1503S36UR

www.make-ps.com E-mail:info@make-ps.com 1500UR series Single & Dual Output DC/DC Converter FEATURES • 6 sided Continuous Shielding • 4:1 Ultra-Wide Input Voltage Range • Output Voltage Trim (Single Output only) • -25oC to +75oC Operating Temperature Range • Efficiency to 83% • 1400 VDC Input/Output Isolation • 9.4W/In3 Power Density DESCRIPTIONS The 1500UR series is a family of miniature 15W DC/DC converters specifically designed for board mount power distribution applications where space is critical, but performance and power cannot be sacrificed. Standard features include an ultra-wide 4:1 input voltage range, efficiency as high as 83% and continuous short circuit protection by input current limiting. 14 models operate from (4:1) input voltage ranges of 10 to 40 VDC or 18 to 72 VDC and provide tightly regulated outputs of 3.3, 5, 12, 15, ±5, ±12 or ±15 VDC. All models are packaged in a compact, low profile 2” X 2” X 0.4” metal case. INPUT CHARACTERISTICS Min Typ Max Unit/Comments Input Voltage 20 VDC Input Models 36 VDC Input Models Input Fuse Requirements 20 VDC Input Models 36 VDC Input Models Reverse Polarity Input Current Input Filter 10 18 20 36 2000 1000 12 40 72 VDC VDC mA; Slow blow type mA; Slow blow type Amp LC Type OUTPUT CHARACTERISTICS Min Typ Max Unit/Comments Output Voltage Accuracy ±100 mV 1 3.3V Outputs ±1.0 % 1 All Other Models Voltage Balance: ±2.0 %; Equal Output Loads Dual Outputs Voltage Trim Range (Single Only) ±3.0 % 3.3 Vout ±5.0 %; Output Voltage All Other Models ±1.0 % 2 Line Regulation ±1.0 % 3 Load Regulation Ripple/Noise 100 mV; p-p, Nom.Line FL, 3.3V Outputs 20Mhz B.W. using 1 μf bypass capacitor 1.25 %; p-p, Nom.Line FL, All Other Models 20Mhz B.W. using 1μf bypass capacitor Continuous, AutoShort Circuit Protection matic Recovery 300 μS to within1% error Transient Recovery Time band for 50% step load change ±0.02 % per oC Temperature Coefficient GENERAL CHARACTERISTICS Switching Frequency Isolation Voltage Isolation Resistance Isolation Capacitance MTBF (MIL-HBK-217F) Min Typ Max Unit/Comments kHz 130 VDC, 1 minute 1400 Mohm, 500VDC 1000 pF, 100kHz, 1Volt 100 Thousand Hours, 865 +25oC, Ground Benign 1 2 3 = Output voltage at nominal line & FL = Output voltage measured from minimum input line to maximum = Output voltage measured from FL to 10% Load >> B-137 www.make-ps.com ENVIRONMENTAL SPECIFICATIONS Operating Temp. Range Storage Temp. Range Relative Humidity Cooling Min -25 -55 Typ Max +75 +125 +95 Unit/Comments C; Ambient o C % Humidity; noncondensing Free-Air Convection o E-mail:info@make-ps.com PHYSICAL CHARACTERISTICS Case Size Case Material Shield Connection 20 VDC Input Models 36 VDC Input Models Flammability Weight Unit/Comments 2.0 X 2.0 X 0.4 inches (51.0 X 51.0 X 10.2 mm) Coated Metal with NonConductive Base Negative Input, Pin 2 Positive Input, Pin 1 UL94V-0 79 Grams OUTLINE DRAWING 2.00 (50.8) 0.40 (10.2) 0.40 (10.2) 0.60 (15.2) 3 +Vout 4 5 0.040± .005 (1.01) DIA. 2.00 0.80 (50.8) (20.3) COM -Vout BOTTOM +Vin -Vin 1 2 SIDE 0.60 (15.2) 0.90 (22.9) 0.22MIN. (5.6) 0.40 (10.2) 0.20 (5.1) PIN OUT CHART Pins 1 2 3 4 5 Single +Vin - Vin + Vout Trim - Vout Dual + Vin - Vin + Vout ± Common - Vout Notes: 1. Unless otherwise specified dimensions are in inches (mm). Tolerances Inches mm X.XX = ±0.02 X.X = ±0.5 X.XXX= ±0.010 X.XX = ±0.25 All specifications are typical at nominal input, nominal load and 25° C unless otherwise specified. External, low ESR, 10 microfarad (minimum) capacitor across output is recommended for operation. >> B-138 www.make-ps.com HOW TO ORDER E-mail:info@make-ps.com HOW TO ORDER 15 XX D XX UR Wattage Output Voltage Output Configuration (S=Single,D=Dual) Series Nominal Input Voltage MODEL SELECTION CHART Model Nominal Input Voltage (VDC) 20 20 20 20 20 20 20 36 36 36 36 36 36 36 Output Voltage (VDC) Full Load Output Current (mA) 4500 3000 1250 1000 ±1500 ±625 ±500 4500 3000 1250 1000 ±1500 ±625 ±500 No Load Input Current (mA) 40 40 40 40 40 40 40 40 40 40 40 40 40 40 Full Load Input Current (mA) 900 900 960 950 920 960 1000 500 500 510 500 510 520 520 Output Over Voltage (V) Efficiency @ FL (%) 1503S20UR 1505S20UR 1512S20UR 1515S20UR 1505D20UR 1512D20UR 1515D20UR 1503S36UR 1505S36UR 1512S36UR 1515S36UR 1505D36UR 1512D36UR 1515D36UR 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 5.8 6.8 15 18 ±6.8 ±15 ±18 5.8 6.8 15 18 ±6.8 ±15 ±18 82 83 78 79 81 78 75 82 83 81 83 81 80 80 >> B-139 www.make-ps.com OUTPUT VOLTAGE TRIM (1500UR SERIES, SINGLE OUTPUT ONLY) E-mail:info@make-ps.com The converter’s output voltage may be trimmed to ±5% of the nominal output voltage. TRIM UP Trim output voltage up by connecting an external resistor between Pins 4 and 5. Use the following equation. Reference Table 1 for variable A. Radj-up = Example: A Δ% - 24 (kΩ) If we want to trim 5% up for 12V output units, where A = 1.97, Δ % = 0.05 Radj-up = 1.97 0.05 - 24 kΩ = 15.4 kΩ Table 1. Output Voltage A 3.3V 5V 12V 15V 0.75 1.25 1.97 2.07 TRIM DOWN Trim output voltage down by connecting an external resistor between Pins 3 and 4. Use the following equation. Reference Table 2 for variable C and D. Radj-down = Example: C Δ% - D (kΩ) If we want to trim 2% down for 5V output units, where C = 1.25, D = 26.5, Δ % = 0.02 Radj-down = 1.25 0.02 - 26.5 kΩ = 36 kΩ Table 2. Output Voltage C D 3.3V 5V 12V 15V 1.25 1.25 7.55 10.3 26 26.5 33.5 36.4 >> B-140