UPG2179TB-E4-A

NEC's 1.5W UPG2179TB L, S-BAND SPDT SWITCH FEATURES • SWITCH CONTROL VOLTAGE: Vcont (H) = 2.5 to 5.3 V (3.0 V TYP.) Vcont (L) = −0.2 to +0.2 V (0 V TYP.) • LOW INSERTION LOSS: 0.25 dB TYP. @ 0.5 to 1.0 GHz, Vcont = 3.0 V/0 V 0.30 dB TYP. @ 1.0 to 2.0 GHz, Vcont = 3.0 V/0 V 0.35 dB TYP. @ 2.0 to 2.5 GHz, Vcont = 3.0 V/0 V 0.40 dB TYP. @ 2.0 to 3.0 GHz, Vcont = 3.0 V/0 V • HIGH ISOLATION: 27 dB TYP. @ 0.5 to 2.0 GHz, Vcont = 3.0 V/0 V 24 dB TYP. @ 2.0 to 2.5 GHz, Vcont = 3.0 V/0 V • HIGH POWER: Pin (0.1 dB) = +29.0 dBm TYP. @ 0.5 to 3.0 GHz, Vcont = 3.0 V/0 V Pin (1 dB) = +32.0 dBm TYP. @ 0.5 to 3.0 GHz, Vcont = 3.0 V/0 V • HIGH-DENSITY SURFACE MOUNT PACKAGE: 6-pin super minimold package (2.0 × 1.25 × 0.9 mm) • PB-FREE DESCRIPTION NEC's UPG2179TB is a GaAs MMIC L, S-band SPDT (Single Pole Double Throw) switch for mobile phone and L, S-band applications from 0.5 to 3.0 GHz. This device can operate with 2.5 to 5.3 V from 50 MHz to 3 GHz with low insertion loss and high isolation. The UPG2179TB is housed in a Pb-Free 6-pin super minimold package suitable for high-density surface mounting. APPLICATIONS • L, S-band digital cellular and cordless telephones • PCS, W-LAN, WLL and BluetoothTM • Short Range Wireless ORDERING INFORMATION PART NUMBER UPG2179TB-E4-A PACKAGE 6-pin super minimold MARKING G4C SUPPLYING FORM • Embossed tape 8 mm wide • Pin 4, 5, 6 face the perforation side of the tape • Qty 3 kpcs/reel Remark To order evaluation samples, contact your nearby sales ofÞce. Part number for sample order: UPG2179TB-A Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. California Eastern Laboratories UPG2179TB PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM (Top View) 1 61 (Top View) 66 (Bottom View) 1 Pin No. 1 2 3 Pin Name OUTPUT1 GND OUTPUT2 Vcont2 INPUT Vcont1 G4C VCONT1 Low High High Low PARAMETER PARAMETER 2 52 55 2 4 5 3 43 44 3 6 TRUTH TABLE VCONT2 INPUT−OUTPUT1 ON OFF INPU−OUTPUT2 OFF ON ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise speciÞed) SYMBOL Vcont Pin TA Tstg RATINGS 6.0 +33 −45 to +85 −55 to +150 UNIT V dBm °C °C Switch Control Voltage Input Power Operating Ambient Temperature Storage Temperature Note |Vcont1 – Vcont2| ≤ 6.0 V RECOMMENDED OPERATING RANGE (TA = 25°C, unless otherwise speciÞed) SYMBOL Vcont (H) Vcont (L) MIN. 2.5 −0.2 TYP. 3.0 0 MAX. 5.3 0.2 UNIT V V Switch Control Voltage (H) Switch Control Voltage (L) UPG2179TB ELECTRICAL CHARACTERISTICS (TA = +25°C, Vcont = 3.0 V/0V, DC blocking capacitors = 100 pF, unless otherwise speciÞed) PARAMETER Insertion Loss 1 Insertion Loss 2 Insertion Loss 3 Insertion Loss 4 Isolation 1 Isolation 2 Input Return Loss Output Return Loss 0.1 dB Loss Compression Input Power Note2 Icont tSW SYMBOL LINS1 LINS2 LINS3 LINS4 ISL1 ISL2 RLin RLout Pin (0.1 dB) TEST CONDITIONS f = 0.5 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.5 to 2.0 GHz f = 2.0 to 3.0 GHz f = 0.5 to 3.0 GHz f = 0.5 to 3.0 GHz f = 2.0 GHz f = 2.5 GHz f = 0.5 to 3.0 GHz Switch Control Current Switch Control Speed No signal 50%CTL to 90/10%RF Note1 Note1 Note1 Note1 MIN. − − − − 23 20 15 15 +25.5 +25.5 − − − TYP. 0.25 0.30 0.35 0.40 27 24 20 20 +29.0 +29.0 +29.0 4 50 MAX. 0.45 0.50 0.55 0.60 − − − − − − − 20 500 UNIT dB dB dB dB dB dB dB dB dBm dBm dBm μA ns Note 1. DC blocking capacitor = 1 000pF at f = 0.05 to 0.5 GHz. 2. Pin(0.1 dB) is the measured input power level when the insertion loss increases 0.1 dB more than that of linear range. STANDARD CHARACTERISTICS FOR REFERENCE (TA = +25°C, Vcont = 3.0 V/0 V, DC blocking capacitors = 100 pF, unless otherwise speciÞed) PARAMETER 1 dB Loss Compression Input Power Note IIP3 f = 0.5 to 3.0 GHz, 2 tone, 5 MHz spacing − +60.0 − dBm SYMBOL Pin (1 dB) TEST CONDITIONS f = 0.5 to 3.0 GHz MIN. − TYP. +32.0 MAX. − UNIT dBm 3rd Order Intermodulation Intercept Point Note Pin (1 dB) is the measured input power level when the insertion loss increases 1 dB more than that of linear range. Caution It is necessary to use DC blocking capacitors with this device. The value of DC blocking capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with the actual board of your system. The range of recommended DC blocking capacitor value is less than 100 pF for frequencies above 0.5 GHz, and 1,000 pF for frequencies below 0.5 GHz. UPG2179TB EVALUATION CIRCUIT (Vcont1 = 3.0 V, Vcont2 = 0 V or Vcont2 = 0 V, Vcont1 = 3.0 V, off chip DC blocking capacitors value C1 = 51 pF, C2 = 1 000 pF (Bypass), using NEC standard evaluation board) OUTPUT2 OUTPUT1 56 pF 56 pF 3 2 1 4 5 6 1 000 pF 56 pF 1 000 pF Vcont2 INPUT Vcont1 This application circuits and their parameters are for reference only and are not intended for use in actual design-ins. UPG2179TB ILLUSTRATION OF TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD Vcont2 6pin SMM SPDT SW Vc2 OUTPUT2 OUT 2 C2 C 2 C 4 C1 INPUT C1 IN C 5 C3 G4C C1 C 1 C2 OUT 1 OUTPUT1 Vc1 Vcont1 USING THE NEC EVALUATION BOARD SYMBOL C1, C2, C3 C4, C5 VALUES 100 pF 1 000 pF UPG2179TB TYPICAL CHARACTERISTICS (TA = +25°C, Vcont = 3.0 V/0 V, DC blocking capacitors = 100 pF, unless otherwise speciÞed) INPUT-OUTPUT1 INSERTION LOSS vs. FREQUENCY 0.5 0.4 Insertion Loss LINS (dB) Insertion Loss LINS (dB) 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 Frequency f (GHz) 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 INPUT-OUTPUT2 INSERTION LOSS vs. FREQUENCY -0.5 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 Frequency f (GHz) INPUT-OUTPUT1 ISOLATION vs. FREQUENCY 50 40 30 Isolation ISL (dB) 20 10 0 -10 -20 -30 -40 -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 Frequency f (GHz) Isolation ISL (dB) 50 40 30 20 10 0 -10 -20 -30 -40 INPUT-OUTPUT2 ISOLATION vs. FREQUENCY -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 Frequency f (GHz) INPUT-OUTPUT1 INPUT RETURN LOSS vs. FREQUENCY 50 40 Input Return Loss RLin (dB) 30 20 10 0 -10 -20 -30 -40 -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 Frequency f (GHz) Input Return Loss RLin (dB) INPUT-OUTPUT2 INPUT RETURN LOSS vs. FREQUENCY 50 40 30 20 10 0 -10 -20 -30 -40 -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 Frequency f (GHz) Remark The graphs indicate nominal characteristics. UPG2179TB INPUT-OUTPUT1 OUTPUT RETURN LOSS vs. FREQUENCY 50 Output Return Loss RLout (dB) Output Return Loss RLout (dB) Frequency f (GHz) 40 30 20 10 0 -10 -20 -30 -40 -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 INPUT-OUTPUT2 OUTPUT RETURN LOSS vs. FREQUENCY 50 40 30 20 10 0 -10 -20 -30 -40 -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 Frequency f (GHz) OUTPUT POWER vs. INPUT POWER 33 31 Output Power Pout (dBm) 29 27 25 23 21 19 17 15 13 15 17 19 21 23 25 27 29 31 33 35 f = 1.0 GHz Output Power Pout (dBm) 33 31 29 27 25 23 21 19 17 15 OUTPUT POWER vs. INPUT POWER f = 2.5 GHz 13 15 14 19 21 23 25 27 29 31 33 35 Input Power Pin (dBm) Input Power Pin (dBm) Remark The graphs indicate nominal characteristics. UPG2179TB PACKAGE DIMENSIONS 6-PIN SUPER MINIMOLD (UNIT: mm) 2.1±0.1 1.25±0.1 2.0±0.2 1.3 0.65 0.65 0.1 MIN. 0.9±0.1 0.7 0 to 0.1 0.15+0.1 -0.05 0.2+0.1 -0.05 UPG2179TB RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales ofÞce. Soldering Method Infrared Reßow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220°C or higher Preheating time at 120 to 180°C Maximum number of reßow processes Maximum chlorine content of rosin ßux (% mass) Peak temperature (package surface temperature) Time at temperature of 200°C or higher Preheating time at 120 to 150°C Maximum number of reßow processes Maximum chlorine content of rosin ßux (% mass) Peak temperature (molten solder temperature) Time at peak temperature : 260°C or below : 10 seconds or less : 60 seconds or less : 120±30 seconds : 3 times : 0.2%(Wt.) or below : 215°C or below : 25 to 40 seconds : 30 to 60 seconds : 3 times : 0.2%(Wt.) or below : 260°C or below : 10 seconds or less Condition Symbol IR260 VPS VP215 Wave Soldering WS260 Preheating temperature (package surface temperature) : 120°C or below Maximum number of ßow processes : 1 time Maximum chlorine content of rosin ßux (% mass) : 0.2%(Wt.) or below Partial Heating Peak temperature (pin temperature) Soldering time (per side of device) Maximum chlorine content of rosin ßux (% mass) : 350°C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 Caution Do not use different soldering methods together (except for partial heating). Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. 06/01/2004 A Business Partner of NEC Compound Semiconductor Devices, Ltd. 5-148