932S421BFLFT

DATASHEET PCIe Gen2 and QPI Clock for Intel-Based Servers ICS932S421B Key Specifications: • PCIe Gen 2 compliant SRC outputs • QPI & FBD 2 compliant CPU clocks • CPU cycle-cycle jitter: < 50ps • SRC cycle-cycle jitter: < 125ps • PCI cycle-cycle jitter: < 500ps • CPU output skew: < 50ps • SRC output skew: < 250ps • ± 100ppm frequency accuracy on all outputs Recommended Application: PCIe Gen 2 & QPI compliant CK410B+ clock for Intel-based servers Output Features: • 4 - 0.7V current-mode differential CPU pairs • 5 - 0.7V current-mode differential SRC pair • 4 - PCI (33MHz) • 3 - PCICLK_F, (33MHz) free-running • 1 - 48MHz • 2 - REF, 14.318MHz Functionality 1 Features/Benefits: • Supports spread spectrum modulation, 0 to -0.5% down spread • Uses external 14.318MHz crystal and external load capacitors for low ppm synthesis error • • CPU clocks independent of SRC/PCI clocks D2/D3 SMBus address 1 FS_C 0 0 0 0 1 1 1 1 2 FS_B FS_A 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 CPU MHz 266.67 133.33 200.00 166.67 333.33 100.00 400.00 SRC MHz PCI MHz REF MHz USB MHz 100.00 33.33 14.32 48.00 Reserved 1. FS_B and FS_C are three-level inputs. Please see VIL_FS and VIH_FS specifications in the Input/Supply/Common Output Parameters Table for correct values. Also refer to the Test Clarification Table. 2. FS_A is a low-threshold input. Please see the VIL_FS and VIH_FS specifications in the Input/Supply/Common Output Parameters Table for correct values. VDDPCI GNDPCI PCICLK0 PCICLK1 PCICLK2 PCICLK3 GNDPCI VDDPCI PCICLK_F0 PCICLK_F1 PCICLK_F2 VDD48 48MHz GND48 VDDSRC SRCCLKT0 SRCCLKC0 SRCCLKC1 SRCCLKT1 GNDSRC SRCCLKT2 SRCCLKC2 SRCCLKC3 SRCCLKT3 VDDSRC SRCCLKT4 SRCCLKC4 VDDSRC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 ICS932S421 Pin Configuration 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 FS_C/TEST_SEL REF0 REF1 VDDREF X1 X2 GNDREF FS_B/TEST_MODE FS_A VDDCPU CPUCLKT0 CPUCLKC0 VDDCPU CPUCLKT1 CPUCLKC1 GNDCPU CPUCLKT2 CPUCLKC2 VDDCPU CPUCLKT3 CPUCLKC3 VDDA GNDA IREF NC Vtt_PwrGd#/PD SDATA SCLK 56-pin SSOP & TSSOP IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 1 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers Pin Description Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 PIN NAME VDDPCI GNDPCI PCICLK0 PCICLK1 PCICLK2 PCICLK3 GNDPCI VDDPCI PCICLK_F0 PCICLK_F1 PCICLK_F2 VDD48 48MHz GND48 VDDSRC SRCCLKT0 SRCCLKC0 SRCCLKC1 SRCCLKT1 GNDSRC SRCCLKT2 SRCCLKC2 SRCCLKC3 SRCCLKT3 VDDSRC SRCCLKT4 SRCCLKC4 VDDSRC PIN TYPE PWR PWR OUT OUT OUT OUT PWR PWR OUT OUT OUT PWR OUT PWR PWR OUT OUT OUT OUT PWR OUT OUT OUT OUT PWR OUT OUT PWR DESCRIPTION Power supply for PCI clocks, nominal 3.3V Ground pin for the PCI outputs PCI clock output. PCI clock output. PCI clock output. PCI clock output. Ground pin for the PCI outputs Power supply for PCI clocks, nominal 3.3V Free running PCI clock not affected by PCI_STOP# . Free running PCI clock not affected by PCI_STOP# . Free running PCI clock not affected by PCI_STOP# . Power pin for the 48MHz output.3.3V 48MHz clock output. Ground pin for the 48MHz outputs Supply for SRC clocks, 3.3V nominal True clock of differential SRC clock pair. Complement clock of differential SRC clock pair. Complement clock of differential push-pull SRC clock pair. True clock of differential SRC clock pair. Ground pin for the SRC outputs True clock of differential SRC clock pair. Complement clock of differential SRC clock pair. Complement clock of differential SRC clock pair. True clock of differential SRC clock pair. Supply for SRC clocks, 3.3V nominal True clock of differential SRC clock pair. Complement clock of differential SRC clock pair. Supply for SRC clocks, 3.3V nominal IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 2 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers Pin Description (continued) Pin # 29 30 PIN NAME SCLK SDATA Type IN I/O 31 Vtt_PwrGd#/PD IN 32 NC N/A 33 IREF OUT 34 35 GNDA VDDA PWR PWR 36 CPUCLKC3 OUT 37 CPUCLKT3 OUT 38 VDDCPU PWR 39 CPUCLKC2 OUT 40 CPUCLKT2 OUT 41 GNDCPU PWR 42 CPUCLKC1 OUT 43 CPUCLKT1 OUT 44 VDDCPU PWR 45 CPUCLKC0 OUT 46 CPUCLKT0 OUT 47 VDDCPU PWR 48 FS_A IN 49 FS_B/TEST_MODE IN 50 51 52 53 54 55 GNDREF X2 X1 VDDREF REF1 REF0 56 FS_C/TEST_SEL PWR OUT IN PWR OUT OUT IN Pin Description Clock pin of SMBus circuitry, 5V tolerant. Data pin for SMBus circuitry, 3.3V tolerant. Vtt_PwrGd# is an active low input used to determine when latched inputs are ready to be sampled. PD is an asynchronous active high input pin used to put the device into a low power state. The internal clocks, PLLs and the crystal oscillator are stopped. No Connection. This pin establishes the reference current for the differential current-mode output pairs. This pin requires a fixed precision resistor tied to ground in order to establish the appropriate current. 475 ohms is the standard value. Ground pin for the PLL core. 3.3V power for the PLL core. Complementary clock of differential pair CPU outputs. These are current mode outputs. External resistors are required for voltage bias. True clock of differential pair CPU outputs. These are current mode outputs. External resistors are required for voltage bias. Supply for CPU clocks, 3.3V nominal Complementary clock of differential pair CPU outputs. These are current mode outputs. External resistors are required for voltage bias. True clock of differential pair CPU outputs. These are current mode outputs. External resistors are required for voltage bias. Ground pin for the CPU outputs Complementary clock of differential pair CPU outputs. These are current mode outputs. External resistors are required for voltage bias. True clock of differential pair CPU outputs. These are current mode outputs. External resistors are required for voltage bias. Supply for CPU clocks, 3.3V nominal Complementary clock of differential pair CPU outputs. These are current mode outputs. External resistors are required for voltage bias. True clock of differential pair CPU outputs. These are current mode outputs. External resistors are required for voltage bias. Supply for CPU clocks, 3.3V nominal 3.3V tolerant input for CPU frequency selection. Refer to input electrical characteristics for Vil_FS and Vih_FS values. 3.3V tolerant input for CPU frequency selection. Refer to input electrical characteristics for Vil_FS and Vih_FS values. TEST_MODE is a real time input to select between Hi-Z and REF/N divider mode while in test mode. Refer to Test Clarification Table. Ground pin for the REF outputs. Crystal output, Nominally 14.318MHz Crystal input, Nominally 14.318MHz. Ref, XTAL power supply, nominal 3.3V 14.318 MHz reference clock. 14.318 MHz reference clock. 3.3V tolerant input for CPU frequency selection. Low voltage threshold inputs, see input electrical characteristics for Vil_FS and Vih_FS values. TEST_Sel: 3-level latched input to enable test mode. Refer to Test Clarification Table IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 3 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers General Description ICS932S421B is a main clock synthesizer for CK410B-generation Intel server platforms. ICS932S421B is driven with a 14.318MHz crystal. It generates CPU outputs up to 400MHz and PCI-Express clocks at 100. The 48 MHz USB clock is an exact 48.000 MHz clock. The ICS932S421B generates all other clocks with less the +/- 100 ppm error. Block Diagram REF(1:0) X1 X2 XTAL OSC. 48MHz FIXED PLL DIVIDER CPU PLL DIVIDERS SRC/PCI PLL DIVIDERS CPUCLK(3:0) SRCCLK(4:0) PCICLK(3:0), PCICLK_F(2:0) FS(C:A) TEST_SEL CONTROL LOGIC VTT_PWRGD#/PD SDATA SCLK IREF Power Groups Pin Number VDD GND 53 50 1,8 2,7 15,25,28 20 35 34 12 14 47,44,38 41 Description Xtal, Ref PCICLK outputs SRCCLK outputs Master clock, CPU Analog 48MHz, PLL_48 CPUCLK clocks IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 4 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers Single-ended Output Terminations ICS932S421B Zo Rs CL=5pF Test Load SEPP Output Buffer (Single Ended Push Pull) Zo Rs CL=5pF Zo Rs CL=5pF SEPP Output Buffer (Single Ended Push Pull) The singled-ended outputs of the ICS 932S421B default to a drive strength of 2 loads. The REF clocks can be turned down to 1-load strength via the SMBus. Suggested termination resistors are as follows for transmission lines with Zo = 50 ohms: Single-ended outputs at 2-load strength (Power up default for all single-ended outputs) Driving 1 load, Rs = 33 ohms Driving 2 loads, Rs = 7.5 ohms Single-ended outputs at 1-load strength (REF clock only) Driving 1 load, Rs = 22 ohms IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 5 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers Absolute Maximum Rating PARAMETER SYMBOL 3.3V Core Supply Voltage VDD_A 3.3V Logic Input Supply VDD_In Voltage Storage Temperature Ts Ambient Operating Temp Tambient Case Temperature Tcase Input ESD protection HBM ESD prot CONDITIONS - MIN - TYP MAX VDD + 0.5V UNITS V Notes 1 GND - 0.5 VDD + 0.5V V 1 -65 0 150 70 115 ° C °C °C V 1 1 1 1 MAX VDD + 0.3 0.8 5 UNITS V V uA Notes 1 1 1 -5 uA 1 -200 uA 1 2000 1 Guaranteed by design and characterization, not 100% tested in production. Electrical Characteristics - Input/Supply/Common Output Parameters PARAMETER Input High Voltage Input Low Voltage Input High Current SYMBOL VIH VIL I IH CONDITIONS* 3.3 V +/-5% 3.3 V +/-5% V IN = VDD VIN = 0 V; Inputs with no pull-up resistors VIN = 0 V; Inputs with pull-up resistors MIN 2 VSS - 0.3 -5 VIH_FS 3.3 V +/-5% 0.7 VDD + 0.3 V 1 VSS - 0.3 0.35 V 1 350 70 12 7 5 6 5 mA mA mA MHz nH pF pF pF 1 1 1 2 1 1 1 1 1.8 ms 1 33 kHz 1 300 us 1 5 5 5.5 0.4 ns ns V V 1 1 1 1 mA 1 1000 ns 1 300 ns 1 IIL1 Input Low Current IIL2 Low Threshold InputHigh Voltage Low Threshold InputLow Voltage Operating Supply Current VIL_FS 3.3 V +/-5% IDD3.3OP Powerdown Current I DD3.3PD Input Frequency Pin Inductance Fi Lpin CIN COUT CINX Full Active, CL = Full load; all diff pairs driven all differential pairs tri-stated VDD = 3.3 V Input Capacitance Clk Stabilization TSTAB Modulation Frequency Tdrive_PD Tfall_PD Trise_PD SMBus Voltage Low-level Output Voltage Current sinking at VOL = 0.4 V SCLK/SDATA Clock/Data Rise Time SCLK/SDATA Clock/Data Fall Time Logic Inputs Output pin capacitance X1 & X2 pins From VDD Power-Up or deassertion of PD to 1st clock Triangular Modulation CPU output enable after PD de-assertion PD fall time of PD rise time of TFI2C 30 @ IPULLUP IPULLUP TRI2C 14.31818 2.7 VDD VOL TYP 4 (Max VIL - 0.15) to (Min VIH + 0.15) (Min VIH + 0.15) to (Max VIL - 0.15) *TA = 0 - 70°C; Supply Voltage VDD = 3.3 V +/-5% 1 2 Guaranteed by design and characterization, not 100% tested in production. Input frequency should be measured at the REF pin and tuned to ideal 14.31818MHz to meet ppm frequency accuracy on PLL outputs. IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 6 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers Electrical Characteristics - CPU 0.7V Current Mode Differential Pair PARAMETER Current Source Output Impedance Voltage High Voltage Low Max Voltage Min Voltage Crossing Voltage (abs) SYMBOL CONDITIONS* MIN Zo VO = Vx 3000 VHigh VLow Vovs Vuds Vx(abs) Statistical measurement on single ended signal Measurement on single ended signal using absolute value. 660 -150 Crossing Voltage (var) d-Vx Rise Time Fall Time Rise Time Variation Fall Time Variation tr tf d-tr d-tf Duty Cycle dt3 Skew tsk3 Jitter, Cycle to cycle tjcyc-cyc TYP UNITS NOTES Ω 1 550 mV mV mV mV mV 1,3 1,3 1 1 1 140 mV 1 175 175 525 525 125 125 ps ps ps ps 1 1 1 1 45 55 % 1 50 ps 1 50 ps 1 850 150 1150 -300 250 Variation of crossing over all edges VOL = 0.175V, VOH = 0.525V VOL = 0.175V, VOH = 0.525V VOL = 0.175V, VOH = 0.525V VOL = 0.175V, VOH = 0.525V Measurement from differential waveform across all CPU outputs, VT = 50% Measurement from differential waveform MAX *TA = 0 - 70°C; VDD = 3.3 V +/-5%; CL =2pF, RS=33.2Ω, RP=49.9Ω, ΙREF = 475Ω 1 Guaranteed by design and characterization, not 100% tested in production. 2 All Long Term Accuracy and Clock Period specifications are guaranteed assuming that REF is at 14.31818MHz 3 IREF = VDD/(3xRR). For RR = 475Ω (1%), IREF = 2.32mA. IOH = 6 x IREF and VOH = 0.7V @ ZO=50Ω. Electrical Characteristics - SRC 0.7V Current Mode Differential Pair PARAMETER Current Source Output Impedance Voltage High Voltage Low Max Voltage Min Voltage Crossing Voltage (abs) SYMBOL CONDITIONS* MIN Zo VO = Vx 3000 VHigh VLow Vovs Vuds Vx(abs) Statistical measurement on single ended signal Measurement on single ended signal using absolute value. 660 -150 Crossing Voltage (var) d-Vx Rise Time Fall Time Rise Time Variation Fall Time Variation tr tf d-tr d-tf Duty Cycle dt3 Skew tsk3 Jitter, Cycle to cycle tjcyc-cyc Variation of crossing over all edges VOL = 0.175V, VOH = 0.525V VOH = 0.525V VOL = 0.175V VOL = 0.175V, VOH = 0.525V VOH = 0.525V VOL = 0.175V Measurement from differential waveform VT = 50% Measurement from differential waveform -300 250 TYP MAX UNITS Notes Ω 1 550 mV mV mV mV mV 1,3 1,3 1 1 1 850 150 1150 140 mV 1 175 175 525 525 125 125 ps ps ps ps 1 1 1 1 45 55 % 1 250 ps 1 125 ps 1 *TA = 0 - 70°C; VDD = 3.3 V +/-5%; CL =2pF, RS=33.2Ω, RP=49.9Ω, ΙREF = 475Ω 1 Guaranteed by design and characterization, not 100% tested in production. 2 All Long Term Accuracy and Clock Period specifications are guaranteed assuming that REF is at 14.31818MHz 3 IREF = VDD/(3xRR). For RR = 475Ω (1%), IREF = 2.32mA. IOH = 6 x IREF and VOH = 0.7V @ ZO=50Ω. IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 7 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers Electrical Characteristics - PCICLK/PCICLK_F PARAMETER Long Accuracy Clock period SYMBOL ppm Tperiod CONDITIONS* see Tperiod min-max values 33.33MHz output nominal MIN -100 29.9970 Absolute Clock period Tpabs 33.33MHz output including jitter 29.4970 Clock period w/spread Absolute Clock period w/spread Clock High Time Clock Low Time Output Impedance Output High Voltage Output Low Voltage TperiodSS 33.33MHz output nominal 30.0722 TpabsSS 33.33MHz output including jitter THIGH TLOW RDSP VOH VOL 1.5V 1.5V VO = VDD*(0.5) IOH = -1 mA IOL = 1 mA V OH @MIN = 1.0 V VOH@MAX = 3.135 V VOL @ MIN = 1.95 V VOL @ MAX = 0.4 V Rising/Falling edge rate VOL = 0.4 V, VOH = 2.4 V VOH = 2.4 V, VOL = 0.4 V VT = 1.5 V VT = 1.5 V VT = 1.5 V Output High Current IOH Output Low Current IOL Edge Rate Rise Time Fall Time Duty Cycle Group Skew Jitter, Cycle to cycle tslewr/f tr tf dt1 tskew tjcyc-cyc TYP 30 MAX 100 30.0030 UNITS NOTES ppm 1,2 ns 2 30.5030 ns 2 30.0852 ns 2, 3 29.5722 30.5852 ns 2,3 12 12 12 2.4 N/A N/A 55 ns 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 30.07519 0.55 -33 -33 30 1 0.5 0.5 45 38 4 2 2 55 250 500 ns 8 V V mA mA mA mA V/ns ns ns % ps ps *TA = 0 - 70°C; Supply Voltage VDD = 3.3 V +/-5% (unless otherwise specified) 1 Guaranteed by design and characterization, not 100% tested in production. 2 All Long Term Accuracy and Clock Period specifications are guaranteed assuming that REF is at 14.31818MHz 3 Does not apply to 932S431A IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 8 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers Electrical Characteristics - USB48MHz PARAMETER Long Accuracy Clock period SYMBOL ppm Tperiod CONDITIONS* see Tperiod min-max values 48.00MHz output nominal MIN 0 20.8333 Absolute Clock period Tpabs 48.00MHz output including jitter 20.4833 21.1833 Output Impedance Output High Voltage Clock High Time Clock Low Time Output Low Voltage RDSP VOH THIGH TLOW VOL 12 2.4 8.094 7.694 55 Output High Current IOH VO = VDD*(0.5) IOH = -1 mA 1.5V 1.5V IOL = 1 mA V OH @MIN = 1.0 V VOH@MAX = 3.135 V V OL @ MIN = 1.95 V V OL @ MAX = 0.4 V Output Low Current Edge Rate Rise Time Fall Time Duty Cycle Group Skew Jitter, Cycle to cycle IOL tjcyc-cyc 20.83333 MAX 0 20.8333 ns 2 27 ns V mA mA mA mA 1 2 V/ns 1 1 1 45 2 2 55 250 350 ns ns % ps ps 1 1 1 1 1 10.036 9.836 0.55 -33 29 VOL = 0.4 V, VOH = 2.4 V VOH = 2.4 V, V OL = 0.4 V VT = 1.5 V VT = 1.5 V VT = 1.5 V UNITS NOTES ppm 1,2 ns 2 1 1 1 1 1 1 1 1 1 -29 tslewr/f_USB USB48 Rising/Falling edge rate tr_USB tf_USB dt1 tskew TYP V ns *TA = 0 - 70°C; Supply Voltage VDD = 3.3 V +/-5% 1 2 Guaranteed by design and characterization, not 100% tested in production. All Long Term Accuracy and Clock Period specifications are guaranteed assuming that REF is at 14.31818MHz IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 9 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers Electrical Characteristics - REF PARAMETER Long Accuracy Clock period SYMBOL ppm Tperiod Absolute Clock period Tpabs Clock High Time Clock Low Time Output High Voltage Output Low Voltage THIGH TLOW VOH VOL Output High Current CONDITIONS see Tperiod min-max values 14.318MHz output nominal 14.318MHz output including jitter 1.5V 1.5V IOH = -1 mA IOL = 1 mA V OH @MIN = 1.0 V VOH@MAX = 3.135 V V OL @ MIN = 1.95 V V OL @ MAX = 0.4 V Rising/Falling edge rate VOL = 0.4 V, VOH = 2.4 V VOH = 2.4 V, V OL = 0.4 V VT = 1.5 V VT = 1.5 V VT = 1.5 V IOH Output Low Current IOL Edge Rate Rise Time Fall Time Skew Duty Cycle Jitter t slewr/f t r1 t f1 tsk1 dt1 tjcyc-cyc MIN -100 69.8343 TYP 0 69.84128 MAX 100 69.8483 UNITS ppm ns Notes 1,2 2 68.8343 70.8483 ns 2 27.533718 27.533718 2.4 N/A N/A ns 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0.4 -33 -33 30 38 4 2 2 500 55 1000 1 0.5 0.5 45 ns V V mA mA mA mA V/ns ns ns ps % ps *TA = 0 - 70°C; Supply Voltage VDD = 3.3 V +/-5% 1 2 Guaranteed by design and characterization, not 100% tested in production. All Long Term Accuracy and Clock Period specifications are guaranteed assuming that REF is at 14.31818MHz Electrical Characteristics - Differential Jitter Parameters PARAMETER Symbol tjphasePLL t jphaseLo tjphaseHigh Jitter, Phase tjphFBD1_3.2 G Conditions PCIe Gen 1 PCIe Gen 2 10kHz < f < 1.5MHz PCIe Gen 2 1.5MHz < f < Nyquist (50MHz) FBD1 3.2/4G 11MHz to 33MHz tjphFBD1_4.0 G tjphQPI FBD1 4.8G 11MHz to 33MHz QPI 133MHz 6.4GB_12UI CPU outputs only Min TYP 40 Max 86 1.7 3 2.2 3.1 2.5 3 2 2.5 0.25 0.5 Units ps (p-p) ps (RMS) ps (RMS) ps (RMS) ps (RMS) ps (RMS) Notes 1,2 1,2 1,2 1,2 1,2 1,2 *TA = 0 - 70°C; Supply Voltage VDD = 3.3 V +/-5% 1 2 Guaranteed by design and characterization, not 100% tested in production. See http://www.pcisig.com for complete specs IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 10 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers Differential Clock AC Tolerances PPM tolerance Cycle to Cycle Jitter Spread CPU 100 50 -0.50% SRC 100 125 -0.50% DOT96 100 250 0 BMC133 100 125 -0.50% ppm ps % Clock Periods - Differential Outputs with Spread Spectrum Disabled SSC ON CPU SRC Center Freq. MHz 100.00 133.33 166.67 200.00 266.67 333.33 400.00 100.00 Measurement Window 1us 0.1s 0.1s 0.1s + ppm -SSC - ppm 0 ppm -c2c jitter Long-Term Short-Term Long-Term Period AbsPer Average Average Average Nominal Min Max Min Min 9.94900 9.99900 10.00000 10.00100 7.44925 7.49925 7.50000 7.50075 5.94940 5.99940 6.00000 6.00060 4.94950 4.99950 5.00000 5.00050 3.69962 3.74962 3.75000 3.75037 2.94970 2.99970 3.00000 3.00030 2.44975 2.49975 2.50000 2.50025 9.87400 9.99900 10.00000 10.00100 1 Clock 1us +SSC Short-Term Average Max 1 Clock +c2c jitter Units Notes AbsPer Max 10.05100 7.55075 6.05060 5.05050 3.80037 3.05030 2.55025 10.12600 ns ns ns ns ns ns ns ns 1,2 1,2 1,2 1,2 1,2 1,2 1,2 1,2 Clock Periods - Differential Outputs with Spread Spectrum Enabled SSC ON CPU SRC 1 2 Center Freq. MHz 99.75 133.00 166.25 199.50 266.00 332.50 399.00 99.75 Measurement Window 1us 0.1s 0.1s 0.1s + ppm - ppm -SSC 0 ppm -c2c jitter Long-Term Short-Term Long-Term Period AbsPer Average Average Average Nominal Min Max Min Min 9.94906 9.99906 10.02406 10.02506 10.02607 7.44930 7.49930 7.51805 7.51880 7.51955 5.94944 5.99944 6.01444 6.01504 6.01564 4.94953 4.99953 5.01203 5.01253 5.01303 3.69965 3.74965 3.75902 3.75940 3.75977 2.94972 2.99972 3.00722 3.00752 3.00782 2.44977 2.49977 2.50602 2.50627 2.50652 9.87406 9.99906 10.02406 10.02506 10.02607 1 Clock 1us +SSC Short-Term Average Max 10.05107 7.53830 6.03064 5.02553 3.76915 3.01532 2.51277 10.05107 1 Clock +c2c jitter Units Notes AbsPer Max 10.10107 7.58830 6.08064 5.07553 3.81915 3.06532 2.56277 10.17607 ns ns ns ns ns ns ns ns 1,2 1,2 1,2 1,2 1,2 1,2 1,2 1,2 Guaranteed by design and characterization, not 100% tested in production. All Long Term Accuracy specifications are guaranteed with the assumption that the crystal input is tuned to exactly 14.31818MHz. IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 11 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers General SMBus serial interface information for the ICS932S421B How to Write: How to Read: Controller (host) sends a start bit. Controller (host) sends the write address D2 (H) ICS clock will acknowledge Controller (host) sends the beginning byte location = N ICS clock will acknowledge Controller (host) sends the data byte count = X ICS clock will acknowledge Controller (host) starts sending Byte N through Byte N + X -1 (see Note 2) • ICS clock will acknowledge each byte one at a time • Controller (host) sends a Stop bit • • • • • • • • • • • • • • • • • • • • • • Controller (host) will send start bit. Controller (host) sends the write address D2 (H) ICS clock will acknowledge Controller (host) sends the begining byte location = N ICS clock will acknowledge Controller (host) will send a separate start bit. Controller (host) sends the read address D3 (H) ICS clock will acknowledge ICS clock will send the data byte count = X ICS clock sends Byte N + X -1 ICS clock sends Byte 0 through byte X (if X(H) was written to byte 8). Controller (host) will need to acknowledge each byte Controller (host) will send a not acknowledge bit Controller (host) will send a stop bit Index Block Read Operation Index Block Write Operation Controller (Host) starT bit T Slave Address D2(H) WR WRite Controller (Host) T starT bit Slave Address D2(H) WR WRite ICS (Slave/Receiver) ICS (Slave/Receiver) ACK ACK Beginning Byte = N Beginning Byte = N ACK ACK RT Repeat starT Slave Address D3(H) RD ReaD Data Byte Count = X ACK Beginning Byte N ACK X Byte ACK Data Byte Count = X ACK Beginning Byte N Byte N + X - 1 ACK X Byte ACK P stoP bit Byte N + X - 1 N P IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers Not acknowledge stoP bit 1340G—01/26/10 12 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers SMBus Table: Output Enable Register Byte 0 Bit 7 Pin # NA Name SRCCLK7 Enable Control Function Output Enable Type RW 0 Disable-Hi-Z 1 Enable PWD 1 Bit 6 NA SRCCLK6 Enable Output Enable RW Disable-Hi-Z Enable 1 Bit 5 NA SRCCLK5 Enable Output Enable RW Disable-Hi-Z Enable 1 Bit 4 26,27 SRCCLK4 Enable Output Enable RW Disable-Hi-Z Enable 1 Bit 3 23,24 SRCCLK3 Enable Output Enable RW Disable-Hi-Z Enable 1 Bit 2 21,22 SRCCLK2 Enable Output Enable RW Disable-Hi-Z Enable 1 Bit 1 18,19 SRCCLK1 Enable Output Enable RW Disable-Hi-Z Enable 1 Bit 0 16,17 SRCCLK0 Enable Output Enable RW Disable-Hi-Z Enable 1 Name REF1 Enable Control Function Output Enable Type RW 0 Disable-Low 1 Enable PWD 1 REF0 Enable Output Enable RW Disable-Low Enable 1 SMBus Table: Output Enable Register Byte 1 Bit 7 Pin # Bit 6 54 55 Bit 5 36,37 CPUCLK3 Output Enable RW Disable-Hi-Z Enable 1 Bit 4 39,40 CPUCLK2 Output Enable RW Disable-Hi-Z Enable 1 RESERVED Bit 3 0 Bit 1 42,43 45,46 CPUCLK1 CPUCLK0 Output Enable RW Disable-Hi-Z Enable 1 Bit 0 CPU, SRC, PCI Spread Spectrum Enable Spread Off/On RW Spread Off Spread On 0 Bit 2 Output Enable RW Disable-Hi-Z Enable 1 SMBus Table: Output Enable Register Byte 2 Bit 7 Pin # 6 Name PCICLK3 Control Function Output Enable Type RW 0 Disable-Low 1 Enable PWD 1 Bit 6 5 PCICLK2 Output Enable RW Disable-Low Enable 1 Bit 5 4 PCICLK1 Output Enable RW Disable-Low Enable 1 Bit 4 3 PCICLK0 Output Enable RW Disable-Low Enable 1 Bit 3 11 PCICLK_F2 Enable Output Enable RW Disable-Low Enable 1 Bit 2 10 PCICLK_F1 Enable Output Enable RW Disable-Low Enable 1 Bit 1 9 PCICLK_F0 Enable Output Enable RW Disable-Low Enable 1 13 48MHz Enable Output Enable RW Disable-Low Enable 1 Control Function Type RW 0 Free-Running 1 Stoppable PWD 1 Bit 0 SMBus Table: Stop Control Register Byte 3 Bit 7 Pin # 11 Name PCICLK_F2 Stop En Bit 6 10 PCICLK_F1 Stop En RW Free-Running Stoppable 1 Bit 5 9 PCICLK_F0 Stop En RW Free-Running Stoppable 1 Bit 4 26,27 SRCCLK4 Stop En RW Free-Running Stoppable 1 Bit 3 23,24 SRCCLK3 Stop En RW Free-Running Stoppable 1 Bit 2 21,22 SRCCLK2 Stop En RW Free-Running Stoppable 1 Bit 1 18,19 SRCCLK1 Stop En RW Free-Running Stoppable 1 Bit 0 16,17 SRCCLK0 Stop En RW Free-Running Stoppable 1 Free-Running Control, Default: not affected by PCI/SRC_STOP (Byte 6, bit 3) IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 13 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers SMBus Table: Stop and Power Down Mode Drive Control Register Byte 4 Bit 7 36,37 Name CPUCLK3 PD Drive Control Function Drive Mode in PD Type RW 0 Driven 1 Hi-Z PWD 0 Bit 6 39,40 CPUCLK2 PD Drive Drive Mode in PD RW Driven Hi-Z 0 Drive mode in PD RW Driven Hi-Z 0 Bit 4 42,43 45,46 CPUCLK1 PD Drive CPUCLK0 PD Drive Drive mode in PD RW Driven Hi-Z 0 Bit 3 36,37 CPUCLK3 Stop En RW Free-Running Stoppable 1 Bit 2 39,40 CPUCLK2 Stop En RW Free-Running Stoppable 1 Bit 1 42,43 45,46 CPUCLK1 Stop En RW Free-Running Stoppable 1 RW Free-Running Stoppable 1 Bit 5 Bit 0 Pin # Free-Running Control, Default: not affected by CPU_STOP CPUCLK0 Stop En SMBus Table: Stop and Power Down Mode Drive Control Register Byte 5 Pin # Name Control Function RESERVED Type 0 1 PWD 0 0 Bit 7 Bit 6 SRC SRC Stop Drive Mode Driven in STOP RW Driven Hi-Z Bit 5 SRC SRC PD Drive Mode Driven in PD RW Driven Hi-Z RESERVED Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 36,37 CPUCLK3 Stop Drive Drive Mode in Stop RW Driven Hi-Z 0 39,40 CPUCLK2 Stop Drive Drive Mode in Stop RW Driven Hi-Z 0 CPUCLK1 Stop Drive Drive Mode in Stop RW Driven Hi-Z 0 CPUCLK0 Stop Drive Drive Mode in Stop RW Driven Hi-Z 0 PWD 0 42,43 45,46 SMBus Table: Test Mode and FS Readback Register Byte 6 Bit 7 - Name Test Mode Selection Control Function Test Mode Selection Type RW 0 Hi-Z 1 REF/N Bit 6 - Test Clock Mode Entry Test Mode RW Disable Enable Bit 5 - Bit 4 54,55 REF Drive Strength Bit 3 PCI, SRC PCI_STOP Control Bit 2 - Bit 1 Bit 0 Pin # RESERVED 0 0 RW 1X 2X 1 RW Stop Run 1 FS_C 1X or 2X Stop non-free running PC and SRC clocks. FS_C readback FS_B FS_B readback R FS_A FS_A readback R Control Function R See 932S421 Functionality Table Latch Latch Latch SMBus Table: Vendor & Revision ID Register Byte 7 Type 0 1 PWD Bit 7 - Pin # Name RID3 R - - 0 Bit 6 - RID2 R - - 0 Bit 5 - RID1 R - - 0 Bit 4 - RID0 R - - 1 Bit 3 - VID3 R - - 0 Bit 2 - VID2 R - - 0 Bit 1 - VID1 R - - 0 Bit 0 - VID0 R - - 1 REVISION ID VENDOR ID IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 14 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers SMBus Table: Byte Count Register Byte 8 Bit 7 - Pin # Name BC7 Control Function Bit 6 - BC6 RW Bit 5 - BC5 RW Bit 4 - BC4 RW Bit 3 - BC3 Bit 2 - BC2 RW Bit 1 - BC1 RW 1 Bit 0 - BC0 RW 1 Byte Count Programming b(7:0) Type RW RW 0 1 PWD 0 0 Writing to this register will configure how many bytes will be read back, default is 8 bytes. (0 to 7) 0 0 0 1 SMBus Table: Device ID Register Byte 9 Pin # Bit 7 Name DID7 Control Function Bit 6 DID6 Bit 5 DID5 Bit 4 DID4 Bit 3 DID3 Bit 2 DID2 R - - 0 Bit 1 DID1 R - - 1 Bit 0 DID0 R - - 1 0 1 PWD Disable Enable 0 Stop Run 1 Device ID (2B hex) Type R 0 - 1 - PWD 0 R - - 0 R - - 1 R - - 0 R - - 1 SMBus Table: M/N Programming & Control Register Byte 10 Pin # Name Bit 7 - M/N_EN Bit 6 CPU CPU_STOP Control Bit 5 - Bit 4 - Bit 3 SRC, PCI SRC Alternate Frequency (96% of Nominal) Bit 2 CPU Bit 1 54 CPU Alternate Frequency (96% of Nominal) Only active if latched frequency is 166 MHz or 333 MHz. REF1 Drive Strength Bit 0 55 REF0 Drive Strength Control Function Type CPU and SRC M/N Programming RW Enable Stop non-free running PC RW and SRC clocks. RESERVED RESERVED Set SRC = 96 MHz and PCI = 32 MHz Only active if Byte 10, bit 2 = 1 Set alternate CPU frequency: 166 MHz to 160 MHz 333 MHz to 320 MHz 1X or 2X 1X or 2X RW IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 0 0 RW Normal Alternate Frequency 0 RW Normal Alternate Frequency 0 RW See REF Drive Strength Functionality Table 1 1 1340G—01/26/10 15 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers SMBus Table: CPU Frequency Control Register Byte 11 Pin # Name CPU N Div8 Control Function N Divider Prog bit 8 Type RW - CPU N Div9 N Divider Prog bit 9 RW Bit 5 - CPU M Div5 Bit 4 - CPU M Div4 Bit 3 - CPU M Div3 Bit 2 - CPU M Div2 Bit 1 - CPU M Div1 RW Bit 0 - CPU M Div0 RW Bit 7 - Bit 6 RW RW M Divider Programming bit (5:0) RW RW 0 1 The decimal representation of M and N Divider in Byte 11 and 12 will configure the CPU VCO frequency. Default at power up = latch-in or Byte 0 Rom table. VCO Frequency = 14.318 x [NDiv(9:0)+8] / [MDiv(5:0)+2] PWD X X X X X X X X SMBus Table: CPU Frequency Control Register Byte 12 Bit 7 - Pin # Name CPU N Div7 Control Function Bit 6 - CPU N Div6 RW Bit 5 - CPU N Div5 RW Bit 4 - CPU N Div4 Bit 3 - CPU N Div3 Bit 2 - CPU N Div2 RW Bit 1 - CPU N Div1 RW Bit 0 - CPU N Div0 RW N Divider Programming Byte12 bit(7:0) and Byte11 bit(7:6) Type RW RW RW 0 1 The decimal representation of M and N Divider in Byte 11 and 12 will configure the CPU VCO frequency. Default at power up = latch-in or Byte 0 Rom table. VCO Frequency = 14.318 x [NDiv(9:0)+8] / [MDiv(5:0)+2] PWD X X X X X X X X SMBus Table: CPU Spread Spectrum Control Register Byte 13 Pin # Name Control Function Type 0 1 PWD Bit 7 - CPU SSP7 RW X Bit 6 - CPU SSP6 RW X Bit 5 - CPU SSP5 RW Bit 4 - CPU SSP4 Bit 3 - CPU SSP3 Bit 2 - CPU SSP2 RW X Bit 1 - CPU SSP1 RW X Bit 0 - CPU SSP0 RW X Spread Spectrum Programming bit(7:0) RW RW X These Spread Spectrum bits in Byte 13 and 14 will program the spread pecentage of CPU X X SMBus Table: CPU Spread Spectrum Control Register Byte 14 Pin # Name Control Function Reserved Type 0 1 PWD 0 Bit 7 - Bit 6 - CPU SSP14 RW Bit 5 - CPU SSP13 RW Bit 4 - CPU SSP12 RW Bit 3 - CPU SSP11 Bit 2 - CPU SSP10 Bit 1 - CPU SSP9 RW X Bit 0 - CPU SSP8 RW X Spread Spectrum Programming bit(14:8) IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers RW RW X X These Spread Spectrum bits in Byte 13 and 14 will program the spread pecentage of CPU X X X 1340G—01/26/10 16 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers SMBus Table: SRC/PCI Frequency Control Register Byte 15 Pin # Name SRC N Div8 Control Function N Divider Prog bit 8 Type RW - SRC N Div9 N Divider Prog bit 9 RW Bit 5 - SRC M Div5 RW Bit 4 - SRC M Div4 RW Bit 3 - SRC M Div3 Bit 2 - SRC M Div2 Bit 1 - SRC M Div1 RW Bit 0 - SRC M Div0 RW Bit 7 - Bit 6 M Divider Programming bits RW RW 0 1 The decimal representation of M and N Divider in Byte 15 and 16 will configure the SRC VCO frequency. Default at power up = latch-in or Byte 0 Rom table. VCO Frequency = 14.318 x [NDiv(9:0)+8] / [MDiv(5:0)+2] PWD X X X X X X X X SMBus Table: SRC/PCI Frequency Control Register Byte 16 Bit 7 - Pin # Name SRC N Div7 Control Function Bit 6 - SRC N Div6 RW Bit 5 - SRC N Div5 RW Bit 4 - SRC N Div4 Bit 3 - SRC N Div3 Bit 2 - SRC N Div2 RW Bit 1 - SRC N Div1 RW Bit 0 - SRC N Div0 RW N Divider Programming b(7:0) Type RW RW RW 0 1 The decimal representation of M and N Divider in Byte 15 and 16 will configure the SRC VCO frequency. Default at power up = latch-in or Byte 0 Rom table. VCO Frequency = 14.318 x [NDiv(9:0)+8] / [MDiv(5:0)+2] PWD X X X X X X X X SMBus Table: SRC/PCI Spread Spectrum Control Register Byte 17 Bit 7 - Pin # Name SRC SSP7 Control Function Type RW 0 1 Bit 6 - SRC SSP6 Bit 5 - SRC SSP5 Bit 4 - SRC SSP4 Bit 3 - SRC SSP3 Bit 2 - SRC SSP2 RW X Bit 1 - SRC SSP1 RW X Bit 0 - SRC SSP0 RW X RW X RW Spread Spectrum Programming b(7:0) RW RW PWD X X These Spread Spectrum bits in Byte 17 and 18 will program the spread pecentage of SRC X X SMBus Table: SRC/PCI Spread Spectrum Control Register Byte 18 Bit 7 - Pin # Name Reserved Control Function Reserved Bit 6 - SRC SSP14 RW X Bit 5 - SRC SSP13 RW X Bit 4 - SRC SSP12 RW Bit 3 - SRC SSP11 Bit 2 - SRC SSP10 Bit 1 - SRC SSP9 RW X Bit 0 - SRC SSP8 RW X Spread Spectrum Programming b(14:8) IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers Type R RW RW 0 - 1 - These Spread Spectrum bits in Byte 17 and 18 will program the spread pecentage of SRC PWD 0 X X X 1340G—01/26/10 17 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers SMBus Table: CPU Programmable Output Divider Register Byte 19 Pin # Name Control Function Bit 7 - CPUDiv3 Bit 6 - CPUDiv2 Bit 5 - CPUDiv1 Bit 4 - CPUDiv0 Type 0 1 RW CPU Divider Ratio Programming Bits RW RW PWD X See CPU, SRC and PCI Divider Ratios Table RW X X X Bit 3 RESERVED X Bit 2 RESERVED X Bit 1 RESERVED X Bit 0 RESERVED X SMBus Table: SRC and PCI Programmable Output Divider Register Byte 20 Bit 7 Name PCIDiv3 Control Function - Pin # Type RW Bit 6 - PCIDiv2 RW Bit 5 - PCIDiv1 PCI Divider Ratio Programming Bits Bit 4 - PCIDiv0 RW X Bit 3 - SRC_Div3 RW X Bit 2 - SRC_Div2 Bit 1 - SRC_Div1 Bit 0 - SRC_Div0 SRC_ Divider Ratio Programming Bits RW RW RW 0 1 See CPU, SRC and PCI Divider Ratios Table See CPU, SRC and PCI Divider Ratios Table RW PWD X X X X X X SMBusTable: Test Byte Register Byte 21 Type RW Test Result ICS ONLY TEST Reserved PWD 0 Bit 6 ICS ONLY TEST RW Reserved 0 Bit 5 ICS ONLY TEST RW Reserved 0 Bit 4 ICS ONLY TEST RW Reserved 0 Bit 3 ICS ONLY TEST RW Reserved 0 Bit 2 ICS ONLY TEST RW Reserved 0 Bit 1 ICS ONLY TEST RW Reserved 0 Bit 0 ICS ONLY TEST RW Reserved 0 Bit 7 Test ` Test Function Note: Do NOT write to Byte 21. Erratic device operation will result! IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 18 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers PD, Power Down PD is an asynchronous active high input used to shut off all clocks cleanly prior to system power down. When PD is asserted, all clocks will be driven low before turning off the VCO. All clocks will start without glitches when PD is de-asserted. PD CPU CPU # SRC SRC# PCIF/PCI USB REF Note 0 Normal Normal Normal Normal 33MHz 48MHz 14.318MHz 1 1 Iref * 2 or Float Float Iref * 2 or Float Float Low Low Low 1 Notes: 1. Refer to SMBus Byte 4 for additional information. PD Assertion PD should be sampled high by 2 consecutive CPU# rising edges before stopping clocks. All single ended clocks will be held low on their next high to low transition. All differential clocks will be held high on the next high to low transition of the complimentary clock. If the control register determining to drive mode is set to 'tri-state', the differential pair will be stopped in tri-state mode, undriven. When the drive mode corresponding to the CPU or SRC clock of interest is set to '0' the true clock will be driven high at 2 x Iref and the complementary clock will be tristated. If the control register is programmed to '1' both clocks will be tristated. See SMBus Bytes 4 and 5 for additional information. PD CPU, 133MHz CPU#, 133MHz SRC, 100MHz SRC#, 100MHz USB, 48MHz PCI, 33MHz REF, 14.31818 CPU, SRC and PCI Divider Ratios Div(3:0) Divider 0 0000 2 1 0001 3 2 0010 5 3 0011 15 4 0100 4 5 0101 6 6 0110 10 7 0111 30 8 1000 8 9 1001 12 10 1010 20 11 1011 60 12 1100 16 13 1101 24 14 1110 40 15 1111 120 REF Drive Strength Functionality Byte6, Byte Byte 10, bit 4 10, bit 1 bit 0 0 X X 1 0 0 1 0 1 1 1 0 1 1 1 IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers REF1 1x 1x 1x 2x 2x REF0 1x 1x 2x 1x 2x 1340G—01/26/10 19 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers PD De-assertion Tstable 3-level latched input If power-up w/ V>2.0V (-0.3V) then use TEST_SEL If power-up w/ Vlow Vth input TEST_MODE is a real time input If TEST_SEL HW pin is 0 during power-up, test mode can be invoked through B6b6. If test mode is invoked by B6b6, only B6b7 is used to select HI-Z or REF/N FS_B/TEST_Mode pin is not used. Cycle power to disable test mode, one shot control SW TEST FS_C/TEST FS_B/TEST ENTRY BIT _SEL _MODE B6b6 HW PIN HW PIN 0 X 0 1 0 X 1 0 X 1 1 X REF/N or HI-Z B6b7 OUTPUT X NORMAL 0 HI-Z 1 REF/N 0 REF/N 1 1 X 1 REF/N 0 X 1 0 HI-Z 0 X 1 1 REF/N B6b6: 1= ENTER TEST MODE, Default = 0 (NORMAL OPERATION) B6b7: 1= REF/N, Default = 0 (HI-Z) IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 20 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers c N SYMBOL A A1 b c D E E1 e h L N a L E1 INDEX AREA E 1 2 α h x 45° D In Millimeters COMMON DIMENSIONS MIN MAX 2.41 2.80 0.20 0.40 0.20 0.34 0.13 0.25 SEE VARIATIONS 10.03 10.68 7.40 7.60 0.635 BASIC 0.38 0.64 0.50 1.02 SEE VARIATIONS 0° 8° In Inches COMMON DIMENSIONS MIN MAX .095 .110 .008 .016 .008 .0135 .005 .010 SEE VARIATIONS .395 .420 .291 .299 0.025 BASIC .015 .025 .020 .040 SEE VARIATIONS 0° 8° VARIATIONS N A 56 -Cb D (inch) MAX 18.55 MIN .720 MAX .730 Reference Doc.: JEDEC Publication 95, MO-118 A1 e D mm. MIN 18.31 10-0034 SEATING PLANE .10 (.004) C IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 21 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers c N L E1 INDEX AREA E 1 2 a D A A2 6.10 mm. Body, 0.50 mm. Pitch TSSOP (240 mil) (20 mil) In Millimeters In Inches SYMBOL COMMON DIMENSIONS COMMON DIMENSIONS MIN MAX MIN MAX A -1.20 -.047 A1 0.05 0.15 .002 .006 A2 0.80 1.05 .032 .041 b 0.17 0.27 .007 .011 c 0.09 0.20 .0035 .008 SEE VARIATIONS SEE VARIATIONS D 8.10 BASIC 0.319 BASIC E E1 6.00 6.20 .236 .244 0.50 BASIC 0.020 BASIC e L 0.45 0.75 .018 .030 SEE VARIATIONS SEE VARIATIONS N α 0° 8° 0° 8° aaa -0.10 -.004 VARIATIONS N A1 56 -C- D mm. MIN 13.90 D (inch) MAX 14.10 MIN .547 MAX .555 Reference Doc.: JEDEC Publication 95, MO-153 e SEATING PLANE b 10-0039 aaa C Ordering Information Part / Order Number 932S421BFLF 932S421BFLFT 932S421BGLF 932S421BGLFT Shipping Packaging Tubes Tape and Reel Tubes Tape and Reel Package 56-pin SSOP 56-pin SSOP 56-pin TSSOP 56-pin TSSOP Temperature 0 to +70° C 0 to +70° C 0 to +70° C 0 to +70° C “LF” after the package code denotes Pb-Free configuration, RoHS compliant. IDTTM PCIe Gen2 and QPI Clock for Intel-Based Servers 1340G—01/26/10 22 ICS932S421B PCIe Gen2 and QPI Clock for Intel-Based Servers Revision History Rev. A B C D E F G Issue Date Description 4/26/2007 1. Updated Single-ended Output Terminations. 2. Release to Final. 6/13/2007 1. Updated CPU output numbers on the block diagram. 9/17/2008 Updated electrical characteristics, PPM and clock period data 11/20/2008 Added 48MHz electrical char table. Corrected Byte 10 bits 4 and 5. They are reserved. For non spread 6/10/2009 PCIe applications such as non-transparent bridging. See the 932S431. 1. Updated Byte 3 table 8/25/2009 2. Added new ordering info table 1/26/2010 Updated document template Page # 10 4 Various 9 15 Various Innovate with IDT and accelerate your future networks. Contact: www.IDT.com TM For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 408-284-6578 pcclockhelp@idt.com Corporate Headquarters Asia Pacific and Japan Europe Integrated Device Technology, Inc. 6024 Silver Creek Valley Road San Jose, CA 95138 United States 800 345 7015 +408 284 8200 (outside U.S.) Integrated Device Technology Singapore (1997) Pte. Ltd. Reg. No. 199707558G 435 Orchard Road #20-03 Wisma Atria Singapore 238877 +65 6 887 5505 IDT Europe, Limited Prime House Barnett Wood Lane Leatherhead, Surrey United Kingdom KT22 7DE +44 1372 363 339 © 2009 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT, ICS, and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA 23 IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.