TL-W1R5MB16M

Sensing distance 20 mm Supply voltage 5 mm 1.5mm 3 mm 5 mm Output 12 to 24 VDC 100/200 mA NPN or PNP Inductive Proximity Sensor TL-W/WM Space Saving Flat Proximity Switch Space-saving, low-profile rigid aluminum die-cast housing (TL-W5E/F). All models provided with an operation indicator. Mounting possible from either the front or rear of the housing. Protected to endure water and oil splashes (conforms to IEC IP67). DC 2-wire models (TL-W5MD1/-W5MD2) provide easy wiring. Ordering Information DC 2-wire Sensing head Sensing distance Output NPN NO Non-shielded 5 mm TL-W5MD1 PNP NC TL-W5MD2 NO --- NC --- DC 3-wire Sensing head Sensing distance Output NPN NO PNP NC NO NC Shielded 5 mm TL-W5E1 TL-W5E2 TL-W5F1 TL-W5F2 Non-shielded 1.5 mm TL-W1R5MC1 --- TL-W1R5MB1 --- 3 mm TL-W3MC1 TL-W3MC2 TL-W3MB1 TL-W3MB2 5 mm TL-W5MC1 TL-W5MC2 TL-W5MB1 --- 20 mm TL-W20ME1 TL-W20ME2 --- --- 1 TL-W/WM TL-W/WM Application Examples Position of Workpiece Specifications Ratings/Characteristics DC 2-wire Item TL-W5MD Sensing distance 5 mm ±10% Supply voltage (operating voltage range) 12 to 24 VDC (10 to 30 VDC) Current consumption (leakage current) 0.8 mA max. Sensing object Magnetic metals (refer to “Engineering Data” for non-magnetic metals) Setting distance (standard sensing object) 0 to 4 mm (iron, 18 x 18 x 1 mm) Differential travel 10% max. of sensing distance Response frequency (see note) 0.5 kHz Operating mode (for detecting sensing objects) D1 models: D2 models: Control output (switching capacity) 3 to 100 mA DC Circuit protection Load short-circuit protection Indicator D1 models: D2 models: Ambient temperature Operating: –25°C to 70°C (with no icing) Ambient humidity Operating: 35% to 95% Temperature influence ±10% max. of sensing distance at 23°C in temperature range of –25°C to 70°C Voltage influence ±2.5% max. of sensing distance in rated voltage range ±15% Residual voltage 3.3 V max. (with 100 mA load current and 2-m cable) Insulation resistance 50 MΩ min. (at 500 VDC) between current carry parts and case Dielectric strength 1,000 VAC for 1 min between current carry parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hrs each in X, Y, and Z directions Shock resistance Destruction: 500 m/s2 (approx. 50G) for 3 times each in X, Y, and Z directions Enclosure ratings IEC IP67 (JEM IP67G (water-tight, oil-tight) Weight (with 2-m cable) Approx. 45 g Material Heat-resistive ABS resin Case Load ON Load OFF Operation indicator (red LED), operation set indicator (green LED) Operation indicator (red LED) Sensing surface Note: 2 The response frequency in the table is a mean value obtained under the following conditions. Location of each standard sensing object: At a distance half as long as the sensing distance of the sensor. Distance between any two adjacent standard sensing objects: Twice as wide as the width of the standard sensing object. TL-W/WM TL-W/WM DC 3-wire Item TL-W1R5M TL-W3M 3 mm ±10% TL-W5M TL-W5 TL-W20M Sensing distance 1.5 mm ±10% Supply voltage (operating voltage range) 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 20% max. 12 to 24 VDC (10 to 30 VDC) Current consumption (leakage current) 15 mA max. at 24 VDC (no-load) 15 mA max. at 24 VDC (no-load) 8 mA at 12 VDC, 15 mA at 24 VDC Sensing object Magnetic metals (Non-magnetic metals can be detected if they are located close to the sensor. Refer to “Engineering Data” for details) Setting distance (standard sensing object) 0 to 1.2 mm (iron, 8 x 8 x 1 mm) Differential travel 10% max. of sensing distance Response frequency (see note) 1 kHz Operating mode (for detecting sensing objects) Load ON Control output (switching capacity) NPN or PNP open collector, 100 mA max. Circuit protection Reverse connection protection Ambient temperature Operating: –25°C to 70°C (with no icing) Ambient humidity Operating: 35% to 95% Temperature influence ±10% max. of sensing distance at 23°C in temperature range of –25°C to 70°C Voltage influence ±2.5% max. of sensing distance in rated voltage range ±10% ±2.5% max. of sensing distance in rated voltage range ±20% ±2.5% max. of sensing distance in rated voltage range ±10% Residual voltage 1.0 V max. (with 100 mA load current and 2-m cable) 1.0 V max. (with 50 mA load current and 2-m cable) 2.0 V max. (with 200 mA load current and 2-m cable) Insulation resistance 50 MΩ min. (at 500 VDC) between current carry parts and case Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between current carry parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hrs each in X, Y, and Z directions Shock resistance Destruction: 500 m/s2 (approx. 50G) for 3 times each in X, Y, and Z directions Enclosure ratings IEC IP67 (JEM IP67G (water-tight, oil-tight) Weight (with 2-m cable) Approx. 30 g Material Case ABS resin Sensing surface ABS resin 0 to 2.4 mm (iron, 12 x 12 x 1 mm) 600 Hz min. 5 mm ±10% 10 mA max. 20 mm ±10% 0 to 4 mm (iron, 18 x 18 x 1 mm) 0 to 16 mm (iron, 50 x 50 x 1 mm) 1% to 15% of sensing distance 500 Hz min. 300 Hz min. E1 models: E2 models: F1 models: F2 models: NPN or PNP open collector, 50 mA max. at 12 VDC, 100 mA max. at 24 VDC 40 Hz Output signal low, load ON Output signal high, load OFF Output signal high, load ON Output signal low, load OFF 200 mA max. 100 mA max. at 12 VDC, 200 mA max. at 24 VDC --- Approx. 45 g 1.0 V max. (with 200 mA load current and 2-m cable) Destruction: 500 m/s2 (approx. 50G) for 10 times each in X, Y, and Z directions Approx. 70 g Approx. 180 g ADC (Al die-cast) Heat-resistive ABS 3 TL-W/WM TL-W/WM Engineering Data Operating Range (Typical) Sensing object Sensing distance X (mm) Sensing object: Iron, 8 x 8 x 1 mm Sensing object: Iron, 12 x 12 x 1 mm X Y Sensing object Sensing object: Iron, 18 x 18 x 1 mm Y Sensing object X Sensing head Y (mm) TL-W5 Sensing object: Iron, 18 x 18 x 1 mm TL-W5M Sensing distance x (mm) TL-W3M Sensing distance X (mm) TL-W1R5M Sensing head Y (mm) Sensing head TL-W20M Sensing distance X (mm) X (mm) Sensing object: Iron, 15 x 15 x 1 mm X t = 1 mm Y X Y Sensing object Sensing object Sensing head 4 Y (mm) Sensing head Y (mm) Y (mm) TL-W/WM TL-W/WM Sensing Distance vs. Size and Material of Sensing Object (Typical) TL-W3M TL-W1R5M TL-W5M Stainless steel (SUS304) Brass Copper Iron Stainless steel (SUS304) Brass Aluminum Copper Sensing distance (mm) Iron Sensing distance (mm) Sensing distance (mm) Object: Iron t = 1 mm Operate Release d X Sensing object Aluminum Object diameter d (mm) Object diameter d (mm) TL-W5 Object diameter d (mm) TL-W20M Iron Iron Stainless steel (SUS 304) Brass Aluminum Object diameter d (mm) Sensing distance (mm) Sensing distance (mm) d Sensing object X Stainless steel (SUS304) Copper Aluminum Object diameter d (mm) 5 TL-W/WM TL-W/WM Operation Output Circuits DC 2-wire TL-W5MDj Brown Load Brown Load +V Blue Main circuit Brown Blue 0V Blue Load Note: The load can be connected as shown in the above diagram. DC 3-wire TL-W1R5MC1 TL-W3MCj TL-W5MCj TL-W5Ej TL-W20MEj TL-W5Fj Brown Brown +V 100 Ω Black (see note) Main circuit Load 4.7 kΩ Main circuit Output Blue Note: TL-W1R5MB1 TL-W3MBj TL-W5MB1 Brown +V Black Load 100 Ω 6 Load Main circuit Output (see note 2) 4.7 kΩ 0V Maximum load current: 100 mA Main circuit Black (see note 1) Blue 0V Note: 2.2 Ω Blue 0V Brown +V 100 Ω +V Black (see note 1) 2.2 Ω Output (see note 2) Load 100 Ω 0V Blue 1. Maximum load current: 200 mA 2. Current flows in this direction if the circuit incorporates the transistor. TL-W/WM TL-W/WM Timing Chart DC 2-wire NO Model NC Model Setting position Unstable sensing Stable zone Non-sensing zone sensing zone Proximity Sensor Non-sensing zone Sensing zone Proximity Sensor Sensing object Sensing object Rated sensing distance Lit Not lit Lit Rated sensing distance Green indicator Red indicator Lit ON OFF Control output ON Red indicator Not lit Not lit OFF Control output DC 3-wire TL-W1R5Mj1 TL-W3Mj TL-W5Mj TL-W5j TL-W20MEj Sensing object Yes No Load (between brown and black) Operate Release Sensing object Yes No Output transistor (load) ON OFF Output voltage (between blue and black) H L Operation indicator Lit Not lit Operation indicator Lit Not lit TL-W5Fj Sensing object Yes No Load (between blue and black) Operate Release Output voltage (between blue and black) H L Operation indicator Lit Not lit 7 TL-W/WM TL-W/WM Dimensions Note: All units are in millimeters unless otherwise indicated. TL-W1R5Mj1 Operation indicator Mounting Bracket (Attachment) (See note) Mounting hole for M3 pan-head screw Sensing surface (see note) 6 dia. Note: 3.2 dia. Round vinyl-insulated cable (2.9 dia., 0.12 dia. x 12, 3 cores) Standard length: 2 m (oil-tight) Operation indicator Note: Mounting dimensions: 17±0.2 Operation indicator TL-W3Mjj 27 17±0.2 5±0.2 Mounting Bracket (Attachment) 3 Operation indicator (see note) 10 Sensing surface 8 (See note) 9 Mounting hole for M3 pan-head screw 90° Note: 6 dia. 6.0 3.2 dia. Round vinyl-insulated cable (2.9 dia., 0.12 dia. x 12, 3 cores) Standard length: 2 m (oil-tight) Operation indicator TL-W5Mjj TL-W5MDj 8.5 18 4.5 TL-W5MDj: Round vinyl-insulated cable (4 dia., 0.12 dia. x 27, 2 cores) Standard length: 2 m (oil-tight) 18 12±0.1 3.5 5 Operation indicator 10 8 Mounting dimensions: 17±0.2 TL-W5Mjj: Round vinyl-insulated cable (4 dia., 0.12 dia. x 18, 3 cores) Standard length: 2 m (oil-tight) 30.5 Sensing surface Note: Two, 3.5 x 5 mounting holes 12.5 6.5 7.5 8 TL-W/WM TL-W/WM TL-W5Ej TL-W5Fj 4.2 dia. 3 3 Mounting Holes 10 10 44 7.2 7.2 dia. dia. 10 10 88 Round vinyl-insulated cable Round vinyl-insulated cable (4 dia., 0.12 x18 (4 dia., 0.12 dia.dia. x 18, 3 cores) 3 cores) Standard cable length: 2 m 15±0.2 0 24.9 –0.4 15 Two, 4.5 dia. holes Approx. 2 50 50 Sending surface Operation indicator TL-W20MEj Sensing surface 40 30±0.1 18 5 27±0.1 5 Operation indicator 6 Two, 5.5 dia. mounting holes 23 18 1 53 1.5 Round vinyl-insulated cable (6 dia., 0.12 dia. x 45, 3 cores) Standard length: 2 m 9 TL-W/WM TL-W/WM Precautions Effects of Surrounding Metals Mutual Interference Provide a minimum distance as shown in the table below between the TL-W and the surrounding metals to prevent the TL-W from being induced by the metals and malfunctioning or being affected by the heat radiated by the metals. Be sure to space the two sensors at a distance greater than that shown in the table to prevent mutual interference. ȏ Model m n TL-W1R5Mj1 2 mm 0 mm 8 mm TL-W3M 3 mm 0 mm 12 mm TL-W5MD TL-W5MC/MB TL-W20ME TL-W5E/F 5 mm 5 mm 25 mm 0 mm 0 mm 20 mm 0 mm 20 mm 16 mm 100 mm 0 mm 20 mm ÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉ ÉÉÉÉÉ ÉÉÉÉÉÉÉÉ ÉÉÉÉÉ ÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉ Model 25 (8) mm TL-W3M 90 (60) mm 30 (10) mm TL-W5MD 120 (80) mm 60 (30) mm TL-W5MC/MB 120 (80) mm 60 (30) mm TL-W20ME 200 (100) mm 200 (100) mm TL-W5E/F 50 mm 35 mm Note: The above values in parentheses are applicable when using two sensors with different frequencies. A Sensing surface Metals on Both Sides and in front of the Sensor B 75 (50) mm m Metal on a Single Side (not exceeding the height of the sensor head) A TL-W1R5Mj1 B Proximity switch ȏ Sensing surface n ȏ Proximity switch 10 Mounting Use M3 flat-head screws to mount the TL-W1R5Mj1 and TL-W3Mj1. The resin cover should be tightened to 10 kgf S cm (0.98 N S m) maximum. TL-W/WM TL-W/WM ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. E221-E1-2 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Systems Components Division H.Q. 28th Fl., Crystal Tower Bldg. 1-2-27, Shiromi, Chuo-ku, Osaka 540 Japan Phone: 06-949-6012 Fax: 06-949-6021 12 11 Printed in Japan 0196-1.5M (1291) a