ADC14C080

ADC14C065/ADC14C080/ADC14C095/ADC14C105 14-Bit, 65/80/95/105 MSPS A/D Converter ADVANCE INFORMATION September 2006 ADC14C065/ADC14C080/ADC14C095/ADC14C105 14-Bit, 65/80/95/105 MSPS A/D Converter General Description NOTE: This is Advance Information for products currently in development. ALL specifications are design targets and are subject to change. The ADC14C065, ADC14C080, ADC14C095, and ADC14105 are high-performance CMOS analog-to-digital converters capable of converting analog input signals into 14-bit digital words at rates up to 65/80/95/105 Mega Samples Per Second (MSPS) respectively. These converters use a differential, pipelined architecture with digital error correction and an on-chip sample-and-hold circuit to minimize power consumption and the external component count, while providing excellent dynamic performance. A unique sample-and-hold stage yields a full-power bandwidth of 1 GHz. The ADC14C065/080/095/105 may be operated from a single +3.3V power supply and consumes low power. A separate +2.5V supply may be used for the digital output interface which allows lower power operation with reduced noise. A power-down feature reduces the power consumption to very low levels while still allowing fast wake-up time to full operation. The differential inputs provide a 2V full scale differential input swing. A stable 1.2V internal voltage reference is provided, or the ADC14C065/080/095/105 can be operated with an external 1.2V reference. Output data format (offset binary versus 2’s complement) and duty cycle stabilizer are pin-selectable. The duty cycle stabilizer maintains performance over a wide range of clock duty cycles. The ADC14C065/080/095/105 is available in a 32-lead LLP package and operates over the industrial temperature range of −40˚C to +85˚C. Features n n n n n n n n n n 1 GHz Full Power Bandwidth Internal sample-and-hold circuit Low power consumption Internal precision reference Data Ready output clock Clock Duty Cycle Stabilizer Single +3.3V supply operation Power-down mode Offset binary or 2’s complement output data format 32-pin LLP package, (5x5x0.8mm, 0.5mm pin-pitch) Key Specifications n n n n n n n For ADC14C105 Resolution Conversion Rate SNR (fIN = 240 MHz) SFDR (fIN = 240 MHz) Full Power Bandwidth Power Consumption 14 Bits 105 MSPS 72 dBFS (typ) 83 dBFS (typ) 1 GHz (typ) 400 mW (typ) Applications n n n n n High IF Sampling Receivers Wireless Base Station Receivers Test and Measurement Equipment Communications Instrumentation Portable Instrumentation Connection Diagram 20209801 © 2006 National Semiconductor Corporation DS202098 www.national.com ADC14C065/ADC14C080/ADC14C095/ADC14C105 Block Diagram 20209802 Ordering Information Industrial (−40˚C ≤ TA ≤ +85˚C) ADC14C065CISQ ADC14C080CISQ ADC14C095CISQ ADC14C105CISQ Package 32 Pin LLP 32 Pin LLP 32 Pin LLP 32 Pin LLP www.national.com 2 ADC14C065/ADC14C080/ADC14C095/ADC14C105 Pin Descriptions and Equivalent Circuits Pin No. ANALOG I/O Symbol Equivalent Circuit Description 5 VIN+ Differential analog input pins. The differential full-scale input signal level is 2VP-P with each input pin signal centered on a common mode voltage, VCM. 6 VIN- 2 VRP 32 VCMO 1 VRN These pins should each be bypassed to AGND with a low ESL (equivalent series inductance) 1 µF capacitor placed very close to the pin to minimize stray inductance. A 0.1 µF capacitor should be placed between VRP and VRN as close to the pins as possible, and a 1 µF capacitor should be placed in parallel. VRP and VRN should not be loaded. VCMO may be loaded to 1mA for use as a temperature stable 1.5V reference. It is recommended to use VCMO to provide the common mode voltage, VCM, for the differential analog inputs, VIN+ and VIN−. 31 VREF Reference Voltage. This device provides an internally developed 1.2V reference. When using the internal reference, VREF should be decoupled to AGND with a 0.1 µF and a 1 µF low equivalent series inductance (ESL) capacitor . This pin may be driven with an external 1.2V reference voltage. This pin should not be used to source or sink current. DIGITAL I/O 11 CLK The clock input pin. The analog input is sampled on the rising edge of the clock input. 12 OF/DCS This is a four-state pin controlling the input clock mode and output data format. OF/DCS = VA, output data format is 2’s complement without duty cycle stabilization applied to the input clock OF/DCS = AGND, output data format is offset binary, without duty cycle stabilization applied to the input clock. OF/DCS = (2/3)*VA, output data is 2’s complement with duty cycle stabilization applied to the input clock OF/DCS = (1/3)*VA, output data is offset binary with duty cycle stabilization applied to the input clock. This is a two-state input controlling Power Down. PD = VA, Power Down is enabled and power dissipation is reduced. PD = AGND, Normal operation. 30 PD 3 www.national.com ADC14C065/ADC14C080/ADC14C095/ADC14C105 Pin Descriptions and Equivalent Circuits Pin No. Symbol Equivalent Circuit (Continued) Description 13-19, 23-29 D0–D13 Digital data output pins that make up the 14-bit conversion result. D0 (pin 13) is the LSB, while D13 (pin 29) is the MSB of the output word. Output levels are CMOS compatible. 21 DRDY Data Ready Strobe. The data output transition is synchronized with the falling edge of this signal. This signal switches at the same frequency as the CLK input. ANALOG POWER 3, 8, 10, 4, 7, 9, Exposed Pad DIGITAL POWER 20 VDR Positive driver supply pin for the output drivers. This pin should be connected to a quiet voltage source and be bypassed to DRGND with a 0.1 µF capacitor located close to the power pin. The ground return for the digital output driver supply. This pins should be connected to the system digital ground, but not be connected in close proximity to the ADC’s AGND pins. VA Positive analog supply pins. These pins should be connected to a quiet voltage source and be bypassed to AGND with 0.1 µF capacitors located close to the power pins. The ground return for the analog supply. AGND 22 DRGND www.national.com 4 ADC14C065/ADC14C080/ADC14C095/ADC14C105 Absolute Maximum Ratings 3) (Notes 1, Operating Ratings (Notes 1, 3) Operating Temperature Supply Voltage (VA) (ADC14C065,ADC14C080) (ADC14C095,ADC14C105) Output Driver Supply (VDR) Clock Duty Cycle (DCS Enabled) (DCS disabled) VCM |AGND-DRGND| 30/70 % 45/55 % 1.4V to 1.6V ≤100mV +2.7V to +3.6V +3.0V to +3.6V +2.25V to VA −40˚C ≤ TA ≤ +85˚C If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VA, VDR) Voltage on Any Pin (Not to exceed 4.2V) Input Current at Any Pin other than Supply Pins (Note 4) Package Input Current (Note 4) Max Junction Temp (TJ) Thermal Resistance (θJA) ESD Rating Human Body Model (Note 6) Machine Model (Note 6) Storage Temperature 2500V 250V −65˚C to +150˚C −0.3V to 4.2V −0.3V to (VA +0.3V) ± 5 mA ± 50 mA +150˚C 30˚C/W Soldering process must comply with National Semiconductor’s Reflow Temperature Profile specifications. Refer to www.national.com/packaging. (Note 7) ADC14C065 Converter Electrical Characteristics This product is currently under development. As such, the parameters specified are DESIGN TARGETS. The specifications cannot be guaranteed until device characterization has taken place. Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.0V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 65 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits Units (Limits) Bits (min) LSB (max) LSB (min) LSB (max) LSB (min) 0 16383 1.45 1.55 1.4 1.6 V (min) V (max) V (min) V (max) pF pF 1.176 1.224 V (min) V (max) STATIC CONVERTER CHARACTERISTICS Resolution with No Missing Codes INL DNL Integral Non Linearity (Note 11) Differential Non Linearity Under Range Output Code Over Range Output Code REFERENCE AND ANALOG INPUT CHARACTERISTICS VCMO VCM CIN VREF Common Mode Output Voltage Analog Input Common Mode Voltage VIN Input Capacitance (each pin to GND) (Note 12) External Reference Voltage VIN = 1.5 Vdc ± 0.5 V (CLK LOW) (CLK HIGH) 1.5 1.5 8.5 3.5 1.20 14 ± 1.5 ± 0.5 0 16383 5 www.national.com ADC14C065/ADC14C080/ADC14C095/ADC14C105 ADC14C065 Dynamic Converter Electrical Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.0V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 65 MHz, VCM = VCMO, CL = 5 pF/pin, . Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Note 8) (Note 9) Symbol Parameter Conditions Typical (Note 10) 1.0 74.3 72 72 90 88 83 12 11.6 11.6 −88 −85 −80 −100 −95 −85 −90 −88 −83 74.1 71.8 71.4 Limits Units (Limits) GHz dBFS dBFS dBFS dBFS dBFS dBFS Bits Bits Bits dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS DYNAMIC CONVERTER CHARACTERISTICS, AIN = -1dBFS FPBW SNR Full Power Bandwidth Signal-to-Noise Ratio -1 dBFS Input, −3 dB Corner fIN = 10 MHz fIN = 70 MHz fIN = 170 MHz fIN = 10 MHz SFDR Spurious Free Dynamic Range fIN = 70 MHz fIN = 170 MHz fIN = 10 MHz ENOB Effective Number of Bits fIN = 70 MHz fIN = 170 MHz fIN = 10 MHz THD Total Harmonic Disortion fIN = 70 MHz fIN = 170 MHz fIN = 10 MHz H2 Second Harmonic Distortion fIN = 70 MHz fIN = 170 MHz fIN = 10 MHz H3 Third Harmonic Distortion fIN = 70 MHz fIN = 170 MHz SINAD Signal-to-Noise and Distortion Ratio fIN = 10 MHz fIN = 70 MHz fIN = 170 MHz ADC14C065 Logic and Power Supply Electrical Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.0V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 65 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits Units (Limits) V (min) V (max) µA µA pF 1.2 0.4 −10 10 5 Full Operation Full Operation (Note 13) 90 11.5 V (min) V (max) mA mA pF mA (max) mA DIGITAL INPUT CHARACTERISTICS (CLK, PD) VIN(1) VIN(0) IIN(1) IIN(0) CIN VOUT(1) VOUT(0) +ISC −ISC COUT IA IDR Logical “1” Input Voltage Logical “0” Input Voltage Logical “1” Input Current Logical “0” Input Current Digital Input Capacitance Logical “1” Output Voltage Logical “0” Output Voltage Output Short Circuit Source Current Output Short Circuit Sink Current Digital Output Capacitance Analog Supply Current Digital Output Supply Current IOUT = −0.5 mA , VDR = 1.8V IOUT = 1.6 mA, VDR = 1.8V VOUT = 0V VOUT = VDR VD = 3.6V VD = 3.0V VIN = 3.3V VIN = 0V 10 −10 5 2.0 0.8 DIGITAL OUTPUT CHARACTERISTICS (D0–D13, DRDY) POWER SUPPLY CHARACTERISTICS www.national.com 6 ADC14C065/ADC14C080/ADC14C095/ADC14C105 ADC14C065 Logic and Power Supply Electrical Characteristics (Continued) Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.0V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 65 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symbol Parameter Power Consumption Power Down Power Consumption Conditions Excludes IDR (Note 13) Clock disabled Typical (Note 10) 270 5 Limits Units (Limits) mW (max) mW ADC14C065 Timing and AC Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.0V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 65 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Timing measurements are taken at 50% of the signal amplitude. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symb Parameter Maximum Clock Frequency Minimum Clock Frequency tCH tCL tCONV tOD tSU tH tAD tAJ Clock High Time Clock Low Time Conversion Latency Output Delay of CLK to DATA Data Output Setup Time Data Output Hold Time Aperture Delay Aperture Jitter Relative to rising edge of CLK Relative to DRDY Relative to DRDY 4 6 6 0.6 0.1 7 7 7 2 6 Conditions Typical (Note 10) Limits 65 20 Units (Limits) MHz (max) MHz (min) ns ns Clock Cycles ns (min) ns(max) ns (min) ns (min) ns ps rms 7 www.national.com ADC14C065/ADC14C080/ADC14C095/ADC14C105 ADC14C080 Converter Electrical Characteristics This product is currently under development. As such, the parameters specified are DESIGN TARGETS. The specifications cannot be guaranteed until device characterization has taken place. Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.0V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 80 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits Units (Limits) STATIC CONVERTER CHARACTERISTICS Resolution with No Missing Codes INL DNL Integral Non Linearity (Note 11) Differential Non Linearity Under Range Output Code Over Range Output Code REFERENCE AND ANALOG INPUT CHARACTERISTICS VCMO VCM CIN VREF Common Mode Output Voltage Analog Input Common Mode Voltage VIN Input Capacitance (each pin to GND) (Note 12) External Reference Voltage VIN = 1.5 Vdc ± 0.5 V (CLK LOW) (CLK HIGH) 1.5 1.5 8.5 3.5 1.20 1.176 1.224 1.45 1.55 1.4 1.6 V (min) V (max) V (min) V (max) pF pF V (min) V (max) 14 Bits (min) LSB (max) LSB (min) LSB (max) LSB (min) 0 16383 ± 1.5 ± 0.5 0 16383 ADC14C080 Dynamic Converter Electrical Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.0V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 80 MHz, VCM = VCMO, CL = 5 pF/pin, . Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Note 8) (Note 9) Symbol Parameter Conditions Typical (Note 10) 1.0 74.2 72 72 90 88 83 12 11.6 11.6 −90 −85 −80 −100 −95 −85 −90 −88 −83 Limits Units (Limits) GHz dBFS dBFS dBFS dBFS dBFS dBFS Bits Bits Bits dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS DYNAMIC CONVERTER CHARACTERISTICS, AIN = -1dBFS FPBW SNR Full Power Bandwidth Signal-to-Noise Ratio -1 dBFS Input, −3 dB Corner fIN = 10 MHz fIN = 70 MHz fIN = 170 MHz fIN = 10 MHz SFDR Spurious Free Dynamic Range fIN = 70 MHz fIN = 170 MHz fIN = 10 MHz ENOB Effective Number of Bits fIN = 70 MHz fIN = 170 MHz fIN = 10 MHz THD Total Harmonic Disortion fIN = 70 MHz fIN = 170 MHz fIN = 10 MHz H2 Second Harmonic Distortion fIN = 70 MHz fIN = 170 MHz fIN = 10 MHz H3 Third Harmonic Distortion fIN = 70 MHz fIN = 170 MHz www.national.com 8 ADC14C065/ADC14C080/ADC14C095/ADC14C105 ADC14C080 Dynamic Converter Electrical Characteristics (Continued) Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.0V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 80 MHz, VCM = VCMO, CL = 5 pF/pin, . Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Note 8) (Note 9) Symbol Parameter Signal-to-Noise and Distortion Ratio Conditions fIN = 10 MHz fIN = 70 MHz fIN = 170 MHz Typical (Note 10) 74 71.8 71.4 Limits Units (Limits) dBFS dBFS dBFS SINAD ADC14C080 Logic and Power Supply Electrical Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.0V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 80 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits Units (Limits) V (min) V (max) µA µA pF 1.2 0.4 −10 10 5 Full Operation Full Operation (Note 13) Excludes IDR (Note 13) Clock disabled 100 13 300 5 V (min) V (max) mA mA pF mA (max) mA mW (max) mW DIGITAL INPUT CHARACTERISTICS (CLK, PD) VIN(1) VIN(0) IIN(1) IIN(0) CIN VOUT(1) VOUT(0) +ISC −ISC COUT IA IDR Logical “1” Input Voltage Logical “0” Input Voltage Logical “1” Input Current Logical “0” Input Current Digital Input Capacitance Logical “1” Output Voltage Logical “0” Output Voltage Output Short Circuit Source Current Output Short Circuit Sink Current Digital Output Capacitance Analog Supply Current Digital Output Supply Current Power Consumption Power Down Power Consumption IOUT = −0.5 mA , VDR = 1.8V IOUT = 1.6 mA, VDR = 1.8V VOUT = 0V VOUT = VDR VD = 3.6V VD = 3.0V VIN = 3.3V VIN = 0V 10 −10 5 2.0 0.8 DIGITAL OUTPUT CHARACTERISTICS (D0–D13, DRDY) POWER SUPPLY CHARACTERISTICS ADC14C080 Timing and AC Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.0V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 80 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Timing measurements are taken at 50% of the signal amplitude. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symb Parameter Maximum Clock Frequency Minimum Clock Frequency tCH tCL tCONV tOD tSU tH tAD tAJ Clock High Time Clock Low Time Conversion Latency Output Delay of CLK to DATA Data Output Setup Time Data Output Hold Time Aperture Delay Aperture Jitter Relative to rising edge of CLK Relative to DRDY Relative to DRDY 4 5 5 0.6 0.1 6 6 7 2 6 Conditions Typical (Note 10) Limits 80 20 Units (Limits) MHz (max) MHz (min) ns ns Clock Cycles ns (min) ns(max) ns (min) ns (min) ns ps rms 9 www.national.com ADC14C065/ADC14C080/ADC14C095/ADC14C105 ADC14C095 Converter Electrical Characteristics This product is currently under development. As such, the parameters specified are DESIGN TARGETS. The specifications cannot be guaranteed until device characterization has taken place. Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 95 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits Units (Limits) Bits (min) LSB (max) LSB (min) LSB (max) LSB (min) 0 16383 1.45 1.55 1.4 1.6 V (min) V (max) V (min) V (max) pF pF 1.176 1.224 V (min) V (max) STATIC CONVERTER CHARACTERISTICS Resolution with No Missing Codes INL DNL Integral Non Linearity (Note 11) Differential Non Linearity Under Range Output Code Over Range Output Code REFERENCE AND ANALOG INPUT CHARACTERISTICS VCMO VCM CIN VREF Common Mode Output Voltage Analog Input Common Mode Voltage VIN Input Capacitance (each pin to GND) (Note 12) External Reference Voltage VIN = 1.5 Vdc ± 0.5 V (CLK LOW) (CLK HIGH) 1.5 1.5 8.5 3.5 1.20 14 ± 1.5 ± 0.5 0 16383 ADC14C095 Dynamic Converter Electrical Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 95 MHz, VCM = VCMO, CL = 5 pF/pin, . Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Note 8) (Note 9) Symbol Parameter Conditions Typical (Note 10) 1.0 73.7 72 72 90 88 83 11.9 11.6 11.6 −88 −85 −80 -95 −90 −85 −90 −88 −83 Limits Units (Limits) GHz dBFS dBFS dBFS dBFS dBFS dBFS Bits Bits Bits dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS DYNAMIC CONVERTER CHARACTERISTICS, AIN = -1dBFS FPBW SNR Full Power Bandwidth Signal-to-Noise Ratio -1 dBFS Input, −3 dB Corner fIN = 10 MHz fIN = 70 MHz fIN = 240 MHz fIN = 10 MHz SFDR Spurious Free Dynamic Range fIN = 70 MHz fIN = 240 MHz fIN = 10 MHz ENOB Effective Number of Bits fIN = 70 MHz fIN = 240 MHz fIN = 10 MHz THD Total Harmonic Disortion fIN = 70 MHz fIN = 240 MHz fIN = 10 MHz H2 Second Harmonic Distortion fIN = 70 MHz fIN = 240 MHz fIN = 10 MHz H3 Third Harmonic Distortion fIN = 70 MHz fIN = 240 MHz www.national.com 10 ADC14C065/ADC14C080/ADC14C095/ADC14C105 ADC14C095 Dynamic Converter Electrical Characteristics (Continued) Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 95 MHz, VCM = VCMO, CL = 5 pF/pin, . Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Note 8) (Note 9) Symbol Parameter Signal-to-Noise and Distortion Ratio Conditions fIN = 10 MHz fIN = 70 MHz fIN = 240 MHz Typical (Note 10) 73.5 71.7 71.6 Limits Units (Limits) dBFS dBFS dBFS SINAD ADC14C095 Logic and Power Supply Electrical Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 95 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits Units (Limits) V (min) V (max) µA µA pF 1.2 0.4 −10 10 5 Full Operation Full Operation (Note 13) Excludes IDR (Note 13) Clock disabled 115 14.5 380 5 V (min) V (max) mA mA pF mA (max) mA mW (max) mW DIGITAL INPUT CHARACTERISTICS (CLK, PD) VIN(1) VIN(0) IIN(1) IIN(0) CIN VOUT(1) VOUT(0) +ISC −ISC COUT IA IDR Logical “1” Input Voltage Logical “0” Input Voltage Logical “1” Input Current Logical “0” Input Current Digital Input Capacitance Logical “1” Output Voltage Logical “0” Output Voltage Output Short Circuit Source Current Output Short Circuit Sink Current Digital Output Capacitance Analog Supply Current Digital Output Supply Current Power Consumption Power Down Power Consumption IOUT = −0.5 mA , VDR = 1.8V IOUT = 1.6 mA, VDR = 1.8V VOUT = 0V VOUT = VDR VD = 3.6V VD = 3.0V VIN = 3.3V VIN = 0V 10 −10 5 2.0 0.8 DIGITAL OUTPUT CHARACTERISTICS (D0–D13, DRDY) POWER SUPPLY CHARACTERISTICS ADC14C095 Timing and AC Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 95 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Timing measurements are taken at 50% of the signal amplitude. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symb Parameter Maximum Clock Frequency Minimum Clock Frequency tCH tCL tCONV tOD tSU tH tAD tAJ Clock High Time Clock Low Time Conversion Latency Output Delay of CLK to DATA Data Output Setup Time Data Output Hold Time Aperture Delay Aperture Jitter Relative to rising edge of CLK Relative to DRDY Relative to DRDY 4 4 4 0.6 0.1 5 5 7 2 6 Conditions Typical (Note 10) Limits 95 20 Units (Limits) MHz (max) MHz (min) ns ns Clock Cycles ns (min) ns (max) ns (min) ns (min) ns ps rms 11 www.national.com ADC14C065/ADC14C080/ADC14C095/ADC14C105 ADC14C105 Converter Electrical Characteristics This product is currently under development. As such, the parameters specified are DESIGN TARGETS. The specifications cannot be guaranteed until device characterization has taken place. Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 105 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits Units (Limits) Bits (min) LSB (max) LSB (min) LSB (max) LSB (min) 0 16383 1.45 1.55 1.4 1.6 V (min) V (max) V (min) V (max) pF pF 1.176 1.224 V (min) V (max) STATIC CONVERTER CHARACTERISTICS Resolution with No Missing Codes INL DNL Integral Non Linearity (Note 11) Differential Non Linearity Under Range Output Code Over Range Output Code REFERENCE AND ANALOG INPUT CHARACTERISTICS VCMO VCM CIN VREF Common Mode Output Voltage Analog Input Common Mode Voltage VIN Input Capacitance (each pin to GND) (Note 12) External Reference Voltage VIN = 1.5 Vdc ± 0.5 V (CLK LOW) (CLK HIGH) 1.5 1.5 8.5 3.5 1.20 14 ± 1.5 ± 0.5 0 16383 ADC14C105 Dynamic Converter Electrical Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 105 MHz, VCM = VCMO, CL = 5 pF/pin, . Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Note 8) (Note 9) Symbol Parameter Conditions Typical (Note 10) 1.0 73 72.5 72 88 85 83 11.8 11.7 11.6 −86 −85 −80 −95 −90 −85 −88 −85 −83 Limits Units (Limits) GHz dBFS dBFS dBFS dBFS dBFS dBFS Bits Bits Bits dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS DYNAMIC CONVERTER CHARACTERISTICS, AIN = -1dBFS FPBW SNR Full Power Bandwidth Signal-to-Noise Ratio -1 dBFS Input, −3 dB Corner fIN = 10 MHz fIN = 70 MHz fIN = 240 MHz fIN = 10 MHz SFDR Spurious Free Dynamic Range fIN = 70 MHz fIN = 240 MHz fIN = 10 MHz ENOB Effective Number of Bits fIN = 70 MHz fIN = 240 MHz fIN = 10 MHz THD Total Harmonic Disortion fIN = 70 MHz fIN = 240 MHz fIN = 10 MHz H2 Second Harmonic Distortion fIN = 70 MHz fIN = 240 MHz fIN = 10 MHz H3 Third Harmonic Distortion fIN = 70 MHz fIN = 240 MHz www.national.com 12 ADC14C065/ADC14C080/ADC14C095/ADC14C105 ADC14C105 Dynamic Converter Electrical Characteristics (Continued) Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 105 MHz, VCM = VCMO, CL = 5 pF/pin, . Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Note 8) (Note 9) Symbol Parameter Signal-to-Noise and Distortion Ratio Conditions fIN = 10 MHz fIN = 70 MHz fIN = 240 MHz Typical (Note 10) 72.8 72.3 71.4 Limits Units (Limits) dBFS dBFS dBFS SINAD ADC14C105 Logic and Power Supply Electrical Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 105 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits Units (Limits) V (min) V (max) µA µA pF 1.2 0.4 −10 10 5 Full Operation Full Operation (Note 13) Excludes IDR (Note 13) Clock disabled 121 16 400 5 V (min) V (max) mA mA pF mA (max) mA mW (max) mW DIGITAL INPUT CHARACTERISTICS (CLK, PD) VIN(1) VIN(0) IIN(1) IIN(0) CIN VOUT(1) VOUT(0) +ISC −ISC COUT IA IDR Logical “1” Input Voltage Logical “0” Input Voltage Logical “1” Input Current Logical “0” Input Current Digital Input Capacitance Logical “1” Output Voltage Logical “0” Output Voltage Output Short Circuit Source Current Output Short Circuit Sink Current Digital Output Capacitance Analog Supply Current Digital Output Supply Current Power Consumption Power Down Power Consumption IOUT = −0.5 mA , VDR = 1.8V IOUT = 1.6 mA, VDR = 1.8V VOUT = 0V VOUT = VDR VD = 3.6V VD = 3.0V VIN = 3.3V VIN = 0V 10 −10 5 2.0 0.8 DIGITAL OUTPUT CHARACTERISTICS (D0–D13, DRDY) POWER SUPPLY CHARACTERISTICS ADC14C105 Timing and AC Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF = +1.2V, fCLK = 105 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25˚C. Timing measurements are taken at 50% of the signal amplitude. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25˚C (Notes 8, 9) Symb Parameter Maximum Clock Frequency Minimum Clock Frequency tCH tCL tCONV tOD tSU tH tAD tAJ Clock High Time Clock Low Time Conversion Latency Output Delay of CLK to DATA Data Output Setup Time Data Output Hold Time Aperture Delay Aperture Jitter Relative to rising edge of CLK Relative to DRDY Relative to DRDY 4 3 3 0.6 0.1 4 4 7 2 6 Conditions Typical (Note 10) Limits 105 20 Units (Limits) MHz (max) MHz (min) ns ns Clock Cycles ns (min) ns (max) ns (min) ns (min) ns ps rms 13 www.national.com ADC14C065/ADC14C080/ADC14C095/ADC14C105 ADC14C105 Timing and AC Characteristics (Continued) Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is guaranteed to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Operation of the device beyond the maximum Operating Ratings is not recommended. Note 2: Parameters specified in dBFS indicate the value that would be attained with a full-scale input signal. Note 3: All voltages are measured with respect to GND = AGND = DRGND = 0V, unless otherwise specified. Note 4: When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND, or VIN > VA), the current at that pin should be limited to ± 5 mA. The ± 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of ± 5 mA to 10. Note 5: The maximum allowable power dissipation is dictated by TJ,max, the junction-to-ambient thermal resistance, (θJA), and the ambient temperature, (TA), and can be calculated using the formula PD,max = (TJ,max - TA )/θJA. The values for maximum power dissipation listed above will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Such conditions should always be avoided. Note 6: Human Body Model is 100 pF discharged through a 1.5 kΩ resistor. Machine Model is 220 pF discharged through 0 Ω Note 7: Reflow temperature profiles are different for lead-free and non-lead-free packages. Note 8: The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided current is limited per (Note 4). However, errors in the A/D conversion can occur if the input goes above 2.6V or below GND as described in the Operating Ratings section. 20209811 Note 9: With a full scale differential input of 2VP-P , the 14-bit LSB is 122.1 µV. Note 10: Typical figures are at TA = 25˚C and represent most likely parametric norms at the time of product characterization. The typical specifications are not guaranteed. Note 11: Integral Non Linearity is defined as the deviation of the analog value, expressed in LSBs, from the straight line that passes through positive and negative full-scale. Note 12: The input capacitance is the sum of the package/pin capacitance and the sample and hold circuit capacitance. Note 13: IDR is the current consumed by the switching of the output drivers and is primarily determined by load capacitance on the output pins, the supply voltage, VDR, and the rate at which the outputs are switching (which is signal dependent). IDR=VDR(C0 x f0 + C1 x f1 +....C11 x f11) where VDR is the output driver power supply voltage, Cn is total capacitance on the output pin, and fn is the average frequency at which that pin is toggling. www.national.com 14 ADC14C065/ADC14C080/ADC14C095/ADC14C105 Specification Definitions APERTURE DELAY is the time after the falling edge of the clock to when the input signal is acquired or held for conversion. APERTURE JITTER (APERTURE UNCERTAINTY) is the variation in aperture delay from sample to sample. Aperture jitter manifests itself as noise in the output. CLOCK DUTY CYCLE is the ratio of the time during one cycle that a repetitive digital waveform is high to the total time of one period. The specification here refers to the ADC clock input signal. COMMON MODE VOLTAGE (VCM) is the common DC voltage applied to both input terminals of the ADC. CONVERSION LATENCY is the number of clock cycles between initiation of conversion and when that data is presented to the output driver stage. Data for any given sample is available at the output pins the Pipeline Delay plus the Output Delay after the sample is taken. New data is available at every clock cycle, but the data lags the conversion by the pipeline delay. DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1 LSB. EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise and Distortion Ratio or SINAD. ENOB is defined as (SINAD 1.76) / 6.02 and says that the converter is equivalent to a perfect ADC of this (ENOB) number of bits. FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental drops 3 dB below its low frequency value for a full scale input. GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated as: Gain Error = Positive Full Scale Error − Negative Full Scale Error It can also be expressed as Positive Gain Error and Negative Gain Error, which are calculated as: PGE = Positive Full Scale Error - Offset Error NGE = Offset Error - Negative Full Scale Error INTEGRAL NON LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from negative full scale (1⁄2 LSB below the first code transition) through positive full scale (1⁄2 LSB above the last code transition). The deviation of any given code from this straight line is measured from the center of that code value. INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the power in the intermodulation products to the total power in the original frequencies. IMD is usually expressed in dBFS. LSB (LEAST SIGNIFICANT BIT) is the bit that has the smallest value or weight of all bits. This value is VFS/2n, where “VFS” is the full scale input voltage and “n” is the ADC resolution in bits. MISSING CODES are those output codes that will never appear at the ADC outputs. The ADC14C065 is guaranteed not to have any missing codes. MSB (MOST SIGNIFICANT BIT) is the bit that has the largest value or weight. Its value is one half of full scale. NEGATIVE FULL SCALE ERROR is the difference between the actual first code transition and its ideal value of 1⁄2 LSB above negative full scale. OFFSET ERROR is the difference between the two input voltages [(VIN+) – (VIN-)] required to cause a transition from code 8191 to 8192. OUTPUT DELAY is the time delay after the falling edge of the clock before the data update is presented at the output pins. PIPELINE DELAY (LATENCY) See CONVERSION LATENCY. POSITIVE FULL SCALE ERROR is the difference between the actual last code transition and its ideal value of 11⁄2 LSB below positive full scale. POWER SUPPLY REJECTION RATIO (PSRR) is a measure of how well the ADC rejects a change in the power supply voltage. PSRR is the ratio of the Full-Scale output of the ADC with the supply at the minimum DC supply limit to the Full-Scale output of the ADC with the supply at the maximum DC supply limit, expressed in dB. SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms value of the sum of all other spectral components below one-half the sampling frequency, not including harmonics or DC. SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the input signal to the rms value of all of the other spectral components below half the clock frequency, including harmonics but excluding d.c. SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the input signal and the peak spurious signal, where a spurious signal is any signal present in the output spectrum that is not present at the input. TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dB, of the rms total of the first nine harmonic levels at the output to the level of the fundamental at the output. THD is calculated as where f1 is the RMS power of the fundamental (output) frequency and f2 through f10 are the RMS power of the first 9 harmonic frequencies in the output spectrum. SECOND HARMONIC DISTORTION (2ND HARM) is the difference expressed in dB, between the RMS power in the input frequency at the output and the power in its 2nd harmonic level at the output. THIRD HARMONIC DISTORTION (3RD HARM) is the difference, expressed in dB, between the RMS power in the input frequency at the output and the power in its 3rd harmonic level at the output. 15 www.national.com ADC14C065/ADC14C080/ADC14C095/ADC14C105 Timing Diagram 20209809 Output Timing Transfer Characteristic 20209810 FIGURE 1. Transfer Characteristic www.national.com 16 ADC14C065/ADC14C080/ADC14C095/ADC14C105 14-Bit, 65/80/95/105 MSPS A/D Converter Physical Dimensions inches (millimeters) unless otherwise noted 32-Lead LLP Package Ordering Numbers: ADC14C065CISQ / ADC14C080CISQ / ADC14C095CISQ / ADC14C105CISQ NS Package Number SQA32A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. BANNED SUBSTANCE COMPLIANCE National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at: www.national.com/quality/green. Lead free products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.