NCP51402MNTXG

DATA SHEET www.onsemi.com 3 Amp VTT Termination Regulator DDR1, DDR2, DDR3, LPDDR3, DDR4 DFN10, 3x3, 0.5P CASE 506CL NCP51402 The NCP51402 is a source/sink Double Data Rate (DDR) termination regulator specifically designed for low input voltage and low−noise systems where space is a key consideration. The NCP51402 maintains a fast transient response and only requires a minimum output capacitance of 20 mF. The NCP51402 supports a remote sensing function and all power requirements for DDR VTT bus termination. The NCP51402 can also be used in low−power chipsets and graphics processor cores that require dynamically adjustable output voltages. The NCP51402 is available in the thermally−efficient DFN10 Exposed Pad package, and is rated both Green and Pb−free. • • • • • Input Voltage Rails: Supports 2.5 V, 3.3 V and 5 V Rails PVCC Voltage Range: 1.1 to 3.5 V Integrated Power MOSFETs Fast Load−Transient Response PGOOD − Logic output pin to Monitor VTT Regulation EN − Logic input pin for Shutdown mode VRI − Reference Input Allows for Flexible Input Tracking Either Directly or Through Resistor Divider Remote Sensing (VTTS) Built−in Under Voltage Lockout and Over Current Limit Thermal Shutdown Small, Low−Profile 10−pin, 3x3 DFN Package These Devices are Pb−Free and are RoHS Compliant Applications • • • • • • • • 51402 ALYWG G 51402 A L Y W G = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) Features • • • • • • • MARKING DIAGRAM PIN CONNECTION VRI 1 PVCC 2 VTT 3 PGND VTTS + 10 VCC 9 PGOOD 8 GND 4 7 EN 5 6 VRO GND Exposed Pad ORDERING INFORMATION Device NCP51402MNTXG DDR Memory Termination Desktop PC’s, Notebooks, and Workstations Servers and Networking equipment Telecom/Datacom, GSM Base Station Graphics Processor Core Supplies Set Top Boxes, LCD−TV/PDP−TV, Copier/Printers Chipset/RAM Supplies as Low as 0.5 V Active Bus Termination Package Shipping† DFN10 (Pb−Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. (see notes on page 7) © Semiconductor Components Industries, LLC, 2016 August, 2021 − Rev. 2 1 Publication Order Number: NCP51402/D NCP51402 PIN FUNCTION DESCRIPTION Pin Number Pin Name 1 VRI Pin Function 2 PVCC 3 VTT 4 PGND Power Ground. Internally connected to the output sink MOSFET. 5 VTTS VTT Sense Input. The VTTS pin provides accurate remote feedback sensing of VTT. Connect VTTS to the remote DDR termination bypass capacitors. 6 VRO Independent Buffered VTT Reference Output. Sources and sinks over 5 mA. Connect to GND thru 0.1 mF ceramic capacitor. 7 EN Shutdown Control Input. CMOS compatible input. Logic high = enable, logic low = shutdown. Connect to VDDQ for normal operation. 8 GND 9 PGOOD 10 VCC VTT External Reference Input ( set to VDDQ / 2 thru resistor network ). Power input. Internally connected to the output source MOSFET. Power Output of the Linear Regulator. Common Ground. Power Good (Open Drain output). Analog power supply input. Connect to GND thru a 1 − 4.7 mF ceramic capacitor. THERMAL PAD Pad for thermal connection. The exposed pad must be connected to the ground plane using multiple vias for maximum power dissipation performance. ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit −0.3 to 6.0 V EN, PGOOD (Note 1) −0.3 to 6.0 V PGND to GND (Note 1) −0.3 to +0.3 V TSTG −55 to 150 °C TJ 150 °C ESDHBM 2000 V VCC, PVCC, VTT, VTTS, VRI, VRO (Note 1) Storage Temperature Operating Junction Temperature Range ESD Capability, Human Body Model (Note 2) Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area. 2. This device series incorporates ESD protection and is tested by the following method: ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114) ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115) Latchup Current Maximum Rating tested per JEDEC standard: JESD78. DISSIPATION RATINGS Package TA = 255C Power Rating Derating Factor above TA = 255C TA = +855C Power Rating 10−Pin DFN 1.92 W 19 mW/°C 0.79 W RECOMMENED OPERATING CONDITIONS Rating Symbol Value Unit Supply Voltage VCC 2.375 to 5.5 V Voltage Range VRO −0.1 to 1.8 V VRI 0.5 to 1.8 PVCC, VTT, VTTS, EN, PGOOD −0.1 to 3.5 PGND −0.1 to +0.1 TA −40 to +125 Operating Free−Air Temperature °C Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. www.onsemi.com 2 NCP51402 ELECTRICAL CHARACTERISTICS −40°C ≤ TA ≤ 125°C; VCC = 3.3 V; PVCC = 1.8 V; VRI = VTTS = 0.9 V; EN = VCC; COUT = 3 x 10 mF (Ceramic); unless otherwise noted. Parameter Conditions Symbol Min Typ Max Units 0.7 1 mA mA SUPPLY CURRENT VCC Supply Current TA = +25°C, EN = 3.3 V, No Load VCC Shutdown Current TA = +25°C, EN = 0 V, VRI = 0 V, No Load IVCC IVCC SHD TA = +25°C, EN = 0 V, VRI > 0.4 V, No Load VCC UVLO Threshold Wake−up, TA = +25°C VUVLO 2.15 Hysteresis 65 80 200 400 2.3 2.375 50 PVCC Supply Current TA = +25°C, EN = 3.3 V, No Load PVCC Shutdown Current TA = +25°C, EN = 0 V, No Load V mV IPVCC 1 50 mA IPVCC SHD 0.1 50 mA VTT OUTPUT VTT Output DC Voltage PVCC = 1.50 V, VRO = 0.75 V, ITT = 0 A VOS mV 0.75 PVCC = 1.35 V, VRO = 0.675 V, ITT = 0 A 0.675 PVCC = 1.20 V, VRO = 0.60 V, ITT = 0 A 0.60 VTT Output Tolerance to VRO −2 A < ITT < 2 A PVCC = 1.50 V, VRO = 0.75 V −18 +18 PVCC = 1.20 V, VRO = 0.60 V PVCC = 1.35 V, VRO = 0.675 V −20 +20 Source Current Limit VTTS = 90% * VRO 3 4.5 A Sink Current Limit VTTS = 110% * VRO 3.5 5.5 A VTT Rise Time Enable to VTT = 95% of VRI, VTT has 100 mF ceramic cap load, VRI = 600 mV 25 35 ms Discharge MOSFET On−resistance VRI = 0 V, VTT = 0.3 V, EN = 0 V, TA = +25°C 18 25 W 1.8 V +1 mA 435 mV RDIS mV VRI − INPUT REFERENCE VRI Voltage Range VRI VRI Input−bias Current EN = 3.3 V VRI UVLO Voltage VRI rising VRI UVLO Hysteresis VRI HYS 0.5 IRI 360 390 60 VRO − OUTPUT REFERENCE VRO Voltage VRI V VRO Voltage Tolerance to VRI IRO = ±10 mA, 0.6 V ≤ VRI ≤ 1.25 V −15 VRO Source Current Limit VRO = 0 V 10 40 mA VRO Sink Current Limit VRO = 0 V 10 40 mA +15 mV PGOOD − POWERGOOD COMPARATOR PGOOD Lower Threshold (with respect to VRO) −23.5% −20% −17.5% PGOOD Upper Threshold (with respect to VRO) 17.5% 20% 23.5% PGOOD Hysteresis V/V 5% PGOOD Start−up Delay Start−up rising edge, VTTS within 15% of VRO PGOOD Leakage Current VTTS = VRI (PGOOD = True) PGOOD = VCC + 0.2 V PGOOD = False Delay VTTS is beyond ±20% PGOOD trip thresholds PGOOD Output Low Voltage IGOOD = 4 mA 2 ms 1 ms 10 0.4 www.onsemi.com 3 mA V NCP51402 ELECTRICAL CHARACTERISTICS −40°C ≤ TA ≤ 125°C; VCC = 3.3 V; PVCC = 1.8 V; VRI = VTTS = 0.9 V; EN = VCC; COUT = 3 x 10 mF (Ceramic); unless otherwise noted. Parameter Conditions Symbol Min EN Logic high VIH 1.7 EN Logic low VIL Typ Max Units EN − ENABLE LOGIC Logic Input Threshold Hysteresis Voltage EN pin Logic Leakage Current EN pin, TA = +25°C 0.3 VENHYS IILEAK V 0.5 −1 V +1 mA THERMAL SHUTDOWN Thermal Shutdown Temperature TSD 150 °C Thermal Shutdown Hysteresis TSH 25 °C Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 4 NCP51402 Figure 1. Typical DDR−3 Application Schematic Figure 2. Block Diagram www.onsemi.com 5 NCP51402 General PGOOD − PowerGood The NCP51402 is a sink/source tracking termination regulator specifically designed for low input voltage and low external component count systems where space is a key application parameter. The NCP51402 integrates a high−performance, low−dropout (LDO) linear regulator that is capable of both sourcing and sinking current. The LDO regulator employs a fast feedback loop so that small ceramic capacitors can be used to support the fast load transient response. To achieve tight regulation with minimum effect of trace resistance, a remote sensing terminal, VTTS, should be connected to the positive terminal of the output capacitors as a separate trace from the high current path from VTT. The NCP51402 provides an open−drain PGOOD output that goes high when the VTT output is within ±20% of VRO. PGOOD de−asserts within 10 ms after the output exceeds the limits of the PowerGood window. During initial VTT startup, PGOOD asserts high 2 ms after the VTT enters power good window. Because PGOOD is an open−drain output, a 100 kW, pull−up resistor between PGOOD and a stable active supply voltage rail is required. The LDO has a constant over−current limit (OCL). Note that the OCL level reduces by one−half when the output voltage is not within the power good window. This reduction is non−latch protection. For VCC under−voltage lockout (UVLO) protection, the NCP51402 monitors VCC voltage. When the VCC voltage is lower than the UVLO threshold voltage, both the VTT and VRO regulators are powered off. This shutdown is also non−latch protection. VRI − Generation of Internal Voltage Reference The output voltage, VTT, is regulated to VRO. When VRI is configured for standard DDR termination applications, VRI can be set by an external equivalent ratio voltage divider connected to the memory supply bus (VDDQ). The NCP51402 supports VRI voltage from 0.5 V to 1.8 V, making it versatile and ideal for many types of low−power LDO applications. Thermal Shutdown with Hysteresis If the NCP51402 is to operate in elevated temperatures for long durations, care should be taken to ensure that the maximum operating junction temperature is not exceeded. To guarantee safe operation, the NCP51402 provides on−chip thermal shutdown protection. When the chip junction temperature exceeds 150°C, the part will shutdown. When the junction temperature falls back to 125°C, the device resumes normal operation. If the junction temperature exceeds the thermal shutdown threshold then the VTT and VRO regulators are both shut off, discharged by the internal discharge MOSFETs. The shutdown is a non−latch protection. VRO − Reference Output When it is configured for DDR termination applications, VRO generates the DDR VTT reference voltage for the memory application. It is capable of supporting both a sourcing and sinking load of 10 mA. VRO becomes active when VRI voltage rises to 435 mV and VCC is above the UVLO threshold. When VRO is less than 360 mV, it is disabled and subsequently discharges to GND through an internal 10 kW MOSFET. VRO is independent of the EN pin state. Tracking Startup and Shutdown The NCP51402 also supports tracking startup and shutdown when EN is tied directly to the system bus and not used to turn on or turn off the device. During tracking startup, VTT follows VRO once VRI voltage is greater than 435 mV. VRI follows the rise of VDDQ memory supply rail via a voltage divider. PGOOD is asserted 2 ms after VTT is within ±20% of VRO. During tracking shutdown, VTT falls following VRO until VRO reaches 360 mV. Once VRO falls below 360 mV, the internal discharge MOSFETs are turned on and quickly discharge both VRO and VTT to GND. PGOOD is de−asserted once VTT is beyond the ±20% range of VRO. EN − Enable Control When EN is driven high, the NCP51402 VTT regulator begins normal operation. When EN is driven low, VTT is discharges to GND through an internal 18−W MOSFET. VREF remains on when EN is driven low. www.onsemi.com 6 NCP51402 VTT Droop Droop is a technique to reduce error voltage due to a transient, or as a design tradeoff, to reduce system cost for a given transient magnitude, by using smaller, less expensive capacitors. Figure 3 shows the transient response in a system without droop and is showing a peak−to−peak error voltage of ±30 mV. Figure 4 shows the same magnitude of transient response, but this time the regulation is performed *with* droop. For example the magnitude of the transient in Figure 4 is +30 mV = +20 mV – (−10 mV) which is the same magnitude as in Figure 3, but since the output voltage is allowed to sag 10 mV when loaded (as opposed to the “perfect” Load Regulation, i.e. 0 mV of VTT output voltage sag as shown in Figure 3) then this same +30 mV transient starts at −10 mV and now only peaks to +20 mV. The net result is that with 10 mV of droop, the overall, peak−to−peak error voltage has been reduced from ±30 mV to ±20 mV. VTT Startup Time In order to speed up the time it takes a modern computer to Boot−up or Resume after Stand−by, some newer motherboard specs require VTT to rise from 0 V to 95% of VTT in less than 35 msec. This new requirement is met in the new ON Semiconductor NCP51401, NCP51402 and NCP51403 devices. Figure 3. Figure 4. Legacy DDR2/3, DDR4 and Droop VTT Capacitor Selection When the popular, now industry−standard, 51200− compatible devices were first introduced, the PC memory industry was transitioning from DDR2 (VTT = 900 mV) to DDR3 (VTT = 750 mV) and a value of ±14 mV of Droop per ±1.5 amps of DC current was designed−in. This value of Droop was appropriate for the DDR2 and DDR3 memory in use at the time, but this amount of Droop has now become excessive for DDR4. For example for DDR4 with a VTT voltage of 600 mV, the 5% error tolerance is ±30 mV, which leaves no transient−response margin for a DC load of ±2 amps. This excessive DDR2/3 Droop issue of using 51200 devices in newer DDR4 applications has been solved in the new ON Semiconductor NCP51402 and NCP51403 devices, which have no Droop for improved, high−current DDR4 transient response. Many 51200−compatible devices have specified VTT capacitor ESR requirements and must be loaded with at least 20 mF of ceramic capacitance in order to guarantee stability. In contrast, the NCP51400, NCP51401 and NCP51402 were all designed to be stable with a wide range of ESR and can use both ceramic and higher−ESR, polymer capacitors. Extending the NCP5140x family of parts, in applications that have specified phase margin requirements, we have introduced the NCP51403 which has 45° of phase margin when VTT is loaded with a ceramic capacitance of 40 mF. However just like our competitor’s 51200−compatible devices, the NCP51403 cannot be loaded solely with polymer capacitors because the 45° phase margin reduces the ESR−stability range of the VTT capacitor. www.onsemi.com 7 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS DFN10, 3x3, 0.5P CASE 506CL ISSUE O SCALE 2:1 D L L A B L1 PIN ONE REFERENCE 2X 0.10 C 2X ÇÇÇ ÇÇÇ ÇÇÇ ÇÇÇ 0.10 C 0.05 C DETAIL A ALTERNATE TERMINAL CONSTRUCTIONS E ÉÉ ÉÉ ÇÇ EXPOSED Cu TOP VIEW MOLD CMPD DETAIL B A 10X 0.05 C SIDE VIEW NOTE 4 (A3) A1 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM THE TERMINAL TIP. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. TERMINAL b MAY HAVE MOLD COMPOUND MATERIAL ALONG SIDE EDGE. MOLD FLASHING MAY NOT EXCEED 30 MICRONS ONTO BOTTOM SURFACE OF TERMINAL b. 6. FOR DEVICE OPN CONTAINING W OPTION, DETAIL B ALTERNATE CONSTRUCTION IS NOT APPLICABLE. DIM A A1 A3 b D D2 E E2 e K L L1 ALTERNATE CONSTRUCTIONS DETAIL B DATE 02 APR 2013 SEATING PLANE MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.20 0.30 3.00 BSC 2.40 2.60 3.00 BSC 1.40 1.60 0.50 BSC 0.25 −−− 0.25 0.45 0.00 0.03 XXXXX XXXXX ALYWG G D2 DETAIL A 1 e 10X L 5 A = Assembly Location L = Wafer Lot Y = Year W = Work Week G = Pb−Free Package (Note: Microdot may be in either location) E2 K GENERIC MARKING DIAGRAM* 10 6 10X b 0.10 C A B BOTTOM VIEW 0.05 C NOTE 3 10X RECOMMENDED SOLDERING FOOTPRINT* *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “ G”, may or may not be present. 2.70 0.57 1.70 3.30 PACKAGE OUTLINE 1 0.50 PITCH 10X 0.32 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. DOCUMENT NUMBER: DESCRIPTION: 98AON88041E DFN10, 3X3, 0.5P Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative