HA1630D07MMEL-E

HA1631D01/02/03/04 Series Dual CMOS Comparator (Push Pull/Open Drain Output) REJ03D0804-0200 Rev.2.00 Nov 20, 2006 Description The HA1631D01/02/03/04 are low power dual CMOS Comparator featuring low voltage operation with typical current supply of 10 µA/100 µA. They are designed to operate from a single power supply and have push-pull full swing outputs that allow direct connections to logic devices. The Open Drain version HA1631D03/04 enable Output Level shifting through external pull up resistors. Available in MMPAK-8 and TSSOP-8 package. Features • Low supply current HA1631D01/03 : IDDtyp = 5 µA (per comparators) HA1631D02/04 : IDDtyp = 50 µA (per comparators) • Low voltage operation : VDD = 1.8 to 5.5 V • Low input offset voltage : VIOmax = 5 mV • Low input bias current : IIBtyp = 1 pA • Maximum output voltage : VOHmin = 2.9 V (at VDD = 3.0 V) • Input common voltage range includes ground • On-chip ESD protection • Available in MMPAK-8, TSSOP-8 package using Pb free lead frame Ordering Information Type No. Package Name Package Code TTP-8DAV PTSP0008JC-B MMPAK-8 PLSP0008JC-A HA1631D01T HA1631D02T HA1631D03T HA1631D04T HA1631D01MM HA1631D02MM HA1631D03MM HA1631D04MM Rev.2.00 Nov 20, 2006 page 1 of 26 HA1631D01/02/03/04 Series Pin Arrangement VOUT 1 VIN1(–) 2 VIN1(+) 3 8 VDD 7 VOUT2 − + + − VSS 4 6 VIN2(–) 5 VIN2(+) (Top view) Equivalent Circuit (1/2) VDD * IN– IN+ VSS Note: * Not available in Open Drain version (HA1631D03/04) Rev.2.00 Nov 20, 2006 page 2 of 26 OUTPUT HA1631D01/02/03/04 Series Absolute Maximum Ratings (Ta = 25°C) Item Symbol Ratings 7.0 Unit V –VDD to +VDD –0.1 to +VDD V V Supply voltage VDD Differential input voltage Input voltage VIN(diff) VIN Output current Power dissipation IOUT PT 28 192 mA mW Operating temperature Storage temperature Topr Tstg –40 to +85 –55 to +125 °C °C Remarks Note 1 Note 2 TSSOP-8 Notes: 1. Do not apply input voltage exceeding VDD or 7 V. 2. The maximum output current is the maximum allowable value for continuous operation. Electrical Characteristics (Ta = 25°C, VDD = 3.0 V, VSS = 0 V) Item Symbol Min Typ Max Unit Test Conditions Input offset voltage Input bias current VIO IIB — — — (1) 5 — mV pA VIN = VDD/2, RL = 1 MΩ VIN = VDD/2 Input offset current Common mode input voltage range IIO VCM — –0.1 (1) — — 2.1 pA V VIN = VDD/2 Supply current HA1631D01/03 HA1631D02/04 IDD — — 10 100 20 200 µA µA VDD = 3 V, VIN+ = 1 V, VIN– = 0 V Response time HA1631D01 HA1631D01/03 TPLH TPHL — — (1.20) (0.55) — — µs µs HA1631D01 HA1631D01/03 tr tf — — (24) (7) — — ns ns 1 V DC bias, 100 mV overdrive, CL = 15 pF HA1631D02 HA1631D02/04 TPLH TPHL — — (0.33) (0.17) — — µs µs HA1631D02 HA1631D02/04 tr tf — — (12) (7) — — ns ns Output source current (Only for HA1631D01/02) Output sink current IOSOURCE 6 13 — mA Vout = 2.5 V IOSINK 7 14 — mA Vout = 0.5 V Common mode rejection ratio CMRR 60 50 80 70 — — dB dB VIN1 = 0 V, VIN2 = 2 V Power supply rejection ratio Output voltage high (Only for HA1631D01/02) PSRR VOH 60 VDD–0.1 80 — — — dB V VDD1 = 1.8 V, VDD2 = 5 V RL = 10 kΩ to VSS Output voltage low Output leakage current (Only for HA1631D03/04) VOL ILO — — — — 0.1 0.1 V µA RL = 10 kΩ to VDD VIN+ = 1 V, VIN– = 0 V, VO = 3 V Operating voltage range Note: ( ): Design specification Vopr 1.8 — 5.5 V HA1631D01/03 HA1631D02/04 Rev.2.00 Nov 20, 2006 page 3 of 26 HA1631D01/02/03/04 Series Table of Graphs HA1631D01 HA1631D02 HA1631D03 HA1631D04 Test Figure Figure Figure Figure Circuit No. vs. Supply voltage(Out H) 1-1 2-1 3-1 4-1 1 vs. Supply voltage(Out L) 1-2 2-2 3-2 4-2 2 vs. Temperature(Out H) 1-3 2-3 3-3 4-3 1 vs. Frequency(Out H) 1-26 2-26 3-20 4-20 15 Electrical Characteristics Supply current IDD Output high voltage VOH vs. Rload 1-19 2-19 — — 4 Output source current IOSOURCE vs. Output high voltage 1-4 2-4 — — 3 Output low voltage VOL vs. Rload 1-18 2-18 3-15 4-15 6 Output sink current IOSINK vs. Output low voltage 1-5 2-5 3-4 4-4 5 Input offset voltage VIO vs. Supply voltage 1-6 2-6 3-5 4-5 8 vs. Temperature 1-7 2-7 3-6 4-6 7 Common mode input VCM vs. Temperature 1-8 2-8 3-7 4-7 9 PSRR vs. Supply voltage 1-9 2-9 3-8 4-8 11 CMRR vs. Input voltage 1-10 2-10 3-9 4-9 12 IIB vs. Temperature 1-11 2-11 3-10 4-10 10 vs. Input voltage(VDD = 3 V) 1-12 2-12 3-11 4-11 10 vs. Input voltage(VDD = 7 V) 1-13 2-13 3-12 4-12 10 vs. Temperature 1-14 2-14 3-13 4-13 13 voltage range Power supply rejection ratio Common mode rejection ratio Input bias current Falling time Rising time Propagation delay time Cross talk tf tr vs. Cload 1-16 2-16 3-14 4-14 13 Time waveform 1-21 2-21 3-16 4-16 13 vs. Temperature 1-15 2-15 — — 13 vs. Cload 1-17 2-17 — — 13 Time waveform 1-20 2-20 — — 13 TPLH Time waveform 1-22 2-22 — — 13 TPHL Time waveform 1-23 2-23 3-17 4-17 13 VOUT(CH1) vs. Input voltage 1-24 2-24 3-18 4-18 14 VOUT(CH2) vs. Input voltage 1-25 2-25 3-19 4-19 14 Rev.2.00 Nov 20, 2006 page 4 of 26 HA1631D01/02/03/04 Series Main Characteristics (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Figure 1-1 HA1631D01 Supply Current vs. Supply Voltage (Output High) Figure 1-2 HA1631D01 Supply Current vs. Supply Voltage (Output Low) 12.0 Supply Current, IDD (µA) Supply Current, IDD (µA) 12.0 10.0 8.0 6.0 4.0 2.0 0 1 2 3 4 5 Supply Voltage, VDD (V) 6.0 4.0 2.0 0 6 Output High Voltage, VOH (V) 12.0 VDD = 5.5V VDD = 3.0V VDD = 1.8V 10.0 8.0 6.0 4.0 2.0 0 –50 –25 0 25 50 75 1 2 3 4 5 Supply Voltage, VDD (V) 6 Figure 1-4 HA1631D01 Output High Voltage vs. Output Source Current Figure 1-3 HA1631D01 Supply Current vs. Ambient Temperature 6.0 VDD = 5.5V 5.0 4.0 VDD = 1.8V 3.0 2.0 VDD = 3.0V 1.0 0 0 100 30 60 90 120 Ambient Temperature, Ta (°C) Output Source Current, IOSOURCE (mA) Figure 1-5 HA1631D01 Output Low Voltage vs. Output Sink Current Figure 1-6 HA1631D01 Input Offset Voltage vs. Supply Voltage 6.0 Input Offset Voltage, VIO (mV) Supply Current, IDD (µA) 8.0 0 0 Output Low Voltage, VOL (V) 10.0 VDD = 5.5V 5.0 4.0 VDD = 1.8V VDD = 3.0V 3.0 2.0 1.0 0 0 30 60 90 Output Sink Current, IOSINK (mA) Rev.2.00 Nov 20, 2006 page 5 of 26 120 4 3 2 1 0 –1 –2 –3 –4 0 1 2 3 4 Supply Voltage, VDD (V) 5 6 HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) 4 VDD = 1.8V, VIN = 0.9V VDD = 3.0V, VIN = 1.5V VDD = 5.5V, VIN = 2.75V 3 2 1 0 –1 –2 –3 –4 –50 –25 0 25 50 75 Figure 1-8 HA1631D01 Common Mode Input Voltage vs. Ambient Temperature Common Mode Input Voltage, VCM (V) Input Offset Voltage, VIO (mV) Figure 1-7 HA1631D01 Input Offset Voltage vs. Ambient Temperature 100 3.0 VCM+ 2.0 Common Mode Input Voltage Range 1.0 0 VCM– –1.0 –50 Power Supply Rejection Ratio, PSRR (dB) Figure 1-9 HA1631D01 Power Supply Rejection Ratio vs. Supply Voltage 120 100 80 60 40 20 0 1 2 3 4 5 6 Supply Voltage, VDD (V) 7 Common Mode Rejection Ratio, CMRR (dB) Ambient Temperature, Ta (°C) 120 100 80 60 40 20 0 0 2.0 1.0 Input Voltage, VIN (V) 3.0 Figure 1-12 HA1631D01 Input Bias Current vs. Input Voltage 200 Input Bias Current, IIB (pA) 200 Input Bias Current, IIB (pA) 100 Figure 1-10 HA1631D01 Common Mode Rejection Ratio vs. Input Voltage Figure 1-11 HA1631D01 Input Bias Current vs. Ambient Temperature 100 0 –100 –200 –50 –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 0 –100 –200 –25 0 25 50 75 Ambient Temperature, Ta (°C) Rev.2.00 Nov 20, 2006 page 6 of 26 100 0 1.0 2.0 Input Voltage, VIN (V) 3.0 HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Figure 1-13 HA1631D01 Input Bias Current vs. Input Voltage Figure 1-14 HA1631D01 Falling Time vs. Ambient Temperature 20 Falling Time, tf (ns) Input Bias Current, IIB (pA) 200 100 0 –100 –200 0 VDD = 1.8V 15 VDD = 5.5V 10 5 VDD = 3.0V 0 –50 2.0 4.0 6.0 Input Voltage, VIN (V) –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 Figure 1-16 HA1631D01 Falling Time vs. Capacitive Load Figure 1-15 HA1631D01 Rising Time vs. Ambient Temperature 20 50 VDD = 1.8V 40 Falling Time, tf (ns) Rising Time, tr (ns) VDD = 5.5V 30 20 VDD = 3.0V 10 0 –50 15 10 5 0 –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 0 Output Low Voltage, VOL (V) Rising Time, tr (ns) 40 30 20 10 0 20 30 40 Capacitive Load, CL (pF) Rev.2.00 Nov 20, 2006 page 7 of 26 30 40 50 Figure 1-18 HA1631D01 Output Low Voltage vs. Resistor Load 50 10 20 Capacitive Load, CL (pF) Figure 1-17 HA1631D01 Rising Time vs. Capacitive Load 0 10 50 3.0 2.0 1.0 0 10 100k 100 1k 10k Resistor Load, RL (Ω) 1M HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Figure 1-20 HA1631D01 Rising Time tr (Overdrive, ±0.1Vp-p) Output High Voltage, VOH (V) Figure 1-19 HA1631D01 Output High Voltage vs. Resistor Load 3.0 VDD 2.0 1.0 GND 0 10 100 1k 10k 100k Resistor Load, RL (Ω) 1M Figure 1-22 HA1631D01 TPLH Transient Response (Overdrive, ±0.1Vp-p) Figure 1-21 HA1631D01 Falling Time tf (Overdrive, ±0.1Vp-p) VDD Input Voltage CH1 GND Output Voltage CH2 GND Figure 1-23 HA1631D01 TPHL Transient Response (Overdrive, ±0.1Vp-p) CH1 GND Input Voltage Output Voltage CH2 GND Input Offset Voltage (CH1), VIO (mV) GND Figure 1-24 HA1631D01 Input Offset Voltage (CH1) vs. Frequency 4 3 2 1 0 –1 –2 –3 –4 100 1k 10 k 100 k Frequency, f (Hz) Rev.2.00 Nov 20, 2006 page 8 of 26 1M HA1631D01/02/03/04 Series Figure 1-26 HA1631D01 Supply Current vs. Frequency (Output High) Figure 1-25 HA1631D01 Input Offset Voltage (CH2) vs. Frequency 4 600 3 Supply Current, IDD (µA) Input Offset Voltage (CH2), VIO (mV) (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) 2 1 0 –1 –2 –3 –4 100 1k 10 k 100 k Frequency, f (Hz) Rev.2.00 Nov 20, 2006 page 9 of 26 1M 500 400 VDD = 2.5V, VSS = –2.5V 300 VDD = 2V, VSS = –1V 200 VDD = 1.3V, VSS = –0.5V 100 0 0.1 1 10 Frequency, f (kHz) 100 HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Figure 2-2 HA1631D02 Supply Current vs. Supply Voltage (Output Low) Figure 2-1 HA1631D02 Supply Current vs. Supply Voltage (Output High) 120 Supply Current, IDD (µA) Supply Current, IDD (µA) 120 100 80 60 40 20 0 100 80 60 40 20 0 0 1 2 3 4 5 0 6 1 Supply Voltage, VDD (V) Output High Voltage, VOH (V) Supply Current, IDD (µA) VDD = 5.5V 100 VDD = 3.0V 80 60 VDD = 1.8V 40 20 0 –50 –25 0 25 50 75 4.0 VDD = 3.0V 2.0 1.0 0 0 VDD = 1.8V VDD = 3.0V 2.0 1.0 0 30 60 90 Output Sink Current, IOSINK (mA) Rev.2.00 Nov 20, 2006 page 10 of 26 120 30 60 90 120 Output Source Current, IOSOURCE (mA) Figure 2-6 HA1631D02 Input Offset Voltage vs. Supply Voltage Input Offset Voltage, VIO (mV) Output Low Voltage, VOL (V) VDD = 5.5V 0 6 VDD = 1.8V 3.0 100 6.0 3.0 5 VDD = 5.5V 5.0 Figure 2-5 HA1631D02 Output Low Voltage vs. Output Sink Current 4.0 4 6.0 Ambient Temperature, Ta (°C) 5.0 3 Figure 2-4 HA1631D02 Output High Voltage vs. Output Source Current Figure 2-3 HA1631D02 Supply Current vs. Ambient Temperature 120 2 Supply Voltage, VDD (V) 4 3 2 1 0 –1 –2 –3 –4 0 1 2 3 4 Supply Voltage, VDD (V) 5 6 HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Common Mode Input Voltage, VCM (V) 4 VDD = 1.8V, VIN = 0.9V VDD = 3.0V, VIN = 1.5V VDD = 5.5V, VIN = 2.75V 3 2 1 0 –1 –2 –3 –4 –50 –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 Power Supply Rejection Ratio, PSRR (dB) Figure 2-9 HA1631D02 Power Supply Rejection Ratio vs. Supply Voltage 120 100 80 60 40 20 0 1 2 3 4 5 6 Supply Voltage, VDD (V) Figure 2-8 HA1631D02 Common Mode Input Voltage vs. Ambient Temperature 7 Common Mode Rejection Ratio, CMRR (dB) Input Offset Voltage, VIO (mV) Figure 2-7 HA1631D02 Input Offset Voltage vs. Ambient Temperature 3.0 VCM+ 2.0 Common Mode Input Voltage Range 1.0 VCM– 0.0 –1.0 –50 120 100 80 60 40 20 0 0 1.0 2.0 Input Voltage, VIN (V) 3.0 Figure 2-12 HA1631D02 Input Bias Current vs. Input Voltage 200 200 Input Bias Current, IIB (pA) Input Bias Current, IIB (pA) 100 Figure 2-10 HA1631D02 Common Mode Rejection Ratio vs. Input Voltage Figure 2-11 HA1631D02 Input Bias Current vs. Ambient Temperature 100 0 –100 –200 –50 –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 0 –100 –200 –25 0 25 50 75 Ambient Temperature, Ta (°C) Rev.2.00 Nov 20, 2006 page 11 of 26 100 0 1.0 2.0 Input Voltage, VIN (V) 3.0 HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Figure 2-14 HA1631D02 Falling Time vs. Ambient Temperature Figure 2-13 HA1631D02 Input Bias Current vs. Input Voltage 20 Falling Time, tf (ns) Input Bias Current, IIB (pA) 200 100 0 –100 VDD = 1.8V 15 10 VDD = 3.0V 5 VDD = 5.5V 0 –50 –200 0 2.0 4.0 6.0 Input Voltage, VIN (V) 25 50 75 100 Figure 2-16 HA1631D02 Falling Time vs. Capacitive Load 20 Falling Time, tf (ns) 20 Rising Time, tr (ns) 0 Ambient Temperature, Ta (°C) Figure 2-15 HA1631D02 Rising Time vs. Ambient Temperature 15 VDD = 1.8V 10 VDD = 5.5V VDD = 3.0V 5 0 –50 15 10 5 0 –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 0 Output Low Voltage, VOL (V) 40 30 20 10 0 10 20 30 40 Capacitive Load, CL (pF) Rev.2.00 Nov 20, 2006 page 12 of 26 20 30 40 50 Figure 2-18 HA1631D02 Output Low Voltage vs. Resistor Load 50 0 10 Capacitive Load, CL (pF) Figure 2-17 HA1631D02 Rising Time vs. Capacitive Load Rising Time, tr (ns) –25 50 3.0 2.0 1.0 0 10 100 1k 10k 100k Resistor Load, RL (Ω) 1M HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Figure 2-20 HA1631D02 Rising Time tr (Overdrive, ±0.1Vp-p) Output High Voltage, VOH (V) Figure 2-19 HA1631D02 Output High Voltage vs. Resistor Load 3.0 VDD 2.0 1.0 GND 0 10 100 1k 10k 100k Resistor Load, RL (Ω) 1M Figure 2-22 HA1631D02 TPLH Transient Response (Overdrive, ±0.1Vp-p) Figure 2-21 HA1631D02 Falling Time tf (Overdrive, ±0.1Vp-p) VDD Input Voltage CH1 GND Output Voltage GND Figure 2-23 HA1631D02 TPHL Transient Response (Overdrive, ±0.1Vp-p) Input Voltage CH1 GND Output Voltage CH2 GND Rev.2.00 Nov 20, 2006 page 13 of 26 Input Offset Voltage (CH1), VIO (mV) CH2 GND Figure 2-24 HA1631D02 Input Offset Voltage (CH1) vs. Frequency 4 3 2 1 0 –1 –2 –3 –4 100 1k 10 k 100 k Frequency, f (Hz) 1M HA1631D01/02/03/04 Series Figure 2-26 HA1631D02 Supply Current vs. Frequency (Output High) Figure 2-25 HA1631D02 Input Offset Voltage (CH2) vs. Frequency 4 300 3 Supply Current, IDD (µA) Input Offset Voltage (CH2), VIO (mV) (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) 2 1 0 –1 –2 –3 –4 100 1k 10 k 100 k Frequency, f (Hz) Rev.2.00 Nov 20, 2006 page 14 of 26 1M 250 VDD = 2.5V, VSS = –2.5V VDD = 2V, VSS = –1V 200 VDD = 1.3V, VSS = –0.5V 150 100 50 0 0.1 1 10 Frequency, f (kHz) 100 HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Figure 3-1 HA1631D03 Supply Current vs. Supply Voltage (Output High) Figure 3-2 HA1631D03 Supply Current vs. Supply Voltage (Output Low) 12.0 Supply Current, IDD (µA) Supply Current, IDD (µA) 12.0 10.0 8.0 6.0 4.0 2.0 6.0 4.0 2.0 Supply Voltage, VDD (V) 2 3 4 5 Supply Voltage, VDD (V) Figure 3-3 HA1631D03 Supply Current vs. Ambient Temperature Figure 3-4 HA1631D03 Output Low Voltage vs. Output Sink Current 0 1 2 3 4 5 Output Low Voltage, VOL (V) VDD = 5.5V 10.0 VDD = 3.0V 8.0 6.0 VDD = 1.8V 4.0 2.0 0 –50 –25 0 25 50 75 0 6 12.0 Supply Current, IDD (µA) 8.0 0 0 1 6 6.0 VDD = 5.5V 5.0 4.0 VDD = 1.8V VDD = 3.0V 3.0 2.0 1.0 0 100 0 30 60 90 120 Ambient Temperature, Ta (°C) Output Sink Current, IOSINK (mA) Figure 3-5 HA1631D03 Input Offset Voltage vs. Supply Voltage Figure 3-6 HA1631D03 Input Offset Voltage vs. Ambient Temperature 4 Input Offset Voltage, VIO (mV) Input Offset Voltage, VIO (mV) 10.0 3 2 1 0 –1 –2 –3 –4 0 1 2 3 4 5 Supply Voltage, VDD (V) Rev.2.00 Nov 20, 2006 page 15 of 26 6 4 3 2 VDD = 1.8V, VIN = 0.9V VDD = 3.0V, VIN = 1.5V VDD = 5.5V, VIN = 2.75V 1 0 –1 –2 –3 –4 –50 –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Common Mode Rejection Ratio, CMRR (dB) 3.0 VCM+ 2.0 Common Mode Input Voltage Range 1.0 VCM– 0 –1.0 –50 –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 Figure 3-8 HA1631D03 Power Supply Rejection Ratio vs. Supply Voltage Power Supply Rejection Ratio, PSRR (dB) Common Mode Input Voltage, VCM (V) Figure 3-7 HA1631D03 Common Mode Input Voltage vs. Ambient Temperature 120 100 80 60 40 20 0 1 80 60 40 7 200 Input Bias Current, IIB (pA) 100 3 4 5 6 Supply Voltage, VDD (V) Figure 3-10 HA1631D03 Input Bias Current vs. Ambient Temperature Figure 3-9 HA1631D03 Common Mode Rejection Ratio vs. Input Voltage 120 2 100 0 –100 20 0 0 2.0 1.0 Input Voltage, VIN (V) 3.0 –200 –50 0 25 50 75 200 Input Bias Current, IIB (pA) 200 100 0 100 0 –100 –100 –200 –200 0 1.0 2.0 Input Voltage, VIN (V) Rev.2.00 Nov 20, 2006 page 16 of 26 100 Figure 3-12 HA1631D03 Input Bias Current vs. Input Voltage Figure 3-11 HA1631D03 Input Bias Current vs. Input Voltage Input Bias Current, IIB (pA) –25 Ambient Temperature, Ta (°C) 3.0 0 2.0 4.0 6.0 Input Voltage, VIN (V) HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Figure 3-14 HA1631D03 Falling Time vs. Capacitive Load Figure 3-13 HA1631D03 Falling Time vs. Ambient Temperature 20 VDD = 1.8V Falling Time, tf (ns) Falling Time, tf (ns) 20 15 VDD = 3.0V 10 5 VDD = 5.5V 0 –50 15 10 5 0 –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 0 VDD 2.0 1.0 GND 0 10 100 1k 10k 100k Resistor Load, RL (Ω) Figure 3-17 HA1631D03 TPHL Transient Response (Overdrive, ±0.1Vp-p) Input Voltage CH1 GND Output Voltage CH2 GND Rev.2.00 Nov 20, 2006 page 17 of 26 1M Input Offset Voltage (CH1), VIO (mV) Output Low Voltage, VOL (V) 50 Figure 3-16 HA1631D03 Falling Time tf (Overdrive, ±0.1Vp-p) Figure 3-15 HA1631D03 Output Low Voltage vs. Resistor Load 3.0 10 20 30 40 Capacitive Load, CL (pF) Figure 3-18 HA1631D03 Input Offset Voltage (CH1) vs. Frequency 4 3 2 1 0 –1 –2 –3 –4 100 1k 10 k 100 k Frequency, f (Hz) 1M HA1631D01/02/03/04 Series Figure 3-20 HA1631D03 Supply Current vs. Frequency (Output High) Figure 3-19 HA1631D03 Input Offset Voltage (CH2) vs. Frequency 4 300 3 Supply Current, IDD (µA) Input Offset Voltage (CH2), VIO (mV) (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) 2 1 0 –1 –2 –3 –4 100 1k 10 k 100 k Frequency, f (Hz) Rev.2.00 Nov 20, 2006 page 18 of 26 1M 250 200 VDD = 2.5V, VSS = –2.5V 150 VDD = 2V, VSS = –1V 100 VDD = 1.3V, VSS = –0.5V 50 0 0.1 1 10 Frequency, f (kHz) 100 HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Figure 4-1 HA1631D04 Supply Current vs. Supply Voltage (Output High) Figure 4-2 HA1631D04 Supply Current vs. Supply Voltage (Output Low) 120 Supply Current, IDD (µA) Supply Current, IDD (µA) 120 100 80 60 40 20 0 1 2 3 4 5 60 40 20 6 0 1 2 3 4 5 6 Supply Voltage, VDD (V) Supply Voltage, VDD (V) Figure 4-3 HA1631D04 Supply Current vs. Ambient Temperature Figure 4-4 HA1631D04 Output Low Voltage vs. Output Sink Current Output Low Voltage, VOL (V) 120 Supply Current, IDD (µA) 80 0 0 VDD = 5.5V 100 VDD = 3.0V 80 60 VDD = 1.8V 40 20 0 –50 –25 0 25 50 75 6.0 5.0 VDD = 5.5V 4.0 VDD = 1.8V VDD = 3.0V 3.0 2.0 1.0 0 100 0 30 60 90 120 Ambient Temperature, Ta (°C) Output Sink Current, IOSINK (mA) Figure 4-5 HA1631D04 Input Offset Voltage vs. Supply Voltage Figure 4-6 HA1631D04 Input Offset Voltage vs. Ambient Temperature 4 Input Offset Voltage, VIO (mV) Input Offset Voltage, VIO (mV) 100 3 2 1 0 –1 –2 –3 –4 0 1 2 3 4 5 Supply Voltage, VDD (V) Rev.2.00 Nov 20, 2006 page 19 of 26 6 4 3 2 VDD = 1.8V, VIN = 0.9V VDD = 3.0V, VIN = 1.5V VDD = 5.5V, VIN = 2.75V 1 0 –1 –2 –3 –4 –50 –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Common Mode Rejection Ratio, CMRR (dB) 3.0 VCM+ 2.0 Common Mode Input Voltage Range 1.0 VCM– 0 –1.0 –50 –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 Figure 4-8 HA1631D04 Power Supply Rejection Ratio vs. Supply Voltage Power Supply Rejection Ratio, PSRR (dB) Common Mode Input Voltage, VCM (V) Figure 4-7 HA1631D04 Common Mode Input Voltage vs. Ambient Temperature 120 100 80 60 40 20 0 1 80 60 40 4 5 6 7 Figure 4-10 HA1631D04 Input Bias Current vs. Ambient Temperature 200 Input Bias Current, IIB (pA) 100 3 Supply Voltage, VDD (V) Figure 4-9 HA1631D04 Common Mode Rejection Ratio vs. Input Voltage 120 2 100 0 –100 20 0 0 2.0 1.0 Input Voltage, VIN (V) 3.0 –200 –50 Figure 4-12 HA1631D04 Input Bias Current vs. Input Voltage Figure 4-11 HA1631D04 Input Bias Current vs. Input Voltage 200 Input Bias Current, IIB (pA) 200 Input Bias Current, IIB (pA) –25 0 25 50 75 Ambient Temperature, Ta (°C) 100 0 100 0 –100 –100 –200 –200 0 1.0 2.0 Input Voltage, VIN (V) Rev.2.00 Nov 20, 2006 page 20 of 26 3.0 0 2.0 4.0 6.0 Input Voltage, VIN (V) 100 HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) Figure 4-14 HA1631D04 Falling Time vs. Capacitive Load Figure 4-13 HA1631D04 Falling Time vs. Ambient Temperature 20 15 Falling Time, tf (ns) Falling Time, tf (ns) 20 VDD = 1.8V 10 VDD = 3.0V 5 15 10 5 VDD = 5.5V 0 –50 0 –25 0 25 50 75 Ambient Temperature, Ta (°C) 0 100 20 30 40 50 Capacitive Load, CL (pF) Figure 4-16 HA1631D04 Falling Time tf (Overdrive, ±0.1Vp-p) Figure 4-15 HA1631D04 Output Low Voltage vs. Resistor Load 3.0 VDD 2.0 1.0 GND 0 10 100 1k 10k 100k Resistor Load, RL (Ω) Figure 4-17 HA1631D04 TPHL Transient Response (Overdrive, ±0.1Vp-p) Input Voltage CH1 GND Output Voltage CH2 GND 1M Input Offset Voltage (CH1), VIO (mV) Output Low Voltage, VOL (V) 10 Figure 4-18 HA1631D04 Input Offset Voltage (CH1) vs. Frequency 4 3 2 1 0 –1 –2 –3 –4 100 1k 10 k 100 k Frequency, f (Hz) Rev.2.00 Nov 20, 2006 page 21 of 26 1M HA1631D01/02/03/04 Series Figure 4-20 HA1631D04 Supply Current vs. Frequency (Output High) Figure 4-19 HA1631D04 Input Offset Voltage (CH2) vs. Frequency 4 300 3 Supply Current, IDD (µA) Input Offset Voltage (CH2), VIO (mV) (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) 2 1 0 –1 –2 –3 –4 100 1k 10 k 100 k Frequency, f (Hz) Rev.2.00 Nov 20, 2006 page 22 of 26 1M 250 VDD = 2.5V, VSS = –2.5V VDD = 2V, VSS = –1V 200 VDD = 1.3V, VSS = –0.5V 150 100 50 0 0.1 1 10 Frequency, f (kHz) 100 HA1631D01/02/03/04 Series Test Circuits (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) 1. Supply Current, IDD (Output High) VDD 2. Supply Current, IDD (Output Low) VDD A + − A + − + − 1V 1V 3. Output Source Current, IOSOURCE VDD 4. Output Voltage High, VOH VDD + − + − 1V VOUT 1V 5. Output Sink Current, IOSINK VDD RLOAD 6. Output Voltage Low, VOL VDD + − VOUT 1V 7. Input Offset Voltage, VIO VDD 10kΩ 1kΩ + − 1kΩ 1MΩ RLOAD + − 1V VIN + − 1MΩ 1.5V Note: VIO = VOUT – 1.5 V Rev.2.00 Nov 20, 2006 page 23 of 26 8. Input Offset Voltage vs. Supply Voltage VDD Only for Open Drain 1kΩ + − VOUT 100µF 10kΩ 1kΩ 1MΩ 1MΩ –VDD Only for Open Drain VOUT 100µF HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) 9. Common Mode Input Voltage, VCM VDD 10kΩ 1kΩ + − VIN 1kΩ 1MΩ 10. Input Bias Current, IIB VDD = 3V, 7V Only for Open Drain A VOUT 100µF 1MΩ VCML VIO VIN = 0V 1.5V + − VIN VIN VCMH Note: VCML and VCMH are values of VIN when VIO changes more than 50dB taking VIN = 0V as reference. 11. Power Supply Rejection Ratio, PSRR VDD/2 10kΩ 1kΩ Only for Open Drain + − 1kΩ 1MΩ VOUT 100µF 1MΩ –VDD/2 Measure Calculate VIO PSRR Calculation Point |(VIO2 − VIO1)| 1.8V VOUT1 VIO1 = VOUT1/1000 PSRR = 20log 5.5V − 1.8V 5.5V VOUT2 VIO2 = VOUT2/1000 VDD 12. Common Mode Rejection Ratio, CMRR VDD/2 10kΩ 1kΩ Only for Open Drain + − VIN 1kΩ 1MΩ 1MΩ VOUT 100µF –VDD/2 Rev.2.00 Nov 20, 2006 page 24 of 26 VIN −1.5V 0.5V Measure Point Calculate VIO CMRR Calculation |(VIO2 − VIO1)| VOUT1 VIO1 = VOUT1/1000 CMRR = 20log 0.5V − (−1.5V) VOUT2 VIO2 = VOUT2/1000 HA1631D01/02/03/04 Series (unless otherwise noted, VDD = 3 V, VSS = 0 V, Ta = 25°C) 13. Response Time tr, tf and Delay Time TPHL, TPLH VDD = 2V Only for Open Drain 10kΩ + − ±0.1V VOUT 50Ω CL = 15pF VSS = –1V 50% 50% input input 90% 50% 90% output 50% output 10% 10% TPLH TPHL tr tf Only for Push Pull HA1631D01/02 50% 50% input input 90% output 50% 50% output 10% TPLH tf TPHL Only for Open Drain HA1631D03/04 14. Cross Talk VDD = 1.5V ±0.1V 50Ω + − 15. Supply Current, IDD (Output High) vs. Frequency VDD = 1.3V, 2V, 2.5V Only for Open Drain VIN' 1kΩ A 10kΩ + 100kΩ − VSS = –1.5V VIN Note: VIO = VIN' Rev.2.00 Nov 20, 2006 page 25 of 26 VOUT VOUT VDD VSS VIN' + − Freq. ±0.1V + − 50Ω VSS = –0.5V, –1V, –2.5V HA1631D01/02/03/04 Series Package Dimensions JEITA Package Code P-TSSOP8-4.4x3-0.65 RENESAS Code PTSP0008JC-B *1 Previous Code TTP-8DAV MASS[Typ.] 0.034g D F 8 5 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. c HE *2 E bp Terminal cross section ( Ni/Pd/Au plating ) Reference Symbol Index mark L1 1 4 e *3 bp x M θ A1 A Z L Detail F y Package Name MMPAK-8 JEITA Package Code P-LSOP8-2.8 x 2.95 - 0.65 RENESAS Code PLSP0008JC-A Previous Code  0.13 +0.12 -0.03 0.6 0 to 0.1 0.65 0.1 M 0.3 1.1 ± 0.1 1.95 0.1 Rev.2.00 Nov 20, 2006 page 26 of 26 0.2 +0.1 -0.05 Min Nom Max 3.00 3.30 4.40 0.03 0.07 0.10 1.10 0.15 0.20 0.25 0.10 0.15 0.20 0° 8° 6.20 6.40 6.60 0.65 0.13 0.10 0.805 0.40 0.50 0.60 1.00 Unit: mm 2.8 ± 0.1 4.0 ± 0.3 2.95 ± 0.2 MASS[Typ.] 0.02 g D E A2 A1 A bp b1 c c1 θ HE e x y Z L L1 Dimension in Millimeters Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: (408) 382-7500, Fax: (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: (1628) 585-100, Fax: (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: (21) 5877-1818, Fax: (21) 6887-7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2265-6688, Fax: 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: (2) 2715-2888, Fax: (2) 2713-2999 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: 6213-0200, Fax: 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: (2) 796-3115, Fax: (2) 796-2145 Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: 7955-9390, Fax: 7955-9510 © 2006. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .7.0 To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.com April 1st, 2010 Renesas Electronics Corporation Issued by: Renesas Electronics Corporation (http://www.renesas.com) Send any inquiries to http://www.renesas.com/inquiry. Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. Renesas Electronics products are classified according to the following three quality grades: “Standard”, “High Quality”, and “Specific”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as “Specific” without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific” or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is “Standard” unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. “Standard”: 8. 9. 10. 11. 12. Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. “High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anticrime systems; safety equipment; and medical equipment not specifically designed for life support. “Specific”: Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majorityowned subsidiaries. (Note 2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.