CAT4106AGEVB

CAT4106AGEVB CAT4106 LED Driver Evaluation Board User's Manual http://onsemi.com EVAL BOARD USER’S MANUAL Introduction Operation Procedure This document describes the CAT4106AGEVB evaluation board for the CAT4106 quad-channel DC/DC boost LED driver. The major operating characteristics of the CAT4106 can be measured with this board. The CAT4106 DC/DC converter is capable of driving up to 4 strings of LEDs with tight matching. This device is designed to drive LED strings up to 36 V. The LED brightness is set by a single resistor from the RSET pin to GND and PWM dimming is available via the EN/PWM pin. Additional information can be found in the CAT4106 data sheet. The CAT4106AGEVB board contains one CAT4106 in a typical application circuit. The board can be powered in two different ways. With the J1 jumper in place a single high voltage supply (6 V to 24 V) can be applied between VL and GND. A circuit on board will generate a lower, regulated voltage for the VIN pin (6.2 V – VGS of transistor M1). VIN can also be powered separately by removing the J1 jumper and applying a second voltage to the VIN test point. The voltage at VIN should not exceed 6.0 V. VFMAX and VFMIN are set by potentiometers R4 and R6 respectively. The VFMIN potentiometer is located closest to the VIN test point. These can be used to set the maximum and minimum allowable forward voltages for any given LED string. For the CAT4106AGEVB, the settings for these potentiometers are calculated as follows: R4 + 69.8 kW R6 + 60 kW October, 2011 − Rev. 1 FMAX ǒV1.2 V * 1Ǔ * 100 kW FMIN (eq. 1) (eq. 2) Any open LED conditions will trigger a fault condition. Any short LED conditions will only trigger a fault condition during power-up. A red LED will turn on when a fault condition takes place. The LED current is set by potentiometer R13 which is labeled RSET on the CAT4106AGEVB. The anode end of each LED string should be connected to VOUT and the cathode ends can be connected at the available header connectors J5 and J6. Placing jumpers on J5 and J6 headers allows to short two or more LED channels together. EN or PWM input signals can be connected at the EN/PWM test point. The voltage at EN/PWM should not exceed 6.0 V. The CAT4106 can support PWM frequencies up to 2 kHz. Figure 1. CAT4106AGEVB Board © Semiconductor Components Industries, LLC, 2011 ǒV1.2 V * 1Ǔ * 100 kW 1 Publication Order Number: EVBUM2024/D CAT4106AGEVB D L VL 47 mH R9 100 W C2 4.7 mF M1 VIN 1 J1 SW R8 60 kW GND VOUT U1 2 C3 10 mF 6 SW EN/PWM VIN 9 EN/PWM 7 C1 1 mF EN/PWM R14 100 kW Z1 6.2 V 13 R2 R1 649 W 10 28 kW 5 VIN EN/PWM VFMIN RSET LED1 CTRL LED2 FB LED3 LED4 R13 20 kW R3 28 kW CAT4106 R10 FAULT VFMAX GND FAULT PGND 2 4 VIN 1 kW R4 2.2 MW R6 2.2 MW SW SW R11 100 kW R12 100 kW R5 69.8 kW R7 60 kW 12 11 1 LED1 16 LED2 15 LED3 14 LED4 3 FAULT J5 LED1 1 1 LED2 2 2 LED3 3 3 LED4 4 4 J6 LED1 LED2 LED3 LED4 Figure 2. CAT4106AGEVB Board Schematic Table 1. BILL OF MATERIALS Name Manufacturer Description U1 ON Semiconductor 4-Channel Boost LED Driver, 4 mm x 4 mm TQFN CAT4106 Part Number Units 1 C1 AVX Ceramic Capacitor 1.0 mF/10 V, 10%, X5R, 0603 0603ZD105KAT2A 1 C2 AVX Ceramic Capacitor 4.7 mF/25 V, 10%, X5R, 1206 12063D475KAT2A 1 C3 Taiyo Yuden Ceramic Capacitor 10 mF/ 35 V, 10%, X5R, 1210 GMK325BJ106KN-T 1 R1 Yageo SMT Resistor 0.1 W, 649 W, 0603 RC0603FR-07649RL 1 R2, R3 Yageo SMT Resistor, 0.1 W, 28 kW, 0603 RC0603FR-0728KL 2 R4, R6 Vishay Trimmer Potentiometer, 2.2 MW T93YB225K 2 R5 Yageo SMT Resistor, 0.1 W, 69.8 kW, 0603 RC0603FR-0769K8L 1 R7, R8 Yageo SMT Resistor, 0.1 W, 60.4 kW, 0603 RC0603FR-0760K4L 2 R9 Yageo SMT Resistor, 0.1 W, 100 W, 0603 RC0603FR-07100RL 1 R10 Tyco SMT Resistor, 0.1 W, 1 kW, 0603 RC0603FR-071KL 1 R11, R12, R14 Yageo SMT Resistor, 0.1 W, 100 kW, 0603 RC0603FR-07100KL 3 R13 Vishay Trimmer Potentiometer, 20 kW T73YE-20K-ND 1 L Coiltronics Inductor 47 mH, 1.08 A DR73-470-R 1 D NXP Schottky Diode, 60 V/1 A PMEG6010CEJ T/R 1 M1 ON Semiconductor N-Channel MOSFET, 60 V/115 mA 2N7002L 1 Z1 ON Semiconductor Zener Diode, 6.2 V MM3Z6V2 1 J1, J2 Tyco 2 Pin Header Connector 0.1” Pitch 640452-2 2 Tyco J5, J6 4 Pin Header Connector 0.1” Pitch 640452-4 2 Mil-Max Pin Receptacle (Test Points) #0149-0-15-01-30-14-04-0 (or equiv) 6 LiteOn SMT Red LED LTST-T970KRKT 1 http://onsemi.com 2 onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. The evaluation board/kit (research and development board/kit) (hereinafter the “board”) is not a finished product and is not available for sale to consumers. The board is only intended for research, development, demonstration and evaluation purposes and will only be used in laboratory/development areas by persons with an engineering/technical training and familiar with the risks associated with handling electrical/mechanical components, systems and subsystems. This person assumes full responsibility/liability for proper and safe handling. Any other use, resale or redistribution for any other purpose is strictly prohibited. THE BOARD IS PROVIDED BY ONSEMI TO YOU “AS IS” AND WITHOUT ANY REPRESENTATIONS OR WARRANTIES WHATSOEVER. WITHOUT LIMITING THE FOREGOING, ONSEMI (AND ITS LICENSORS/SUPPLIERS) HEREBY DISCLAIMS ANY AND ALL REPRESENTATIONS AND WARRANTIES IN RELATION TO THE BOARD, ANY MODIFICATIONS, OR THIS AGREEMENT, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING WITHOUT LIMITATION ANY AND ALL REPRESENTATIONS AND WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, NON−INFRINGEMENT, AND THOSE ARISING FROM A COURSE OF DEALING, TRADE USAGE, TRADE CUSTOM OR TRADE PRACTICE. onsemi reserves the right to make changes without further notice to any board. You are responsible for determining whether the board will be suitable for your intended use or application or will achieve your intended results. Prior to using or distributing any systems that have been evaluated, designed or tested using the board, you agree to test and validate your design to confirm the functionality for your application. Any technical, applications or design information or advice, quality characterization, reliability data or other services provided by onsemi shall not constitute any representation or warranty by onsemi, and no additional obligations or liabilities shall arise from onsemi having provided such information or services. onsemi products including the boards are not designed, intended, or authorized for use in life support systems, or any FDA Class 3 medical devices or medical devices with a similar or equivalent classification in a foreign jurisdiction, or any devices intended for implantation in the human body. You agree to indemnify, defend and hold harmless onsemi, its directors, officers, employees, representatives, agents, subsidiaries, affiliates, distributors, and assigns, against any and all liabilities, losses, costs, damages, judgments, and expenses, arising out of any claim, demand, investigation, lawsuit, regulatory action or cause of action arising out of or associated with any unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of any products and/or the board. This evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and may not meet the technical requirements of these or other related directives. FCC WARNING – This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation purposes only and is not considered by onsemi to be a finished end product fit for general consumer use. It may generate, use, or radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this equipment may cause interference with radio communications, in which case the user shall be responsible, at its expense, to take whatever measures may be required to correct this interference. onsemi does not convey any license under its patent rights nor the rights of others. LIMITATIONS OF LIABILITY: onsemi shall not be liable for any special, consequential, incidental, indirect or punitive damages, including, but not limited to the costs of requalification, delay, loss of profits or goodwill, arising out of or in connection with the board, even if onsemi is advised of the possibility of such damages. In no event shall onsemi’s aggregate liability from any obligation arising out of or in connection with the board, under any theory of liability, exceed the purchase price paid for the board, if any. The board is provided to you subject to the license and other terms per onsemi’s standard terms and conditions of sale. For more information and documentation, please visit www.onsemi.com. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 1 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative