128K x 36, 256K x 18
3.3V Synchronous SRAMs
3.3V I/O, Pipelined Outputs
Burst Counter, Single Cycle Deselect
Features
◆
◆
◆
◆
◆
128K x 36, 256K x 18 memory configurations
Supports high system speed:
Commercial and Industrial:
– 150MHz 3.8ns clock access time
– 133MHz 4.2ns clock access time
LBO input selects interleaved or linear burst mode
Self-timed write cycle with global write control (GW), byte write
enable (BWE), and byte writes (BWx)
◆
◆
◆
◆
◆
71V3576S
71V3578S
3.3V core power supply
Power down controlled by ZZ input
3.3V I/O
Packaged in a JEDEC Standard 100-pin plastic thin quad
flatpack (TQFP)
Industrial temperature range (–40°C to +85°C) is available
for selected speeds
Green parts available, see ordering information
Functional Block Diagram
LBO
ADV
CLK
2
Binary
Counter
ADSC
INTERNAL
ADDRESS
Burst
Sequence
CEN
Burst
Logic
Q0
CLR
ADSP
17/18
A0*
Q1
CLK EN
ADDRESS
REGISTER
A0 - A16/17
GW
BWE
A1*
128K x 36/
256K x 18BIT
MEMORY
ARRAY
2
A0,A1
A2–A17
36/18
17/18
Byte 1
Write Register
36/18
Byte 1
Write Driver
BW1
9
Byte 2
Write Register
Byte 2
Write Driver
BW2
9
Byte 3
Write Register
Byte 3
Write Driver
BW3
9
Byte 4
Write Register
Byte 4
Write Driver
BW4
9
OUTPUT
REGISTER
D
CS0
CS1
Q
Enable
Register
DATA
INPUT
REGISTER
CLK EN
ZZ
Powerdown
D
Q
Enable
Delay
Register
OE
OE
I/O0 — I/O31
I/OP1 — I/OP4
OUTPUT
BUFFER
36/18
5279 drw 01
1
May.01.20
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
Description
The IDT71V3576/78 are high-speed SRAMs organized as
128K x 36/256K x 18. The IDT71V3576/78 SRAMs contain write, data,
address and control registers. Internal logic allows the SRAM to generate
a self-timed write based upon a decision which can be left until the end of
the write cycle.
The burst mode feature offers the highest level of performance to the
system designer, as the IDT71V3576/78 can provide four cycles of data
for a single address presented to the SRAM. An internal burst address
counter accepts the first cycle address from the processor, initiating the
access sequence. The first cycle of output data will be pipelined for one
cycle before it is available on the next rising clock edge. If burst mode
operation is selected (ADV=LOW), the subsequent three cycles of output
data will be available to the user on the next three rising clock edges. The
order of these three addresses are defined by the internal burst counter
and the LBO input pin.
The IDT71V3576/78 SRAMs utilize a high-performance CMOS
process and are packaged in a JEDEC standard 14mm x 20mm 100-pin
thin plastic quad flatpack (TQFP).
Pin Description Summary
A0-A17
Address Inputs
Input
Synchronous
CE
Chip Enable
Input
Synchronous
CS0, CS1
Chip Selects
Input
Synchronous
OE
Output Enable
Input
Asynchronous
GW
Global Write Enable
Input
Synchronous
Byte Write Enable
Input
Synchronous
BW1, BW2, BW3, BW4
Individual Byte Write Selects
Input
Synchronous
CLK
Clock
Input
N/A
ADV
Burst Address Advance
Input
Synchronous
ADSC
Address Status (Cache Controller)
Input
Synchronous
ADSP
Address Status (Processor)
Input
Synchronous
LBO
Linear / Interleaved Burst Order
Input
DC
ZZ
Sleep Mode
Input
Asynchronous
I/O0-I/O31, I/OP1-I/OP4
Data Input / Output
I/O
Synchronous
VDD, VDDQ
Core Power, I/O Power
Supply
N/A
VSS
Ground
Supply
N/A
BWE
(1)
5279 tbl 01
NOTE:
1. BW3 and BW4 are not applicable for the IDT71V3578.
6.42
2
May.01.20
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Pin Definitions
Commercial and Industrial Temperature Ranges
(1)
Symbol
Pin Function
I/O
Active
Description
A0-A17
Address Inputs
I
N/A
Synchronous Address inputs. The address register is triggered by a combination of the rising edge
of CLK and ADSC Low or ADSP Low and CE Low.
ADSC
Address Status
(Cache Controller)
I
LOW
Synchronous Address Status from Cache Controller. ADSC is an active LOW input that is used to load
the address registers with new addresses.
ADSP
Address Status
(Processor)
I
LOW
Synchronous Address Status from Processor. ADSP is an active LOW input that is used to load the
address registers with new addresses. ADSP is gated by CE.
ADV
Burst Address
Advance
I
LOW
Synchronous Address Advance. ADV is an active LOW input that is used to advance the internal
burst counter, controlling burst access after the initial address is loaded. When the input is HIGH the
burst counter is not incremented; that is, there is no address advance.
BWE
Byte Write Enable
I
LOW
Synchronous byte write enable gates the byte write inputs BW1-BW4. If BWE is LOW at the rising
edge of CLK then BWx inputs are passed to the next stage in the circuit. If BWE is HIGH then the
byte write inputs are blocked and only GW can initiate a write cycle.
BW1-BW4
Individual Byte
Write Enables
I
LOW
Synchronous byte write enables. BW1 controls I/O0-7, I/OP1, BW2 controls I/O8-15, I/OP2, etc. Any
active byte write causes all outputs to be disabled.
CE
Chip Enable
I
LOW
Synchronous chip enable. CE is used with CS 0 and CS1 to enable the IDT71V3576/78. CE also gates
ADSP.
CLK
Clock
I
N/A
This is the clock input. All timing references for the device are made with respect to this input.
CS0
Chip Select 0
I
HIGH
Synchronous active HIGH chip select. CS 0 is used with CE and CS1 to enable the chip.
CS1
Chip Select 1
I
LOW
Synchronous active LOW chip select. CS1 is used with CE and CS0 to enable the chip.
GW
Global Write
Enable
I
LOW
Synchronous global write enable. This input will write all four 9-bit data bytes when LOW on the rising
edge of CLK. GW supersedes individual byte write enables.
I/O0-I/O31
I/OP1-I/OP4
Data Input/Output
I/O
N/A
Synchronous data input/output (I/O) pins. Both the data input path and data output path are registered
and triggered by the rising edge of CLK.
LBO
Linear Burst Order
I
LOW
Asynchronous burst order selection input. When LBO is HIGH, the interleaved burst sequence is
selected. When LBO is LOW the Linear burst sequence is selected. LBO is a static input and must
not change state while the device is operating.
OE
Output Enable
I
LOW
Asynchronous output enable. When OE is LOW the data output drivers are enabled on the I/O pins if
the chip is also selected. When OE is HIGH the I/O pins are in a high-impedance state.
ZZ
Sleep Mode
I
HIGH
Asynchronous sleep mode input. ZZ HIGH will gate the CLK internally and power down the
IDT71V3576/78 to its lowest power consumption level. Data retention is guaranteed in Sleep
Mode.This pin has an internal pull down.
VDD
Power Supply
N/A
N/A
3.3V core power supply.
VDDQ
Power Supply
N/A
N/A
3.3V I/O Supply.
VSS
Ground
N/A
N/A
Ground.
NC
No Connect
N/A
N/A
NC pins are not electrically connected to the device.
5279 tbl 02
NOTE:
1. All synchronous inputs must meet specified setup and hold times with respect to CLK.
6.42
3
May.01.20
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Absolute Maximum Ratings(1)
Symbol
Rating
(2)
Recommended Operating
Temperature and Supply Voltage
Commercial &
Industrial
Unit
Grade
Temperature(1)
VSS
VDD
VDDQ
Commercial
0°C to +70°C
0V
3.3V±5%
3.3V±5%
Industrial
-40°C to +85°C
0V
3.3V±5%
3.3V±5%
VTERM
Terminal Voltage with
Respect to GND
-0.5 to +4.6
V
VTERM(3,6)
Terminal Voltage with
Respect to GND
-0.5 to VDD
V
VTERM(4,6)
Terminal Voltage with
Respect to GND
-0.5 to VDD +0.5
V
VTERM(5,6)
Terminal Voltage with
Respect to GND
-0.5 to VDDQ +0.5
V
Commercial
Operating Temperature
-0 to +70
o
C
Industrial
Operating Temperature
-40 to +85
o
C
Temperature
Under Bias
-55 to +125
o
C
TA
(7)
TBIAS
TSTG
Storage
Temperature
PT
Power Dissipation
2.0
W
IOUT
DC Output Current
50
mA
-55 to +125
o
Recommended DC Operating
Conditions
Symbol
Input Capacitance
CI/O
I/O Capacitance
Typ.
Max.
Unit
3.135
3.3
3.465
V
VDDQ
I/O Supply Voltage
3.135
3.3
3.465
V
0
0
0
V
C
VSS
Supply Voltage
VIH
Input High Voltage - Inputs
2.0
____
VDD +0.3
V
VIH
Input High Voltage - I/O
2.0
____
VDDQ +0.3(1)
V
VIL
Input Low Voltage
-0.3(2)
____
0.8
V
5279 tbl 06
NOTES:
1. VIH (max) = VDDQ + 1.0V for pulse width less than tCYC/2, once per cycle.
2. VIL (min) = -1.0V for pulse width less than tCYC/2, once per cycle.
Conditions
Max.
Unit
VIN = 3dV
5
pF
VOUT = 3dV
7
pF
5279 tbl 07
NOTE:
1. This parameter is guaranteed by device characterization, but not production tested.
6.42
4
May.01.20
Min.
Core Supply Voltage
(TA = +25°C, f = 1.0MHz)
CIN
Parameter
VDD
100 Pin TQFP Capacitance
Parameter(1)
5279 tbl 04
NOTE:
1. TA is the "instant on" case temperature.
5279 tbl 03
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated
in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.
2. VDD terminals only.
3. VDDQ terminals only.
4. Input terminals only.
5. I/O terminals only.
6. This is a steady-state DC parameter that applies after the power supplies have
ramped up. Power supply sequencing is not necessary; however, the voltage
on any input or I/O pin cannot exceed VDDQ during power supply ramp up.
7. TA is the "instant on" case temperature.
Symbol
Commercial and Industrial Temperature Ranges
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
A6
A7
CE
CS0
BW4
BW3
BW2
BW1
CS1
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A8
A9
Pin Configuration – 128K x 36, PKG100
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
I/OP3
I/O16
I/O17
VDDQ
VSS
I/O18
I/O19
I/O20
I/O21
VSS
VDDQ
I/O22
I/O23
VDD / NC(1)
VDD
NC
VSS
I/O24
I/O25
VDDQ
VSS
I/O26
I/O27
I/O28
I/O29
VSS
VDDQ
I/O30
I/O31
I/OP4
1
80
2
79
3
78
4
77
5
76
6
75
7
74
8
73
9
10
71V3576
(3)
PKG100
11
12
72
71
70
69
13
68
14
67
15
66
16
65
64
17
18
19
63
62
20
61
21
60
22
59
23
24
58
57
25
56
26
55
27
54
53
28
29
52
51
30
I/OP2
I/O15
I/O14
VDDQ
VSS
I/O13
I/O12
I/O11
I/O10
VSS
VDDQ
I/O9
I/O8
VSS
NC
VDD
ZZ(2)
I/O7
I/O6
VDDQ
VSS
I/O5
I/O4
I/O3
I/O2
VSS
VDDQ
I/O1
I/O0
I/OP1
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
NC
NC
VSS
VDD
NC
NC
A10
A11
A12
A13
A14
A15
A16
LBO
A5
A4
A3
A2
A1
A0
5279 drw 02
100 TQFP
Top View
NOTES:
1. Pin 14 can either be directly connected to VDD, or connected to an input voltage ≥ VIH, or left unconnected.
2. Pin 64 can be left unconnected and the device will always remain in active mode.
3. This text does not indicate orientation of actual part-marking.
6.42
5
May.01.20
,
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
CS0
NC
NC
BW2
BW1
CS1
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A8
A9
A6
A7
CE
Pin Configuration – 256K x 18, PKG100
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
NC
NC
NC
1
80
2
79
3
78
VDDQ
VSS
NC
NC
I/O8
I/O9
VSS
VDDQ
I/O10
I/O11
VDD / NC(1)
VDD
NC
VSS
I/O12
I/O13
VDDQ
VSS
I/O14
I/O15
I/OP2
NC
VSS
VDDQ
NC
NC
NC
4
77
5
76
6
75
7
74
8
73
9
72
71
10
11
12
13
71V3578
(3)
PKG100
70
69
68
14
67
15
66
16
65
64
17
18
19
63
62
20
61
21
60
22
59
23
24
58
57
25
56
26
55
27
54
53
28
29
52
51
30
A10
NC
NC
VDDQ
VSS
NC
I/OP1
I/O7
I/O6
VSS
VDDQ
I/O5
I/O4
VSS
NC
VDD
ZZ(2)
I/O3
I/O2
VDDQ
VSS
I/O1
I/O0
NC
NC
VSS
VDDQ
NC
NC
NC
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
LBO
A5
A4
A3
A2
A1
A0
NC
NC
VSS
VDD
NC
NC
A11
A12
A13
A14
A15
A16
A17
5279 drw 03
100 TQFP
Top View
NOTES:
1. Pin 14 can either be directly connected to VDD, or connected to an input voltage ≥ VIH, or left unconnected.
2. Pin 64 can be left unconnected and the device will always remain in active mode.
3. This text does not indicate orientation of actual part-marking.
6.42
6
May.01.20
,
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range (VDD = 3.3V ± 5%)
Symbol
Parameter
Test Conditions
Min.
Max.
Unit
5
µA
|ILI|
Input Leakage Current
VDD = Max., VIN = 0V to VDD
___
|ILZZ|
ZZ and LBO Input Leakage Current(1)
VDD = Max., VIN = 0V to VDD
___
30
µA
|ILO|
Output Leakage Current
VOUT = 0V to VDDQ, Device Deselected
___
5
µA
VOL
Output Low Voltage
IOL = +8mA, VDD = Min.
___
0.4
V
VOH
Output High Voltage
IOH = -8mA, VDD = Min.
2.4
___
V
5279 tbl 08
NOTE:
1. The LBO pin will be internally pulled to VDD and the ZZ pin will be internally pulled to VSS if they are not actively driven in the application.
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range(1)
150MHz
Symbol
Parameter
Test Conditions
133MHz
Com'l
Ind
Com'l
Ind
Unit
IDD
Operating Power Supply
Current
Device Selected, Outputs Open, VDD = Max.,
VDDQ = Max., VIN > VIH or < VIL, f = fMAX(2)
295
305
250
260
mA
ISB1
CMOS Standby Power
Supply Current
Device Deselected, Outputs Open, V DD = Max.,
VDDQ = Max., VIN > VHD or < VLD, f = 0(2,3)
30
35
30
35
mA
ISB2
Clock Running Power
Supply Current
Device Deselected, Outputs Open, V DD = Max.,
VDDQ = Max., VIN > VHD or < VLD, f = fMAX(2,3)
105
115
100
110
mA
IZZ
Full Sleep Mode Supply
Current
ZZ > VHD, VDD = Max.
30
35
30
35
mA
5279 tbl 09
NOTES:
1. All values are maximum guaranteed values.
2. At f = fMAX, inputs are cycling at the maximum frequency of read cycles of 1/tCYC while ADSC = LOW; f=0 means no input lines are changing.
3. For I/Os VHD = VDDQ - 0.2V, VLD = 0.2V. For other inputs VHD = VDD - 0.2V, VLD = 0.2V.
AC Test Conditions
AC Test Load
(VDDQ = 3.3V)
Input Pulse Levels
50Ω
0 to 3V
I/O
Input Rise/Fall Times
2ns
Input Timing Reference Levels
1.5V
Output Timing Reference Levels
1.5V
6
See Figure 1
5
AC Test Load
VDDQ/2
Z0 = 50Ω
5279 drw 06
,
Figure 1. AC Test Load
5279 tbl 10
4
ΔtCD 3
(Typical, ns)
2
1
20 30 50
80 100
Capacitance (pF)
Figure 2. Lumped Capacitive Load, Typical Derating
6.42
7
May.01.20
200
5279 drw 07
,
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
Synchronous Truth Table(1,3)
Address
Used
CE
CS0
CS1
ADSP
ADSC
ADV
GW
BWE
BWx
OE
(2)
CLK
I/O
Deselected Cycle, Power Down
None
H
X
X
X
L
X
X
X
X
X
-
HI-Z
Deselected Cycle, Power Down
None
L
X
H
L
X
X
X
X
X
X
-
HI-Z
Deselected Cycle, Power Down
None
L
L
X
L
X
X
X
X
X
X
-
HI-Z
Deselected Cycle, Power Down
None
L
X
H
X
L
X
X
X
X
X
-
HI-Z
Deselected Cycle, Power Down
None
L
L
X
X
L
X
X
X
X
X
-
HI-Z
Read Cycle, Begin Burst
External
L
H
L
L
X
X
X
X
X
L
-
DOUT
Read Cycle, Begin Burst
External
L
H
L
L
X
X
X
X
X
H
-
HI-Z
Read Cycle, Begin Burst
External
L
H
L
H
L
X
H
H
X
L
-
DOUT
Read Cycle, Begin Burst
External
L
H
L
H
L
X
H
L
H
L
-
DOUT
Read Cycle, Begin Burst
External
L
H
L
H
L
X
H
L
H
H
-
HI-Z
Write Cycle, Begin Burst
External
L
H
L
H
L
X
H
L
L
X
-
DIN
Write Cycle, Begin Burst
External
L
H
L
H
L
X
L
X
X
X
-
DIN
Read Cycle, Continue Burst
Next
X
X
X
H
H
L
H
H
X
L
-
DOUT
Read Cycle, Continue Burst
Next
X
X
X
H
H
L
H
H
X
H
-
HI-Z
Read Cycle, Continue Burst
Next
X
X
X
H
H
L
H
X
H
L
-
DOUT
Read Cycle, Continue Burst
Next
X
X
X
H
H
L
H
X
H
H
-
HI-Z
Read Cycle, Continue Burst
Next
H
X
X
X
H
L
H
H
X
L
-
DOUT
Read Cycle, Continue Burst
Next
H
X
X
X
H
L
H
H
X
H
-
HI-Z
Read Cycle, Continue Burst
Next
H
X
X
X
H
L
H
X
H
L
-
DOUT
Read Cycle, Continue Burst
Next
H
X
X
X
H
L
H
X
H
H
-
HI-Z
Write Cycle, Continue Burst
Next
X
X
X
H
H
L
H
L
L
X
-
DIN
Write Cycle, Continue Burst
Next
X
X
X
H
H
L
L
X
X
X
-
DIN
Write Cycle, Continue Burst
Next
H
X
X
X
H
L
H
L
L
X
-
DIN
Write Cycle, Continue Burst
Next
H
X
X
X
H
L
L
X
X
X
-
DIN
Read Cycle, Suspend Burst
Current
X
X
X
H
H
H
H
H
X
L
-
DOUT
Read Cycle, Suspend Burst
Current
X
X
X
H
H
H
H
H
X
H
-
HI-Z
Read Cycle, Suspend Burst
Current
X
X
X
H
H
H
H
X
H
L
-
DOUT
Read Cycle, Suspend Burst
Current
X
X
X
H
H
H
H
X
H
H
-
HI-Z
Read Cycle, Suspend Burst
Current
H
X
X
X
H
H
H
H
X
L
-
DOUT
Read Cycle, Suspend Burst
Current
H
X
X
X
H
H
H
H
X
H
-
HI-Z
Read Cycle, Suspend Burst
Current
H
X
X
X
H
H
H
X
H
L
-
DOUT
Read Cycle, Suspend Burst
Current
H
X
X
X
H
H
H
X
H
H
-
HI-Z
Write Cycle, Suspend Burst
Current
X
X
X
H
H
H
H
L
L
X
-
DIN
Write Cycle, Suspend Burst
Current
X
X
X
H
H
H
L
X
X
X
-
DIN
Write Cycle, Suspend Burst
Current
H
X
X
X
H
H
H
L
L
X
-
DIN
Write Cycle, Suspend Burst
Current
H
X
X
X
H
H
L
X
X
X
-
Operation
NOTES:
1. L = VIL, H = VIH, X = Don’t Care.
2. OE is an asynchronous input.
3. ZZ = low for this table.
6.42
8
May.01.20
DIN
5279 tbl 11
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
Synchronous Write Function Truth Table(1, 2)
Operation
GW
BWE
BW1
BW2
BW3
BW4
Read
H
H
X
X
X
X
Read
H
L
H
H
H
H
Write all Bytes
L
X
X
X
X
X
Write all Bytes
H
L
L
L
L
L
(3)
H
L
L
H
H
H
(3)
H
L
H
L
H
H
(3)
H
L
H
H
L
H
(3)
H
L
H
H
H
L
Write Byte 1
Write Byte 2
Write Byte 3
Write Byte 4
5279 tbl 12
NOTES:
1. L = VIL, H = VIH, X = Don’t Care.
2. BW3 and BW4 are not applicable for the IDT71V3578.
3. Multiple bytes may be selected during the same cycle.
Asynchronous Truth Table(1)
Operation(2)
OE
ZZ
I/O Status
Power
Read
L
L
Data Out
Active
Read
H
L
High-Z
Active
Write
X
L
High-Z – Data In
Active
Deselected
X
L
High-Z
Standby
Sleep Mode
X
H
High-Z
Sleep
5279 tbl 13
NOTES:
1. L = VIL, H = VIH, X = Don’t Care.
2. Synchronous function pins must be biased appropriately to satisfy operation requirements.
Interleaved Burst Sequence Table (LBO=VDD)
Sequence 1
Sequence 2
Sequence 3
Sequence 4
A1
A0
A1
A0
A1
A0
A1
A0
First Address
0
0
0
1
1
0
1
1
Second Address
0
1
0
0
1
1
1
0
Third Address
1
0
1
1
0
0
0
1
1
1
1
0
0
1
0
0
Fourth Address
(1)
5279 tbl 14
NOTE:
1. Upon completion of the Burst sequence the counter wraps around to its initial state.
Linear Burst Sequence Table (LBO=VSS)
Sequence 1
Sequence 2
Sequence 3
Sequence 4
A1
A0
A1
A0
A1
A0
A1
A0
First Address
0
0
0
1
1
0
1
1
Second Address
0
1
1
0
1
1
0
0
Third Address
1
0
1
1
0
0
0
1
Fourth Address (1)
1
1
0
0
0
1
1
0
NOTE:
1. Upon completion of the Burst sequence the counter wraps around to its initial state.
6.42
9
May.01.20
5279 tbl 15
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
AC Electrical Characteristics
(VDD = 3.3V ±5%, Commercial and Industrial Temperature Ranges)
150MHz
Symbol
Parameter
133MHz
Min.
Max.
Min.
Max.
Unit
tCYC
Clock Cycle Time
6.7
____
7.5
____
ns
tCH(1)
Clock High Pulse Width
2.6
____
3
____
ns
tCL(1)
Clock Low Pulse Width
2.6
____
3
____
ns
Output Parameters
tCD
Clo ck High to Valid Data
____
3.8
____
4.2
ns
tCDC
Clock High to Data Change
1.5
____
1.5
____
ns
tCLZ(2)
Clock High to Output Active
0
____
0
____
ns
tCHZ(2)
Clock High to Data High-Z
1.5
3.8
1.5
4.2
ns
tOE
Output Enable Access Time
____
3.8
____
4.2
ns
tOLZ(2)
Output Enable Low to Output Active
0
____
0
____
ns
tOHZ(2)
Output Enable High to Output High-Z
____
3.8
____
4.2
ns
tSA
Address Setup Time
1.5
____
1.5
____
ns
tSS
Address Status Setup Time
1.5
____
1.5
____
ns
tSD
Data In Setup Time
1.5
____
1.5
____
ns
tSW
Write Setup Time
1.5
____
1.5
____
ns
tSAV
Address Advance Setup Time
1.5
____
1.5
____
ns
tSC
Chip Enable/Select Setup Time
1.5
____
1.5
____
ns
tHA
Address Hold Time
0.5
____
0.5
____
ns
tHS
Address Status Hold Time
0.5
____
0.5
____
ns
tHD
Data In Hold Time
0.5
____
0.5
____
ns
tHW
Write Hold Time
0.5
____
0.5
____
ns
tHAV
Address Advance Hold Time
0.5
____
0.5
____
ns
tHC
Chip Enable/Select Hold Time
0.5
____
0.5
____
ns
Set Up Times
Hold Times
Sleep Mode and Configuration Parameters
tZZPW
ZZ Pulse Width
100
____
100
____
ns
tZZR(3)
ZZ Recovery Time
100
____
100
____
ns
tCFG (4)
Configuration Set-up Time
27
____
30
____
ns
NOTES:
1. Measured as HIGH above VIH and LOW below VIL.
2. Transition is measured ±200mV from steady-state.
3. Device must be deselected when powered-up from sleep mode.
4. tCFG is the minimum time required to configure the device based on the LBO input. LBO is a static input and must not change during normal operation.
6.42
10
May.01.20
5279 tbl 16
May.01.20
6.42
11
Output
Disabled
tSC
tSA
tSS
tHS
Ax
Pipelined
Read
tOLZ
tOE
tHC
tHA
O1(Ax)
Ay
(1)
tCH
tCLZ
tOHZ
tCD
tSW
tCL
tSAV
O1(Ay)
tCDC
tHAV
O2(Ay)
tHW
Burst Pipelined Read
O3(Ay)
ADV HIGH suspends
burst
O4(Ay)
(Burst wraps around
to its initial state)
O1(Ay)
tCHZ
O2(Ay)
5279 drw 08
,
NOTES:
1. O1 (Ax) represents the first output from the external address Ax. O1 (Ay) represents the first output from the external address Ay; O2 (Ay) represents the next output data in the burst sequence
of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input.
2. ZZ input is LOW and LBO is Don't Care for this cycle.
3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH.
DATAOUT
OE
ADV
(Note 3)
CE, CS1
GW,BWE,BWx
ADDRESS
ADSC
ADSP
CLK
tCYC
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
Timing Waveform of Pipelined Read Cycle(1,2)
May.01.20
6.42
12
tSA
tHA
tSS
tHS
tCLZ
tCD
Single Read
Ax
(2)
tOE
O1(Ax)
tOHZ
tSW
Ay
tCH
Pipelined
Write
I1(Ay)
tSD tHD
tCL
tHW
Az
tOLZ
tCD
O2(Az)
Pipelined Burst Read
O1(Az)
tCDC
5279 drw 09
O3(Az)
,
NOTES:
1. Device is selected through entire cycle; CE and CS1 are LOW, CS0 is HIGH.
2. ZZ input is LOW and LBO is Don't Care for this cycle.
3. O1 (Ax) represents the first output from the external address Ax. I1 (Ay) represents the first input from the external address Ay; O1 (Az) represents the first output from the external address Az; O2 (Az) represents
the next output data in the burst sequence of the base address Az, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input.
DATAOUT
DATAIN
OE
ADV
GW
ADDRESS
ADSP
CLK
tCYC
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
Timing Waveform of Combined Pipelined Read and Write Cycles(1,2,3)
May.01.20
6.42
13
O4(Aw)
Ax
Burst Read
tHC
O3(Aw)
tSC
tSA
tHA
tSS
tHS
Ay
tCL
Single
Write
tOHZ
I1(Ax)
I1(Ay)
I2(Ay)
Burst Write
I2(Ay)
(ADV HIGH suspends burst)
tSAV
GW is ignored when ADSP initiates a cycle and is sampled on the next clock rising edge
tCH
I3(Ay)
tHAV
I4(Ay)
tSD
I1(Az)
tHW
tSW
Az
I3(Az)
5279 drw 10
Burst Write
I2(Az)
tHD
NOTES:
1. ZZ input is LOW, BWE is HIGH and LBO is Don't Care for this cycle.
2. O4 (Aw) represents the final output data in the burst sequence of the base address Aw. I1 (Ax) represents the first input from the external address Ax. I1 (Ay) represents the first input from the external
address Ay; I2 (Ay) represents the next input data in the burst sequence of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined
by the state of the LBO input. In the case of input I2 (Ay) this data is valid for two cycles because ADV is high and has suspended the burst.
3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH.
DATAOUT
DATAIN
OE
ADV
(Note 3)
CE, CS1
GW
ADDRESS
ADSC
ADSP
CLK
tCYC
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
Timing Waveform of Write Cycle No. 1 - GW Controlled(1,2,3)
,
May.01.20
6.42
14
tHC
Burst
Read
O3(Aw)
tSC
tSA
tHA
tSS
tHS
O4(Aw)
Ax
Ay
tCL
Single
Write
tOHZ
I1(Ax)
I1(Ay)
Burst Write
I2(Ay)
(ADV suspends burst)
BWx is ignored when ADSP initiates a cycle and is sampled on next clock rising edge
BWE is ignored when ADSP initiates a cycle and is sampled on next clock rising edge
tCH
I2(Ay)
I3(Ay)
I4(Ay)
tSD
Extended
Burst Write
I1(Az)
tSAV
tHW
tSW
tHW
tSW
Az
I2(Az)
tHD
5279 drw 11
I3(Az)
,
NOTES:
1. ZZ input is LOW, GW is HIGH and LBO is Don't Care for this cycle.
2. O4 (Aw) represents the final output data in the burst sequence of the base address Aw. I1 (Ax) represents the first input from the external address Ax. I1 (Ay) represents the first input from the external
address Ay; I2 (Ay) represents the next input data in the burst sequence of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined
by the state of the LBO input. In the case of input I2 (Ay) this data is valid for two cycles because ADV is high and has suspended the burst.
3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH.
DATAOUT
DATAIN
OE
ADV
(Note 3)
CE, CS1
BWx
BWE
ADDRESS
ADSC
ADSP
CLK
tCYC
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
Timing Waveform of Write Cycle No. 2 - Byte Controlled(1,2,3)
May.01.20
6.42
15
tSS
tSC
tSA
tHS
Ax
Single Read
tOLZ
tOE
tHC
tHA
O1(Ax)
tCH
tCL
tZZPW
Snooze Mode
tZZR
NOTES:
1. Device must power up in deselected Mode
2. LBO is Don't Care for this cycle.
3. It is not necessary to retain the state of the input registers throughout the Power-down cycle.
4. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH.
ZZ
DATAOUT
OE
ADV
(Note 4)
CE, CS1
GW
ADDRESS
ADSC
ADSP
CLK
tCYC
Az
5279 drw 12
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
Timing Waveform of Sleep (ZZ) and Power-Down Modes(1,2,3)
,
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
Non-Burst Read Cycle Timing Waveform
CLK
ADSP
ADSC
ADDRESS
Av
Aw
Ax
Ay
Az
GW, BWE, BWx
CE, CS1
CS0
OE
(Av)
DATAOUT
(Aw)
(Ax)
(Ay)
NOTES:
1. ZZ input is LOW, ADV is HIGH and LBO is Don't Care for this cycle.
2. (Ax) represents the data for address Ax, etc.
3. For read cycles, ADSP and ADSC function identically and are therefore interchangable.
,
5279 drw 14
Non-Burst Write Cycle Timing Waveform
CLK
ADSP
ADSC
ADDRESS
Av
Aw
Ax
Ay
Az
(Ax)
(Ay)
(Az)
GW
CE, CS1
CS0
DATAIN
(Av)
(Aw)
NOTES:
1. ZZ input is LOW, ADV and OE are HIGH, and LBO is Don't Care for this cycle.
2. (Ax) represents the data for address Ax, etc.
3. Although only GW writes are shown, the functionality of BWE and BWx together is the same as GW.
4. For write cycles, ADSP and ADSC have different limitations.
6.42
16
May.01.20
,
5279 drw 15
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
Ordering Information
XXX
S
X
XX
Device
Type
Power
Speed
Package
X
X
X
Process/
Temperature
Range
Blank
8
Tray
Tape and Reel
Blank
I(1)
Commercial (0°C to +70°C)
Industrial (-40°C to +85°C)
G
Green
PF
100-pin Plastic Thin Quad Flatpack (PKG100)
150
133
Frequency in Megahertz
S
Standard Power
71V3576
71V3578
128K x 36 Pipelined Burst Synchronous SRAM with 3.3V I/O
256K x 18 Pipelined Burst Synchronous SRAM with 3.3V I/O
5279 drw 13
NOTE:
1. Contact your local sales office for Industrial temp range for other speeds, packages and powers.
Orderable Part Information
133
150
Pkg.
Code
Pkg.
Type
Temp.
Grade
71V3578S133PFG
PKG100
TQFP
C
C
71V3578S133PFG8
PKG100
TQFP
C
I
71V3578S133PFGI
PKG100
TQFP
I
71V3578S133PFGI8
PKG100
TQFP
I
71V3578S150PFG
PKG100
TQFP
C
PKG100
TQFP
C
Pkg.
Code
Pkg.
Type
Temp.
Grade
Speed
(MHz)
71V3576S133PFG
PKG100
TQFP
C
133
71V3576S133PFG8
PKG100
TQFP
71V3576S133PFGI
PKG100
TQFP
Speed
(MHz)
Orderable Part ID
Orderable Part ID
71V3576S133PFGI8
PKG100
TQFP
I
71V3576S150PFG
PKG100
TQFP
C
71V3576S150PFG8
PKG100
TQFP
C
71V3578S150PFG8
71V3576S150PFGI
PKG100
TQFP
I
71V3578S150PFGI
PKG100
TQFP
I
I
71V3578S150PFGI8
PKG100
TQFP
I
71V3576S150PFGI8
PKG100
TQFP
150
6.42
17
May.01.20
71V3576, 71V3578, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
3.3V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect
Commercial and Industrial Temperature Ranges
Datasheet Document History
7/26/99
9/17/99
12/31/99
04/04/00
Pg. 8
Pg. 11
Pg. 18
Pg. 20
Pg. 1, 8, 11, 19
Pg. 1, 4, 8, 11, 19
Pg.18
Pg. 4
Pg. 7
06/01/00
07/15/00
Pg. 20
Pg. 7
Pg. 8
Pg. 20
10/25/00
04/22/03
06/30/03
Pg. 8
Pg. 4
Pg. 1,2,3,5-9
Pg. 5-8
Pg. 19,20
Pg. 21-23
Pg. 24
01/01/04
01/20/10
02/25/12
Pg.21
Pg.1,2,4,7,8
Pg.19,20,21
Pg.1,2,3,7,17
02/08/13
Pg.1
Pg.17
12/10/15
05/01/20
Pg. 17
Pg. 1 - 19
Pg. 5 & 6
Pg. 1 & 17
Pg. 17
Updated to new format
Revised ISB1 and IZZ for speeds 100–200MHz
Revised tCDC (min.) at 166MHz
Added 119 BGA package diagram
Added Datasheet Document History
Removed 166, 183, and 200MHz speed grade offerings
(see IDT71V35761 and IDT71V35781)
Added Industrial Temperature range offerings
Added 100TQFP Package Diagram Outline
Add capacitance table for the BGA package; Add Industrial temperature to table;
Insert note to Absolute Max Rating and Recommended Operating Temperature tables
Add note to BGA pin configurations; corrected typo in pinout
Add new package offering, 13 x 15mm fBGA
Correct BG119 Package Diagram Outline
Add note reference to BG119 pinout
Add DNU reference note to BQ165 pinout
Update BG119 Package Diagram Outline Dimensions
Remove Preliminary Status
Add reference note to pin N5 on BQ165 pinout, reserved for JTAG TRST
Updated 165 BGA table information from TBD to 7
Updated datasheet with JTAG information
Removed note for NC pins (38,39(PF package); L4, U4 (BG package) H2, N7 (BQ package))
requiring NC or connection to Vss.
Added two pages of JTAG Specification, AC Electrical, Definitions and Instructions
Removed old package information from the datasheet
Updated ordering information with JTAG and Y stepping information. Added information
regarding packages available IDT website.
Added "Restricted hazardous substance device" to ordering information.
Combined S and YS datasheet into one datasheet. Deleted JTAG and packages BGA, fBGA.
Removed "IDT" from orderable part number.
Removed YS. Deleted JTAG info from Functional Block diagram and Ordering information.
Deleted JTAG pins TMS, TDI, TCK and TDO from 3 tables.Updated ordering information to
include tube or tray and tape & reel.
Removed IDT in reference to fabrication.
Updated the wording from Restricted Hazardous Substance Device to Green in the Ordering
Information.
Amended the Ordering Information drawing to restore the visibility of this information.
Rebranded as Renesas datasheet
Updated package codes
Updated Industrial temp range and Green availability
Added Orderable Part Information tables
6.42
18
May.01.20
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.