74LVCHR162245APAG8

IDT74LVCHR162245A 3.3V CMOS 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE 3.3V CMOS 16-BIT IDT74LVCHR162245A BUS TRANSCEIVER WITH 3 STATE OUTPUTS, 5 VOLT TOLERANT I/O, BUS-HOLD DESCRIPTION: FEATURES: This 16-bit bus transceiver is built using advanced dual metal CMOS technology. This high-speed, low power device is ideal for asynchronous communication between two buses (A and B). The Direction and Output Enable controls are designed to operate this device as either two independent 8-bit transceivers or one 16-bit transceiver. The direction control pin (DIR) controls the direction of data flow. The output enable pin (OE) overrides the direction control and disables both ports. All inputs are designed with hysteresis for improved noise margin. All pins can be driven from either 3.3V or 5V devices. This feature allows the use of this device as a translator in a mixed 3.3V/5V supply system. The LVCHR162245A has series resistors in the device output structure which will significantly reduce line noise when used with light loads. The driver has been designed to drive ±12mA at the designated threshold levels. The LVCHR162245A has “bus-hold” which retains the inputs' last state whenever the input goes to a high impedance. This prevents floating inputs and eliminates the need for pull-up/down resistors. • Typical tSK(o) (Output Skew) < 250ps • ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) • VCC = 3.3V ± 0.3V, Normal Range • VCC = 2.7V to 3.6V, Extended Range μ W typ. static) • CMOS power levels (0.4μ • All inputs, outputs, and I/O are 5V tolerant • Supports hot insertion • Available in TSSOP package DRIVE FEATURES: • Balanced Output Drivers: ±12mA • Low switching noise APPLICATIONS: • 5V and 3.3V mixed voltage systems • Data communication and telecommunication systems FUNCTIONAL BLOCK DIAGRAM 1DIR 24 1 2DIR 25 48 1OE 1A1 2OE 47 2A1 2 36 13 1B1 1A2 2A2 3 14 1B2 1A3 2A3 16 1B3 2B3 32 43 2A4 6 17 1B4 1A5 2B4 41 2A5 30 8 19 1B5 1A6 40 2A6 9 1A7 20 1B6 38 2A7 22 2B7 37 2A8 INDUSTRIAL TEMPERATURE RANGE 2B6 27 1B7 12 2B5 29 11 1A8 2B2 33 44 5 1A4 2B1 35 46 26 23 1B8 2B8 1 OCTOBER 2015 DSC-4598/6 IDT74LVCHR162245A 3.3V CMOS 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION Symbol 1DIR 1 48 1OE 1B1 2 47 1A1 1B2 3 46 1A2 GND 4 45 GND 1B3 5 44 1A3 43 1A4 1B4 6 Description Max Unit VTERM Terminal Voltage with Respect to GND –0.5 to +6.5 V TSTG Storage Temperature –65 to +150 °C IOUT DC Output Current –50 to +50 mA IIK IOK Continuous Clamp Current, VI < 0 or VO < 0 –50 mA ICC ISS Continuous Current through each VCC or GND ±100 mA NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. VCC 7 42 VCC 1B5 8 41 1A5 1B6 9 40 1A6 GND 10 39 GND 1B7 11 38 1A7 Symbol Conditions Typ. Max. 1B8 12 37 1A8 CIN Input Capacitance VIN = 0V 4.5 6 pF COUT Output Capacitance VOUT = 0V 6.5 8 pF CI/O I/O Port Capacitance VIN = 0V 6.5 8 pF 2B1 13 36 2B2 14 35 2A2 GND 15 34 GND 2B3 16 33 2A3 2B4 17 32 2A4 VCC 18 31 VCC CAPACITANCE (TA = +25°C, F = 1.0MHz) 2A1 Parameter(1) Unit NOTE: 1. As applicable to the device type. PIN DESCRIPTION Pin Names Description xOE Output Enable Input (Active LOW) xDIR Direction Control Output 2B5 19 30 2A5 xAx Side A Inputs or 3-State Outputs(1) 2B6 20 29 2A6 xBx Side B Inputs or 3-State Outputs(1) GND 21 28 GND 2B7 22 27 2A7 2B8 23 26 2A8 2DIR 24 25 2OE NOTE: 1. These pins have "Bus-Hold". All other pins are standard inputs, outputs, or I/Os. FUNCTION TABLE (EACH 8-BIT SECTION)(1) Inputs TSSOP TOP VIEW xOE xDIR L L B Data to A Bus L H A Data to B Bus H X High Z State NOTE: 1. H = HIGH Voltage Level X = Don’t Care L = LOW Voltage Level Z = High-Impedance 2 Outputs IDT74LVCHR162245A 3.3V CMOS 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Operating Condition: TA = –40°C to +85°C Symbol VIH VIL Min. Typ.(1) Max. Unit VCC = 2.3V to 2.7V 1.7 — — V VCC = 2.7V to 3.6V 2 — — VCC = 2.3V to 2.7V — — 0.7 VCC = 2.7V to 3.6V — — 0.8 Parameter Input HIGH Voltage Level Input LOW Voltage Level Test Conditions V Input Leakage Current VCC = 3.6V VI = 0 to 5.5V — — ±5 μA IOZH High Impedance Output Current VCC = 3.6V VO = 0 to 5.5V — — ±10 μA IOZL (3-State Output pins) IOFF Input/Output Power Off Leakage VCC = 0V, VIN or VO ≤ 5.5V — — ±50 μA VIK Clamp Diode Voltage VCC = 2.3V, IIN = –18mA — –0.7 –1.2 V VH ICCL ICCH ICCZ ΔICC Input Hysteresis Quiescent Power Supply Current VCC = 3.3V VCC = 3.6V VIN = GND or VCC — — 100 — — 10 mV μA 3.6 ≤ VIN ≤ 5.5V(2) One input at VCC - 0.6V, other inputs at VCC or GND — — — — 10 500 μA Min. Typ.(2) Max. Unit – 75 — — μA IIH IIL Quiescent Power Supply Current Variation NOTES: 1. Typical values are at VCC = 3.3V, +25°C ambient. 2. This applies in the disabled state only. BUS-HOLD CHARACTERISTICS Symbol IBHH Parameter(1) Test Conditions Bus-Hold Input Sustain Current VCC = 3V VI = 2V VI = 0.8V 75 — — Bus-Hold Input Sustain Current VCC = 2.3V VI = 1.7V — — — VI = 0.7V — — — VI = 0 to 3.6V — — ±500 IBHL IBHH IBHL IBHHO Bus-Hold Input Overdrive Current VCC = 3.6V IBHLO NOTES: 1. Pins with Bus-Hold are identified in the pin description. 2. Typical values are at VCC = 3.3V, +25°C ambient. 3 μA μA IDT74LVCHR162245A 3.3V CMOS 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE OUTPUT DRIVE CHARACTERISTICS Symbol VOH Test Conditions(1) Parameter Output HIGH Voltage Output LOW Voltage Max. Unit V VCC = 2.3V to 3.6V IOH = – 0.1mA VCC – 0.2 — VCC = 2.3V IOH = – 4mA 1.9 — IOH = – 6mA 1.7 — VCC = 2.7V IOH = – 4mA 2.2 — IOH = – 8mA 2 — IOH = – 6mA 2.4 — IOH = – 12mA 2 — VCC = 2.3V to 3.6V IOL = 0.1mA — 0.2 VCC = 2.3V IOL = 4mA — 0.4 IOL = 6mA — 0.55 IOL = 4mA — 0.4 IOL = 8mA — 0.6 IOL = 6mA — 0.55 IOL = 12mA — 0.8 VCC = 3V VOL Min. VCC = 2.7V VCC = 3V V NOTE: 1. VIH and VIL must be within the min. or max. range shown in the DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE table for the appropriate VCC range. TA = – 40°C to + 85°C. OPERATING CHARACTERISTICS, VCC = 3.3V ± 0.3V, TA = 25°C Symbol Parameter CPD Power Dissipation Capacitance per Transceiver Outputs enabled CPD Power Dissipation Capacitance per Transceiver Outputs disabled Test Conditions Typical Unit CL = 0pF, f = 10Mhz 39 pF 4 SWITCHING CHARACTERISTICS(1) Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ tSK(o) Parameter Propagation Delay xAx to xBx or xBx to xAx Output Enable Time xOE to xAx or xBx Output Disable Time xOE to xAx or xBx Output Skew(2) Min. — NOTES: 1. See TEST CIRCUITS AND WAVEFORMS. TA = – 40°C to + 85°C. 2. Skew between any two outputs of the same package and switching in the same direction. 4 VCC = 2.7V Max. 5.7 VCC = 3.3V ± 0.3V Min. Max. 1.5 4.8 Unit ns — 7.9 1.5 6.3 ns — 8.3 2.2 7.4 ns — — — 500 ps IDT74LVCHR162245A 3.3V CMOS 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS TEST CONDITIONS Symbol VCC(1)= 3.3V±0.3V VCC(1)= 2.7V VLOAD 6 VCC(2)= 2.5V±0.2V Unit 2 x Vcc V 6 VIH 2.7 2.7 Vcc V VT 1.5 1.5 Vcc / 2 V VLZ 300 300 150 mV VHZ 300 300 150 mV CL 50 50 30 pF VIH VT 0V VOH VT VOL SAME PHASE INPUT TRANSITION tPLH tPHL tPLH tPHL OUTPUT VIH VT 0V OPPOSITE PHASE INPUT TRANSITION LVC Link Propagation Delay Pulse (1, 2) Generator tPZL GND 500 VOUT OUTPUT SWITCH NORMALLY CLOSED LOW tPZH OUTPUT SWITCH NORMALLY OPEN HIGH D.U.T. 500 RT CL Test Circuit for All Outputs VIH VT 0V CONTROL INPUT Open VIN DISABLE ENABLE VLOAD VCC tPLZ VLOAD/2 VT VLOAD/2 VLZ VOL tPHZ VOH VHZ 0V VT 0V LVC Link LVC Link DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. Enable and Disable Times NOTE: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. NOTES: 1. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2.5ns; tR ≤ 2.5ns. 2. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2ns; tR ≤ 2ns. DATA INPUT SWITCH POSITION Switch Open Drain Disable Low Enable Low VLOAD ASYNCHRONOUS CONTROL Disable High Enable High GND SYNCHRONOUS CONTROL All Other Tests Open OUTPUT 1 tPLH1 tSK (x) tSK (x) tPLH2 tH Set-up, Hold, and Release Times VOH VT VOL VT tW HIGH-LOW-HIGH PULSE VT LVC Link tPHL2 Pulse Width tSK(x) = tPLH2 - tPLH1 or tPHL2 - tPHL1 Output Skew - tSK(X) tSU LOW-HIGH-LOW PULSE VOH VT VOL OUTPUT 2 tREM LVC Link VIH VT 0V tPHL1 tH TIMING INPUT Test INPUT tSU VIH VT 0V VIH VT 0V VIH VT 0V VIH VT 0V LVC Link NOTES: 1. For tSK(o) OUTPUT1 and OUTPUT2 are any two outputs. 2. For tSK(b) OUTPUT1 and OUTPUT2 are in the same bank. 5 IDT74LVCHR162245A 3.3V CMOS 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION X LVC XX Bus-Hold Temp. Range XX Family XX XXXX Device Type Package X Blank 8 Tube or Tray Tape and Reel PAG Thin Shrink Small Outline Package - Green 245A 16-Bit Bus Transceiver with 3-State Outputs R162 Double-Density with Resistors, ±12mA H Bus-hold 74 -40°C to +85°C DATASHEET DOCUMENT HISTORY 10/06/2015 Pg. 6 Updated the ordering information by removing non RoHS part and adding Tape and Reel information. 6 IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.