UPC4744GR-9LG-E2-A

DATA SHEET BIPOLAR ANALOG INTEGRATED CIRCUIT μ PC844GR-9LG, μ PC4744GR-9LG SINGLE POWER SUPPLY, HIGH SPEED, WIDE BAND, QUAD OPERATIONAL AMPLIFIERS DESCRIPTION The μ PC844GR-9LG, μ PC4744GR-9LG are a high speed version of the operational amplifier μ PC451GR-9LG, μ PC324GR-9LG for general single power supply use with high speed pulse response and high stabilization. A high speed PNP transistor is used in the circuit which improves the characteristics such as a slew rate, gain-bandwidth product, stabilization of the withstand load capacitance, with no crossover distortion compared to μ PC451GR-9LG, μ PC324GR-9LG. Therefore, μ PC844GR-9LG, μ PC4744GR-9LG can be used in a wide range of application circuits for single power supply AC amplifier, active filters, line driver and an amplifier for light receiving element etc. The μ PC844GR-9LG which expands temperature type is suited for wide operating ambient temperature use, and μ PC4744GR-9LG is used for general purposes. μ PC842GR-9LG, μ PC4742GR-9LG which are dual types with the same circuit configuration are also available as series of operational amplifiers. FEATURES • Slew Rate (AV = +1) (V+ = +5 V, V− = GND) • Gain Band Width Product • Input Offset Voltage • Input Offset Current 3.5 MHz (TYP.) ±2 mV (TYP.) ±6 nA (TYP.) 7 V/μs (TYP.) • Stability to capacitive loads (load capacity, 1000 pF) • Internal frequency compensation • Output short-circuit protection • A pin connection (pin compatible) of a standard quad operational amplifier. • Wide operating ambient temperature range μ PC844GR-9LG: TA = −40 to +125°C, μ PC4744GR-9LG: TA = −40 to +85°C • Small Package (The mounting area is reduced to half compared to the conventional 14-pin plastic SOP (1.27 mm pitch)) ORDERING INFORMATION Part Number Selected Grade Note Package 14-pin plastic TSSOP (5.72 mm(225)) 14-pin plastic TSSOP (5.72 mm(225)) 14-pin plastic TSSOP(5.72 mm(225)) 14-pin plastic TSSOP(5.72 mm(225)) Package Type • 16 mm wide embossed taping • Pin 1 on draw-out side • 16 mm wide embossed taping • Pin 1 at take-up side • 16 mm wide embossed taping • Pin 1 on draw-out side • 16 mm wide embossed taping • Pin 1 at take-up side μ PC844GR-9LG-E1-A μ PC844GR-9LG-E2-A Standard Standard Standard Standard Note μ PC4744GR-9LG-E1-A μ PC4744GR-9LG-E2-A Note Note Note Pb-free (This product does not contain Pb in the external electrode and other parts.) The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. Document No. G17928EJ4V0DS00 (4th edition) Date Published December 2007 NS Printed in Japan 2006, 2007 The mark shows major revised points. The revised points can be easily searched by copying an "" in the PDF file and specifying it in the "Find what:" field. μ PC844GR-9LG, μ PC4744GR-9LG EQUIVALENT CIRCUIT (1/4 Circuit) V+ Q7 Q8 Q9 Q10 Q11 Q12 PIN CONFIGURATION (Marking side) OUT1 II1 IN1 Q2 Q3 Q4 Q18 Q19 1 2 3 4 5 6 7 −+ 2 +− 3 1 −+ 4 +− 14 13 12 11 10 9 8 OUT4 II4 IN4 V− IN3 II3 OUT3 V + II IN Q1 IN2 OUT Q14 Q20 II2 OUT2 Q5 Q6 Q13 Q15 Q16 Q17 V− ABSOLUTE MAXIMUM RATINGS (TA = 25°C) Parameter Voltage between V and V Differential Input Voltage Input Voltage Note2 Note3 Note4 Note5 Symbol V −V VID VI VO PT tS TA Tstg + − μ PC844GR-9LG −0.3 to +36 ±36 − − μ PC4744GR-9LG Unit V V V V mW s + − Note1 V − 0.3 to V + 36 V − 0.3 to V + 0.3 550 Indefinite −40 to +125 −55 to +150 −40 to +85 −55 to +125 + − + Output applied Voltage Total Power Dissipation Output Short Circuit Duration Operating Ambient Temperature Storage Temperature °C °C Note1. Note that reverse connections of the power supply may damage ICs. 2. The input voltage is allowed to input without damage or destruction independent of the magnitude of V . Either input signal is not allowed to go negative by more than 0.3 V. In addition, the input voltage that operates normally as an operational amplifier is within the Common Mode Input Voltage range of an electrical characteristic. 3. A range where input voltage can be applied to an output pin externally with no deterioration or damage to the feature (characteristic). The input voltage can be applied regardless of the electric supply voltage. This specification which includes the transition state such as electric power ON/OFF must be kept. 4. This is the value of when the glass epoxy substrate (size: 100 mm x 100 mm, thickness: 1 mm, 15% of the substrate area where only one side is copper foiled is filling wired) is mounted. Note that restrictions will be made to the following conditions for each product, and the derating ratio depending on the operating ambient temperature. μ PC844GR-9LG: Derate at −7.0 mW/°C when TA > 71°C. (Junction − ambient thermal resistance Rth(J-A) = 144°C/W) μ PC4744GR-9LG: Derate at −7.0 mW/°C when TA > 46°C. (Junction − ambient thermal resistance Rth(J-A) = 144°C/W) 5. Pay careful attention to the total power dissipation not to exceed the absolute maximum ratings, Note 4. 2 Data Sheet G17928EJ4V0DS μ PC844GR-9LG, μ PC4744GR-9LG RECOMMENDED OPERATING CONDITIONS Parameter Power Supply Voltage (Split) Power Supply Voltage (V = GND) Output Current Capacitive Load (AV = +1) − Symbol V V ± + MIN. ±1.5 +3 TYP. MAX. ±16 Unit V V mA pF +5 to +30 +32 ±10 1000 Note IO CL Note This is the value during a feedback resistance (Rf) = 0 Ω. ELECTRICAL CHARACTERISTICS TA = 25°C, V± = ±15 V Parameter Input Offset Voltage Input Offset Current Input Bias Current Note1 Symbol VIO IIO IB AV ICC CMR SVR VOm1 RL = 10 kΩ Conditions MIN. TYP. ±2 ±6 130 MAX. ±6 ±75 500 Unit mV nA nA Large Signal Voltage Gain Circuit Current Note2 RL ≥ 2 kΩ, VO = ±10 V IO = 0 A 25000 300000 7.5 11 mA dB dB V V V − 1.8 8.5 3.5 120 + Common Mode Rejection Ratio Supply Voltage Rejection Ratio Output Voltage Swing 70 70 ±13.7 ±13.5 V AV = +1 (rise) f = 100 kHz f = 20 Hz to 20 kHz − 86 93 +14 −14.3 VOm2 Common Mode lnput Voltage Range Slew Late Gain Band Width Product Channel Separation VICM SR GBW RL ≥ 2 kΩ V V/μs MHz dB TA = 25°C, V+ = +5 V, V− = GND Parameter Input Offset Voltage Input Offset Current Input Bias Current Note1 Symbol VIO IIO IB AV ICC CMR SVR VOm RL ≥ 2 kΩ IO = 0 A Conditions MIN. TYP. ±2 ±6 150 MAX. ±5 ±75 500 Unit mV nA nA Large Signal Voltage Gain Circuit Current Note2 25000 300000 6 9 mA dB dB V V − 1.8 30 30 7 + Common Mode Rejection Ratio Supply Voltage Rejection Ratio Output Voltage Swing 70 70 RL ≥ 2 kΩ (Connect to GND) 3.7 0 80 95 4 0 Common Mode lnput Voltage Range Output Source Current Output Sink Current Slew Late VICM IO SOURCE IO SINK SR VIN (+) = +1 V, VIN (−) = 0 V VIN (+) = 0 V, VIN (−) = +1 V AV = +1 (rise) 0 10 10 V mA mA V/μs Notes1. The input bias current flows in the direction where the IC flows out because the first stage is configured with a PNP transistor. 2. This is a current that flows in the internal circuit. This current will flow irrespective of the channel used. Data Sheet G17928EJ4V0DS 3 μ PC844GR-9LG, μ PC4744GR-9LG TYPICAL PERFORMANCE CHARACTERISTICS (TA = 25°C, TYP.) (Reference value) PT vs. TA ICC vs. V+ 16 V+ A ICC 1000 PT - Total Power Dissipation - mW 800 600 ICC - Supply Current - mA With 100 mm x 100 mm, thickness 1 mm glass epoxy substrate (refer to "ABSOLUTE MAXIMUM RATINGS Note 4" ) IO = 0 A TA = −40°C 25°C 12 1V − + μP 400 200 0 0 20 40 C4 μP 74 4G R- C8 8 44 GR 9L -9 G LG 4 125°C 0 60 80 100 120 140 0 10 20 30 40 TA - Operating Ambient Temperature - °C V+ - Power Supply Voltage - V (V− = GND) VIO vs. V+ 2 VIO - Input Offset Voltage - mV VIO - Input Offset Voltage - mV 4 3 2 1 0 -1 -2 -3 -4 0 + VIO vs. TA 1 0 -1 V± = ±15 V each 5 samples date -50 0 50 100 150 -2 10 20 30 − 40 V - Power Supply Voltage - V (V = GND) TA - Operating Ambient Temperature - °C VICM vs. V+ VICM - Common Mode Input Voltage Range - V IB vs. V+ 200 40 IB - Input Bias Current - nA 30 VICM + 20 150 100 10 VICM − 50 VIN = V+/2 0 0 0 + 10 20 30 − 40 0 + 10 20 30 − 40 V - Power Supply Voltage - V (V = GND) V - Power Supply Voltage - V (V = GND) 4 Data Sheet G17928EJ4V0DS μ PC844GR-9LG, μ PC4744GR-9LG IB vs. TA 200 VO - Output Voltage Signal - Vp-p 30 VO vs. f V± = ±15 V RL = 2 k Ω 20 IB - Input Bias Current - nA 150 100 10 50 V± = ±15 V 0 -50 0 50 100 150 TA - Operating Ambient Temperature - °C 0 1 10 100 f - Frequency - Hz AV, φ vs. f 1k 10 k 120 AV - Voltage Gain - dB, φ - Phase Margin - deg. V± = ±2.5 V 100 AV ±15 V 80 ±2.5 V 60 φ ±15 V 40 20 0 0.1 1 10 100 1k 10 k 100 k 1M 10 M f - Frequency - Hz PULSE RESPONSE VIN - Input Voltage - V VO - Output Voltage - V 15 SR - TA 3 2 1 0 3 2 1 0 SR - Slew Rate - V/μs RL = 2 kΩ V+ = +5 V V− = GND Fall 12 9 Rise 6 3 0 V± = ±15 V RL = 2 k Ω -50 0 50 100 150 0 1 2 3 t - time - μs TA - Operating Ambient Temperature - °C Data Sheet G17928EJ4V0DS 5 μ PC844GR-9LG, μ PC4744GR-9LG VO vs. IO SINK 10 V+ V+ /2 − + IO SINK VO ΔVO vs. IO SOURCE 5 V+ ΔVO - Output Voltage to V+ - V V = +15 V + V+ = +15 V ΔVO VO - Output Voltage - V 4 3 2 1 V+ /2 + − TA = −40°C 1 IO SOURCE TA = −40°C 25°C 125°C 125°C 0.1 0.01 25°C 0.1 1 10 100 0 0.01 0.1 1 10 100 IO SINK - Output Sink Current - mA IO SOURCE - Output Source Current - mA 6 Data Sheet G17928EJ4V0DS μ PC844GR-9LG, μ PC4744GR-9LG PRECAUTIONS FOR USE O The process of unused circuits If there is an unused circuit, the following connection is recommended. Process example of unused circuits V+ V+ R − + R V− To potentials within the range of common-mode input voltage (VICM) V− Remark A midpoint potential of V+ and V− is applied to this example. O Ratings of input/output pin voltage When the voltage of input/output pin exceeds the absolute maximum rating, it may cause degradation of characteristics or damages, by a conduction of a parasitic diode within an IC. In addition, when the input pin may be lower than V−, or the output pin may exceed the power supply voltage, it is recommended to make a clump circuit by a diode whose forward voltage is low (e.g.: Schottky diode) for protection. O Range of common-mode input voltage When the supply voltage does not meet the condition of electrical characteristics, the range of common-mode input voltage is as follows. VICM (TYP.): V− to V+ − 1.8 (V) (TA = 25°C) During designing, temperature characteristics for use with allowance. O The maximum output voltage The range of the TYP. value of the maximum output voltage when the supply voltage does not meet the condition of electrical characteristics is as follows: VOm+ (TYP.): V+ − 1 (V) (TA = 25°C), VOm− (TYP.): V− + 0.7 (V) (TA = 25°C) During designing, consider variations in characteristics and temperature characteristics for use with allowance. In addition, also note that the output voltage range (VOm+ − VOm−) becomes narrow when an output current increases. O Operation of output This IC will not operate an output current sinking when the output voltage is V− + 0.7 V and below. In this situation, an output voltage and its level approach to the V− side can be improved by connecting the load resistance to an output pin / V− intermediate by sinking current at the load resistance side. (The effect will differ depending on the flow of current in the load resistance.) O Handling of ICs When stress is added to ICs due to warpage or bending of a board, the characteristic fluctuates due to piezoelectric effect. Therefore, pay attention to warpage or bending of a board. Data Sheet G17928EJ4V0DS 7 μ PC844GR-9LG, μ PC4744GR-9LG PACKAGE DRAWINGS (Unit: mm) 14-PIN PLASTIC TSSOP (5.72mm (225)) D D1 detail of lead end A3 14 8 c θ 1 7 L Lp (UNIT:mm) ZD b x M e S ITEM D D1 E HE DIMENSIONS 5.15 ± 0.15 5.00 ± 0.10 4.40 ± 0.10 6.40 ± 0.20 1.20 MAX. 0.10 ± 0.05 1.00 ± 0.05 0.25 + 0.06 0.24 − 0.05 0.145 ± 0.055 0.50 0.60 ± 0.15 1.00 ± 0.20 3° +5° −3° 0.65 0.10 0.10 0.625 P14GR-65-9LG HE A A2 S E L1 A A1 A2 A3 b c L Lp L1 y S A1 θ NOTE Each lead centerline is located within 0.10mm of its true position at maximum material condition. e x y ZD 8 Data Sheet G17928EJ4V0DS μ PC844GR-9LG, μ PC4744GR-9LG RECOMMENDED SOLDERING CONDITIONS The μ PC844GR-9LG, μ PC4744GR-9LG should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact an NEC Electronics sales representative. For technical information, see the following website. Semiconductor Device Mount Manual (http://www.necel.com/pkg/en/mount/index.html) Type of Surface Mount Device μ PC844GR-9LG-A Process Infrared ray reflow Note , μ PC4744GR-9LG-A Note : 14-pin plastic TSSOP (5.72 mm (225)) Conditions Symbol IR60-00-3 Peak temperature: 260°C, Reflow time: 60 seconds or less (at 220°C or higher), Maximum number of reflow processes: 3 times. Wave soldering Solder temperature: 260°C or below, Flow time: 10 seconds or less, Maximum number of flow processes: 1 time, Pre-heating temperature: 120°C or below (Package surface temperature). WS60-00-1 Partial heating method Pin temperature: 350°C or below, Heat time: 3 seconds or less (Per each side of the device). P350 Note Pb-free (This product does not contain Pb in external electrode and other parts.) Caution Apply only one kind of soldering condition to a device, except for “partial heating method”, or the device will be damaged by heat stress. Remark Flux: Rosin flux with low chlorine (0.2 Wt% or below) recommended. REFERENCE DOCUMENTS Document Name QUALITY GRADES ON NEC SEMICONDUCTOR DEVICES SEMICONDUCTOR DEVICE MOUNT MANUAL NEC SEMICONDUCTOR DEVICE RELIABILITY/QUALITY CONTROL SYSTEM-STANDARD LINEAR IC REVIEW OF QUALITY AND RELIABILITY HANDBOOK NEC SEMICONDUCTOR DEVICE RELIBIALITY/QUALITY CONTROL SYSTEM C12769E C10983E C11531E http://www.necel.com/pkg/en/mount/index.html IEI-1212 Document No. Data Sheet G17928EJ4V0DS 9 μ PC844GR-9LG, μ PC4744GR-9LG • T he information in this document is current as of December, 2007. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. • NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. • NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above). M8E 02. 11-1