MC74ACT240DWG

MC74AC240, MC74ACT240 Octal Buffer/Line Driver with 3-State Outputs The MC74AC240/74ACT240 is an octal buffer and line driver designed to be employed as a memory address driver, clock driver and bus oriented transmitter or receiver which provides improved PC board density. www.onsemi.com Features • 3−State Outputs Drive Bus Lines or Buffer Memory Address • • • SOIC−20W DW SUFFIX CASE 751D Registers Outputs Source/Sink 24 mA ′ACT240 Has TTL Compatible Inputs These are Pb−Free Devices 1 TSSOP−20 DT SUFFIX CASE 948E TRUTH TABLE Inputs Outputs OE1 D (Pins 12, 14, 16, 18) L L H L H X H L Z NOTE: 1 ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 6 of this data sheet. H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Z = High Impedance DEVICE MARKING INFORMATION See general marking information in the device marking section on page 7 of this data sheet. TRUTH TABLE Inputs Outputs OE2 D (Pins 3, 5, 7, 9) L L H L H X H L Z NOTE: H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Z = High Impedance VCC OE2 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 OE1 GND Figure 1. Pinout: 20−Lead Packages Conductors (Top View) © Semiconductor Components Industries, LLC, 2015 February, 2015 − Rev. 9 1 Publication Order Number: MC74AC240/D MC74AC240, MC74ACT240 MAXIMUM RATINGS Symbol Parameter Value Unit −0.5 to +7.0 V VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) −0.5 to VCC +0.5 V DC Output Voltage (Referenced to GND) (Note 1) −0.5 to VCC +0.5 V VOUT IIK DC Input Diode Current ±20 mA IOK DC Output Diode Current ±50 mA IOUT DC Output Sink/Source Current ±50 mA ICC DC Supply Current, per Output Pin ±50 mA IGND DC Ground Current, per Output Pin ±100 mA TSTG Storage Temperature Range *65 to )150 _C TL Lead temperature, 1 mm from Case for 10 Seconds 260 _C TJ Junction Temperature Under Bias 140 _C qJA Thermal Resistance (Note 2) 65.8 110.7 _C/W MSL Moisture Sensitivity FR Flammability Rating VESD ILatchup SOIC TSSOP Level 1 Oxygen Index: 30% − 35% ESD Withstand Voltage UL 94 V−0 @ 0.125 in Human Body Model (Note 3) Machine Model (Note 4) Charged Device Model (Note 5) Latchup Performance Above VCC and Below GND at 85_C (Note 6) > 2000 > 200 > 1000 V ±100 mA Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. IO absolute maximum rating must be observed. 2. The package thermal impedance is calculated in accordance with JESD 51−7. 3. Tested to EIA/JESD22−A114−A. 4. Tested to EIA/JESD22−A115−A. 5. Tested to JESD22−C101−A. 6. Tested to EIA/JESD78. RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT tr, tf Parameter Min Typ Max ′AC 2.0 5.0 6.0 ′ACT 4.5 5.0 5.5 0 − VCC VCC @ 3.0 V − 150 − VCC @ 4.5 V − 40 − VCC @ 5.5 V − 25 − VCC @ 4.5 V − 10 − VCC @ 5.5 V − 8.0 − −40 25 85 °C Supply Voltage DC Input Voltage, Output Voltage (Ref. to GND) Input Rise and Fall Time (Note 7) ′AC Devices except Schmitt Inputs Unit V V ns/V tr, tf Input Rise and Fall Time (Note 8) ′ACT Devices except Schmitt Inputs TA Operating Ambient Temperature Range IOH Output Current − High − − −24 mA IOL Output Current − Low − − 24 mA ns/V Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. 7. VIN from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times. 8. VIN from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times. www.onsemi.com 2 MC74AC240, MC74ACT240 DC CHARACTERISTICS 74AC Symbol Parameter VCC (V) 74AC TA = +25°C Typ VIH VIL VOH VOL TA =−40°C to +85°C Unit Conditions Guaranteed Limits Minimum High Level Input Voltage 3.0 4.5 5.5 1.5 2.25 2.75 2.1 3.15 3.85 2.1 3.15 3.85 V VOUT = 0.1 V or VCC − 0.1 V Maximum Low Level Input Voltage 3.0 4.5 5.5 1.5 2.25 2.75 0.9 1.35 1.65 0.9 1.35 1.65 V VOUT = 0.1 V or VCC − 0.1 V Minimum High Level Output Voltage 3.0 4.5 5.5 2.99 4.49 5.49 2.9 4.4 5.4 2.9 4.4 5.4 V 3.0 4.5 5.5 − − − 2.56 3.86 4.86 2.46 3.76 4.76 3.0 4.5 5.5 0.002 0.001 0.001 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 5.5 − − − 0.36 0.36 0.36 0.44 0.44 0.44 Maximum Low Level Output Voltage IOUT = −50 mA V *VIN = VIL or VIH −12 mA IOH −24 mA −24 mA IOUT = 50 mA V V *VIN = VIL or VIH 12 mA IOL 24 mA 24 mA IIN Maximum Input Leakage Current 5.5 − ±0.1 ±1.0 mA VI = VCC, GND IOZ Maximum 3−State Current 5.5 − ±0.5 ±5.0 mA VI (OE) = VIL, VIH VI = VCC, GND VO = VCC, GND 5.5 − − 75 mA VOLD = 1.65 V Max 5.5 − − −75 mA VOHD = 3.85 V Min 5.5 − 8.0 80 mA VIN = VCC or GND IOLD IOHD ICC †Minimum Dynamic Output Current Maximum Quiescent Supply Current *All outputs loaded; thresholds on input associated with output under test. †Maximum test duration 2.0 ms, one output loaded at a time. NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC. www.onsemi.com 3 MC74AC240, MC74ACT240 AC CHARACTERISTICS (For Figures and Waveforms − See AND8277/D at www.onsemi.com) 74AC Parameter Symbol VCC* TA = +25°C (V) CL = 50 pF 74AC TA = −40°C to +85°C Unit Fig. CL = 50 pF Min Typ Max Min Max No. tPLH Propagation Delay Data to Output 3.3 5.0 1.5 1.5 6.0 4.5 8.0 6.5 1.0 1.0 9.0 7.0 ns 3−5 tPHL Propagation Delay Data to Output 3.3 5.0 1.5 1.5 5.5 4.5 8.0 6.0 1.0 1.0 8.5 6.5 ns 3−5 tPZH Output Enable Time 3.3 5.0 1.5 1.5 6.0 5.0 10.5 7.0 1.0 1.0 11.0 8.0 ns 3−7 tPZL Output Enable Time 3.3 5.0 1.5 1.5 7.0 5.5 10.0 8.0 1.0 1.0 11.0 8.5 ns 3−8 tPHZ Output Disable Time 3.3 5.0 1.5 1.5 7.0 6.5 10.0 9.0 1.0 1.0 10.5 9.5 ns 3−7 tPLZ Output Disable Time 3.3 5.0 1.5 1.5 7.5 6.5 10.5 9.0 1.0 1.0 11.5 9.5 ns 3−8 * Voltage Range 3.3 V is 3.3 V ±0.3 V. Voltage Range 5.0 V is 5.0 V ±0.5 V. DC CHARACTERISTICS Symbol Parameter VCC (V) 74ACT 74ACT TA = +25°C TA = −40°C to +85°C Typ Unit Conditions Guaranteed Limits VIH Minimum High Level Input Voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 V VOUT = 0.1 V or VCC − 0.1 V VIL Maximum Low Level Input Voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 V VOUT = 0.1 V or VCC − 0.1 V VOH Minimum High Level Output Voltage 4.5 5.5 4.49 5.49 4.4 5.4 4.4 5.4 V 4.5 5.5 − − 3.86 4.86 3.76 4.76 4.5 5.5 0.001 0.001 0.1 0.1 0.1 0.1 4.5 5.5 − − 0.36 0.36 0.44 0.44 V *VIN = VIL or VIH 24 mA IOL 24 mA Maximum Input Leakage Current 5.5 − ±0.1 ±1.0 mA VI = VCC, GND Additional Max. ICC/Input 5.5 0.6 − 1.5 mA VI = VCC − 2.1 V Maximum 3−State Current 5.5 − ±0.5 ±5.0 mA VI (OE) = VIL, VIH VI = VCC, GND VO = VCC, GND 5.5 − − 75 mA VOLD = 1.65 V Max 5.5 − − −75 mA VOHD = 3.85 V Min 5.5 − 8.0 80 mA VIN = VCC or GND VOL IIN DICCT IOZ IOLD IOHD ICC Maximum Low Level Output Voltage †Minimum Dynamic Output Current Maximum Quiescent Supply Current *All outputs loaded; thresholds on input associated with output under test. †Maximum test duration 2.0 ms, one output loaded at a time. www.onsemi.com 4 V V IOUT = −50 mA *VIN = VIL or VIH IOH −24 mA −24 mA IOUT = 50 mA MC74AC240, MC74ACT240 AC CHARACTERISTICS (For Figures and Waveforms − See Section 3 of the ON Semiconductor FACT Data Book, DL138/D) VCC* Parameter Symbol (V) 74ACT 74ACT TA = +25°C CL = 50 pF TA = −40°C to +85°C CL = 50 pF Min Typ Max Min Max Unit Fig. No. tPLH Propagation Delay Data to Output 5.0 1.5 6.0 8.5 1.5 9.5 ns 3−5 tPHL Propagation Delay Data to Output 5.0 1.5 5.5 7.5 1.5 8.5 ns 3−5 tPZH Output Enable Time 5.0 1.5 7.0 8.5 1.0 9.5 ns 3−7 tPZL Output Enable Time 5.0 2.0 7.0 9.5 1.5 10.5 ns 3−8 tPHZ Output Disable Time 5.0 2.0 8.0 9.5 2.0 10.5 ns 3−7 tPLZ Output Disable Time 5.0 2.5 6.5 10.0 2.0 10.5 ns 3−8 *Voltage Range 5.0 V is 5.0 V ±0.5 V. CAPACITANCE Symbol Value Parameter Typ Unit Test Conditions CIN Input Capacitance 4.5 pF VCC = 5.0 V CPD Power Dissipation Capacitance 45 pF VCC = 5.0 V www.onsemi.com 5 MC74AC240, MC74ACT240 ORDERING INFORMATION Device Package Shipping† SOIC−20 (Pb−Free) 1000 / Tape & Reel MC74AC240DWG 38 Units / Rail MC74AC240DWR2G MC74ACT240DWG 38 Units / Rail MC74ACT240DWR2G 1000 / Tape & Reel MC74AC240DTR2G 2500 / Tape & Reel TSSOP−20 (Pb−Free) MC74ACT240DTR2G 2500 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. MARKING DIAGRAMS SOIC−20W TSSOP−20 20 20 AC 240 ALYWG G AC240 AWLYYWWG 1 1 20 20 ACT 240 ALYWG G ACT240 AWLYYWWG 1 1 A = Assembly Location WL, L = Wafer Lot YY, Y = Year WW, W = Work Week G or G = Pb−Free Package (Note: Microdot may be in either location) www.onsemi.com 6 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SOIC−20 WB CASE 751D−05 ISSUE H DATE 22 APR 2015 SCALE 1:1 A 20 q X 45 _ M E h 0.25 H NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT MAXIMUM MATERIAL CONDITION. 11 B M D 1 10 20X B b 0.25 M T A S B DIM A A1 b c D E e H h L q S L A 18X e SEATING PLANE A1 c T GENERIC MARKING DIAGRAM* RECOMMENDED SOLDERING FOOTPRINT* 20 20X 20X 1.30 0.52 20 XXXXXXXXXXX XXXXXXXXXXX AWLYYWWG 11 1 11.00 1 XXXXX A WL YY WW G 10 1.27 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. DOCUMENT NUMBER: DESCRIPTION: MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 12.65 12.95 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0_ 7_ 98ASB42343B SOIC−20 WB = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “G”, may or may not be present. Some products may not follow the Generic Marking. Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 onsemi and are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS TSSOP−20 WB CASE 948E ISSUE D DATE 17 FEB 2016 SCALE 2:1 20X 0.15 (0.006) T U 2X L K REF 0.10 (0.004) S L/2 20 M T U S V ÍÍÍÍ ÍÍÍÍ ÍÍÍÍ K K1 S J J1 11 B SECTION N−N −U− PIN 1 IDENT 0.25 (0.010) N 1 10 M 0.15 (0.006) T U S A −V− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. N F DETAIL E −W− C G D H DETAIL E 0.100 (0.004) −T− SEATING PLANE DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 6.40 6.60 4.30 4.50 --1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.27 0.37 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.252 0.260 0.169 0.177 --0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.011 0.015 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ GENERIC MARKING DIAGRAM* SOLDERING FOOTPRINT 7.06 XXXX XXXX ALYWG G 1 0.65 PITCH 16X 0.36 16X 1.26 DOCUMENT NUMBER: 98ASH70169A DESCRIPTION: TSSOP−20 WB A L Y W G = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “ G”, may or may not be present. DIMENSIONS: MILLIMETERS Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative