E3SCR11

Oil-resistant, Long-range Photoelectric Sensor with Metal Housing E3S-C CSM_E3S-C_DS_E_9_2 Water- and Oil-resistant Photoelectric Sensor with Metal Housing Used for Longrange Sensing • Excellent resistance against the water and oil. Easy application in locations with oil mist. • Long-range sensing up to 30 m with Through-beam models. • Shock resistance rated at 1,000m/s2. • Product lineup includes metal M12 pre-wired connector models. • NPN/PNP selector switch output. For the most recent information on models that have been certified for safety standards, refer to your OMRON website. Be sure to read Safety Precautions on page 7. Ordering Information Sensors (Refer to Dimensions on page 8.) Sensing method Appearance Red light Connection method Sensing distance Model E3S-CT11 2M Emitter E3S-CT11-L 2M Receiver E3S-CT11-D 2M E3S-CT11-M1J 0.3M Emitter E3S-CT11-L-M1J 0.3M Receiver E3S-CT11-D-M1J 0.3M 30 m E3S-CT61 2M Emitter E3S-CT61-L 2M Receiver E3S-CT61-D 2M E3S-CT61-M1J 0.3M Emitter E3S-CT61-L-M1J 0.3M Receiver E3S-CT61-D-M1J 0.3M Pre-wired Horizontal Pre-wired Connector (M12) Through-beam (Emitter + Receiver) * Vertical Pre-wired Pre-wired Connector (M12) Horizontal Infrared light Pre-wired E3S-CR11 2M Pre-wired Connector (M12) E3S-CR11-M1J 0.3M Retro-reflective 3m Vertical Pre-wired E3S-CR61 2M Pre-wired Connector (M12) E3S-CR61-M1J 0.3M Pre-wired Horizontal Pre-wired Connector (M12) Diffuse-reflective Vertical Pre-wired Pre-wired Connector (M12) 700 mm E3S-CD11 2M 2m E3S-CD12 2M 700 mm E3S-CD11-M1J 0.3M 2m E3S-CD12-M1J 0.3M 700 mm E3S-CD61 2M 2m E3S-CD62 2M 700 mm E3S-CD61-M1J 0.3M 2m E3S-CD62-M1J 0.3M * Through-beam Sensors are normally sold in sets that include both the Emitter and Receiver. 1 E3S-C Accessories (Order Separately) Slits (A Slit is not provided with Through-beam Sensors. Order a Slit separately if required.) (Refer to Dimensions on page 10.) Slit width Sensing distance 0.5 mm × 11 mm 1 mm × 11 mm 2 mm × 11 mm 4 mm × 11 mm 1.8 m 3.5 m 7m 15 m Minimum detectable object (reference value) 0.5-mm dia. 1-mm dia. 2-mm dia. 2.6-mm dia. Model Quantity Remarks 1 set each for Emitter and Receiver (8 Slits total) E39-S61 (Snap-in Long Slit) Can be used with the E3S-CT@1(-M1J) Through-beam Sensor. Refer to page 10. Reflectors (A Reflector is required for each Retro-reflective Sensor.) The E39-R1 Reflector is provided with the Sensor. Order other Reflectors separately if required. (Refer to Dimensions on E39-L/E39-S/E39-R.) Sensing distance Rated value Reference value 3m --- Name Reflectors Small Reflectors Tape Reflectors Model Quantity Remarks E39-R1 1 Provided with the E3S-CR@1 (-M1J) Retro-reflective Sensor. --- 4m E39-R2 1 --- --- 1.5 m E39-R3 1 --- --- 750 mm E39-R4 1 --- --- 700 mm (50 mm)* E39-RS1 1 --- 1,100 mm (100 mm)* E39-RS2 1 --- 1,400 mm (100 mm)* E39-RS3 1 Enables MSR function. Note: 1. If you use any Reflector other than the enclosed Reflector, make sure that the stability indicator lights properly when you set the Sensor. 2. Refer to Reflectors on E39-L/E39-S/E39-R for details. * Values in parentheses indicate the minimum distance required between the Sensor and Reflector. Mounting Brackets Some Mounting Brackets are provided with the Sensor. Order other Mounting Brackets separately if required. (Refer to Dimensions on E39-L/E39-S/E39-R.) Appearance Model Quantity Remarks E39-L102 1 Provided with Horizontal Models. E39-L103 1 Provided with Vertical Models. E39-L85 1 Mounting bracket for changing from E3S@@@@@42/44 to E3S-C Vertical Models. E39-L86 1 Mounting bracket for changing from E3S@@@@@43 to E3S-C Vertical Models. E39-L87 1 --- Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter. 2. Refer to Mounting Brackets on E39-L/F39-L/E39-S/E39-R for details. Sensor I/O Connectors (Sockets on One Cable End) (Models with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) (Refer to Dimensions on XS2.) Cable Appearance Straight Cable type Model 2m XS2F-D421-DC0-F 5m Fire-retardant, robot cable L-shape 2m 5m XS2F-D421-GC0-F 3-wire XS2F-D422-DC0-F XS2F-D422-GC0-F Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter. 2. For details on Sensor I/O Connectors and cables such as vibration-proof robot cables, refer to Introduction to Sensor I/O Connectors/Sensor Controllers. 2 E3S-C Ratings and Specifications Sensing method Model Item Through-beam Retro-reflective (with M.S.R. function) *1 Horizontal E3S-CT11(-M1J) Horizontal E3S-CR11(-M1J) Horizontal E3S-CD11(-M1J) Horizontal E3S-CD12(-M1J) Vertical E3S-CT61(-M1J) Vertical E3S-CR61(-M1J) Vertical E3S-CD61(-M1J) Vertical E3S-CD62(-M1J) Sensing distance 30 m 3 m (when using E39-R1) Standard sensing object Opaque, 15-mm dia. min. Opaque, 75-mm dia. min. Differential travel --- Diffuse reflective 700 mm (300 × 300 mm white paper) 2m (300 × 300 mm white paper) --- 20% max. of sensing distance Directional angle Emitter and Receiver: 3° to15° 3° to 10° Light source (wavelength) Infrared LED (880 nm) Red LED (700 nm) Power supply voltage 10 to 30 VDC including 10% (p.p) ripple Current consumption 50 mA max. (Emitter 25 mA max. Receiver 25 mA max.) Control output Load power supply voltage: 30 VDC max. Load current: 100 mA max. (Residual voltage: NPN output: 1.2 V max., PNP output: 2.0 V max.) Open controller output (NPN/PNP selectable) Light-ON/Dark-ON selectable Protection circuits Power supply reverse polariPower supply reverse polarity protection, Output short-circuit protection, ty circuit protection, Output Mutual interference prevention short-circuit protection Response time Operate or reset: 1 ms max. Sensitivity adjustment One-turn adjuster Ambient illumination (Receiver side) Incandescent lamp: 5,000 lx max. Sunlight: 10,000 lx max. Ambient temperature range Operating: −25°C to 55°C, Storage: −40°C to 70°C (with no icing or condensation) Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation) Insulation resistance 20 MΩ min. (at 500 VDC) Dielectric strength 1,000 VAC, 50/60 Hz for 1 min Vibration resistance Destruction: 10 to 2,000 Hz, 1.5-mm double amplitude or 300 m/s2 for 0.5 hours each in X, Y, and Z directions Shock resistance Destruction: 1,000 m/s2 3 times each in X, Y, and Z directions Degree of protection IEC 60529: IP67 (in-house standards: oil-resistant), NEMA: 6P (indoors only) *2 Connection method Pre-wired (standard cable length: 2 m) or Pre-wired M12 Connector (standard cable length: 0.3 m) Weight (packed state) Approx. 270 g (Pre-wired cable) Approx. 230 g (Pre-wired Connector (M12)) Case Material --Infrared LED (880 nm) 40 mA max. Operate or reset 2 ms max. Two-turn endless adjuster with an indicator Approx. 160 g (Pre-wired cable) Approx. 130 g (Pre-wired Connector (M12)) Approx. 150 g (Pre-wired cable) Approx. 110 g (Pre-wired Connector (M12)) Zinc die-cast Operation PES (polyether sulfone) panel cover Lens Methacrylic resin Mounting Bracket Stainless steel (SUS304) Accessories Mounting Bracket (with screws), Adjustment screwdriver, Instruction manual, and Reflector (only for Retro-reflective Sensors) *1. Refer to MSR function of Technical Guide (Technical version). *2. NEMA: National Electrical Manufactures Association 3 E3S-C Engineering Data (Reference value) Parallel Operating Range Through-beam Retro-reflective E3S-CT@ (-M1J) E3S-CT@ (-M1J) + E39-S61 Slit (Order Separately) E3S-CR@1 (-M1J) + E39-R1 Reflector (Provided) 2 Y 1.5 X 1 800 Distance Y (mm) 2.5 Distance Y (mm) Distance Y (m) Through-beam Slit width: 4 mm 600 Slit width: 2 mm 400 Slit width: 1 mm Y 200 0.5 400 E39-R1 Reflector Y 300 X 200 100 X 0 10 20 30 −0.5 0 40 Distance X (m) −1 4 8 12 0 16 Distance X (m) −200 2 3 4 Distance X (m) −100 −400 −1.5 1 −200 Slit width: 0.5 mm −2 −2.5 −600 −300 −800 −400 Operating Range Diffuse-reflective Distance Y (mm) E3S-CD@@ (-M1J) 50 Sensing object: white paper 40 300 × 300 mm E3S-CD@2 Y 30 X E3S-CD@1 20 10 0 1 2 3 Distance X (m) −10 −20 −30 −40 −50 Excess Gain vs. Set Distance Diffuse-reflective E3S-CT@1 (-M1J) E3S-CR@1 (-M1J) + E39-R1 Reflector (Provided) E3S-CD@@ (-M1J) Excess gain ratio 500 300 100 Excess gain ratio Retro-reflective Excess gain ratio Through-beam 500 Reflector: E39-R1 300 100 500 Sensing object: White paper 300 × 300 mm 300 E3S-CD@1 100 50 50 50 30 30 30 10 10 10 5 5 5 3 3 3 Operating 1 level 0 10 20 30 40 Distance (m) Operating 1 level 0 Operating 1 level 1 2 3 4 Distance (m) 0 E3S-CD@2 1 2 3 Distance (m) 4 E3S-C I/O Circuit Diagrams NPN Output Operation mode Model Operation selector Timing charts Incident light No incident light Light-ON Output circuits Through-beam Model Receivers: Retro-reflective Models, Reflective Models Light indicator ON (Red) OFF ON Output transistor OFF L side (LIGHT ON) Light indicator Stability indicator (Green) (Red) Photoelectric Sensor main circuit Operate Load (e.g. relay) Reset (Between brown A and black D leads) E3S-CT11(-M1J) * E3S-CT61(-M1J) * 1 PNP output transistor 4 Control output ZD 3 OFF Operate Load (e.g. relay) Reset (Between brown A and black D leads) E3S-CD11(-M1J) E3S-CD12(-M1J) E3S-CD61(-M1J) E3S-CD62(-M1J) Connector Pin Arrangement D side (DARK ON) ON Output transistor 0V Blue * Set the NPN or PNP selector to NPN. Light indicator ON (Red) OFF Dark-ON Load current Black * Incident light No incident light E3S-CR11(-M1J) E3S-CR61(-M1J) 10 to 30 VDC Load NPN or PNP output selector NPN output transistor Brown ZD 1 2 4 3 Pin 2 is not used. Through-beam Model Emitters Power indicator (Red) 1 Brown Connector Pin Arrangement 1 Photoelectric Sensor main circuit 10 to 30 VDC 2 4 3 3 Blue Note: Pins 2 and 4 are not used. PNP Output Operation mode Model Light-ON Operation selector Timing charts Incident light No incident light Light indicator ON (Red) OFF ON Output transistor OFF Operate Load (e.g. relay) Reset Output circuits Through-beam Model Receivers: Retro-reflective Models, Reflective Models L side (LIGHT ON) Light indicator Stability indicator (Green) (Red) Photoelectric Sensor main circuit (Between blue C and black D leads) E3S-CT11(-M1J) * E3S-CT61(-M1J) * E3S-CR11(-M1J) E3S-CR61(-M1J) Dark-ON E3S-CD11(-M1J) E3S-CD12(-M1J) E3S-CD61(-M1J) E3S-CD62(-M1J) Brown 10 to 30 VDC ZD * NPN or PNP output selector NPN output transistor Incident light No incident light Light indicator ON (Red) OFF ON Output transistor OFF Operate Load (e.g. relay) Reset 1 PNP output transistor 4 Black Control output Load ZD Blue 3 Load current 0V * Set the NPN or PNP selector to NPN. Connector Pin Arrangement D side (DARK ON) 1 2 4 3 (Between blue C and black D leads) Pin 2 is not used. Through-beam Model Emitters Brown Power indicator (Red) Connector Pin Arrangement 1 1 Photoelectric Sensor main circuit 10 to 30 VDC 2 4 3 Blue Note: Pins 2 and 4 are not used. 3 * Models numbers for Through-beam Sensors (E3S-CT11(-M1J)) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT11-L 2M), the model number of the Receiver, by adding "-D"　 (example: E3S-CT11-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers. Plug (Sensor I/O Connector) Terminal No. 2 3 1 4 1 2 3 4 Brown Classification Blue Black DC XS2F-D421-DC0-A Conductor Connector pin No. Brown 1 --- 2 Refer to Introduction to Sensor I/O Connectors/Sensor Power supply (+V) Controllers for --details. Blue 3 Power supply (0 V) Black 4 Output Application Note: Pin 2 is not used. 5 E3S-C Nomenclature Horizontal Model Vertical Model Operation panel cover Stability indicator (green) S L Light indicator (red) Operation panel cover Stability indicator (green) S PNP Max SENS PNP NPN Sensitivity adjuster D·ON Output selector *1 L·ON E3S-CD12 Operation selector *2 Model number L Light indicator (red) SENS Output selector *1 NPN Min D ON L ON Min Max Sensitivity adjuster Operation selector *2 Note: The sensitivity adjuster on Through-beam and Retro-reflective Models is different. *1. Use the output selector to select the type of output transistor, NPN or PNP. *2. Use the operation selector to select the operation mode. 6 E3S-C Safety Precautions Refer to Warranty and Limitations of Liability. WARNING ● Adjusting Optical Axis of Through-beam Sensor This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings. ● Wiring Cable The E3S-C Through-beam Models incorporates two lenses, one of which will be used as shown in the following illustration. When using a Slit, the Slit must be on the side where the lens to be used is located. Horizontal Model Vertical Model Lens in use. Lens in use. The Slit must be on this side. • The E3S-C uses an oil-resistive cable to ensure oil resistivity. • Do not allow the cable to be bent to a radius of less than 25 mm. Unused lens Unused lens ● Mounting Mounting • When mounting the E3S-C, do not hit the E3S-C with a hammer, or the E3S-C will loose watertightness. • Use M4 screws to mount the E3S-C. The tightening torque of each screw must be 1.18 N·m maximum. Mounting Bracket • When mounting the E3S-C with the mounting bracket so that sensing objects will be in the direction of the mechanical axis, use the optical axis lock holes. • If it is not possible to mount the E3S-C so that the sensing objects will be in the direction the mechanical axis, move the E3S-C upwards, downwards, to the left, or to the right and secure the E3SC in the center of the range where the light indicator will be lit, at which time make sure that the stability indicator is lit. Direct Mounting Mount the E3S-C as shown in the following illustration. Mounting with M4 Screws Two, 4.5 dia. through holes Water Resistance To ensure the water resistance of the E3S-C, tighten the screws of the operation panel cover to a torque of 0.34 N·m to 0.54 N·m. ● Others Oil and Chemical Resistance • Although the E3S-C is oil-resistance, refer to the following table before using the E3S-C in places where oil may be sprayed on the E3S-C. • Tests were carried out with the following oils and it was certified that the E3S-C resists these oils. Oil Lubricating oil Velocite No.3 (manufactured by Exxon Mobil) Water insoluble machining oil Yushiron Oil No. 2 ac (manufactured by Yushiro Chemical Industry Co., Ltd.) M4 M4 hole M4 hole Mounting with M3 Screws Water soluble machining oil Two, M3 M4 hole M3 Optical Axis Adjustment Optical axis Mounting axis Four optical axis lock holes (M4) Kinematic viscosity (mm2/s (cst)) at 40°C PH 2.02 --Less than 10 Yushiroken EC50T-3 (manufactured by Yushiro Chemical Industry Co., Ltd.) 7 to 9.5 Yushiron Lubic HWC68 (manufactured by Yushiro Chemical Industry Co., Ltd.) 7 to 9.9 Griton 1700D (manufactured by Toho Chemical Industry Co., Ltd.) Yushiroken S50N (manufactured by Yushiro Chemical Industry Co., Ltd.) M4 hole Optical Lock Holes By inserting screws into the optical axis lock holes, the Mounting Bracket will be in the direction of the optical axis of the E3S-C. Product name --7 to 9.2 7 to 9.8 Note: 1. The E3S-C maintained a minimum insulation resistance of 100 MΩ after the E3S-C was dipped in all the above oils at a temperature of 50°C for 240 hours. 2. When using the E3S-C in a place where an oil other than the ones listed above is sprayed on the E3S-C, refer to the above kinematic viscosity and ph values. The location may be suitable for the E3S-C if the kinematic viscosity and pH values of the oil are close to the above kinematic viscosity and pH values, but make sure that the oil does not contain any additive that may have a negative influence on the E3S-C. 7 E3S-C (Unit: mm) Dimensions Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified. Sensors Through-beam (Horizontal) E3S-CT11(-M1J) Pre-wired Connector (-M1J) 4-dia. vinyl-insulated round cable Standard length: 300 mm With Mounting Bracket Attached 18.5 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm2 (AWG 24), Insulator diameter: 1.2 mm), Standard length: 2 m *3 M3 × 5 50 M12 × 1 *2 Light indicator (red) 20 20.4 Mounting Holes 22.2 Stability indicator (green) Emitter: E3S-CT@@-L Receiver: E3S-CT@@-D Two, M4 20 4.2 9.2 25.4 4.2 Lens (17 × 11) 6.2 Optical axis 8.3 Stainless steel (SUS304) 38.2 2.2 4 23 29.5 18 17.3 9.3 A*1 Two, M4 1.5 20.8 25.4 *1. The Mounting Bracket can be attached to side A. *2. The Emitters for Through-beam Sensors only have the power indicator (red). *3. The Emitter cable is 4-dia.vinyl-insulated round cable with 2 conductors (conductor cross section: 0.3 mm2, insulator diameter: 1.3 mm) and a standard length of 2 m. Note: Models numbers for Through-beam Sensors (E3S-CT11(-M1J)) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT11-L 2M), the model number of the Receiver, by adding "-D"　 (example: E3S-CT11-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers. 8 E3S-C Through-beam (Vertical) E3S-CT61(-MJ) Pre-wired Connector (-M1J) 4-dia. vinyl-insulated round cable Standard length: 300 mm With Mounting Bracket Attached M12 × 1 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm2 (AWG24), Insulator diameter: 1.2 mm), Standard length: 2 m *3 57 Optical axis 15.8 7.4 Optical axis 20 20.4 Mounting Holes 22.2 Lens (17 × 11) Two, M4 4.2 20 9.2 25.4 4.2 4.2 Stainless steel (SUS304) 12.9 12.9 25.4 31 Stability indicator (green) 7.2 Light indicator (red)*2 43.8 2.2 5.8 20.2 23 32.2 A*1 M3 × 5 12 Two, M4 23.2 1.5 *1. The Mounting Bracket can be attached to side A. *2. The Emitters for Through-beam Sensors only have the power indicator (red). *3. The Emitter cable is 4-dia.vinyl-insulated round cable with 2 conductors (conductor cross section: 0.3 mm2, insulator diameter: 1.3 mm) and a standard length of 2 m. Retro-/Diffuse-reflective (Horizontal) E3S-CR11(-M1J) E3S-CD11(-M1J) E3S-CD12(-M1J) Pre-wired Connector (-M1J) 4-dia. vinyl-insulated round cable Standard length: 300 mm With Mounting Bracket Attached 18.5 50 Light indicator (red) M3 × 5 M12 × 1 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm2 (AWG24), Insulator diameter: 1.2 mm), Standard length: 2 m 20 20.4 Mounting Holes 22.2 Stability indicator (green) Two, M4 20 4.2 9.2 25.4 4.2 Lens (17 × 11) 6.2 Receiver 8.3 Stainless steel (SUS304) 38.2 2.2 23 4 9 29.5 1 18 17.3 9.3 A* Optical axis Emitter Two, M4 1.5 20.8 25.4 *The Mounting Bracket can be attached to side A. Note: Models numbers for Through-beam Sensors (E3S-CT61(-M1J)) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT61-L 2M), the model number of the Receiver, by adding "-D"　 (example: E3S-CT61-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers. 9 E3S-C Retro-/Diffuse-reflective (Vertical) E3S-CR61(-M1J) E3S-CD61(-M1J) E3S-CD62(-M1J) Pre-wired Connector (-M1J) 4-dia. vinyl-insulated round cable Standard length: 300 mm With Mounting Bracket Attached M12 × 1 57 Receiver 5 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm2 (AWG24), Insulator diameter: 1.2 mm), Standard length: 2 m 9 2.4 20.8 Emitter Optical axis 20 20.4 Mounting Holes 22.2 Two, M4 Lens (17 × 11) 4.2 9.2 20 25.4 4.2 4.2 12.9 12.9 Stainless steel (SUS304) 25.4 31 Stability indicator (green) 7.2 Light indicator (red) 43.8 2.2 5.8 20.2 23 32.2 A*1 M3 × 5 12 Two, M4 23.2 *The Mounting Bracket can be attached to side A. 1.5 Accessories (Order Separately) Snap-in Long Slit (For Through-beam Models) E39-S61 1 A 0.2 11 6.2 11.8 20 3.8 6.5 20.1 Dimension A (mm) 0.5 1 2 4 Material Stainless steel Quantity 1 set each for Emitter/Receiver (8 Slits total) Reflectors Refer to E39-L/E39-S/E39-R for details. Mounting Brackets Refer to E39-L/E39-S/E39-R for details. 10 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2015.4 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2015 All Right Reserved.