA/B3 CFA/B2 CFA/B1 CFA/B0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 0 1 1st Word - Address 2nd Word - Data TABLE 19. LIMIT REGISTER LOADING FORMAT CFA/B11 CFA/B10 CFA/B9 CFA/B8 CFA/B7 CFA/B6 CFA/B5 CFA/B4 CFA/B3 CFA/B2 CFA/B1 CFA/B0 1 R R R R 1 R R R R 1 R R R R 0 R R R R 0 0 0* 1 0** 0 1 0 0 1 0 1 1 1 1 0 0 1 0 1 0 0 1 0 0 1 0 0 1 0 1 0 1 0 1 1 0 1 0 0 1st Word - Address 2nd Word - Data 3rd Word - Data 4th Word - Data 5th Word - Data R = Reserved. Must be set to “0”. * This bit represents the MSB of the Lower Limit. ** This bit represents the MSB of the Upper Limit. Video Imaging Products 2-19 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter MAXIMUM RATINGS Above which useful life may be impaired (Notes 1, 2, 3, 8) Storage temperature .............................................................................................................. –65°C to +150°C Operating ambient temperature .............................................................................................. –55°C to +125°C VCC supply voltage with respect to ground .............................................................................. –0.5 V to +4.5 V Input signal with respect to ground ............................................................................................. –0.5 V to 5.5 V Signal applied to high impedance output .................................................................................... –0.5 V to 5.5 V Output current into low outputs ............................................................................................................... 25 mA Latchup current ................................................................................................................................. > 400 mA ESD Classification (MIL-STD-883E METHOD 3015.7) ......................................................................... Class 3 OPERATING CONDITIONS To meet specified electrical and switching characteristics Mode Active Operation, Commercial Active Operation, Military Temperature Range (Ambient) 0°C to +70°C –55°C to +125°C Supply Voltage 3.00 V ≤ VCC ≤ 3.60 V 3.00 V ≤ VCC ≤ 3.60 V ELECTRICAL CHARACTERISTICS Over Operating Conditions (Note 4) Symbol VOH VOL VIH VIL IIX IOZ I CC1 I CC2 CIN C OUT Parameter Output High Voltage Output Low Voltage Input High Voltage Input Low Voltage Input Current Output Leakage Current VCC Current, Dynamic VCC Current, Quiescent Input Capacitance Output Capacitance (Note 3) Test Condition VCC = Min., IOH = –4 mA VCC = Min., IOL = 8.0 mA Min 2.4 Typ Max Unit V 0.4 2.0 0.0 5.5 0.8 ±10 ±10 140 2 10 10 V V V µA µA mA mA pF pF Ground ≤ VIN ≤ VCC (Note 12) Ground ≤ VOUT ≤ VCC (Note 12) (Notes 5, 6) (Note 7) TA = 25°C, f = 1 MHz TA = 25°C, f = 1 MHz Video Imaging Products 2-20 08/16/2000–LDS.3320-N 432109876543210987654321 432109876543210987654321 432109876543210987654321 432109876543210987654321 *DISCONTINUED SPEED GRADE 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 10 10 Min DEVICES INCORPORATED Symbol COMMERCIAL OPERATING RANGE (0°C to +70°C) Notes 9, 10 (ns) SWITCHING WAVEFORMS: SWITCHING CHARACTERISTICS CONTROLS (Except OED & OEC) ROUT11-0/COUT11-0 tENA tDIS t DCC tD t HCC t SCC t HCT t SCT tH tS tPWH tPWL t CYC DOUT15-0 Parameter Three-State Output Enable Delay (Note 11) Three-State Output Disable Delay (Note 11) Cascade Output Delay Output Delay Hold Time Coefficient Control Inputs Setup Time Coefficient Control Inputs Hold Time Control Inputs Setup Time Control Inputs Input Hold Time Input Setup Time Clock Pulse Width High Clock Pulse Width Low Cycle Time DIN11-0 RIN11-0 CAA7-0 CAB7-0 OED OEC CLK tSCC tSCT tS CAA/CABN DIN/RINN tHCC tHCT tH 1 DATA I/O CAA/CABN+1 DIN/RINN+1 2 tDIS tDIS HIGH IMPEDANCE HIGH IMPEDANCE tPWH 3 2-21 tCYC tENA tENA 0 0 0 8 8 8 25 tPWL 25* Max 13 13 15 15 4 Horizontal Digital Image Filter Min 18 0 0 0 6 8 6 6 8 18* Video Imaging Products 5 Max 11 11 13 13 LF3320– Min 15 0 0 0 5 5 7 5 7 15 6 Max 12 12 OUTPUTN-1 OUTPUTN-1 9 9 08/16/2000–LDS.3320-N tDCC Min tD 12 0 0 0 4 4 5 4 5 LF3320 7 12 OUTPUTN OUTPUTN Max 7.5 7 10 10 432109876543210987654321 432109876543210987654321 432109876543210987654321 432109876543210987654321 *DISCONTINUED SPEED GRADE Symbol PAUSEA PAUSEB CFA11–0 CFB11–0 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 1 765432109876543210987654321 765432109876543210987654321 765432109876543210987654321 76543210987654321098765432 Min DEVICES INCORPORATED SWITCHING WAVEFORMS: COMMERCIAL OPERATING RANGE (0°C to +70°C) Notes 9, 10 (ns) tPH tPS tLH tLS tCFH t CFS CLK LDA LDB Parameter PAUSE Hold Time PAUSE Setup Time Load Hold Time Load Setup Time Coefficient Input Hold Time Coefficient Input Setup Time tCFS tLS ADDRESS tCFH 1 tPWH LF INTERFACETM tCYC CF0 tPWL 2 tPS 3 2-22 0 0 0 8 8 8 25* Max tPH 4 Horizontal Digital Image Filter Min 0 0 0 7 6 6 18* Max Video Imaging Products LF3320– CF1 tLH 5 Min 0 0 0 6 5 6 15 Max 08/16/2000–LDS.3320-N CF2 Min 5.5 0 0 0 4 4 LF3320 6 12 Max LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter NOTES 1. Maximum Ratings indicate stress specifications only. Functional operation of these products at values beyond those indicated in the Operating Conditions table is not implied. Exposure to maximum rating conditions for extended periods may affect reliability. 2. The products described by this specification include internal circuitry designedto protect the chipfrom damaging substrate injection currents and accumulations of static charge. Nevertheless, conventional precautions should be observed during storage, handling, and use of these circuits in order to avoid exposure to excessive electrical stress values. input transition times less than 3 ns, output reference levels of 1.5 V (except tDIS test), and input levels of nominally 0 to 3.0 V. Output loading may be a resistive divider which provides for specified IOH and IOL at an output voltage of VOH min and VOL max respectively. Alternatively, a diode bridge with upper and lower current sources of I OH and I OL respectively, and a balancing voltage of 1.5 V may be used. Parasitic capacitance is 30 pF minimum, and may be distributed. measured to the 1.5 V crossing point with datasheet loads. For the tDIS test, the transition is measured to the ±200mV level from the measured steady-state output voltage with ±10mA loads. The balancing voltage, V TH , is set at 3.0 V for Z-to-0 and 0-to-Z tests, and set at 0 V for Z-to-1 and 1-to-Z tests. 12. These parameters are only tested at the high temperature extreme, which is the worst case for leakage current. This device has high-speed outputs capable of large instantaneous current pulses and fast turn-on/turn-off times. As a result, care must be exercised in the testing of this device. The following 3. This device provides hard clamping measures are recommended: of transient undershoot. Input levels below ground will be clamped begin- a. A 0.1 µF ceramic capacitor should be ning at –0.6 V. The device can withstand installed between VCC and Ground indefinite operation with inputs or out- leads as close to the Device Under Test puts in the range of –0.5 V to +5.5 V. (DUT) as possible. Similar capacitors Device operation will not be adversely should be installed between device VCC affected, however, input current levels and the tester common, and device will be well in excess of 100 mA. ground and tester common. 4. Actual test conditions may vary from b. Ground and VCC supply planes must those designated but operation is guar- be brought directly to the DUT socket or anteed as specified. contactor fingers. 5. Supply current for a given applica- c. Input voltages on a test fixture should tion can be accurately approximated be adjusted to compensate for inductive by: ground and VCC noise to maintain required DUT input levels relative to the NCV2 F DUT ground pin. where 4 10. Each parameter is shown as a mini- FIGURE A. OUTPUT LOADING CIRCUIT DUT S1 IOL CL IOH VTH FIGURE B. THRESHOLD LEVELS tENA OE Z 0 1.5 V 1.5 V 1.5 V tDIS 3.0V Vth VOL* 0.2 V 0 1 Z Z 1.5 V VOH* 0.2 V Z 1 0V Vth VOL* Measured VOL with IOH = –10mA and IOL = 10mA VOH* Measured VOH with IOH = –10mA and IOL = 10mA mum or maximum value. Input requirements are specified from the point of view of the external system driving the chip. Setup time, for example, is specified as a minimum since the external system must 6. Tested with outputs changing every supply at least that much time to meet the cycle and no load, at a 40 MHz clock rate. worst-case requirements of all parts. Responses from the internal circuitry are 7. Tested with all inputs within 0.1 V of specified from the point of view of the VCC or Ground, no load. device. Output delay, for example, is 8. These parameters are guaranteed but specified as a maximum since worstcase operation of any device always pronot 100% tested. vides data within that time. 9. AC specifications are tested with 11. For the tENA test, the transition is N = total number of device outputs C = capacitive load per output V = supply voltage F = clock frequency Video Imaging Products 2-23 08/16/2000–LDS.3320-N LF3320 DEVICES INCORPORATED Horizontal Digital Image Filter ORDERING INFORMATION 144-pin GND ROUT11 ROUT10 ROUT9 ROUT8 ROUT7 ROUT6 ROUT5 ROUT4 ROUT3 ROUT2 ROUT1 ROUT0 GND VCC SHENA TXFRA GND CLK VCC TXFRB SHENB RIN0 RIN1 RIN2 RIN3 RIN4 RIN5 RIN6 RIN7 RIN8 RIN9 RIN10 RIN11 OEC VCC VCC DIN11 DIN10 DIN9 DIN8 DIN7 DIN6 DIN5 DIN4 DIN3 DIN2 DIN1 DIN0 GND VCC CENA CAA7 CAA6 CAA5 CAA4 CAA3 CAA2 CAA1 CAA0 CFA11 CFA10 CFA9 CFA8 CFA7 CFA6 CFA5 CFA4 CFA3 CFA2 CFA1 CFA0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 Top View 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 GND COUT11 COUT10 COUT9 COUT8 COUT7 COUT6 COUT5 COUT4 COUT3 COUT2 COUT1 COUT0 GND VCC CENB CAB7 CAB6 CAB5 CAB4 CAB3 CAB2 CAB1 CAB0 CFB11 CFB10 CFB9 CFB8 CFB7 CFB6 CFB5 CFB4 CFB3 CFB2 CFB1 CFB0 Speed 0°C to +70°C — COMMERCIAL SCREENING 15 ns 12 ns LF3320QC15 LF3320QC12 LDA PAUSEA ACCA RSLA3 RSLA2 RSLA1 RSLA0 VCC GND DOUT15 DOUT14 DOUT13 DOUT12 DOUT11 DOUT10 DOUT9 DOUT8 GND OED DOUT7 DOUT6 DOUT5 DOUT4 DOUT3 DOUT2 DOUT1 DOUT0 GND VCC RSLB0 RSLB1 RSLB2 RSLB3 ACCB PAUSEB LDB 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 Plastic Quad Flatpack (Q5) Video Imaging Products 2-24 08/16/2000–LDS.3320-N