GS1J

DATA SHEET G S1A~GS1M S URFACE MOUNT RECTIFIER VOLTAGE- 50 to 1000 Volts CURRENT - 1.0 Ampere FEATURES .114 (2.90) .098 (2.50) .062 (1.60) .055 (1.40) .181 (4.60) .157 (4.00) .012 (.305) .006 (.152) SMA / DO-214AC Unit: inch ( mm ) • For surface mounted applications • Low profile package • Built-in strain relief • Easy pick and place • Plastic package has Underwriters Laboratory Flammability Classification 94V-O • Glass passivated chip junction • High temperature soldering : 260°C /10 seconds at terminals MECHANICAL DATA Case: JEDEC DO-214AC molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard packaging: 12mm tape (EIA-481) Weight: 0.002 ounce, 0.064 gram .096 (2.30) .078 (2.00) .060 (1.52) .030 (0.76) .008(.203) .002(.051) .208 (5.28) .188 (4.80) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. SYMBOLS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, at T L =75°C Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current at Rated DC Blocking Voltage TA=25°C TA=125°C GS1A GS1B GS1D GS1G GS1J GS1K GS1M UNIT V V V A VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 400 280 400 1.0 600 420 600 800 560 800 1000 700 100 IFSM VF IR TRR CJ RθJA TJ,TSTG 30.0 1.10 5.0 50.0 2.5 12 30.0 -55 to +150 A V µA µA µs pF °C/ W °C Maximum Reverse Recovery Time(Note 1) T J =25°C Typical Junction Capacitance (Note 2) Maximum Thermal Resistance(Note 3) R θ JA Operating and Storage Temperature Range NOTES:1. Reverse Recovery Test Conditions: I F =0.5A, I R =1.0A, I rr =0.25A 2. Measured at 1 MHz and applied V r = 4.0 volts. 3. 8.0 mm 2 ( .013mm thick ) land areas. RATING AND CHARACTERISTIC CURVES INSTANTANEOUS FORWARD CURRENT, AMPERES 150 100 40 20 10 4.0 2.0 1.0 3.0 AVERAGE FORWARD CURRENT AMPERES 2.5 2.0 1.5 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD P.C.B MOUNTED ON 0.315 X 0.315" ( 8.0 X 8.0mm ) COPPER PAD AREAS 1.0 0.5 0.4 0.2 0.1 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 0 50 O 100 TEMPERATURE C Fig. 1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 100 INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 2- TYPICAL INSTANTANEOUS FORWARD CHARACTERISITCS PER ELEMENT 30 10 T J =100 C O FPRWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) 25 T J =75 OC 1.0 20 15 0.1 T J =25 OC 0.01 10 5 0 1 2 6 10 20 40 60 100 0.001 NO. OF CYCLES AT 62Hz 0 20 40 60 80 100 120 140 PERCENT OF PEAK REVERSE VOLTAGE Fig. 3- TYPICAL REAK REVERSE CHARACTERISTICS 100 Fig. 4- MAXIMUM NON-REPETITEVE PEAK FORWARD SURGE CURRENT 100 THERMAL IMPEDANCE( OC/W) 50 50 20 CAPACITANCE, pF Tj=25 C f=1.0MHz Vsig=50mVp-p 20 O 10 Units Mounted On 20in (5.4mm ) +0.5mil inches(0.013mm) Thick Copper Land Areas 2 2 10 5 5 2 1 0.01 2 0.1 1.0 10 100 1 0.1 HEATING TIME(SEC) Fig. 5- TRANSIENT THERMAL IMPEDANCE 1.0 10 100 1000 REVERSE VOLTAGE, VOLTS Fig. 6- TYPICL JUNCTION CAPACITANCE PER ELEMENT