DLP11SN331HL2L.

Noise Suppression Products/EMI Suppression Filters > Chip Common Mode Choke Coils > Film Type Data Sheet 1 Chip Common Mode Choke Coils Film Type DLP11S Series (0504 Size) ■ Dimension ■ Equivalent Circuit (1) 0.55±0.1 (2) (3) (4) (1) (2) (4) (3) 1.0±0.1 0.82±0.1 0.3±0.1 +0.1 No polarity. 0.25 -0.05 1.25±0.1 (in mm) ■ Impedance-Frequency ■ Impedance-Frequency Characteristics DLP11SA DLP11SN 10000 1000 DLP11SN331HL2 DLP11SN281HL2 1000 Common mode Common mode DLP11SN241HL2 DLP11SN201HL2 DLP11SN161SL2 DLP11SN121SL2 DLP11SN900HL2 DLP11SN670SL2 Impedance (Ω) Impedance (Ω) 100 DLP11SA900HL2 DLP11SA670HL2 DLP11SA350HL2 100 DLP11SN331HL2 DLP11SN281HL2 DLP11SN241HL2 DLP11SN201HL2 10 10 DLP11SA900HL2 DLP11SA670HL2 DLP11SA350HL2 Differential mode DLP11SN161SL2 DLP11SN121SL2 Differential mode DLP11SN900HL2 DLP11SN670SL2 1 1 10 100 Frequency (MHz) 1000 10000 1 1 10 100 Frequency (MHz) 1000 10000 ■ Differential Mode Transmission Characteristics (Typ.) ■ Differential Mode Transmission Characteristics (Typ.) DLP11SA DLP11SN 0.0 0 DLP11SN900HL2 DLP11SA900HL2 2.0 Insertion Loss (dB) Insertion Loss (dB) 5 4.0 6.0 10 15 8.0 20 10.0 1 10 100 Frequency (MHz) 1000 10000 1 10 100 Frequency (MHz) 1000 10000 Continued on the following page. o This data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2007.11.1 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Chip Common Mode Choke Coils > Film Type Data Sheet 2 Continued from the preceding page. ■ Packaging Code Packaging Minimum Quantity L 180mm Embossed Tape 3000 B Bulk(Bag) 500 ■ Rated Value (p: packaging code) Part Number Common Mode Impedance Rated Current Rated Voltage (at 100MHz/20°C) Insulation Resistance (min.) Withstand Voltage DC Resistance Operating Number of Circuit Temperature Range DLP11SA350HL2p 35ohm±20% 170mA 5Vdc 100M ohm 12.5Vdc 0.9ohm±25% -40°C to 85°C 1 DLP11SA670HL2p 67ohm±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.2ohm±25% -40°C to 85°C 1 DLP11SN670SL2p 67ohm±20% 180mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% -40°C to 85°C 1 DLP11SA900HL2p 90ohm±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.4ohm±25% -40°C to 85°C 1 DLP11SN900HL2p 90ohm±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.5ohm±25% -40°C to 85°C 1 DLP11SN121SL2p 120ohm±20% 140mA 5Vdc 100M ohm 12.5Vdc 2.0ohm±25% -40°C to 85°C 1 DLP11SN161SL2p 160ohm±20% 120mA 5Vdc 100M ohm 12.5Vdc 2.7ohm±25% -40°C to 85°C 1 DLP11SN201HL2p 200ohm±20% 110mA 5Vdc 100M ohm 12.5Vdc 3.1ohm±25% -40°C to 85°C 1 DLP11SN241HL2p 240ohm±20% 100mA 5Vdc 100M ohm 12.5Vdc 3.5ohm±25% -40°C to 85°C 1 DLP11SN281HL2p 280ohm±20% 90mA 5Vdc 100M ohm 12.5Vdc 4.2ohm±25% -40°C to 85°C 1 DLP11SN331HL2p 330ohm±20% 80mA 5Vdc 100M ohm 12.5Vdc 4.9ohm±25% -40°C to 85°C 1 ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2007.11.1 http://www.murata.com/