APT15GN120BDQ1

TYPICAL PERFORMANCE CURVES APT15GN120BDQ1 APT15GN120BDQ1(G) APT15GN120BD_SDQ1(G) APT15GN120SDQ1 APT15GN120SDQ1(G) 1200V *G Denotes RoHS Compliant, Pb Free Terminal Finish. Utilizing the latest Field Stop and Trench Gate technologies, these IGBT's have ultra low VCE(ON) and are ideal for low frequency applications that require absolute minimum conduction loss. Easy paralleling is a result of very tight parameter distribution and a slightly positive VCE(ON) temperature coefficient. Low gate charge simplifies gate drive design and minimizes losses. (B) TO -2 47 D3PAK (S) C G E • 1200V Field Stop • Trench Gate: Low VCE(on) • Easy Paralleling G C E C G E Applications: Welding, Inductive Heating, Solar Inverters, SMPS, Motor drives, UPS MAXIMUM RATINGS Symbol VCES VGE I C1 I C2 I CM SSOA PD TJ,TSTG TL Parameter Collector-Emitter Voltage Gate-Emitter Voltage Continuous Collector Current @ TC = 25°C Continuous Collector Current @ TC = 110°C Pulsed Collector Current 1 All Ratings: TC = 25°C unless otherwise specified. APT15GN120BD_SDQ1(G) UNIT Volts 1200 ±30 45 22 45 45A @ 1200V 195 -55 to 150 Amps Switching Safe Operating Area @ TJ = 150°C Total Power Dissipation Operating and Storage Junction Temperature Range Max. Lead Temp. for Soldering: 0.063" from Case for 10 Sec. Watts °C 300 STATIC ELECTRICAL CHARACTERISTICS Symbol V(BR)CES VGE(TH) VCE(ON) Characteristic / Test Conditions Collector-Emitter Breakdown Voltage (VGE = 0V, I C = 0.5mA) Gate Threshold Voltage (VCE = VGE, I C = 600µA, Tj = 25°C) MIN TYP MAX Units 1200 5.0 1.4 2 2 5.8 1.7 2.0 6.5 2.1 Volts Collector-Emitter On Voltage (VGE = 15V, I C = 15A, Tj = 25°C) Collector-Emitter On Voltage (VGE = 15V, I C = 15A, Tj = 125°C) I CES I GES RGINT Collector Cut-off Current (VCE = 1200V, VGE = 0V, Tj = 25°C) 200 TBD 120 N/A µA nA Ω 7-2009 050-7598 Rev C Collector Cut-off Current (VCE = 1200V, VGE = 0V, Tj = 125°C) Gate-Emitter Leakage Current (VGE = ±20V) Intergrated Gate Resistor CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. Microsemi Website - http://www.microsemi.com DYNAMIC CHARACTERISTICS Symbol Cies Coes Cres VGEP Qg Qge Qgc SSOA td(on) tr td(off) tf Eon1 Eon2 Eoff td(on) tr td(off) tf Eon1 Eon2 Eoff Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Gate-to-Emitter Plateau Voltage Total Gate Charge 3 APT15GN120BD_SDQ1(G) Test Conditions Capacitance VGE = 0V, VCE = 25V f = 1 MHz Gate Charge VGE = 15V VCE = 600V I C = 15A TJ = 150°C, R G = 4.3Ω 7, VGE = 15V, L = 100µH,VCE = 1200V Inductive Switching (25°C) VCC = 800V VGE = 15V I C = 15A 4 5 MIN TYP MAX UNIT 1200 65 50 9.0 90 5 55 45 10 9 150 110 410 730 950 10 9 170 185 475 1310 1300 µJ ns ns A nC V pF Gate-Emitter Charge Gate-Collector ("Miller ") Charge Switching Safe Operating Area Turn-on Delay Time Current Rise Time Turn-off Delay Time Current Fall Time Turn-on Switching Energy RG = 4.3Ω 7 TJ = +25°C Turn-on Switching Energy (Diode) Turn-off Switching Energy Turn-on Delay Time Current Rise Time Turn-off Delay Time Current Fall Time Turn-on Switching Energy 44 6 µJ Inductive Switching (125°C) VCC = 800V VGE = 15V I C = 15A RG = 4.3Ω 7 55 Turn-on Switching Energy (Diode) Turn-off Switching Energy 66 TJ = +125°C THERMAL AND MECHANICAL CHARACTERISTICS Symbol RθJC RθJC WT Characteristic Junction to Case (IGBT) Junction to Case (DIODE) Package Weight MIN TYP MAX UNIT °C/W gm .64 1.18 5.9 1 Repetitive Rating: Pulse width limited by maximum junction temperature. 2 For Combi devices, Ices includes both IGBT and FRED leakages 3 See MIL-STD-750 Method 3471. 4 Eon1 is the clamped inductive turn-on energy of the IGBT only, without the effect of a commutating diode reverse recovery current adding to the IGBT turn-on loss. Tested in inductive switching test circuit shown in figure 21, but with a Silicon Carbide diode. 7-2009 Rev C 050-7598 5 Eon2 is the clamped inductive turn-on energy that includes a commutating diode reverse recovery current in the IGBT turn-on switching loss. (See Figures 21, 22.) 6 Eoff is the clamped inductive turn-off energy measured in accordance with JEDEC standard JESD24-1. (See Figures 21, 23.) 7 RG is external gate resistance, not including RGint nor gate driver impedance. (MIC4452) Microsemi Reserves the right to change, without notice, the specifications and information contained herein. TYPICAL PERFORMANCE CURVES 60 V GE APT15GN120BD_SDQ1(G) 60 15V IC, COLLECTOR CURRENT (A) 50 13V 40 12V 11V 10V 9V 10 0 8V 7V = 15V IC, COLLECTOR CURRENT (A) 50 40 TJ = 125°C 30 TJ = 25°C 20 TJ = -55°C 10 0 30 20 0 1 2 3 4 5 6 VCE, COLLECTER-TO-EMITTER VOLTAGE (V) 250µs PULSE TEST