F3ET2-018-150

Discrete Output Light Grid in Robust Aluminum Housing F3ET2 The F3ET2 light grids provide reliable area monitoring in robust housing. The M12, 5-pin connectors and optical synchronization between transmitter and receiver allow for fast and simple installation without special requirements. • Optical synchronization for reliable operation without additional wiring • Robust aluminum housing • NPN/PNP and Light-on / Dark-on selectable • Brackets included with Light Grids Ordering Information Sensor Type Detection Area (mm) Throughbeam 150 300 450 600 900 1200 1500 1800 2100 * Pitch 5 mm 18 mm 5 mm 18 mm 5 mm 18 mm 5 mm 18 mm 5 mm 18 mm 5 mm 18 mm 5 mm 18 mm 5 mm 18 mm 18 mm Sensing Distance 3m 15 m 3m 15 m 3m 15 m 3m 15 m 3m 15 m 3m 15 m 3m 15 m 3m 15 m 15 m Beams 30 8 60 16 90 24 120 32 180 48 240 64 300 80 360 96 112 Connection Method Output* PNP/NPN 5 pin Model F3ET2-005-150 F3ET2-018-150 F3ET2-005-300 F3ET2-018-300 F3ET2-005-450 F3ET2-018-450 F3ET2-005-600 F3ET2-018-600 F3ET2-005-900 F3ET2-018-900 F3ET2-005-1200 F3ET2-018-1200 F3ET2-005-1500 F3ET2-018-1500 F3ET2-005-1800 F3ET2-005-1800 F3ET2-018-2100 Light-ON / Dark-ON selectable F3ET2 Discrete Output Light Grid 1 Rating/Specifications Item Sensing distance Vertical detection area Minimum detectable object size Beam axis pitch Response time Power-on delay Light source (wavelength) Power supply voltage Current consumption Ambient temperature Storage temperature Degree of protection Protective circuits Material Case Cover Through-beam F3ET2-005_ 0 to 3 m F3ET2-018_ 0 to 15 m 0 to: 150, 300, 450, 600, 900, 1200, 1500, 1800 mm 0 to: 150, 300, 450, 600, 900, 1200, 1500, 1800, 2100 mm 10 mm 30 mm 5 mm 18 mm 4 ms + 80 µs × number of beams 1 s max Infrared LED (880 nm) 24 VDC ±20% 150 mA max –10 to 55°C –25 to 70°C IEC 60529 IP65 Reverse polarity protection, output short-circuit protection Aluminum Polycarbonate Cable connectors For pin arrangement and wire connection refer to Output Circuits. Type Features M12 5 wires 2 Material Nut CuZn Cable PVC 2 m PUR 2 m PVC 5 m PUR 5 m Model Straight XS2F-M12PVC5S2M XS2F-M12PUR5S2M XS2F-M12PVC5S5M XS2F-M12PUR5S5M Angled XS2F-M12PVC5A2M XS2F-M12PUR5A2M XS2F-M12PVC5A5M XS2F-M12PUR5A5M F3ET2 Discrete Output Light Grid Output circuits Please connect the light grid as described below: Variable Power Supply Earth Ground +24 VDC 0 VDC Connector PIN assignment - Receiver RECEIVER Br Wh BL Internal wiring Type Bk Gr M12 n4 pole Pin Color Signal name 1 2 3 4 5 +Vs not used 0V PNP/NPN output not used Brown White Blue Black Gray Connector PIN assignment - Transmitter TRANSMITTER Br Wh BL Internal wiring Type Bk M12 n4 pole Pin Color Signal name 1 2 3 4 +Vs not used 0V Not used Brown White Blue Black Dimensions Model L: Total length E: Detection zone E A: Dead zone without detection capability L 37 48 10.5 Total length L (mm) 218 217 277 364 536 511 695 658 1013 952 1331 1246 1649 1540 1967 1834 2128 A 22.75 6.5 4.5 F3ET2-005-150 F3ET2-018-150 F3ET2-005-300 F3ET2-018-300 F3ET2-005-450 F3ET2-018-450 F3ET2-005-600 F3ET2-018-600 F3ET2-005-900 F3ET2-018-900 F3ET2-005-1200 F3ET2-018-1200 F3ET2-005-1500 F3ET2-018-1500 F3ET2-005-1800 F3ET2-018-1800 F3ET2-018-2100 Detection zone E (mm) 159 147 318 294 477 441 636 588 954 882 1272 1176 1590 1470 1908 1764 2058 All dimensions shown are in mm F3ET2 Discrete Output Light Grid 3 Operation The F3ET light grid features optical synchronization. This function is provided by the upper beam located on the opposite side of the connector (see illustration on the right). During operation this beam must always be kept free (unblocked). Otherwise it will result in a longer response frequency of the light grid. SYNCHRONISM S D S: Sensing area D: Beam axis pitch Indicator LEDs For functions of indicator LEDs please refer to the tables below: Status of Receiver is displayed by 5 LEDs: Color POWER Disposition of indicator Name of indicator Color Green POWER Green RUN Yellow STATUS 1 Yellow FREE Green RANGE Green BREAK Red STATUS Yellow STATUS 2 RX Name of indicator POWER STATUS 1 RANGE POWER RUN FREE BREAK STATUS Disposition of indicator Status of Transmitter is displayed by 5 LEDs: TX Not used STATUS 2 Yellow Selector Switches Operation mode and distance setting can be changed by selector switches. To access selector switches, unscrew the end cap of the receiver unit: OFF ON OFF ON Transmitter Dip-SW 1, 2, 3, 4, 7, 8 5 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Receiver Status OFF ON OFF ON Function Not USED Not USED FAR (Default) NEAR Dip-SW 1, 4, 5, 7, 8 2 3 Status OFF ON OFF ON OFF ON Function Not USED Not USED PNP operation (Default) NPN operation Dark on (Default) Light on Note: Selector setting must only be carried out when the receiver is NOT connected to the power supply. There are two lines of dip switches in each transmitter and receiver. The settings must be done for both lines. 4 F3ET2 Discrete Output Light Grid Mounting Mounting accessories Mechanical Mounting The F3ET2 system is mechanically installed by using the Tslots on the two sides or the back-side of the housing. Use the movable bolts, washers, spacers and nuts to attach the mounting brackets as shown in the picture Please mount the light grids in proper alignment as shown in the pictures below by using the brackets provided with the light grids. ID 1 2 3 4 5 Description M6 bolt bracket M6 washer M6 spacer M6 nut Note: Shipments contain a different quantity of brackets, depending on the length of the light grid. Longer light grids contain a higher number of brackets, following the rule of one bracket every 400 mm. OK NG NG If several light grids are installed close to each other, interference of the light grids must be avoided. In this case the assembly should be carried out as follows: TX RX RX TX Additional mounting rigidity It is recommended that the distance between the mounting brackets is 400 mm or less for optimum performance of the F3ET2 system. F3ET2 Discrete Output Light Grid 5 Precautions ⚠ WARNING The F3ET multi-beam photoelectric sensor is not a safety component for ensuring the safety of people which is defined in EC directive (2006/42/EC) or by any other regulations or standards. Power Supply Voltage and Output Load Power Supply Voltage Do not connect an AC power supply to the Sensor. If AC power (100 VAC or more) is supplied to the Sensor, it may be damaged, explode or burn. Make sure that the power supply to the Sensor is within the rated voltage range. If a voltage exceeding the rated voltage range is supplied to the Sensor, it may explode or burn. Operating Environment Do not use the sensor in locations with explosive or flammable gas. Make sure that the product is operated in accordance with IP65 standards. Do not subject the sensor to excessive shock when mounting. When you use the sensor in the vicinity of an inverter motor, be sure to connect the protective earth ground wire of the motor to earth. Failure to ground the motor may result in malfunction of the sensor. Mounting the Sensor Do not strike the sensor with a hammer or any other tool during the installation of the Sensor. Cleaning Never use paint thinners or other organic solvents to clean the surface of the product M12 Connector Always turn OFF the power supply to the sensor before connecting or disconnecting the metal connector. Hold the connector cover to connect or disconnect it. Secure the connector cover by hand. Do not use pliers; otherwise the connector may be damaged. If the connector is not connected securely, it may be disconnected by vibration or the proper degree of protection of the sensor may not be maintained. OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Schaumburg, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com OMRON CANADA, INC. • HEAD OFFICE Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com OMRON ARGENTINA • SALES OFFICE Cono Sur • 54.11.4783.5300 OMRON ELECTRONICS DE MEXICO • HEAD OFFICE México DF • 52.55.59.01.43.00 • 001.800.556.6766 • mela@omron.com OMRON CHILE • SALES OFFICE Santiago • 56.9.9917.3920 OMRON ELECTRONICS DE MEXICO • SALES OFFICE Apodaca, N.L. • 52.81.11.56.99.20 • 001.800.556.6766 • mela@omron.com OTHER OMRON LATIN AMERICA SALES 54.11.4783.5300 OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • Tel: +31 (0) 23 568 13 00 • Fax: +31 (0) 23 568 13 88 • www.industrial.omron.eu P73I-E-01 Note: Specifications are subject to change. © 2012 Omron Electronics LLC Printed in U.S.A.