CM1430-08DE

ON Semiconductor Is Now To learn more about onsemi™, please visit our website at www.onsemi.com onsemi and       and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as-is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. Other names and brands may be claimed as the property of others. LCD and Camera EMI Filter Array with ESD Protection CM1430 Features Product Description • The CM1430 is a family of pi-style EMI filter arrays with ESD protection, which integrates four, six and eight filters (C-R-C) in small form factor TDFN 0.40mm pitch packages. The CM1430 has component values of 8.5pF-100Ω-8.5pF per channel. The CM1430 has a cut-off frequency of 200MHz and can be used in applications with data rates up to 80Mbps. The parts include ESD diodes on every pin, which provide a very high level of protection for sensitive electronic components that may be subjected to electrostatic discharge (ESD). The ESD protection diodes safely dissipate ESD strikes of ±15kV, well beyond the maximum requirement of the IEC61000-4-2 international standard. Using the MILSTD-883 (Method 3015) specification for Human Body Model (HBM) ESD, the pins are protected for contact discharges at greater than ±30kV. • • • • • • • • Four, six and eight channels of EMI filtering with integrated ESD protection Pi-style EMI filters in a capacitor-resistorcapacitor (C-R-C) network ±15kV ESD protection on each channel (IEC 61000-4-2 Level 4, contact discharge) ±30kV ESD protection on each channel (HBM) Greater than 20dB attenuation (typical) at 1 GHz TDFN package with 0.40mm lead pitch: • 4-ch. = 8-lead TDFN • 6-ch. = 12-lead TDFN • 8-ch. = 16-lead TDFN Tiny TDFN package size: • 8-lead: 1.7mm x 1.35mm • 12-lead: 2.5mm x 1.35mm • 16-lead: 3.3mm x 1.35mm Increased robustness against vertical impacts during manufacturing process Lead-free version available Applications • • • • • • LCD and Camera data lines in mobile handsets I/O port protection for mobile handsets, notebook computers, PDAs etc. EMI filtering for data ports in cell phones, PDAs or notebook computers. Wireless handsets Handheld PCs/PDAs LCD and camera modules ©2010 SCILLC. All rights reserved. April 2010 Rev. 2 These devices are particularly well-suited for portable electronics (e.g. wireless handsets, PDAs, notebook computers) because of their small package and easyto-use pin assignments. In particular, the CM1430 is ideal for EMI filtering and protecting data and control lines for the I/O data ports, LCD display and camera interface in mobile handsets. The CM1430 is housed in space-saving, low-profile 8-,12- and 16-lead TDFN packages with a 0.4mm pitch and is available with lead-free finishing. This new small TDFN package provides up to 42% board space savings vs. the 0.50mm pitch TDFN packages. Publication Order Number: CM1430/D CM1430 Electrical Schematic 1 of 4, 6 or 8 EMI/RFI Filter Channels with Integrated ESD Protection Rev. 2 | Page 2 of 11 | www.onsemi.com CM1430 PIN DESCRIPTIONS DEVICE PIN(s) DEVICE PIN(s) -04 -06 -08 NAME 1 1 1 FILTER1 2 2 2 3 3 4 -04 -06 -08 NAME Filter + ESD Channel 1 8 12 16 FILTER1 Filter + ESD Channel 1 FILTER2 Filter + ESD Channel 2 7 11 15 FILTER2 Filter + ESD Channel 2 3 FILTER3 Filter + ESD Channel 3 6 10 14 FILTER3 Filter + ESD Channel 3 4 4 FILTER4 Filter + ESD Channel 4 5 9 13 FILTER4 Filter + ESD Channel 4 5 5 FILTER5 Filter + ESD Channel 5 8 12 FILTER5 Filter + ESD Channel 5 6 6 FILTER6 Filter + ESD Channel 6 7 11 FILTER6 Filter + ESD Channel 6 7 FILTER7 Filter + ESD Channel 7 10 FILTER7 Filter + ESD Channel 7 8 FILTER8 Filter + ESD Channel 8 9 FILTER8 Filter + ESD Channel 8 GND PAD GND DESCRIPTION DESCRIPTION Device Ground Ordering Information PART NUMBERING INFORMATION Standard Finish Lead-free Finish Pins Package Ordering Part Number1 Part Marking Ordering Part Number1 Part Marking 8 TDFN-8 CM1430-04DF VF CM1430-04DE VE 12 TDFN-12 CM1430-06DF N30F CM1430-06DE N30E 16 TDFN-16 CM1430-08DF N308F CM1430-08DE N308E Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER RATING UNITS -65 to +150 °C DC Power per Resistor 100 mW DC Package Power Rating 500 mW Storage Temperature Range Rev. 2 | Page 3 of 11 | www.onsemi.com CM1430 STANDARD OPERATING CONDITIONS PARAMETER Operating Temperature Range RATING UNITS -40 to +85 °C ELECTRICAL OPERATING CHARACTERISTICS (SEE NOTE1) SYMBOL R PARAMETER CONDITIONS Resistance CTOTAL MIN TYP MAX UNITS 80 100 120 Ω Total Channel Capacitance At 2.5VDC Reverse Bias, 1MHz, 30mVAC 14 17 22 pF C Capacitance C1 At 2.5VDC Reverse Bias, 1MHz, 30mVAC 7 8.5 11 pF VDIODE Standoff Voltage IDIODE=10μA 6.0 ILEAK Diode Leakage Current (reverse bias) VDIODE=+3.3V 0.1 1.0 μA VSIG Signal Clamp Voltage Positive Clamp Negative Clamp ILOAD = 10mA ILOAD = -10mA 6.8 -0.8 9.0 -0.4 V V VESD RDYN f C In-system ESD Withstand Voltage a) Human Body Model, MIL-STD-883, Method 3015 b) Contact Discharge per IEC 61000-4-2 Level 4 Note 2 Dynamic Resistance Positive Negative Cut-off Frequency ZSOURCE=50Ω, ZLOAD=50Ω 5.6 -1.5 V Channel R = 100Ω, Channel C = 8.5pF Note 1: TA=25°C unless otherwise specified. Note 2: ESD applied to input and output pins with respect to GND, one at a time. Rev. 2 | Page 4 of 11 | www.onsemi.com 30 kV 15 kV 2.3 0.9 Ω Ω 200 MHz CM1430 Performance Information Typical Filter Performance (TA=25°C, DC Bias=0V, 50 Ohm Environment) Figure 1. Insertion Loss vs. Frequency (FILTER1 Input to GND) Figure 2. Insertion Loss vs. Frequency (FILTER2 Input to GND) Rev. 2 | Page 5 of 11 | www.onsemi.com CM1430 Performance Information (cont’d) Typical Filter Performance (TA=25°C, DC Bias=0V, 50 Ohm Environment) Figure 3. Insertion Loss vs. Frequency (FILTER3 Input to GND) Figure 4. Insertion Loss vs. Frequency (FILTER4 Input to GND) Rev. 2 | Page 6 of 11 | www.onsemi.com CM1430 Performance Information (cont’d) Typical Diode Capacitance vs. Input Voltage Figure 5. Filter Capacitance vs. Input Voltage (normalized to capacitance at 2.5VDC and 25°C) Rev. 2 | Page 7 of 11 | www.onsemi.com CM1430 Mechanical Details CM1430-04DF/DE Mechanical Specifications Dimensions for the CM1430-04DF/DE suplied in a 8-lead, 0.4mm pitch TDFN package are presented below. For complete information on the TDFN-8, see the California Micro Devices TDFN Package Information document. PACKAGE DIMENSIONS Package TDFN JEDEC No. MO-229C Leads 8 Millimeters Inches Dim. Min Nom Max Min Nom Max A 0.70 0.75 0.80 0.028 0.030 0.031 A1 0.00 0.02 0.05 0.000 0.001 0.002 0.20 REF A3 0.008 REF b 0.15 0.20 0.25 0.006 0.008 0.010 D 1.60 1.70 1.80 0.063 0.067 0.071 D2 1.10 1.20 1.30 0.043 0.047 0.051 E 1.25 1.35 1.45 0.049 0.053 0.057 E2 0.30 0.40 0.50 0.012 0.016 0.020 0.40 BSC e K 0.20 L 0.15 # per tape and reel 0.016 BSC 0.008 0.25 0.35 0.006 0.010 0.014 3000 pieces Dimensions for 8-Lead, 0.4mm pitch TDFN package Controlling dimension: millimeters This package is compliant with JEDEC standard MO-229C with the exception of the "D", "D2", "E", "E2", "K" and "L" dimensions as called out in the table above. Rev. 2 | Page 8 of 11 | www.onsemi.com CM1430 Mechanical Details (cont’d) CM1430-06DF/DE Mechanical Specifications Dimensions for the CM1430-06DF/DE suplied in a 12-lead, 0.4mm pitch TDFN package are presented below. PACKAGE DIMENSIONS Package TDFN JEDEC No. MO-229C Leads 12 Millimeters Inches Dim. Min Nom Max Min Nom Max A 0.70 0.75 0.80 0.028 0.030 0.031 A1 0.00 0.02 0.05 0.000 0.001 0.002 0.20 REF A3 0.008 REF b 0.15 0.20 0.25 0.006 0.008 0.010 D 2.40 2.50 2.60 0.094 0.098 0.102 D2 1.90 2.00 2.10 0.075 0.079 0.083 E 1.25 1.35 1.45 0.049 0.053 0.057 E2 0.30 0.40 0.50 0.012 0.016 0.020 0.40 BSC e K 0.20 L 0.15 # per tape and reel 0.016 BSC 0.008 0.25 0.35 0.006 0.010 0.014 Dimensions for 12-Lead, 0.4mm pitch TDFN package 3000 pieces Controlling dimension: millimeters This package is compliant with JEDEC standard MO-229C with the exception of the "D", "D2", "E", "E2", "K" and "L" dimensions as called out in the table above. Rev. 2 | Page 9 of 11 | www.onsemi.com CM1430 Mechanical Details (cont’d) CM1430-08DF/DE Mechanical Specifications Dimensions for the CM1430-08DF/DE supplied in a 16-lead, 0.4mm pitch TDFN package are presented below. For complete information on the TDFN-16, see the California Micro Devices TDFN Package Information document. PACKAGE DIMENSIONS Package TDFN JEDEC No. MO-229C Leads 16 Millimeters Inches Dim. Min Nom Max Min Nom Max A 0.70 0.75 0.80 0.028 0.030 0.031 A1 0.00 0.02 0.05 0.000 0.001 0.002 0.200 REF A3 0.008 REF b 0.15 0.20 0.25 0.006 0.008 0.010 D 3.20 3.30 3.40 0.126 0.130 0.134 D2 2.70 2.80 2.90 0.106 0.110 0.114 E 1.25 1.35 1.45 0.049 0.053 0.057 E2 0.30 0.40 0.50 0.012 0.016 0.020 0.40 BSC e K 0.20 L 0.15 # per tape and reel 0.016 BSC 0.008 0.25 0.35 0.006 0.010 0.014 3000 pieces Dimensions for 16-Lead, 0.4mm pitch TDFN package Controlling dimension: millimeters This package is compliant with JEDEC standard MO-229C with the exception of the "D", "D2", "E", "E2", "K" and "L" dimensions as called out in the table above. Rev. 2 | Page 10 of 11 | www.onsemi.com CM1430 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 Rev. 2 | Page 11 of 11 | www.onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative