ULR2D330MNL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS ULR Chip Type, High Voltage. Chip Type, high Voltage. Applicable to automatic mounting machine using carrier tape. Compliant to the RoHS directive (2011/65/EU). AEC-Q200 compliant. Please contact us for details. ULV ULR Long Life High Voltage UUX Specifications Item Performance Characteristics Category Temperature Range –40 to +105°C Rated Voltage Range 160 to 500V Rated Capacitance Range 2.7 to 39µF Capacitance Tolerance Leakage Current ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.04CV +100(µA). Tangent of loss angle (tan δ) Rated voltage (V) tan δ (MAX.) Measurement frequency : 120Hz at 20°C 160 0.20 200 0.20 250 0.25 400 0.25 450 0.30 500 0.30 Measurement frequency: 120Hz Stability at Low Temperature Rated voltage (V) Impedance ratio ZT / Z20 (MAX.) 160 200 250 400 450 500 6 6 10 10 15 15 Z–40°C / Z+20°C Capacitance change tan δ Leakage current Within ±20% of the initial capacitance value 200% or less than the intial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 3000 hours at 105°C. Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the characteristic requirements listed at right when they are removed from the plate. Resistance to soldering heat Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Black print on the case top. Marking Chip Type Type numbering system (Example : 400V 8.2µF) (φ8 , φ10) Capacitance 3 4 5 6 7 8 9 10 11 12 13 14 Taping code A±0.2 E A±0.2 B±0.2 φD±0.5 A2 8.2 2G LR Lot No. 2 U L R 2 G 8 R 2 MN L 1 GS 0.5MAX. C±0.2 0.3MAX. Series 1 Positive Plastic platform Voltage(2G : 400V) Trade mark Capacitance change tan δ Leakage current Rated capacitance (8.2µF) H L±1.0 Configuration Capacitance tolerance (±20%) Negative Rated voltage (400V) Pressure relief vent (mm) φD × L A B C E L H 8 × 10 10 × 10 2.9 3.2 8.3 10.3 8.3 10.3 3.1 4.5 10 10 0.8 to 1.1 0.8 to 1.1 Series name 10 × 13.5 3.2 10.3 10.3 4.5 13.5 0.8 to 1.1 Type Voltage V Code 160 200 250 400 450 500 2C 2D 2E 2G 2W 2H Dimensions Cap.(µF) 2.7 3.9 4.7 5.6 6.8 8.2 10 12 15 22 27 33 39 160 2C V Code 2R7 3R9 4R7 5R6 6R8 8R2 100 120 150 220 270 330 390 200 2D 8 × 10 50 10 × 10 65 10 × 13.5 70 250 2E 8 × 10 50 10 × 10 65 10 × 13.5 70 400 2G 8 × 10 35 10 × 10 10 × 13.5 50 55 450 2W 8 × 10 35 10 × 10 50 10 × 13.5 55 500 2H 8 × 10 25 10 × 10 40 10 × 13.5 45 8 × 10 10 × 10 20 35 10 × 13.5 40 Case size φ D × L (mm) Rated ripple Rated ripple current (mArms) at 105°C 120Hz Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.80 120 Hz 1.00 300 Hz 1.25 1 kHz 1.40 10 kHz or more 1.60 160 CAT.8100H