HA7-5137A-5

DATASHEET HA-5137A FN2908 Rev 5.00 April 2000 63MHz, Ultra-Low Noise Precision Operational Amplifier The HA-5137 operational amplifier features an unparalleled combination of precision DC and wideband high speed characteristics. Utilizing the Intersil Dielectric Isolation technology and advanced processing techniques, this unique design unites low noise  3nV  Hz  precision instrumentation performance with high speed (20V/s) wideband capability. This amplifier’s impressive list of features include low VOS (10V), wide gain bandwidth (63MHz), high open loop gain (1800V/mV), and high CMRR (126dB). Additionally, this flexible device operates over a wide supply range (5V to 20V) while consuming only 140mW of power. Using the HA-5137 allows designers to minimize errors while maximizing speed and bandwidth in applications requiring gains greater than five. This device is ideally suited for low level transducer signal amplifier circuits. Other applications which can utilize the HA-5137’s qualities include instrumentation amplifiers, pulse or RF amplifiers, audio preamplifiers, and signal conditioning circuits. This device can easily be used as a design enhancement by directly replacing the 725, OP25, OP06, OP07, OP27 and OP37 where gains are greater than five. For the military grade product, refer to the HA-5137/883 data sheet. Features • Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/s • Wide Gain Bandwidth (AV 5) . . . . . . . . . . . . . . . 63MHz • Low Noise . . . . . . . . . . . . . . . . . . . . . . 3nV/ Hz at 1kHz • Low VOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10V • High CMRR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126dB • High Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1800V/mV Applications • High Speed Signal Conditioners • Wide Bandwidth Instrumentation Amplifiers • Low Level Transducer Amplifiers • Fast, Low Level Voltage Comparators • Highest Quality Audio Preamplifiers • Pulse/RF Amplifiers • For Further Design Ideas See Application Note AN553 Ordering Information PART NUMBER HA7-5137A-5 Pinout TEMP. RANGE (oC) 0 to 75 PACKAGE 8 Ld CERDIP PKG. NO. F8.3A HA-5137A (CERDIP) TOP VIEW BAL 1 -IN 2 +IN 3 V- 4 FN2908 Rev 5.00 April 2000 + 8 BAL 7 V+ 6 OUT 5 NC Page 1 of 9 HA-5137A Absolute Maximum Ratings TA = 25oC Thermal Information Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 44V Differential Input Voltage (Note 1) . . . . . . . . . . . . . . . . . . . . . . . 0.7V Output Current . . . . . . . . . . . . . . . . . . . . Full Short Circuit Protection Thermal Resistance (Typical, Note 2) Operating Conditions Temperature Range HA-5137A-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC JA (oC/W) JC (oC/W) CERDIP Package. . . . . . . . . . . . . . . . . 115 28 Maximum Junction Temperature (Hermetic Package) . . . . . . . 175oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. For differential input voltages greater than 0.7V, the input current must be limited to 25mA to protect the back-to-back input diodes. 2. JA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications VSUPPLY = 15V, CL  50pF, RS  100 PARAMETER TEST CONDITIONS TEMP. (oC) MIN TYP MAX UNITS INPUT CHARACTERISTICS Offset Voltage Average Offset Voltage Drift Bias Current 25 - 10 25 V Full - 30 60 V Full - 0.2 0.6 V/oC 25 - 10 40 nA Full - 20 60 nA 25 - 7 35 nA Full - 15 50 nA Common Mode Range Full 10.3 11.5 - V Differential Input Resistance (Note 3) 25 1.5 6 - M Offset Current Input Noise Voltage (Note 4) 0.1Hz to 10Hz 25 - 0.08 0.18 VP-P Input Noise Voltage Density (Note 5) f = 10Hz 25 - 3.5 8.0 f = 100Hz 25 - 3.1 4.5 nV/ Hz nV/ Hz f = 1000Hz 25 - 3.0 3.8 nV/ Hz f = 10Hz 25 - 1.7 4.0 pA/ Hz f = 100Hz 25 - 1.0 2.3 pA/ Hz f = 1000Hz 25 - 0.4 0.6 pA/ Hz RL = 2k, VOUT = 10V 25 1000 1800 - V/mV Full 600 1200 - V/mV VCM = 10V Full 114 126 - dB 25 5 - - V/V f = 10kHz 25 60 80 - MHz f = 1MHz 25 - 63 - MHz RL = 600 25 10.0 11.5 - V RL = 2k Full 11.7 13.8 - V 25 220 320 - kHz Open Loop 25 - 70 -  25 16.5 25 - mA Input Noise Current Density (Note 5) TRANSFER CHARACTERISTICS Large Signal Voltage Gain Common Mode Rejection Ratio Minimum Stable Gain Gain-Bandwidth-Product OUTPUT CHARACTERISTICS Output Voltage Swing Full Power Bandwidth (Note 6) Output Resistance Output Current TRANSIENT RESPONSE (Note 7) Rise Time 25 - - 100 ns Slew Rate VOUT = 3V 25 14 20 - V/s Settling Time Note 8 25 - 1.0 - s 25 - 20 40 % 25 - 3.5 - mA Full - - 4.0 mA Overshoot POWER SUPPLY CHARACTERISTICS Supply Current FN2908 Rev 5.00 April 2000 Page 2 of 9 HA-5137A Electrical Specifications VSUPPLY = 15V, CL  50pF, RS  100 (Continued) PARAMETER TEST CONDITIONS VS = 4V to 18V Power Supply Rejection Ratio TEMP. (oC) MIN TYP MAX UNITS Full - 2 4 V/V NOTES: 3. This parameter value is based upon design calculations. 4. Refer to Typical Performance section of the data sheet. 5. The limits for this parameter are based on lab characterization, and reflect lot-to-lot variation. Slew Rate 6. Full power bandwidth guaranteed based on slew rate measurement using: FPBW = ----------------------------- . 2V PEAK 7. Refer to Test Circuits section of the data sheet. 8. Settling time is specified to 0.1% of final value for a 10V output step and AV = -5. Test Circuits and Waveforms IN + OUT - 1.6k 50pF 400 FIGURE 1. LARGE AND SMALL SIGNAL RESPONSE TEST CIRCUIT IN IN OUT OUT Vertical Scale: Input = 1V/Div. Output = 5V/Div. Horizontal Scale: 1s/Div. Vertical Scale: Input = 20mV/Div. Output = 100mV/Div. Horizontal Scale: 100ns/Div. LARGE SIGNAL RESPONSE SMALL SIGNAL RESPONSE +15V 2N4416 1000 TO OSCILLOSCOPE 5k 2k +15V 400 IN NOTES: + OUT - 50pF -15V 2k 9. AV = -5. 10. Feedback and summing resistors should be 0.1% matched. 11. Clipping diodes are optional. HP5082-2810 recommended. FIGURE 2. SETTLING TIME TEST CIRCUIT FN2908 Rev 5.00 April 2000 Page 3 of 9 HA-5137A FN2908 Rev 5.00 April 2000 Schematic Diagram V+ 7 1 R25 R1 R16 R15 C7 8 BALANCE R2 QP32 QP37 R20 QP35 D1 QN45 R21 QP43 R17 QP38 QP44 QP55 C5 QN19 QD8 QN46 C4 QN13 QP56 QN47 R1A QN3 QN2 QN12 QP36 QP27 QP26 QD59 R3 QD41 QN2A 6 QN1A QN18 QN1 QP40 QN6 QN48 QN25 QN49 R8 R10 Page 4 of 9 QN11 SUBSTRATE 3 2 +INPUT -INPUT C3 QN5 QN50 C2 R6 QN10 V- QP30 R19 QN42A 4 R13 QD34 QN7 QN42 R4 R5 R12 R18 QN39 QD60 QN20 QD33 QP26 QD23 QN24 QN57 R7 QP16 OUTPUT QP36A QD22 QZ58 QN29 QP17 QN4 QD54 QD53 R9 R24 QD9 C6 QN15 C1 QN52 QN51 R14 QN14 R2A R22 R23 QP21 HA-5137A Application Information RP 10K 1 2 3 8 7 + V+ 6 4 5 Tested Offset Adjustment Range is |VOS + 1mV| minimum referred to output. Typical range is 4mV with RP = 10k. NOTE: FIGURE 3. SUGGESTED OFFSET VOLTAGE ADJUSTMENT CS R1 + - R2 R1 + R3 R3 R2 C3 NOTE: Low resistances are preferred for low noise applications as a 1k resistor has 4nV/Hz of thermal noise. Total resistances of greater than 10k on either input can reduce stability. In most high resistance applications, a few picofarads of capacitance across the feedback resistor will improve stability. FIGURE 4. SUGGESTED STABILITY CIRCUITS Unless Otherwise Specified: TA = 25oC, VSUPPLY = 15V 12 30 10 NOISE VOLTAGE (nV/Hz) OFFSET VOLTAGE (V) 20 0 -10 -20 -30 -40 -60 -60 10 5 8 4 6 3 NOISE VOLTAGE 4 2 -50 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (oC) FIGURE 5. OFFSET VOLTAGE DRIFT vs TEMPERATURE FN2908 Rev 5.00 April 2000 6 VS = 15V, TA = 25oC NOISE CURRENT 0 1 10 100 1K 10K 100K 2 1 0 1M FREQUENCY (Hz) FIGURE 6. NOISE CHARACTERISTICS Page 5 of 9 NOISE CURRENT (pA/Hz) Typical Performance Curves HA-5137A Typical Performance Curves 140 TA = 25oC 0.12 120 0.1 100 CMRR (dB) INPUT NOISE VOLTAGE (VP-P) 0.14 Unless Otherwise Specified: TA = 25oC, VSUPPLY = 15V (Continued) 0.08 0.06 80 60 0.04 40 0.02 20 0 4 6 8 10 12 14 16 18 0 10 20 100 1K 10K 100K 1M 10M FREQUENCY (Hz) SUPPLY VOLTAGE (V) FIGURE 8. CMRR vs FREQUENCY FIGURE 7. NOISE vs SUPPLY VOLTAGE 2.60 1.10 BANDWIDTH AND SLEW RATE (NORMALIZED TO 1 AT 15V) 2.58 SUPPLY CURRENT (mA) 2.56 2.54 2.52 2.50 2.48 2.46 2.44 1.00 BANDWIDTH 0.90 -SLEW RATE 0.80 +SLEW RATE 0.70 0.60 2.42 4 6 8 10 12 14 16 18 0.50 20 5 10 SUPPLY VOLTAGE (V) FIGURE 9. SUPPLY CURRENT vs SUPPLY VOLTAGE 20 FIGURE 10. BANDWIDTH AND SLEW RATE vs SUPPLY VOLTAGE 140 40 30 100 GAIN (dB) 120 PSRR (dB) 15 SUPPLY VOLTAGE (V) -PSRR 80 60 +PSRR GAIN 20 10 0 0 PHASE -10 90 -20 40 20 0 10 180 100 1K 10K 100K FREQUENCY (Hz) FIGURE 11. PSRR vs FREQUENCY FN2908 Rev 5.00 April 2000 1M 10M 100 1K 10K 100K 1M 10M PHASE (DEGREES) 2.40 100M FREQUENCY (Hz) FIGURE 12. CLOSED LOOP GAIN AND PHASE vs FREQUENCY Page 6 of 9 HA-5137A Typical Performance Curves 17 1.05 SLEW RATE NORMALIZED TO 1 AT 30oC TA = 25oC 16 AVOL (100kV/V) AND VOUT (V) Unless Otherwise Specified: TA = 25oC, VSUPPLY = 15V (Continued) AVOL 15 14 13 VOUT 12 11 10 9 8 7 6 5 4 2 0 4 6 8 1.04 1.03 1.02 1.01 1.0 0.99 0.98 0.97 0.96 0.95 -60 10 RL = 2K, CL = 50pF, TA = 25oC -40 -20 FIGURE 13. AVOL AND VOUT vs LOAD RESISTANCE 28 40 60 80 100 120 RL = 2K, CL = 50pF, TA = 25oC 24 OUTPUT VOLTAGE (VP-P) 2.80 SUPPLY CURRENT (mA) 20 FIGURE 14. NORMALIZED SLEW RATE vs TEMPERATURE VO = 0V, VS = 15V 2.82 0 TEMPERATURE (oC) LOAD RESISTANCE (k) 2.78 2.76 2.74 2.72 2.70 20 16 12 8 4 2.68 -55 25 TEMPERATURE (oC) 125 FIGURE 15. SUPPLY CURRENT vs TEMPERATURE 0 0.4 0.8 1.2 1.6 FREQUENCY (MHz) 2 FIGURE 16. VOUT MAX (UNDISTORTED SINEWAVE OUTPUT) vs FREQUENCY 140 120 GAIN 80 60 40 20 0 PHASE 0 -45 -90 -135 10 100 1K 10K 100K 1M 10M -180 100M PHASE SHIFT (DEGREES) GAIN (dB) 100 FREQUENCY (Hz) FIGURE 17. OPEN LOOP GAIN AND PHASE vs FREQUENCY FN2908 Rev 5.00 April 2000 ACL = 25,000V/V Horizontal Scale = 1s/Div. Vertical Scale = 0.002V/Div., EN = 0.08VP-P RTI FIGURE 18. PEAK-TO-PEAK NOISE VOLTAGE (0.1Hz TO 10Hz) Page 7 of 9 HA-5137A Die Characteristics DIE DIMENSIONS: PASSIVATION: Type: Nitride (Si3N4) over Silox (SiO2, 5% Phos.) Silox Thickness: 12kÅ 2kÅ Nitride Thickness: 3.5kÅ 1.5kÅ 104 mils x 65 mils x 19 mils 2650m x 1650m x 483m METALLIZATION: TRANSISTOR COUNT: Type: Al, 1% Cu Thickness: 16kÅ 2kÅ 63 SUBSTRATE POTENTIAL (POWERED UP): PROCESS: V- Bipolar Dielectric Isolation Metallization Mask Layout HA-5137A BAL BAL -IN V+ +IN OUT V- FN2908 Rev 5.00 April 2000 NC Page 8 of 9 HA-5137A Ceramic Dual-In-Line Frit Seal Packages (CERDIP) F8.3A MIL-STD-1835 GDIP1-T8 (D-4, CONFIGURATION A) LEAD FINISH c1 8 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE -D- -A- BASE METAL (c) E M -Bbbb S C A-B S Q -C- SEATING PLANE S1 b2 b ccc M C A-B S D S eA/2 NOTES - 0.200 - 5.08 - 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 D - 0.405 - 10.29 5 E 0.220 0.310 5.59 7.87 5 eA e MAX b  A A MIN A A L MILLIMETERS MAX M (b) D BASE PLANE MIN b1 SECTION A-A D S INCHES SYMBOL c aaa M C A - B S D S NOTES: 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer’s identification shall not be used as a pin one identification mark. e 0.100 BSC 2.54 BSC - eA 0.300 BSC 7.62 BSC - eA/2 0.150 BSC 3.81 BSC - L 0.125 0.200 3.18 5.08 - Q 0.015 0.060 0.38 1.52 6 S1 0.005 - 0.13 - 7 105o 90o 105o - 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied.  90o aaa - 0.015 - 0.38 - 3. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. bbb - 0.030 - 0.76 - ccc - 0.010 - 0.25 - M - 0.0015 - 0.038 2, 3 4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial lead paddle. For this configuration dimension b3 replaces dimension b2. N 8 5. This dimension allows for off-center lid, meniscus, and glass overrun. 8 8 Rev. 0 4/94 6. Dimension Q shall be measured from the seating plane to the base plane. 7. Measure dimension S1 at all four corners. 8. N is the maximum number of terminal positions. 9. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 10. Controlling dimension: INCH © Copyright Intersil Americas LLC 2000. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN2908 Rev 5.00 April 2000 Page 9 of 9