501BMILF

DATASHEET ICS501B LOCO™ PLL CLOCK MULTIPLIER Description Features The ICS501B LOCOTM is the most cost effective way to generate a high-quality clock output from a lower frequency crystal or clock input. The name LOCO stands for Low Cost Oscillator, as it is designed to replace crystal oscillators in most electronic systems. Using Phase-Locked Loop (PLL) techniques, the device uses a standard fundamental mode, inexpensive crystal to produce output clocks up to 15 MHz. • • • • • • • • • • • • • • • Stored in the chip’s ROM is the ability to generate nine different multiplication factors, allowing one chip to output many common frequencies (see table on page 2). The device also has an output enable pin which tri-states the clock output when the OE pin is taken low. This product is intended for clock generation. It has low output jitter (variation in the output period), but input to output skew and jitter are not defined or guaranteed. For applications which require defined input to output skew, use the ICS570B. Packaged as 8 pin SOIC or die Pb (lead) free package IDT’s lowest cost PLL clock Zero ppm multiplication error Output clock frequencies up to 15 MHz Extremely low jitter of 25 ps (one sigma) Compatible with popular CPUs Duty cycle of 45/55 up to 20 MHz Nine selectable frequencies Operating voltage of 3.3 V or 5.5 V Tri-state output for board level testing 25 mA drive capability at TTL levels Ideal for oscillator replacement Industrial temperature version available Advanced, low-power CMOS process Block Diagram VDD S1:0 2 PLL Clock Multiplier Circuitry and ROM X1/ICLK Crystal or Clock input Crystal Oscillator CLK X2 Optional crystal capacitors GND IDT® LOCO™ PLL CLOCK MULTIPLIER 1 OE ICS501B REV G 011012 ICS501B LOCO™ PLL CLOCK MULTIPLIER CLOCK MULTIPLIER Pin Assignment Clock Output Table S1 S0 CLK Minimum Input 0 0 4X input 0.5 MHz X1/ I CLK 1 8 X2 0 M 5.3125X input 1 MHz VDD 2 7 OE 0 1 5X input 0.5 MHz GND 3 6 S0 M 0 6.25X input 0.5 MHz M M 2X input 1 MHz M 1 3.125X input 1 MHz 1 0 6X input 0.5MHz 1 M 3X input 0.5MHz 1 1 8X input 0.5MHz S1 5 4 CLK 8 Pi n ( 150 mi l ) SOI C 0 = connect directly to ground 1 = connect directly to VDD M = leave unconnected (floating) Pin Descriptions Pin Number Pin Name Pin Type 1 XI/ICLK Input Crystal connection or clock input. 2 VDD Power Connect to +3.3 V or +5 V. 3 GND Power Connect to ground. 4 S1 Tri-level Iinput 5 CLK Output 6 S0 Tri-level Input 7 OE Input 8 X2 Output IDT® LOCO™ PLL CLOCK MULTIPLIER Pin Description Select 1 for output clock. Connect to GND or VDD or float. Clock output per table above. Select 0 for output clock. Connect to GND or VDD or float. Output enable. Tri-states CLK output when low. Internal pull-up. Crystal connection. Leave unconnected for clock input. 2 ICS501B REV G 011012 ICS501B LOCO™ PLL CLOCK MULTIPLIER CLOCK MULTIPLIER External Components parallel resonant, fundamental mode crystal should be used. The device crystal connections should include pads for small capacitors from X1 to ground and from X2 to ground. These capacitors are used to adjust the stray capacitance of the board to match the nominally required crystal load capacitance. Because load capacitance can only be increased in this trimming process, it is important to keep stray capacitance to a minimum by using very short PCB traces (and no vias) between the crystal and device. Crystal capacitors, if needed, must be connected from each of the pins X1 and X2 to ground. Decoupling Capacitor As with any high-performance mixed-signal IC, the ICS501B must be isolated from system power supply noise to perform optimally. A decoupling capacitor of 0.01µF must be connected between VDD and the GND. It must be connected close to the ICS501B to minimize lead inductance. No external power supply filtering is required for the ICS501B. The value (in pF) of these crystal caps should equal (CL -12 pF)*2. In this equation, CL= crystal load capacitance in pF. Example: For a crystal with a 16 pF load capacitance, each crystal capacitor would be 8 pF [(16-12) x 2] = 8. Series Termination Resistor A 33Ω terminating resistor can be used next to the CLK pin for trace lengths over one inch. Crystal Load Capacitors The total on-chip capacitance is approximately 12 pF. A Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS501B. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature -40 to +85° C Storage Temperature -65 to +150° C Soldering Temperature 260° C Recommended Operation Conditions Parameter Min. Ambient Operating Temperature Power Supply Voltage (measured in respect to GND) IDT® LOCO™ PLL CLOCK MULTIPLIER 3 Typ. Max. Units 0 +70 °C +3.14 +5.25 V ICS501B REV G 011012 ICS501B LOCO™ PLL CLOCK MULTIPLIER CLOCK MULTIPLIER DC Electrical Characteristics VDD=5.0 V ±5% , Ambient temperature 0 to +70° C, unless stated otherwise Parameter Operating Voltage Symbol Conditions VDD Min. Typ. 3.14 Input High Voltage, ICLK only VIH ICLK (pin 1) Input Low Voltage, ICLK only VIL ICLK (pin 1) Input High Voltage VIH OE (pin 7) Input Low Voltage VIL OE (pin 7) Input High Voltage VIH S0, S1 Input Low Voltage VIL S0, S1 Output High Voltage VOH IOH = -25 mA Output Low Voltage VOL IOL = 25 mA Max. Units 5.25 V (VDD/2)+1 V (VDD/2)-1 2.0 V V 0.8 VDD-0.5 V V 0.5 2.4 V V 0.4 V IDD Operating Supply Current No load 20 mA Short Circuit Current CLK output +70 mA On-Chip Pull-up Resistor Pin 7 270 kΩ Input Capacitance, S1, S0, and OE Pins 4, 6, 7 4 pF 20 Ω Nominal Output Impedance IDT® LOCO™ PLL CLOCK MULTIPLIER 4 ICS501B REV G 011012 ICS501B LOCO™ PLL CLOCK MULTIPLIER CLOCK MULTIPLIER AC Electrical Characteristics VDD = 5.0 V ±5%, Ambient Temperature 0 to +70° C, unless stated otherwise Parameter Symbol Input Frequency, crystal input FIN Input Frequency, clock input FIN Output Frequency, VDD = 5.0 V ±5% Output Frequency, VDD = 3.3 V ±5% FOUT FOUT Conditions Min. Typ. Max. Units 7.5 MHz 0.5 7.5 MHz 0° C to +70° C 4 15 MHz -40° C to +85° C 4 15 MHz 0° C to +70° C 4 15 MHz -40° C to +85° C 4 15 MHz Output Clock Rise Time tOR 0.8 to 2.0 V, Note 1 1 ns Output Clock Fall Time tOF 2.0 to 8.0 V, Note 1 1 ns Output Clock Duty Cycle tOD 1.5 V, up to 25 MHz PLL Bandwidth 45 49-51 10 55 % kHz Output Enable Time, OE high to output on 50 ns Output Disable Time, OE low to tri-state 50 ns Absolute Clock Period Jitter tja Deviation from mean, Note 1 +70 ps One Sigma Clock Period Jitter tjs Note 1 25 ps Note 1: Measured with 15 pF load. IDT® LOCO™ PLL CLOCK MULTIPLIER 5 ICS501B REV G 011012 ICS501B LOCO™ PLL CLOCK MULTIPLIER CLOCK MULTIPLIER Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Narrow Body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters Inches 8 Symbol E Min A A1 B C D E e H h L α H INDEX AREA 1 2 D A Max Min 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.25 0.50 0.40 1.27 0° 8° Max .0532 .0688 .0040 .0098 .013 .020 .0075 .0098 .1890 .1968 .1497 .1574 0.050 BASIC .2284 .2440 .010 .020 .016 .050 0° 8° h x 45 A1 C -Ce SEATING PLANE B L .10 (.004) C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature 501BMILF 501BMILFT 501BMIL 501BMIL Tubes Tape and Reel 8-pin SOIC 8-pin SOIC -40 to +85° C -40 to +85° C “LF” denotes Pb (lead) free package. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT® LOCO™ PLL CLOCK MULTIPLIER 6 ICS501B REV G 011012 ICS501B LOCO™ PLL CLOCK MULTIPLIER CLOCK MULTIPLIER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2012 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.