SF2079E

RFM products are now Murata products. SF2079E • • • • Precision UHF SAW Filter 3.0 X 3.0 X 1.2 mm Surface-mount Case Differential Input and Output Complies with Directive 2002/95/EC (RoHS) 251.045 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm DC Voltage on any Non-ground Terminal 30 VDC Operating Temperature Range -40 to +85 °C Component Storage Temperature Range -60 to +95 °C Suitable for Lead-free Soldering - Maximum Soldering Profile 260 °C for 30 s SM3030-8 Electrical Characteristics Characteristic Center Frequency Insertion Loss Amplitude Ripple: (fc - 6.2500) to (fc - 4.3925) MHz (fc - 4.3925) to (fc - 2.5350) MHz (fc - 2.5350) to (fc - 0.0250) MHz (fc + 0.0250) to (fc + 2.5350) MHz (fc + 2.5350) to (fc + 4.3925) MHz (fc + 4.3925) to (fc + 6.2500) MHz 1.5 dB Bandwidth centered at fc 3.0 dB Bandwidth centered at fc Low Side Attenuation < fc - 16.5 MHz Low Side Attenuation, 234.545 to 240.545 MHz (fc - 10.5 MHz) High Side Attenuation, 260.045 to 267.545 MHz (fc + 9.0 MHz) High Side Attenuation > fc + 16.5 MHz Temperature Coefficient of frequency Group Delay Ripple: (fc - 6.2500) to (fc - 4.3925) MHz (fc - 4.3925) to (fc - 2.5350) MHz (fc - 2.5350) to (fc - 0.0250) MHz (fc + 0.0250) to (fc + 2.5350) MHz (fc + 2.5350) to (fc + 4.3925) MHz (fc + 4.3925) to (fc + 6.2500) MHz Source/Load Impedance Case Style Lid Symbolization (YY=year, WW=week, S=shift) See note 4 Sym fC IL Notes Min 1 1, 2 35 32 14 30 Typ Max Units 251.045 12.5 15.0 MHz dB 1.3 0.5 0.5 0.7 0.6 0.9 13.4 14.1 38 34 26 35 2.0 1.5 1.5 1.5 1.5 2.5 MHz dB -18 1, 2, 3 6 dBP-P ppm/K 44 90 37 70 39 120 nsP-P 40 120 34 70 37 90 150 ohms SM3030-8 3.0 x 3.0 mm Nominal Footprint 829 YWWS CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. NOTES: 1. 2. 3. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout 4. 5. 6. 7. ©2010-2014 byMurata Murata Electronics N.A., Inc. Copyright © Manufacturing Co., Ltd. All Rights Reserved 2009 SF2079E (R) 4/4/14 Page 1 of 5 and external impedance matching design. See Application Note No. 42 for details. The design, manufacturing process, and specifications of this filter are subject to change. Tape and Reel Standard Per ANSI / EIA 481. US and international patents may apply. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd. www.murata.com ©2010-2014 © byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2009 SF2079E (R) 4/4/14 Page 2 of 5 www.murata.com PCB J1,J2,J3,J4 L1,L2 L3,L4 C1 C2 C3 C4 401-1724-001 500-1279-001 501-1068-390 501-1068-470 501-0857-150 501-0857-120 501-0857-010 501-0857-005 PCB, DEMO, 3.0 or 3.8 PKG, PINS 1&2 IN, 5&6 OUT CONNECTOR, SMA FEMALE, END LAUNCH, 062” THICK PCB INDUCTOR, CHIP, 39 nH 0603 INDUCTOR, CHIP, 47 nH 0603 CAPACITOR, CHIP, 15 pF 0402 CAPACITOR, CHIP, 12 pF 0402 CAPACITOR, CHIP, 1.0 pF 0402 CAPACITOR, CHIP, 0.5 pF 0402 ©2010-2014 © byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2009 SF2079E (R) 4/4/14 Page 3 of 5 www.murata.com 8-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension J J I J K N I A B C D E F G H I J K L M N O L M N mm Nom 3.0 3.0 1.27 0.92 0.75 0.60 0.60 1.20 3.19 0.81 0.96 0.81 1.39 0.23 0.38 Min 2.87 2.87 1.14 0.79 0.62 0.47 0.47 1.07 Max 3.13 3.13 1.40 1.05 0.88 0.73 0.73 1.33 Min 0.113 0.113 0.045 0.031 0.024 0.018 0.018 0.042 Inches Nom 0.118 0.118 0.050 0.036 0.029 0.024 0.024 0.047 0.126 0.032 0.038 0.032 0.055 0.009 0.015 Max 0.123 0.123 0.055 0.041 0.034 0.029 0.029 0.052 Case Materials Materials K O O Solder Pad Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel Lid Plating 2.0 to 3.0 µm Nickel Body Al2O3 Ceramic Pb Free PCB Footprint Top View TOP VIEW BOTTOM VIEW 3 829 YWWS 2 8 7 1 6 6 2 5 5 3 7 1 A E C B 8 H G 4 4 D ©2010-2014 © byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2009 SF2079E (R) 4/4/14 Page 4 of 5 F www.murata.com Inches "B" REF. 100 REF. Tape and Reel Specifications “B” millimeters Quantity Per Reel 7 178 500 13 330 3000 See Detail "A" 13. 0 12.0 20 Ao 3.35 mm Bo 3.35 mm Ko 1.4 mm Pitch 8.0 mm W 12.0 mm .2 2.0 Carrier Tape Dimensions COMPONENT ORIENTATION 2.0 4.0 A 1.5 PIN #1 1.75 0.3 3.35 B 12.0 5.5 RO.3 (MAX.) B 3.35 8.0 A 1.4 R0.5 (TYP.) 1.5 SECTION A-A SECTION B-B ©2010-2014 © byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2009 SF2079E (R) 4/4/14 Page 5 of 5 USER DIRECTION OF FEED www.murata.com