DM74ALS564AWMX

Revised February 2000 DM74ALS564A Octal D-Type Edge-Triggered Flip-Flop with 3-STATE Outputs General Description Features These 8-bit registers feature totem-pole 3-STATE outputs designed specifically for driving highly-capacitive or relatively low-impedance loads. The high-impedance state and increased high-logic-level drive provide these registers with the capability of being connected directly to and driving the bus lines in a bus-organized system without need for interface or pull-up components. They are particularly attractive for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. ■ Switching specifications at 50 pF ■ Switching specifications guaranteed over full temperature and VCC range ■ Advanced oxide-isolated, ion-implanted Schottky TTL process ■ 3-STATE buffer-type outputs drive bus lines directly The eight flip-flops of the DM74ALS564A are edge-triggered inverting D-type flip-flops. On the positive transition of the clock, the Q outputs will be set to the complement of the logic states that were set up at the D inputs. A buffered output control input can be used to place the eight outputs in either a normal logic state (HIGH or LOW logic levels) or a high-impedance state. In the high-impedance state the outputs neither load nor drive the bus lines significantly. The output control does not affect the internal operation of the flip-flops. That is, the old data can be retained or new data can be entered even while the outputs are OFF. Ordering Code: Order Number Package Number DM74ALS564AWM M20B 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide Package Description DM74ALS564AN N20A 20-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. Connection Diagram © 2000 Fairchild Semiconductor Corporation DS006225 www.fairchildsemi.com DM74ALS564A Octal D-Type Edge-Triggered Flip-Flop with September 1986 DM74ALS564A Function Table Output Logic Diagram Clock D L ↑ H L L ↑ L H Control Output Q L L X Q0 H X X Z L = LOW State H = HIGH State X = Don’t Care ↑ = Positive Edge Transition Z = High Impedance State Q0 = Previous Condition of Q www.fairchildsemi.com 2 Supply Voltage 7V Input Voltage 7V Voltage Applied to Disabled Output 5.5V Note 1: The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table will define the conditions for actual device operation. 0°C to +70°C Operating Free Air Temperature Range −65°C to +150°C Storage Temperature Range Typical θJA N Package 56.0°C/W M Package 75.0°C/W Recommended Operating Conditions Symbol Parameter Min Nom Max 4.5 5 5.5 Units VCC Supply Voltage VIH HIGH Level Input Voltage V VIL LOW Level Input Voltage 0.8 V IOH HIGH Level Output Current −2.6 mA IOL LOW Level Output Current fCLOCK Clock Frequency tW Width of Clock Pulse 2 V 0 24 mA 30 MHz HIGH 14 ns LOW 14 ns ns tSU Data Setup Time (Note 3) 15↑ tH Data Hold Time (Note 3) 0↑ TA Free Air Operating Temperature 0 ns °C 70 Note 2: This product meets application requirements of 500 temperature cycles from −65°C to +150°C. Note 3: The (↑) arrow indicates the positive edge of the Clock is used for reference. Electrical Characteristics over recommended operating free air temperature range. All typical values are measured at VCC = 5V, TA = 25°C. Symbol Parameter Conditions VIK Input Clamp Voltage VCC = 4.5V, II = −18 mA VOH HIGH Level VCC = 4.5V Output Voltage Min IOH = Max VIL = VILMax VCC = 4.5V to 5.5V IOH = −400 µA 2.4 Typ Max Units −1.2 V 3.2 V VCC − 2 V VOL LOW Level VCC = 4.5V IOL = 12 mA 0.25 0.4 V Output Voltage VIH = 2V IOL = 24 mA 0.35 0.5 V II Input Current @ Maximum 0.1 mA Input Voltage VCC = 5.5V, VIH = 7V IIH HIGH Level Input Current VCC = 5.5V, VIH = 2.7V 20 µA IIL LOW Level Input Current VCC = 5.5V, VIL = 0.4V −0.2 mA IO Output Drive Current VCC = 5.5V, VO = 2.25V −112 mA IOZH OFF-State Output Current VCC = 5.5V, VIH = 2V 20 µA IOZL ICC HIGH Level Voltage Applied VO = 2.7V OFF-State Output Current VCC = 5.5V, VIH = 2V LOW Level Voltage Applied VO = 0.4V Supply Current VCC = 5.5V −30 Outputs HIGH Outputs OPEN 3 10 −20 µA 18 mA Outputs LOW 15 24 mA Outputs Disabled 16 30 mA www.fairchildsemi.com DM74ALS564A Absolute Maximum Ratings(Note 1) DM74ALS564A Switching Characteristics over recommended operating free air temperature range Symbol Parameter Conditions fMAX Maximum Clock Frequency VCC = 4.5V to 5.5V tPLH Propagation Delay Time RL = 500Ω LOW-to-HIGH Level Output CL = 50 pF tPHL tPZL tPHZ tPLZ Propagation Delay Time Min Max MHz Any Q 4 14 ns Clock Any Q 4 14 ns Any Q 4 18 ns Any Q 4 18 ns Any Q 2 10 ns Any Q 3 15 ns Output to HIGH Level Output Control Output Enable Time Output to LOW Level Output Control Output Disable Time Output from HIGH Level Output Control Output Disable Time Output from LOW Level Output Control 4 Units Clock Output Enable Time www.fairchildsemi.com To 30 HIGH-to-LOW Level Output tPZH From DM74ALS564A Physical Dimensions inches (millimeters) unless otherwise noted 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide Package Number M20B 5 www.fairchildsemi.com DM74ALS564A Octal D-Type Edge-Triggered Flip-Flop with Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 20-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide Package Number N20A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com www.fairchildsemi.com 6