FTAS00-84AS4

Toggles Series FT 4-Wire Touch Screens with Printed Tails Rockers General Specifications Electrical Capacity (Resistive Load) Power Level: 1mA @ 5V DC (resistive load) Pushbuttons Other Ratings XY Resistive Value: Linearity: Insulation Impedance: Expected Operational Life: Programmable Illuminated PB Environmental Data Keylocks 250 ~ 850Ω; Wide: 120 ~ 1,500Ω ±1.5% maximum 10MΩ minimum @ 25V DC Writing: 50,000 operations minimum (approximately 30mm movement with stylus) Tapping: 1,000,000 operations minimum (pressing force 4.9N using silicone rubber, hardness 60°) 1.47N maximum 10 milliseconds maximum 80% typical (Touch Panel portion) 2H minimum (JIS K5600) Operating Temperature Range: –20°C ~ +70°C (–4°F ~ +158°F) Storage Temperature Range: –40°C ~ +80°C (–40°F ~ +176°F) Relative Humidity: +60°C (+140°F), humidity 90%, 240 hours Rotaries Touch Activation Force: Chattering Time: Light Transmission: Surface Hardness: TYPICAL ORDERING EXAMPLE Slides FT AS 00 12.1 A N 4 Number of Keys Tactiles 00 Type Analog 4 Input Method A Finger or Stylus Screen Size 5.7” 6.5 6.5” 8.4 8.4” No Code Left or Right (Horizontal) 10.4 10.4” V Top or Bottom (Vertical) 10.6 10.6” 12.1 12.1” S Narrow Frame Type 1 (Horizontal) N Narrow Frame Type 2 (Horizontal) W Wide Type (Horizontal) Tilt Touch Indicators DESCRIPTION FOR TYPICAL ORDERING EXAMPLE 5.7 15 15.0” 15.6 15.6” 19 19.0” FTAS00–12.1AN–4 *Position of Tail (Analog) * Aspect Ratio: Narrow Frame: 4:3 Wide Frame: 16:9 Narrow Frame Type 2 Horizontal Tail Position Touch Screen with 12.1" Screen Supplement Accessories L Finger or Stylus Input L10 4-Wire 4-Wire Analog www.nkkswitches.com 6/15/18 Series FT Toggles 4-Wire Touch Screens with Printed Tails FTAS00-8.4AS-4 FTAS00-10.4AS-4 FTAS00-10.4AV-4 FTAS00-10.6AW-4 FTAS00-12.1AN-4 FTAS00-12.1AW-4 Programmable Illuminated PB FTAS00-6.5AS-4 Keylocks FTAS00-5.7AS-4 Pushbuttons Rockers PART NUMBERS & DESCRIPTIONS Rotaries FTAS00-19AN-4 4-Wire Analog Touch Screens Wide Type Horizontal Tail Screen Size in Inches Key Area Dimensions Viewing Area Dimensions External Dimensions FTAS00-5.7AS-4 5.7 4.54” x 3.40” (115.2mm x 86.4mm) 4.76” x 3.61” (121.0mm x 91.6mm) 5.16” x 3.98” (131.0mm x 101.0mm) FTAS00-6.5AS-4 6.5 5.20” x 3.90” (132.0mm x 99.0mm) 5.43” x 4.13” (138.0mm x 105.0mm) 5.91” x 4.57” (150.0mm x 116.0mm) FTAS00-8.4AS-4 8.4 6.73” x 5.10” (170.9mm x 129.6mm) 6.95” x 5.33” (176.5mm x 135.4mm) 7.34” x 5.69” (186.5mm x 144.4mm) Length 3.150” (80.0mm) FTAS00-10.4AS-4 10.4 8.32” x 6.24” (211.2mm x 158.4mm) 8.47” x 6.39” (215.0mm x 162.4mm) 8.88” x 6.75” (225.6mm x 171.4mm) Length 3.150” (80.0mm) FTAS00-10.4AV-4 10.4 8.35” x 6.28” (212.2mm x 159.4mm) 8.52” x 6.43” (216.4mm x 163.4mm) 8.92” x 7.20” (226.5mm x 183.0mm) Length 3.150” (80.0mm) FTAS00-12.1AN-4 12.1 9.677” x 7.256” (245.8mm x 184.3mm) 9.827” x 7.406” (249.6mm x 188.1mm) 10.236” x 7.795” (260.0mm x 198.0mm) Length 3.150” (80.0mm) FTAS00-15AN-4 15.0 11.972” x 8.980” (304.1mm x 228.1mm) 12.130” x 9.138” (308.1mm x 232.1mm) 12.669” x 9.665” (321.8mm x 245.5mm) FTAS00-19AN-4 19.0 14.815” x 11.850” (376.3mm x 301.0mm) 15.039” x 12.102” (382.0mm x 307.4mm) 15. 571” x 12.638” (395.5mm x 321.0mm) Length 3.150” (80.0mm) FTAS00-10.6AW-4 10.6 9.071” x 5.441” (230.4mm x 138.2mm) 9.189” x 5.563” (233.4mm x 141.3mm) 9.756” x 6.094” (247.8mm x 154.8mm) Length 3.150” (80.0mm) FTAS00-12.1AW-4 12.1 10.280” x 6.425” 10.404” x 6.551” 10.827” x 6.929” (261.12mm x 163.2mm) (264.26mm x 166.4mm) (275.0mm x 176.0mm) Length 3.150” (80.0mm) FTAS00-15.6AW-4 15.6 13.551” x 7.618” (344.2mm x 193.5mm) Note: For other sizes or frame types, contact the factory. 13.681” x 7.748” (347.5mm x 196.8mm) 14.276” x 8.433” (362.6mm x 214.2mm) .083” (2.1mm) Length 2.559” (65.0mm) Length 3.150” (80.0mm) Length 3.150” (80.0mm) * 4 pin available with 1.0mm or 1.25mm pitch. Contact factory for details. www.nkkswitches.com Tactiles Length 2.559” (65.0mm) L11 Tilt .055” (1.4mm) L Touch Panel Thickness Slides * Terminal Detail 8 Pin .049” (1.25mm) Pitch Part Number Indicators Narrow Frame Type 2 Vertical Horizontal Tail Tail Narrow Frame Type 1 Horizontal Tail Tail Accessories FTAS00-15.6AW-4 Supplement FTAS00-15AN-4 Toggles Series FT 4-Wire Touch Screens with Printed Tails TYPICAL DIMENSIONS A Pushbuttons Rockers Horizontal Tail & Narrow Frame Type 2 (1.5) Air Vent .059 (80.0) ±1.0 3.15 (70.0) 2.76 YUP (60.0) 2.36 (10.0) .394 H D Pin 1 Programmable Illuminated PB (11.25) ±0.1 .443 (0.8) Typ .031 F Center of Active Area Pin 8 (28.2) 1.11 Reinforcement Film 16 x 24 (0.5) .020 E XRI X LE (1.25) Typ (5.0) .049 .197 B Viewable Area C Active Area Y LO G Center of Active Area (55.0) 2.17 Keylocks Tail Dimensions for (10.0) .394 Rotaries FTAS00-5.7AS-4 FTAS00-6.5AS-4 (65.0) ±1.0 2.56 (45.0) 1.77 Pin 1 Pin 8 Slides Contact Side (0.3) ±0.05 .012 Stiffener Top Electrode Insulation Film Tail Reinforcement Film Tactiles YUP 1 XLE X RI Tilt 8 Bottom Electrode Pins Signal 1, 2 YUP 3, 4 YLO YLO 5, 6 XLE XLE, XRI: Top Electrode Terminal YUP, YLO: Bottom Electrode Terminal 7, 8 XRI J Supplement Accessories Indicators Touch 4-Wire Analog Touch Screen Dimensions L Part Number FTAS00-5.7AS-4 5.7 5.16” 4.76” 4.54” 3.40” (131.0±0.3mm) (121.0mm) (115.2mm) (86.4mm) 3.61” 3.98” (91.6mm) (101.0±0.3mm) 2.65” (67.25mm) 1.99” (50.5mm) .055” (1.4mm) FTAS00-6.5AS-4 6.5 5.91” 5.43” 5.20” 3.90” 4.13” 4.57” (150.0±0.3mm) (138.0mm) (132.0mm) (99.0mm) (105.0mm) (116.0±0.3mm) 3.03” (77.0mm) 2.28” (58.0mm) .055” (1.4mm) FTAS00-8.4AS-4 8.4 7.34” 6.95” 6.73” 5.10” 5.33” 5.69” (186.5±0.3mm) (176.5mm) (170.9mm) (129.6mm) (135.4mm) (144.4±0.3mm) 3.73” (94.85mm) 2.84” (72.2mm) .083” (2.1mm) FTAS00-10.4AS-4 10.4 8.88” 8.46” 8.31” 6.24” 6.39” 6.75” (225.6±0.3mm) (215.0mm) (211.2mm) (158.4mm) (162.4mm) (171.4±0.3mm) 4.49” (114.1mm) 3.37” (85.7mm) .083” (2.1mm) L12 Dim A Dim B Viewable Area Dim C Active Area Dim D Active Area www.nkkswitches.com Dim E Viewable Area Dim G Dim H Center of Center of Active Area Active Area (Horizontal) (Vertical) Screen Size in Inches Dim F Dim J (1.25) Typ .049 (5.0) . 197 (0.8) Typ .031 Vertical Tail (0.3) ±0.05 .012 (10.0) .394 (0.5) .020 Pin 8 Pin 1 Stiffener (60.0) 2.36 (28.2) 1.110 (70.0) 2.76 (80.0) ±1.0 3.15 Contact Side Rockers (11.25) ±0.1 .443 Tail Pushbuttons TYPICAL DIMENSIONS Toggles Series FT 4-Wire Touch Screens with Printed Tails Insulation Film Programmable Illuminated PB Reinforcement Film 16 x 24 Reinforcement Film YUP Top Electrode H D X RI X LE F Keylocks E Bottom Electrode Rotaries Center of Active Area B A XLE XRI YLO Pins Signal 1, 2 YUP 3, 4 YLO 5, 6 X RI 7, 8 X LE L Indicators YUP 4-Wire Analog Touch Screen Dimensions Part Number Screen Size in Inches FTAS00-10.4AV-4 10.4 Dim A Dim B Viewable Area Dim C Active Area Dim D Active Area Dim E Viewable Area Dim F 8.92” (226.5±0.3mm) 8.52” (216.4mm) 8.35” (212.2mm) 6.28” (159.4mm) 6.43” (163.4mm) 7.20” (183.0±0.3mm) www.nkkswitches.com Touch Tilt 1 Dim G Dim H Center of Center of Active Area Active Area (Horizontal) (Vertical) 4.51” (114.5mm) 3.72” (94.5mm) L13 Accessories 8 XLE, XRI: Top Electrode Terminal YUP, YLO: Bottom Electrode Terminal Tactiles (2.1) ±0.2 .083 G Center of Active Area C Supplement (1.5) .059 Air Vent Slides YLO Toggles Series FT 4-Wire Touch Screens with Printed Tails TYPICAL DIMENSIONS Rockers Horizontal Tail & Narrow Frame Type 2 A B Viewable Area Pushbuttons C (1.5) Air Vent .059 Active Area (80.0) ±0.1 3.150 (70.0) 2.756 YUP Programmable Illuminated PB (60.0) 2.362 (5.0) ±1.0 .197 (1.25) Typ .049 H (10.0) ±1.0 .394 D Pin 1 E XRI XLE 1 F 8 (11.25) ±0.1 .443 Keylocks (0.8) Typ .031 Pin 8 (28.2) 1.110 Center of Active Area Reinforcement Film Rotaries YLO Slides G Center of Active Area Contact Side Tactiles (0.3) ±0.05 .012 Reinforcement Top Electrode Reinforcement Film YUP Tilt 1 XRI XLE 8 Touch YLO L (2.1) ±0.2 .083 Bottom Electrode Tail YUP, YLO: Top Electrode Terminal XLE, XRI : Bottom Electrode Terminal Pins Signal 1, 2 YUP 3, 4 YLO 5, 6 XLE 7, 8 XRI Screen Size in Inches Dim A Dim B Viewable Area Dim C Active Area Dim D Active Area Dim E Viewable Area Dim F Dim G Center of Active Area (Horizontal) Dim H Center of Active Area (Vertical) Accessories FTAS00-12.1AN-4 12.1 10.236” (260.0±0.3mm) 9.827” (249.6mm) 9.677” (245.8mm) 7.256” (184.3mm) 7.406” (188.1mm) 7.795” (198.0±0.3mm) 5.177” (131.5mm) 3.850” (97.8mm) FTAS00-15AN-4 15.0 12.669” (321.8.±0.3mm) 12.130” (308.1mm) 11.972” (304.1mm) 8.980” (228.1mm) 9.138” (232.1mm) 9.665” (245.5±0.3mm) 6.398” (162.5mm) 4.833” (122.75mm) FTAS00-19AN-4 19.0 15.571” (395.5.±0.3mm) 15.039” (382.0mm) 14.815” (376.3mm) 11.850” (301.0mm) 12.102” (307.4mm) 12.638” (321.0±0.3mm) 7.799” (198.1mm) 6.319” (160.5mm) Indicators Part Number Supplement Typical Dimensions L14 www.nkkswitches.com Series FT Toggles 4-Wire Touch Screens with Printed Tails TYPICAL DIMENSIONS Rockers Horizontal Tail & Wide Frame A B Viewable Area YUP (60.0) 2.362 Programmable Illuminated PB (5.0) ±1.0 .197 (1.25) Typ .049 (80.0) ±0.1 3.15 H (10.0) ±1.0 .394 D Pin 1 E XRI XLE 1 F 8 (11.25) ±0.1 .443 (0.8) Typ .031 Pin 8 (28.2) 1.110 Center of Active Area Reinforcement Film Keylocks YLO Reinforcement (2.1) ±0.2 .083 Bottom Electrode Reinforcement Film Slides (0.3) ±0.05 .012 Top Electrode Tactiles Tail Contact Side Rotaries G Center of Active Area 1 XRI XLE 8 YLO YUP, YLO: Top Electrode Terminal XLE, XRI : Bottom Electrode Terminal Pins Signal 1, 2 YUP 3, 4 YLO 5, 6 XLE 7, 8 XRI Tilt YUP L Touch (70.0) 2.756 (1.5) Air Vent .059 Active Area Pushbuttons C 4.933” (125.3mm) 2.984” (75.8mm) 10.827” (275.0±0.3mm) 10.404” 10.280” 6.425” 6.551” 6.929” 5.468” (264.26mm) (261.12mm) (163.2mm) (166.4mm) (176.0±0.3mm) (138.89mm) 3.465” (88.0mm) 14.276” (362.6±0.3mm) 13.681” (347.5mm) 4.217” (107.1mm) Dim A Dim B Viewable Area Dim C Active Area FTAS00-10.6AW-4 10.6 9.756” (247.8±0.3mm) 9.189” (233.4mm) 9.071” (230.4mm) FTAS00-12.1AW-4 12.1 FTAS00-15.6AW-4 15.6 13.551” (344.2mm) Dim D Active Area Dim E Viewable Area Dim F 5.441” 5.563” 6.094” (138.2mm) (141.3mm) (154.8±0.3mm) 7.618” 7.748” 8.433” (193.5mm) (196.8mm) (214.2±0.3mm) www.nkkswitches.com 7.138” (181.3mm) L15 Accessories Dim H Center of Active Area (Vertical) Screen Size in Inches Supplement Dim G Center of Active Area (Horizontal) Part Number Indicators Typical Dimensions Toggles Series FT 4-Wire Touch Screens with Printed Tails Controller Board for RS232C FTCS04B for RS232C Rockers (65.0) 2.559 (37.0) 1.457 (1.25) Typ .049 Symbol 1, 2 Y0 3, 4 Y1 5, 6 X0 7, 8 X1 1 (5.5) .217 CN3 1 CN2 (4.0) .157 For XRI or XLE Controller Board Side Pin Symbol No. (3.3) Dia Typ .130 Part No. CN2 RS232C Header Connector - 3 Pins (9.0) Typ* .354 * Pattern on Both Sides is Prohibited Area Direction of Tail Insertion Slider Contact Surface (5.6) .220 (5.4) .213 Keylocks For YUP or YLO 3 1 (0.5) .020 (1.6) .063 Description (0.5) .020 (8.0) .315 Pin No. S FTCS04B (3.5) .138 (5.0) .197 (7.0) .276 (0.5) .020 Computer Side Sending Data 1 RD Receiving Data (IN) 2 SD Sending Data (OUT) Receiving Data 3 GND GND GND CN3 Header Connector for Power Supply - 2 Pins Pin No. (0.35) Typ .014 (0.65) .026 Description (1.3) .051 Symbol Description 1 VCC Supply Voltage 2 GND GND Rotaries Controller Boards & Drivers DISTINCTIVE CHARACTERISTICS Controller Boards Type Slides • Compatible with Control Board USB/RS232C Part No. Communication Protocol • Equipped with EPROM for Saving Setting Data 4-Wire FTCS04B RS232C • Device Drivers are Windows 7 and 8 Compatible 4-Wire FTCU04B USB Tactiles System Configuration for USB USB Controller Board System Configuration for RS232C AT713 Receptacle Connector Connector RS232C Controller Board Connector Tilt Analog Touch Screen L USB Header Connector Analog Touch Screen IC Chip FTCSU548 RS232C Header Connector PC Install Device Driver Install Device Driver Monitor Header Connector for 5V IC Chip FTCSU548 AT714 Receptacle Connector Connects to Power Source 5V DC Power Supply Monitor Available through NKK Switches Indicators Touch 2 (7.5) .295 PC Accessories Pin No. (8.5) .335 Pin No. Pin No. (15.75) .620 (30.0) 1.181 USB Cable Supplement (17.0) .669 Lot No. CN1 (0.5) Typ .020 Programmable Illuminated PB (57.0) 2.244 8 Pushbuttons (3.65) Typ .144 CN1 4-Wire Analog Touch Screen Connector - 8 Pins General Specifications Items FTCS04B FTCU04B RS232C USB 2.0 Full Speed Clock 6MHz 6MHz Supply Voltage 5.0V 5.0V Resolution 10bit 10bit 40mA maximum 100mA maximum ______ Interface Current Consumption Communication Speed Communication Format L16 9600 bps Data Length: 8bit Parity: None Stop Bit: 1 www.nkkswitches.com ______ Touch panels can be operated the same as PC mouse functions by combining a control board or device driver and analog touch screen. For specifications or technical data for the controller boards and drivers, see NKK's web site or call our engineering support personnel. Series FT 4-Wire Touch Screens with Printed Tails VCC –0.3V +5.5V VT P ____ VCC Touch Panel Input *VRS –15V +15V RS232C Operating Temperature TO PR 0°C +32°F +70°C +158°F Storage Temperature TS TG –25°C –13°F +85°C +185°F ____ Notes Supply Voltage VCC +4.75V +5 +5.25V ____ Operating Temperature TO P R 0 ____ +70°C +158°F No Condensation ____ Programmable Illuminated PB ____ *VRS : Applies Only to RS232C Controller Boards Available for RS232C DISTINCTIVE CHARACTERISTICS • • • • Symbols Minimum Typical Maximum High Quality and Reliability Easy Integration Replacing Mouse Functionality Compatible with Control Board USB/RS232C Device Driver Compatible with Vista and Windows XP Operating Systems Keylocks Input Voltage Items Controller Boards Available for USB NKK offers controller boards compatible with USB or with RS232C. See web site or contact factory for specifications and technical data for any of the controller boards and drivers. Rotaries Supply Voltage Notes Toggles Maximum Rockers Minimum Pushbuttons Symbols IC Chip & Accessories DISTINCTIVE CHARACTERISTICS IC FTCSU548 The IC is for use with the 5- and 4-wire transparent touch screens, and is available for those who prefer to design their own controller boards. When the screen is touched, it recognizes the position of the touch by the level of analog voltage detected by the A/D. The A/D converter receives the value and sends a set of coordinate values as serial data or USB. Slides Package LFQFP 48 Pins Interface Serial Interface (Asynchronous) or USB (Full Speed 2.0) Supply Voltage 3.3/5.0V Typ; USB Available for 5V Only * Rated Output Current High Level: –170mA Low Level: +170mA Operation Frequency 16MHz A/D Converter Resolution 10bit Operating Temperature –20°C ~ +85°C (–4°F ~ +185°F) Storage Temperature –40°C ~ +125°C (–40°F ~ +257°F) L * Total Output Electric Current Amount of all the I/O Port AT714 Receptacle Connector This Receptacle Connector with code connects to RS232C communication of the controller boards. AT714 is a Receptacle Connector with code to connect to power source of the control boards. Accessories OPTIONAL ACCESSORIES AT713 Receptacle Connector For more details and dimensioned drawings of the accessories, go to NKK’s web site or call our engineering support personnel. www.nkkswitches.com Tactiles Interface: USB and RS232C High Speed and Accuracy Built-in Calibration Function Data Function Removal Built In to Eliminate Noise Tilt • • • • Indicators General Specifications for IC FTCSU548 Touch Items Recommended Values L17 Supplement Absolute Maximum Ratings Toggles Series FT Touch Screens STORAGE, HANDLING & INSTALLATION Rockers Handling of Controller Board • Use arc prevention to protect device from static electricity. • Power source should be activated after host and touch panel are connected. Pushbuttons • When inserting connector CN1 and touch panel tail, be sure the slider of connector CN1 is pulled. Do not pull more than 10 times. • Do not alter the product. • Do not use any commands other than the ones outlined in the specifications. Programmable Illuminated PB • Place the product away from noise source (such as inverter from LCD operation) since tail can be affected by noise. • If device driver (USB) does not work after installation, reboot the host computer while connected to the controller board. • This product does not support suspended mode (USB). • Protocol of USB transmission is one frame per one transaction. • Contact factory if not using the protocol above. • Warranty for one year after delivery. NKK warranties the 4-wire touch panel when it is used with the NKK control board and driver. Do not use third party control boards. NKK is not responsible for results of using damaged equipment with the controller boards. Keylocks • NKK Switches cannot assume responsibility for damages caused by software side during use of the touch screens. Rotaries • The touch screen pressed position may shift depending on various factors such as age, improper tail insertion or extreme tempera- tures. In such cases, recalibration is necessary. Installation • Products are ESD sensitive and ESD protection is required. • Do not pull on the tail. Do not apply stress to the tail area. Slides • Avoid vibration or shock. Avoid any force or stress that may cause deformation to the product. • The touch screen mounting should not be loose. This may cause an adverse effect on detecting performance during operation. Supplement Accessories Indicators Touch Tilt Tactiles • Ensure there are no burrs around the edges of the case or housing that can cause false actuation. The edges of the case or housing should not enter the keying area. L • The case or housing and upper electrode should have a space of about 0.5mm to accommodate expansion or shrinkage due to temperature variances. If a shock barrier is used, do not press hard on the upper electrode area. Any shock barrier should be installed more than 0.6mm away from A. Case/Housing Cushioning Material (0.5) Approx. .020 A Top Electrode (Film) Adhesive Layer * Sealing Material LCD (0.6) Min. .020 Bottom Electrode (Glass) Active Area Visible Area Example of Burr on Housing Interferes with Operation at Point A * Example: Double-sided Tape • To secure the touch screen, secure the lower portion with a device such as the LCD display panel. Do not attach the upper electrode with double-sided tape or similar product to avoid stress that can damage the upper or lower electrode. • In order to balance upper and lower pressure, an air vent may be installed. Ensure that no liquid or oil will enter into the device. • Avoid air pressure applied to the touch screen as it may cause the top electrode to force air through the air vent, effecting electric endurance. If pressure inside of the touch panel is reduced through the air vent, it may cause interference fringes or may remain in ON status. • Ensure that the glass is handled carefully to prevent breakage during installation. • Moisture from condensation on tail connection or edges may result in migration, causing short circuit failure. • Remove protective film from the touch screen after installation is completed. L24 www.nkkswitches.com Toggles Series FT Touch Screens STORAGE, HANDLING & INSTALLATION Rockers Handling Precautions • When opening product, take precaution with up/down and front/back directions. Glass edges are not chamfered, and corners or edges can be sharp. Wear gloves when handling the product. Pushbuttons • Do not pick up the product by the tail or pull the tail area. • Use gloves or finger cots to prevent fingerprints on surface. • When handling the product, hold it outside of the viewing area. Programmable Illuminated PB • Avoid stacking multiple products or placing other items on the product. • When packing or storing, the glass should be positioned face up. Operating Precautions • Operate with fingers or a touch screen stylus only. Keylocks • Do not press hard with a pen or similar object between viewing area and key area. Rotaries Design Precautions • With analog type, resistive value change (by aging or individual differences) can dislocate the input area. Input area can be calibrated with software. Slides • When installing on top of an LCD, noise from the display device can create misoperation. To avoid noise, implement grounding the display device frame. • Do not create software for simultaneous touch points, as analog type will read the center point between two touch points. • When used to draw a line, analog type will have a break at dot spacer. Compensate for this with software. Tactiles • Contact resistance may cause chatter depending on pressing condition. Software should detect signal after it stabilizes. Other Precautions Tilt • Clean with a soft cloth and ethanol. Do not use any cleaning agents other than ethanol. • Store product in original package and store at the temperature and humidity range specified. • Products are guaranteed based on evaluation of standards within the moisture tolerance and usage temperature range, but not guaranteed to operate perpetually at this temperature. L Touch • Do not store in an environment with acids or other corrosive gases or where condensation may occur. • Note that an incorrect type of connector may damage the print surface. Indicators • Calibration data from one touch panel should not be applied to another panel; each should be calibrated individually. • Recalibration is necessary if connector has been removed from the tail and reconnected. • All specifications based on the tested touch screens only. Evaluate the products after installation with customer's equipment. Supplement Accessories • NKK Switches reserves the right to make product improvement changes without notice. www.nkkswitches.com L25