NVMFD5873NLT1G

NVMFD5873NL Power MOSFET 60 V, 13 mW, 58 A, Dual N−Channel Logic Level, Dual SO−8FL Features • • • • • • Small Footprint (5x6 mm) for Compact Designs Low RDS(on) to Minimize Conduction Losses Low Capacitance to Minimize Driver Losses NVMFD5873NLWF − Wettable Flanks Option for Enhanced Optical Inspection AEC−Q101 Qualified and PPAP Capable This is a Pb−Free Device http://onsemi.com V(BR)DSS RDS(on) MAX ID MAX 13 mW @ 10 V 60 V 58 A 16.5 mW @ 4.5 V Dual N−Channel MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Parameter Symbol Value Unit Drain−to−Source Voltage VDSS 60 V Gate−to−Source Voltage VGS "20 V ID 58 A Continuous Drain Current RYJ−mb (Notes 1, 2, 3, 4) Power Dissipation RYJ−mb (Notes 1, 2, 3) Continuous Drain Current RqJA (Notes 1, 3 & 4) Power Dissipation RqJA (Notes 1 & 3) Pulsed Drain Current Tmb = 25°C Steady State Tmb = 100°C Tmb = 25°C Steady State Operating Junction and Storage Temperature Source Current (Body Diode) Single Pulse Drain−to−Source Avalanche Energy (TJ = 25°C, VGS = 10 V, IL(pk) = 28.3 A, L = 0.1 mH, RG = 25 W) Lead Temperature for Soldering Purposes (1/8″ from case for 10 s) A 7.0 3.1 PD TA = 100°C TA = 25°C, tp = 10 ms MARKING DIAGRAM 10 TA = 100°C TA = 25°C W 54 ID W Junction−to−Ambient − Steady State (Note 3) 190 A TJ, Tstg −55 to 175 °C IS 58 A EAS 40 mJ TL 260 °C Symbol Value RYJ−mb 1.4 Unit °C/W RqJA September, 2014 − Rev. 3 5873xx AYWZZ D1 D1 D2 D2 5873NL = Specific Device Code for NVMFD5873NL 5873LW = Specific Device Code for NVMFD5873NLWF A = Assembly Location Y = Year W = Work Week ZZ = Lot Traceability ORDERING INFORMATION Package Shipping† NVMFD5873NLT1G DFN8 (Pb−Free) 1500 / Tape & Reel NVMFD5873NLWFT1G DFN8 (Pb−Free) 1500 / Tape & Reel Device 48 1. The entire application environment impacts the thermal resistance values shown, they are not constants and are only valid for the particular conditions noted. 2. Psi (Y) is used as required per JESD51−12 for packages in which substantially less than 100% of the heat flows to single case surface. 3. Surface−mounted on FR4 board using a 650 mm2, 2 oz. Cu pad. 4. Maximum current for pulses as long as 1 second are higher but are dependent on pulse duration and duty cycle. © Semiconductor Components Industries, LLC, 2014 DFN8 5x6 (SO8FL) CASE 506BT S1 G1 S2 G2 D2 D2 IDM THERMAL RESISTANCE MAXIMUM RATINGS (Note 1) Junction−to−Mounting Board (top) − Steady State (Notes 2, 3) D1 D1 1 1.6 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. Parameter S2 S1 107 Tmb = 100°C TA = 25°C G2 G1 41 PD D2 D1 1 †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. Publication Order Number: NVMFD5873NL/D NVMFD5873NL ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise specified) Parameter Symbol Test Condition Min Drain−to−Source Breakdown Voltage V(BR)DSS VGS = 0 V, ID = 250 mA 60 Drain−to−Source Breakdown Voltage Temperature Coefficient V(BR)DSS/TJ Typ Max Unit OFF CHARACTERISTICS Zero Gate Voltage Drain Current IDSS 54.9 VGS = 0 V, VDS = 60 V mV/°C TJ = 25°C 1.0 TJ = 125°C 100 IGSS VDS = 0 V, VGS = ±20 V VGS(TH) VGS = VDS, ID = 250 mA Gate−to−Source Leakage Current V ±100 mA nA ON CHARACTERISTICS (Note 5) Gate Threshold Voltage Threshold Temperature Coefficient Drain−to−Source On Resistance VGS(TH)/TJ RDS(on) Forward Transconductance gFS 1.5 2.5 −5.8 V mV/°C VGS = 10 V, ID = 15 A 10.7 13 mW VGS = 4.5 V, ID = 10 A 13.6 16.5 VDS = 5.0 V, ID = 15 A 15 S pF CHARGES AND CAPACITANCES Input Capacitance Ciss 1560 Output Capacitance Coss 145 Reverse Transfer Capacitance Crss 98 Total Gate Charge QG(TOT) 16.5 Threshold Gate Charge QG(TH) Gate−to−Source Charge QGS Gate−to−Drain Charge QGD Total Gate Charge QG(TOT) VGS = 0 V, f = 1.0 MHz, VDS = 25 V VGS = 4.5 V, VDS = 48 V, ID = 15 A nC 1.3 4.0 8.8 VGS = 10 V, VDS = 48V, ID = 15 A 30.5 nC 10.8 ns SWITCHING CHARACTERISTICS (Note 6) Turn−On Delay Time Rise Time Turn−Off Delay Time Fall Time Turn−On Delay Time Rise Time Turn−Off Delay Time Fall Time td(on) tr td(off) VGS = 4.5 V, VDS = 48 V, ID = 15 A, RG = 2.5 W 51 21 tf 42.6 td(on) 9.5 tr 13 td(off) VGS = 10 V, VDS = 48 V, ID = 15 A, RG = 2.5 W tf ns 25 6.6 DRAIN−SOURCE DIODE CHARACTERISTICS Forward Diode Voltage VSD Reverse Recovery Time tRR Charge Time ta Discharge Time tb Reverse Recovery Charge VGS = 0 V, IS = 15 A TJ = 25°C TJ = 125°C 0.8 QRR http://onsemi.com 2 ns 14.5 9.0 18 5. Pulse Test: pulse width = 300 ms, duty cycle v 2%. 6. Switching characteristics are independent of operating junction temperatures. V 0.7 22.4 VGS = 0 V, dIS/dt = 100 A/ms, IS = 15 A 1.0 nC NVMFD5873NL TYPICAL CHARACTERISTICS 80 80 10 V VDS ≥ 10 V 4.5 V ID, DRAIN CURRENT (A) ID, DRAIN CURRENT (A) 3.8 V 60 3.4 V 40 VGS = 3.0 V 20 TJ = 25°C 1.0 2.0 3.0 4.0 TJ = 25°C 20 TJ = 125°C 3.5 4.0 Figure 1. On−Region Characteristics Figure 2. Transfer Characteristics 0.020 0.015 0.010 0.005 3 4 5 6 7 8 9 VGS, GATE−TO−SOURCE VOLTAGE (V) 10 4.5 0.0200 TJ = 25°C 0.0175 0.0150 VGS = 4.5 V 0.0125 VGS = 10 V 0.0100 0.0075 0.0050 5 10 15 20 25 30 ID, DRAIN CURRENT (A) Figure 3. On−Resistance vs. VGS Figure 4. On−Resistance vs. Drain Current and Gate Voltage 100000 2.4 RDS(on), DRAIN−TO−SOURCE RESISTANCE (NORMALIZED) 3.0 VGS, GATE−TO−SOURCE VOLTAGE (V) ID = 15 A TJ = 25°C 2.2 2.5 TJ = −55°C VDS, DRAIN−TO−SOURCE VOLTAGE (V) 0.025 2 40 0 2.0 5.0 RDS(on), DRAIN−TO−SOURCE RESISTANCE (W) RDS(on), DRAIN−TO−SOURCE RESISTANCE (W) 0 0.0 60 VGS = 0 V ID = 15 A VGS = 10 V IDDS, LEAKAGE (nA) 2.0 1.8 1.6 1.4 1.2 1.0 10000 TJ = 150°C TJ = 125°C 1000 0.8 0.6 −50 100 −25 0 25 50 75 100 125 150 175 10 20 30 40 50 TJ, JUNCTION TEMPERATURE (°C) VDS, DRAIN−TO−SOURCE VOLTAGE (V) Figure 5. On−Resistance Variation with Temperature Figure 6. Drain−to−Source Leakage Current vs. Voltage http://onsemi.com 3 60 NVMFD5873NL TYPICAL CHARACTERISTICS VGS = 0 V TJ = 25°C Ciss C, CAPACITANCE (pF) VGS, GATE−TO−SOURCE VOLTAGE (V) 2000 1500 1000 500 Coss Crss 0 0 10 20 30 40 50 QT 8 6 Qgs 4 Qgd TJ = 25°C VDS = 48 V ID = 15 A 2 0 60 0 5 10 15 20 25 30 VDS, DRAIN−TO−SOURCE VOLTAGE (V) Qg, TOTAL GATE CHARGE (nC) Figure 7. Capacitance Variation Figure 8. Gate−to−Source and Drain−to−Source Voltage vs. Total Charge 35 80 1000 VDS = 48 V ID = 15 A VGS = 10 V IS, SOURCE CURRENT (A) 70 100 tf tr td(off) td(on) 10 1 1 10 100 VGS = 0 V TJ = 25°C 60 50 40 30 20 10 0 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 RG, GATE RESISTANCE (W) VSD, SOURCE−TO−DRAIN VOLTAGE (V) Figure 9. Resistive Switching Time Variation vs. Gate Resistance Figure 10. Diode Forward Voltage vs. Current 100 ID, DRAIN CURRENT (A) t, TIME (ns) 10 0.01 ms 10 0.1 ms 1 0.1 1 ms NVMFD5873NL FBSOA TA = 25°C, 650 mm2, 2 oz Cu Pad, VGS = 10 V 0.1 10 ms 1 10 VDS, DRAIN−TO−SOURCE VOLTAGE (V) Figure 11. Maximum Rated Forward Biased Safe Operating Area http://onsemi.com 4 100 NVMFD5873NL TYPICAL CHARACTERISTICS 100 R(t) (°C/W) Duty Cycle = 50% 10 20% 10% 5% 1 2% 1% 0.1 Single Pulse 0.01 0.000001 0.00001 0.0001 0.001 0.01 0.1 PULSE TIME (sec) Figure 12. Thermal Response http://onsemi.com 5 1 10 100 1000 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS DFN8 5x6, 1.27P Dual Flag (SO8FL−Dual) CASE 506BT ISSUE F 1 2X SCALE 2:1 0.20 C D A B D1 8 7 6 ÉÉ ÉÉ ÉÉ PIN ONE IDENTIFIER NOTE 7 1 2 2X 0.20 C 5 DATE 23 NOV 2021 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 MM FROM THE TERMINAL TIP. 4. PROFILE TOLERANCE APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 6. SEATING PLANE IS DEFINED BY THE TERMINALS. A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE TO THE LOWEST POINT ON THE PACKAGE BODY. 7. A VISUAL INDICATOR FOR PIN 1 MUST BE LOCATED IN THIS AREA. E1 E 4X h 3 4 c TOP VIEW A1 0.10 C A DETAIL B 0.10 C NOTE 4 C SIDE VIEW DETAIL A D2 D3 4X e 1 SEATING PLANE NOTE 6 ALTERNATE CONSTRUCTION DETAIL A L K 4 DIM A A1 b b1 c D D1 D2 D3 E E1 E2 e G h K K1 L M N MILLIMETERS NOM MIN MAX −−− 0.90 1.10 −−− −−− 0.05 0.33 0.42 0.51 0.33 0.42 0.51 0.20 −−− 0.33 5.15 BSC 4.70 4.90 5.10 3.90 4.10 4.30 1.50 1.70 1.90 6.15 BSC 5.70 5.90 6.10 3.90 4.15 4.40 1.27 BSC 0.45 0.55 0.65 −−− −−− 12 _ 0.51 −−− −−− 0.56 −−− −−− 0.48 0.61 0.71 3.25 3.50 3.75 1.80 2.00 2.20 SOLDERING FOOTPRINT* DETAIL B 4.56 M 4X b1 N 4X 8 G 5 8X 2X 2X 2.08 8X E2 0.75 0.56 b K1 BOTTOM VIEW 0.10 C A B 0.05 C GENERIC MARKING DIAGRAM* 1 XXXXXX AYWZZ NOTE 3 4.84 4X 6.59 3.70 0.70 4X XXXXXX = Specific Device Code A = Assembly Location Y = Year W = Work Week ZZ = Lot Traceability 1.40 2.30 1.00 1.27 PITCH 5.55 DIMENSION: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “G”, may or may not be present. Some products may not follow the Generic Marking. DOCUMENT NUMBER: DESCRIPTION: 98AON50417E Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. DFN8 5X6, 1.27P DUAL FLAG (SO8FL−DUAL) PAGE 1 OF 1 onsemi and are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative