EVPBL9A2B000

Light Touch Switches/EVPBL 2.8 mm×1.9 mm SMD Light Touch Switches Type: EVPBL ■ Features ● External dimensions: 2.8 mm×1.9 mm, Height 0.53 mm, 0.57 mm, 0.60mm ● High operability equipped with an actuator (push plate) ● IP67 ■ Recommended Applications ● Operation switches for portable electronic equipments (Mobile phone, Portable audio) ■ Explanation of Part Numbers(Standard specification only) 1 2 3 4 5 B L Product Code Type 6 7 8 9 A Operating Force 10 11 12 0 0 0 Height Packing unit B 16,000 pcs. F 20,000 pcs. ■ Specifications Type Snap action/Push-on type SPST Rating 10 μA 2 V DC to 20 mA 15 V DC (Resistive load) Contact Resistance Electrical 500 mΩ max. Insulation Resistance Mechanical Endurance 50 MΩ min. (at 100 V DC) Dielectric With standing Voltage 250 V AC for 1 minute Bouncing 10 ms max. (ON, OFF) 1.6 N, 2.25 N, 3.0N Operating Force Travel 0.15 mm Operating Life Protective Structure 300,000 cycles min. IP67(＊1) Operating Temperature –40 °C to +85 °C –40 °C to +85 °C (Bulk) –20 °C to +60 °C (Taping) Storage Temperature Minimum Quantity/Packing Unit Dust resistance : 4 types of talc 8 h, Water resistance : Immersion depth 1 m 30 min. 1.6 N, 2.25 N : 16,000 pcs. Embossed Taping (Reel Pack) 3.0 N : 20,000 pcs. Embossed Taping (Reel Pack) 1.6 N, 2.25 N : 80,000 pcs. 3.0 N : 100,000 pcs. Quantity/Carton Note: Non washable (＊1) IP 67 : Switch shall not be operated during test. Water or dust ingress shall be limited enough to prevent deleterious effect to the switch function. However, IP67 shall be guaranteed under single product state, then there is a possibility that IP67 performance become impaired depending on your mounting condition or usage. So, please ask us in advance, if the switch is applied to important usage for water and dust resistant. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 2020.02 LQGXVWULDOSDQDVRQLFFRPDFH 1 © Panasonic Corporation 2020 ANCTB104E 202002 Light Touch Switches/EVPBL ■ Dimensions in mm (not to scale) EVPBL (Embossed Taping) General dimension tolerance : ±0.1 （ ） dimensions are reference dimensions. (Without the remainder of the molding gate and the film) This reference specifications are subject to change. H （0.35） A' B B' 1.9±0.15 A （φ0.85） 2.8±0.15 2-3(Terminal) Ａ 0.1max. 0.1max. 2-1.5 2-0.75 （2-2.18） Ｂ Ａ Ｂ' This product is designed to be smaller than the conventional type, which lowered the film peel off strength. Therefore please avoid to apply force to a push plate from side, or/and avoid set-knob to touch push plate during insertion to a set-case. :Recommended land pattern area. :No soldering area. Ａ' No soldering 0.6 1.72 （1.9） Circuit Diagram Molding gate Solder thickness t=0.08±0.01 （1.8） Ｂ Ｂ' 2.14 3.4 Part Numbers Ａ' • Any land pattern or via holes shall not be provided at area. • If it's necessary to design land pattern or via holes at area. please apply resist to them to protect their metal part completely. • If their metal parts are not protected completely,short circuit failure may occur by solder ball. • Beside, there should be convexoconcave by designing additional pattern, it may cause swith tilt, influence on solder-ability or flux intrusion after reflow soldering. • Therefore, please study any influence of additional land pattern or via holes at area in advance. Operating Force H=Height Operating Life EVPBL2A1B000 1.6 N 0.53 mm 300,000 cycles EVPBL9A2B000 2.25 N 0.57 mm 300,000 cycles EVPBL5A8F000 3.0 N 0.60 mm 300,000 cycles Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Panasonic Corporation Electromechanical Control Business Division industrial.panasonic.com/ac/e/ 2 © Panasonic Corporation 2020 ANCTB104E 202002 Light Touch Switches/EVPBL ■ Recommended Reflow Soldering Conditions Switch Top（°C） MAX. 245 Cooling 220 180 150 ＊Reflow temperature may vary by location even in the same reflow condition. Please check the reflow temperature at terminals and at the top of a switch to make sure the both temperatures are within the specification. If even one of them is out of the specifications,please adjust. (Normal condition) 90±30 40±10 Time ● Carrier tape F E H φG J I K A C B D t Take out direction Taping condition : Lack of products in the middle of taping should be one MAX. but total quantity specified in the specifications should be secured. Peeling off strength of top tape : It should be within 0.2N to 1.0N at 165 degree in peeling off angle. Joint of carrier tape : One joint per one reel may exist. Unit: mm Part No. EVPBL Height 0.53 0.57 0.60 A B C D E F G H I J K t 8.0±0.3 1.75±0.1 3.5±0.1 4.0±0.1 4.0±0.1 2.0±0.1 1.5 ー0 2.2±0.2 3.4±0.2 0.7±0.2 (6.25) 0.3±0.1 ＋0.1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Panasonic Corporation Electromechanical Control Business Division industrial.panasonic.com/ac/e/ 3 © Panasonic Corporation 2020 ANCTB104E 202002 Requests to customers Please refer to "the latest product specifications" when designing your product. Requests to customers : https://industrial.panasonic.com/ac/e/salespolicies/ Safety Precautions When using our products, no matter what sort of equipment they might be used for, be sure to confirm the applications and environmental conditions with our specifications in advance. Please contact .......... Electromechanical Control Business Division 1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8506, Japan industrial.panasonic.com/ac/e/ ©Panasonic Corporation 2020 ANCTB104E 202002 Specifications are subject to change without notice.