0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
ISL31483EIBZ-T

ISL31483EIBZ-T

  • 厂商:

    RENESAS(瑞萨)

  • 封装:

    SOIC14

  • 描述:

    IC TRANSCEIVER FULL 1/1 14SOIC

  • 数据手册
  • 价格&库存
ISL31483EIBZ-T 数据手册
ISL31483E, ISL31485E DATASHEET NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT PART ISL32483E, ISL32485E Fault Protected, Extended CMR, RS-485/RS-422 Transceivers with Cable Invert The ISL31483E and ISL31485E are fault protected, 5V powered differential transceivers that exceed the RS-485 and RS-422 standards for balanced communication. The RS-485 transceiver pins (driver outputs and receiver inputs) are fault protected up to ±60V. Additionally, the extended common mode range allows these transceivers to operate in environments with common mode voltages up to ±25V (>2x the RS-485 requirement), making this fault protected RS-485 family one of the most robust on the market. Transmitters deliver an exceptional 2.5V (typical) differential output voltage into the RS-485 specified 54Ω load. This yields better noise immunity than standard RS-485 ICs, or allows up to six 120Ω terminations in star network topologies. Receiver (Rx) inputs feature a “Full Fail-Safe” design, which ensures a logic high Rx output if Rx inputs are floating, shorted, or on a terminated but undriven (idle) bus. The ISL31483E and ISL31485E include cable invert functions that reverse the polarity of the Rx and/or Tx bus pins in case the cable is misconnected. Unlike competing devices, Rx full fail-safe operation is maintained even when the Rx input polarity is switched. FN7638 Rev 4.00 May 13, 2015 Features • Fault protected RS-485 bus pins . . . . . . . . . . . . . . up to ±60V • Extended common mode range. . . . . . . . . . . . . . . . . . . . ±25V More than twice the range required for RS-485 • Cable invert pins corrects for reversed cable connections while maintaining Rx full fail-safe functionality • Full fail-safe (open, short, terminated) RS-485 receivers • 1/4 unit load (UL) for up to 128 devices on the bus • High Rx IOL for opto-couplers in isolated designs • Hot plug circuitry - Tx and Rx outputs remain three-state during power-up/power-down • Slew rate limited RS-485 data rate . . . . . . . . . . . . . . . 1Mbps • Low quiescent supply current. . . . . . . . . . . . . . . . . . . . 2.3mA • Ultra low shutdown supply current. . . . . . . . . . . . . . . . . . 10µA Applications • Utility meters/automated meter reading systems • High node count RS-485 systems • PROFIBUS™ and RS-485 based field bus networks and factory automation • Security camera networks • Building lighting and environmental control systems • Industrial/process control networks 30 COMMON MODE RANGE A 20 VOLTAGE (V) 25 VID = ±1V B 25 15 10 5 RO 0 12 0 -7 -12 -20 -25 -5 TIME (400ns/DIV) FIGURE 1. EXCEPTIONAL Rx OPERATES AT 1Mbps EVEN WITH ±25V COMMON MODE VOLTAGE FN7638 Rev 4.00 May 13, 2015 STANDARD RS-485 TRANSCEIVER CLOSEST COMPETITOR ISL3148XE FIGURE 2. TRANSCEIVERS DELIVER SUPERIOR COMMON MODE RANGE vs STANDARD RS-485 DEVICES Page 1 of 18 ISL31483E, ISL31485E Table of Contents Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Truth Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Typical Operating Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Thermal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Test Circuits and Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receiver (Rx) Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Driver (Tx) Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High Overvoltage (Fault) Protection Increases Ruggedness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Widest Common Mode Voltage (CMV) Tolerance Improves Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cable Invert (Polarity Reversal) Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High VOD Improves Noise Immunity and Flexibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hot Plug Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Rate, Cables and Terminations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Built-in Driver Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low Power Shutdown Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 11 11 11 11 11 12 12 12 12 13 Typical Performance Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Die Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 About Intersil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Package Outline Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 M14.15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 M8.15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 FN7638 Rev 4.00 May 13, 2015 Page 2 of 18 ISL31483E, ISL31485E TABLE 1. SUMMARY OF FEATURES PART NUMBER HALF/FULL DUPLEX DATA RATE (Mbps) SLEW-RATE LIMITED? ISL31483E Full 1 Yes Yes ISL31485E Half 1 Yes Tx Only POLARITY REVERSAL PINS? QUIESCENT ICC (mA) LOW POWER SHDN? PIN COUNT Yes Yes 2.3 Yes 14 Yes Yes 2.3 No 8 EN PINS? HOT PLUG Ordering Information PART NUMBER (Notes 1, 2, 3) PART MARKING TEMP. RANGE (°C) PACKAGE (RoHS Compliant) PKG. DWG. # ISL31483EIBZ ISL31483 EIBZ -40 to +85 14 Ld SOIC M14.15 ISL31485EIBZ 31485 EIBZ -40 to +85 8 Ld SOIC M8.15 NOTES: 1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pbfree products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see product information page for ISL31483E, ISL31485E. For more information on MSL, please see tech brief TB363 FN7638 Rev 4.00 May 13, 2015 Page 3 of 18 ISL31483E, ISL31485E Pin Configurations ISL31485E (8 LD SOIC) TOP VIEW ISL31483E (14 LD SOIC) TOP VIEW RINV 1 RO 2 R RE 3 DE 4 DI 5 D 14 VCC RO 1 13 VCC INV 2 12 A DE 3 11 B DI 4 R D 8 VCC 7 B/Z 6 A/Y 5 GND 10 Z GND 6 9 Y GND 7 8 DINV Pin Descriptions PIN NAME PIN # PIN # ISL31483E ISL31485E DESCRIPTION RO 2 1 Receiver output. If INV or RINV is low, then: If A - B  -10mV, RO is high; if A - B  -200mV, RO is low. If INV or RINV is high, then: If B - A  -10mV, RO is high; if B - A  -200mV, RO is low. In all cases, RO = High if A and B are unconnected (floating), or shorted together, or connected to an undriven, terminated bus (i.e., Rx is always failsafe open, shorted and idle, even if polarity is inverted). RE 3 - Receiver output enable. RO is enabled when RE is low; RO is high impedance when RE is high. Internally pulled low. DE 4 3 Driver output enable. The driver outputs, Y and Z, are enabled by bringing DE high and they are high impedance when DE is low. Internally pulled high to VCC. DI 5 4 Driver input. If INV or DINV is low, a low on DI forces output Y low and output Z high, while a high on DI forces output Y high and output Z low. The output states relative to DI invert if INV or DINV is high. GND 6, 7 5 Ground connection. A/Y - 6 ±60V Fault Protected RS-485/RS-422 level I/O pin. If INV is low, A/Y is the non-inverting receiver input and non-inverting driver output. If INV is high, A/Y is the inverting receiver input and the inverting driver output. Pin is an input if DE = 0; pin is an output if DE = 1. B/Z - 7 ±60V Fault Protected RS-485/RS-422 level I/O pin. If INV is low, B/Z is the inverting receiver input and inverting driver output. If INV is high, B/Z is the non-inverting receiver input and the non-inverting driver output. Pin is an input if DE = 0; pin is an output if DE = 1. A 12 - ±60V Fault Protected RS-485/RS-422 level input. If RINV is low, then A is the non-inverting receiver input. If RINV is high, then A is the inverting receiver input. B 11 - ±60V Fault Protected RS-485/RS-422 level input. If RINV is low, then B is the inverting receiver input. If RINV is high, then B is the non-inverting receiver input. Y 9 - ±60V Fault Protected RS-485/RS-422 level output. If DINV is low, then Y is the non-inverting driver output. If DINV is high, then Y is the inverting driver output. Z 10 - ±60V Fault Protected RS-485/RS-422 level. If DINV is low, then Z is the inverting driver output. If DINV is high, then Z is the non-inverting driver output. VCC 13, 14 8 System power supply input (4.5V to 5.5V). INV - 2 Receiver and driver polarity selection input. When driven high this pin swaps the polarity of the driver output and receiver input pins. If unconnected (floating) or connected low, normal RS-485 polarity conventions apply. Internally pulled low. RINV 1 - Receiver polarity selection input. When driven high this pin swaps the polarity of the receiver input pins. If unconnected (floating) or connected low, normal RS-485 polarity conventions apply. Internally pulled low. DINV 8 - Driver polarity selection input. When driven high this pin swaps the polarity of the driver output pins. If unconnected (floating) or connected low, normal RS-485 polarity conventions apply. Internally pulled low. FN7638 Rev 4.00 May 13, 2015 Page 4 of 18 ISL31483E, ISL31485E Truth Tables RECEIVING INPUTS TRANSMITTING INPUTS OUTPUTS OUTPUT RE DE (Half Duplex) DE (Full Duplex) A-B INV or RINV RO  -0.01V 0 1 RE DE DI INV or DINV Y Z 0 0 X X 1 1 0 1 0 0 0 X  -0.2V 0 0 0 0 X  0.01V 1 1 0 0 X  0.2V 1 0 0 0 X Inputs Open or Shorted X 1 1 0 0 X X High-Z* 1 1 1 X X High-Z X 1 0 0 0 1 X 1 1 1 0 1 X 1 0 1 1 0 0 0 X X High-Z High-Z 1 0 X X High-Z* High-Z* NOTE: *Low Power Shutdown Mode (See Note 11), except for ISL31485E. NOTE: *Low Power Shutdown Mode (See Note 11), except for ISL31485E. Typical Operating Circuits +5V +5V + 8 0.1µF 0.1µF + 8 VCC VCC 2 INV 1 RO R A/Y 6 B/Z 7 RT RT 7 B/Z 6 A/Y RO 1 R DE 3 3 DE 4 DI DI 4 D D GND GND 5 INV 2 5 NOTE: The IC on the left has the cable connections swapped, so the INV pin is strapped high to invert its Rx and Tx polarity. FIGURE 3. ISL31485E HALF DUPLEX EXAMPLE +5V +5V + 13, 14 1 RINV 2 RO VCC R B 11 0.1µF 0.1µF RT + 13, 14 VCC 9 Y A 12 D 10 Z 3 RE DE 4 4 DE 5 DI 8 DI 5 Y 9 Z 10 D DINV RT RE 3 11 B 12 A GND GND R RO 2 RINV DINV 1 8 6, 7 6, 7 NOTE: The IC on the left has the cable connections swapped, so the INV pins (1, 8) are strapped high to invert its Rx and Tx polarity. FIGURE 4. ISL31483E FULL DUPLEX EXAMPLE FN7638 Rev 4.00 May 13, 2015 Page 5 of 18 ISL31483E, ISL31485E Absolute Maximum Ratings Thermal Information VCC to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V Input Voltages DI, INV, RINV, DINV, DE, RE. . . . . . . . . . . . . . . . . . . . -0.3V to (VCC + 0.3V) Input/Output Voltages A/Y, B/Z, A, B, Y, Z. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±60V A/Y, B/Z, A, B, Y, Z (Transient Pulse Through 100Ω, Note 15). . . . ±80V RO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (VCC +0.3V) Short-circuit Duration Y, Z. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Specification Table Latch-up per JESD78, Level 2, Class A . . . . . . . . . . . . . . . . . . . . . . . +125°C Thermal Resistance (Typical) JA (°C/W) JC (°C/W) 8 Ld SOIC Package (Notes 4, 5). . . . . . . . . . 104 47 14 Ld SOIC Package (Notes 4, 5) . . . . . . . . 78 42 Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . . . . . . -65°C to +150°C Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .see TB493 Recommended Operating Conditions Supply Voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C Bus Pin Common Mode Voltage Range . . . . . . . . . . . . . . . . . -25V to +25V CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 5. For JC, the “case temp” location is taken at the package top center. Electrical Specifications Test Conditions: VCC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at VCC = 5V, TA = +25°C (Note 6). Boldface limits apply across the operating temperature range, -40°C to +85°C. PARAMETER TEMP (°C) MIN (Note 14) TYP MAX (Note 14) UNIT Full - - VCC V RL = 100Ω (RS-422) Full 2.4 3.2 - V SYMBOL TEST CONDITIONS DC CHARACTERISTICS Driver Differential VOUT (No load) VOD1 Driver Differential VOUT (Loaded, Figure 5A) VOD2 Change in Magnitude of Driver Differential VOUT for Complementary Output States VOD Driver Differential VOUT with Common Mode Load (Figure 5B) VOD3 Driver Common-Mode VOUT (Figure 5) VOC RL = 54Ω (RS-485) Full 1.5 2.5 VCC V RL = 54Ω (PROFIBUS, VCC ≥ 5V) Full 2.0 2.5 - V RL = 21Ω (Six 120Ω terminations for Star Configurations, VCC ≥ 4.75V) Full 0.8 1.3 - V RL = 54Ω or 100Ω (Figure 5A) Full - - 0.2 V RL = 60Ω, -7V ≤ VCM ≤ 12V Full 1.5 2.1 VCC RL = 60Ω, -25V ≤ VCM ≤ 25V (VCC ≥ 4.75V) Full 1.7 2.3 RL = 21Ω, -15V ≤ VCM ≤ 15V (VCC ≥ 4.75V) Full 0.8 1.1 - V RL = 54Ω or 100Ω Full -1 - 3 V V V RL = 60Ω or 100Ω, -20V ≤ VCM ≤ 20V Full -2.5 - 5 V Change in Magnitude of Driver Common-mode VOUT for Complementary Output States DVOC RL = 54Ω or 100Ω (Figure 5A) Full - - 0.2 V Driver Short-circuit Current IOSD DE = VCC, -25V ≤ VO ≤ 25V (Note 8) Full -250 - 250 mA IOSD1 At first fold-back, 22V ≤ VO ≤ -22V Full -83 83 mA IOSD2 At second fold-back, 35V ≤ VO ≤ -35V Full -13 13 mA Logic Input High Voltage VIH DE, DI, RE, INV, RINV, DINV Full 2.5 - - V Logic Input Low Voltage VIL DE, DI, RE, INV, RINV, DINV Full - - 0.8 V Logic Input Current IIN1 DI Full -1 - 1 µA DE, RE, INV, RINV, DINV Full -15 6 15 µA FN7638 Rev 4.00 May 13, 2015 Page 6 of 18 ISL31483E, ISL31485E Electrical Specifications Test Conditions: VCC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at VCC = 5V, TA = +25°C (Note 6). Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued) PARAMETER Input/Output Current (A/Y, B/Z) Input Current (A, B) (Full Duplex Versions Only) Output Leakage Current (Y, Z) (Full Duplex Versions Only) Receiver Differential Threshold Voltage Receiver Input Hysteresis Receiver Output High Voltage SYMBOL IIN2 TEST CONDITIONS MIN (Note 14) TYP MAX (Note 14) UNIT VIN = 12V Full - 110 250 µA VIN = -7V Full -200 -75 - µA VIN = ±25V Full -800 ±240 800 µA VIN = ±60V (Note 17) Full -6 ±0.7 6 mA VIN = 12V Full - 90 125 µA VIN = -7V Full -100 -70 - µA VIN = ±25V Full -500 ±200 500 µA VIN = ±60V (Note 17) Full -3 ±0.5 3 mA VIN = 12V Full - 20 200 µA VIN = -7V Full -100 -5 - µA VIN = ±25V Full -500 ±40 500 µA VIN = ±60V (Note 17) Full -3 ±0.15 3 mA A-B if INV or RINV = 0; B-A if INV or RINV = 1, -25V ≤ VCM ≤ 25V Full -200 -100 -10 mV V TH -25V ≤ VCM ≤ 25V 25 - 25 - mV VOH1 VID = -10mV IO = -2mA Full VCC - 0.5 4.75 - V IO = -8mA Full 2.8 4.2 - V IIN3 IOZD V TH DE = 0V, VCC = 0V or 5.5V TEMP (°C) VCC = 0V or 5.5V RE = 0V, DE = 0V, VCC = 0V or 5.5V VOH2 Receiver Output Low Voltage VOL IO = 6mA, VID = -200mV Full - 0.27 0.4 V Receiver Output Low Current IOL VO = 1V, VID = -200mV Full 15 22 - mA Three-state (High Impedance) Receiver Output Current IOZR 0V ≤ VO ≤ VCC (Note 16) Full -1 0.01 1 µA Receiver Short-circuit Current IOSR 0V ≤ VO ≤ VCC Full ±12 - ±110 mA DE = VCC, RE = 0V or VCC, DI = 0V or VCC Full - 2.3 4.5 mA DE = 0V, RE = VCC, DI = 0V or VCC (Note 16) Full - 10 50 µA Human Body Model (Tested per JESD22-A114E) 25 - ±2 - kV Machine Model (Tested per JESD22-A115-A) 25 - ±700 - V Full - 70 125 ns SUPPLY CURRENT No-load Supply Current (Note 7) Shutdown Supply Current ICC ISHDN ESD PERFORMANCE All Pins DRIVER SWITCHING CHARACTERISTICS Driver Differential Output Delay tPLH, tPHL RD = 54Ω, CD = 50pF No CM Load (Figure 6) -25V ≤ VCM ≤ 25V Driver Differential Output Skew tSKEW RD = 54Ω, CD = 50pF No CM Load (Figure 6) -25V ≤ VCM ≤ 25V (Note 18) Driver Differential Rise or Fall Time tR, tF Maximum Data Rate fMAX RD = 54Ω, CD = 50pF No CM Load (Figure 6) -25V ≤ VCM ≤ 25V Full - - 350 ns Full - 4.5 15 ns Full - - 25 ns Full 70 170 300 ns Full 70 - 550 ns CD = 820pF (Figure 8) Full 1 4 - Mbps tZH SW = GND (Figure 7), (Note 9) Full - - 350 ns Driver Enable to Output Low tZL SW = VCC (Figure 7), (Note 9) Full - - 300 ns Driver Disable from Output Low tLZ SW = VCC (Figure 7) Full - - 120 ns Driver Enable to Output High FN7638 Rev 4.00 May 13, 2015 Page 7 of 18 ISL31483E, ISL31485E Electrical Specifications Test Conditions: VCC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at VCC = 5V, TA = +25°C (Note 6). Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued) PARAMETER Driver Disable from Output High Time to Shutdown TEMP (°C) MIN (Note 14) TYP MAX (Note 14) UNIT SW = GND (Figure 7) Full - - 120 ns SYMBOL tHZ tSHDN TEST CONDITIONS (Notes 11, 16) Full 60 160 600 ns Driver Enable from Shutdown to Output High tZH(SHDN) SW = GND (Figure 7), (Notes 11, 12, 16) Full - - 2000 ns Driver Enable from Shutdown to Output Low tZL(SHDN) SW = VCC (Figure 7), (Notes 11, 12, 16) Full - - 2000 ns RECEIVER SWITCHING CHARACTERISTICS Maximum Data Rate fMAX -25V ≤ VCM ≤ 25V (Figure 9) Full 1 15 - Mbps -15V ≤ VCM ≤ 15V (Figure 9) Full 1 12 - Mbps -25V ≤ VCM ≤ 25V (Figure 9) Full - 90 150 ns (Figure 9) Full - 4 10 ns Receiver Input to Output Delay tPLH, tPHL Receiver Skew | tPLH - tPHL | tSKD Receiver Enable to Output Low tZL RL = 1kΩ, CL = 15pF, SW = VCC (Figure 10), (Notes 10, 16) Full - - 50 ns Receiver Enable to Output High tZH RL = 1kΩ, CL = 15pF, SW = GND (Figure 10), (Notes 10, 16) Full - - 50 ns Receiver Disable from Output Low tLZ RL = 1kΩ, CL = 15pF, SW = VCC (Figure 10) (Note 16) Full - - 50 ns Receiver Disable from Output High tHZ RL = 1kΩ, CL = 15pF, SW = GND (Figure 10) (Note 16) Full - - 50 ns (Notes 11, 16) Full 60 160 600 ns Receiver Enable from Shutdown to Output High tZH(SHDN) RL = 1kΩ, CL = 15pF, SW = GND (Figure 10), (Notes 11, 13, 16) Full - - 2000 ns Receiver Enable from Shutdown to Output Low tZL(SHDN) RL = 1kΩ, CL = 15pF, SW = VCC (Figure 10), (Notes 11, 13, 16) Full - - 2000 ns Time to Shutdown tSHDN NOTES: 6. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise specified. 7. Supply current specification is valid for loaded drivers when DE = 0V. 8. Applies to peak current. See “Typical Performance Curves” beginning on page 14 for more information 9. Keep RE = 0 to prevent the device from entering SHDN. 10. The RE signal high time must be short enough (typically 600ns to ensure that the device enters SHDN. 13. Set the RE signal high time >600ns to ensure that the device enters SHDN. 14. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. 15. Tested according to TIA/EIA-485-A, Section 4.2.6 (±80V for 15ms at a 1% duty cycle). 16. Does not apply to the ISL31485E. The ISL31485E has no Rx enable function and thus no SHDN function. 17. See “Caution” statement under the “Recommended Operating Conditions” section on page 6. 18. This parameter is not production tested. FN7638 Rev 4.00 May 13, 2015 Page 8 of 18 ISL31483E, ISL31485E Test Circuits and Waveforms VCC RL/2 DE Z DI Z DI VOD D 375Ω RL/2 DE VCC VCM VOD D Y Y VOC RL/2 VOC RL/2 375Ω FIGURE 5B. VOD AND VOC WITH COMMON MODE LOAD FIGURE 5A. VOD AND VOC FIGURE 5. DC DRIVER TEST CIRCUITS 3V DI 50% 50% 0V VCC tPHL tPLH 375Ω* DE OUT (Z) VOH OUT (Y) VOL Z DI CD D RD Y SIGNAL GENERATOR VCM 375Ω* DIFF OUT (Y - Z) *ONLY USED FOR COMMON MODE LOAD TESTS 90% +VOD 90% 10% 10% tR -VOD tF SKEW = |tPLH - tPHL| FIGURE 6A. TEST CIRCUIT FIGURE 6B. MEASUREMENT POINTS FIGURE 6. DRIVER PROPAGATION DELAY AND DIFFERENTIAL TRANSITION TIMES DE Z DI 110Ω VCC D SIGNAL GENERATOR SW Y GND CL 3V DE (Note 11) tZH, tZH(SHDN) (Note 11) PARAMETER OUTPUT RE DI SW CL (pF) tHZ Y/Z X 1/0 GND 50 tLZ Y/Z X 0/1 VCC 50 tZH Y/Z 0 (Note 9) 1/0 GND 100 tZL Y/Z 0 (Note 9) 0/1 VCC 100 tZH(SHDN) Y/Z 1 (Note 12) 1/0 GND 100 tZL(SHDN) Y/Z 1 (Note 12) 0/1 VCC 100 FIGURE 7A. TEST CIRCUIT 50% 50% 0V tHZ OUTPUT HIGH VOH - 0.5V 2.3V OUT (Y, Z) VOH 0V tZL, tZL(SHDN) tLZ (Note 11) VCC OUT (Y, Z) 2.3V VOL + 0.5V OUTPUT LOW VOL FIGURE 7B. MEASUREMENT POINTS FIGURE 7. DRIVER ENABLE AND DISABLE TIMES FN7638 Rev 4.00 May 13, 2015 Page 9 of 18 ISL31483E, ISL31485E Test Circuits and Waveforms (Continued) VCC DE 3V + Z DI 54Ω D DI VOD CD Y 0V - SIGNAL GENERATOR +VOD DIFF OUT (Y - Z) -VOD FIGURE 8A. TEST CIRCUIT 0V FIGURE 8B. MEASUREMENT POINTS FIGURE 8. DRIVER DATA RATE RE R A SIGNAL GENERATOR B 15pF B VCM + 750mV VCM RO VCM VCM - 750mV A tPLH SIGNAL GENERATOR tPHL VCC 50% RO VCM 50% 0V FIGURE 9B. MEASUREMENT POINTS FIGURE 9A. TEST CIRCUIT FIGURE 9. RECEIVER PROPAGATION DELAY AND DATA RATE (Note 11) RE 3V B A 1kΩ RO R SIGNAL GENERATOR 15pF VCC SW RE 50% 0V GND tZH, tZH(SHDN) (Note 11) DE A SW tHZ 0 +1.5V GND tLZ 0 -1.5V VCC (Note 11) tZH (Note 10) 0 +1.5V GND RO tZL (Note 10) 0 -1.5V VCC tZH(SHDN) (Note 13) 0 +1.5V GND tZL(SHDN) (Note 13) 0 -1.5V VCC FIGURE 10A. TEST CIRCUIT tHZ OUTPUT HIGH VOH - 0.5V 1.5V RO PARAMETER 50% VOH 0V tZL, tZL(SHDN) tLZ VCC 1.5V VOL + 0.5V OUTPUT LOW VOL FIGURE 10B. MEASUREMENT POINTS FIGURE 10. RECEIVER ENABLE AND DISABLE TIMES FN7638 Rev 4.00 May 13, 2015 Page 10 of 18 ISL31483E, ISL31485E Application Information The RS-485 and RS-422 are differential (balanced) data transmission standards used for long haul or noisy environments. The RS-422 is a subset of RS-485, so RS-485 transceivers are also RS-422 compliant. The RS-422 is a point-to-multipoint (multidrop) standard, which allows only one driver and up to 10 (assuming one unit load devices) receivers on each bus. The RS-485 is a true multipoint standard, which allows up to 32 one unit load devices (any combination of drivers and receivers) on each bus. To allow for multipoint operation, the RS-485 specification requires that drivers must handle bus contention without sustaining any damage. Another important advantage of RS-485 is the extended Common Mode Range (CMR), which specifies that the driver outputs and receiver inputs withstand signals that range from +12V to -7V. The RS-422 and RS-485 are intended for runs as long as 4000, so the wide CMR is necessary to handle ground potential differences, as well as voltages induced in the cable by external fields. The ISL3148xE is a family of ruggedized RS-485 transceivers that improves on the RS-485 basic requirements and therefore increases system reliability. The CMR increases to ±25V, while the RS-485 bus pins (receiver inputs and driver outputs) include fault protection against voltages and transients up to ±60V. Additionally, larger than required differential output voltages (VOD) increase noise immunity. Receiver (Rx) Features These devices utilize a differential input receiver for maximum noise immunity and common mode rejection. Input sensitivity is better than ±200mV, as required by the RS-422 and RS-485 specifications. Receiver input (load) current surpasses the RS-422 specification of 3mA and is four times lower than the RS-485 “Unit Load (UL)” requirement of 1mA maximum. Thus, these products are known as “one-quarter UL” transceivers and there can be up to 128 of these devices on a network while still complying with the RS-485 loading specification. The Rx functions with common mode voltages as great as ±25V, making them ideal for industrial, or long networks where induced voltages are a realistic concern. All the receivers include a “full fail-safe” function that guarantees a high level receiver output if the receiver inputs are unconnected (floating), shorted together, or connected to a terminated bus with all the transmitters disabled (i.e., an idle bus). Rx outputs feature high drive levels (typically 22mA at VOL = 1V) to ease the design of optically coupled isolated interfaces. Except for the ISL31485E, Rx outputs are three-statable via the active low RE input. The Rx includes noise filtering circuitry to reject high frequency signals and typically rejects pulses narrower than 50ns (equivalent to 20Mbps). FN7638 Rev 4.00 May 13, 2015 Driver (Tx) Features The RS-485/RS-422 driver is a differential output device that delivers at least 1.5V across a 54Ω load (RS-485) and at least 2.4V across a 100Ω load (RS-422). The drivers feature low propagation delay skew to maximize bit width and to minimize EMI and all drivers are three-statable via the active high DE input. The driver outputs are slew rate limited to minimize EMI and to minimize reflections in unterminated or improperly terminated networks. High Overvoltage (Fault) Protection Increases Ruggedness The ±60V (referenced to the IC GND) fault protection on the RS-485 pins, makes these transceivers some of the most rugged on the market. This level of protection makes the ISL3148xE perfect for applications where power (e.g., 24V and 48V supplies) must be routed in the conduit with the data lines, or for outdoor applications where large transients are likely to occur. When power is routed with the data lines, even a momentary short between the supply and data lines will destroy an unprotected device. The ±60V fault levels of this family are at least five times higher than the levels specified for standard RS-485 ICs. The ISL3148xE protection is active whether the Tx is enabled or disabled and even if the IC is powered down. If transients or voltages (including overshoots and ringing) greater then ±60V are possible, then additional external protection is required. Widest Common Mode Voltage (CMV) Tolerance Improves Operating Range The RS-485 networks operating in industrial complexes, or over long distances, are susceptible to large CMV variations. Either of these operating environments may suffer from large node-to-node ground potential differences, or CMV pickup from external electromagnetic sources and devices with only the minimum required +12V to -7V CMR may malfunction. The ISL3148xE’s extended ±25V CMR is the widest available, allowing operation in environments that would overwhelm lesser transceivers. Additionally, the Rx will not phase invert (erroneously change state) even with CMVs of ±40V, or differential voltages as large as 40V. Cable Invert (Polarity Reversal) Function With large node count RS-485 networks, it is common for some cable data lines to be wired backwards during installation. When this happens the node is unable to communicate over the network. Once a technician finds the miswired node, he must then rewire the connector which is time consuming. The ISL31483E and ISL31485E simplify this task by including cable invert pins (INV, DINV, RINV) that allow the technician to invert the polarity of the Rx input and/or the Tx output pins simply by moving a jumper to change the state of the invert pin(s). When the invert pin(s) is low, the IC operates like any standard RS-485 transceiver and the bus pins have their normal polarity definition of A and Y being noninverting and B and Z being inverting. With the invert pin high, the corresponding bus Page 11 of 18 ISL31483E, ISL31485E pins reverse their polarity, so B and Z are now noninverting and A and Y become inverting. High VOD Improves Noise Immunity and Flexibility The ISL3148xE driver design delivers larger differential output voltages (VOD) than the RS-485 standard requires, or than most RS-485 transmitters can deliver. The typical ±2.5V VOD provides more noise immunity than networks built using many other transceivers. Another advantage of the large VOD is the ability to drive more than two bus terminations, which allows for utilizing the ISL3148xE in “star” and other multi-terminated, nonstandard network topologies. Figure 12, details the transmitter’s VOD vs IOUT characteristic and includes load lines for four (30Ω) and six (20Ω) 120Ω terminations. Figure 12 shows that the driver typically delivers ±1.3V into six terminations and the “Electrical Specification” on page 6 guarantees a VOD of ±0.8V at 21Ω over the full temperature range. The RS-485 standard requires a minimum 1.5V VOD into two terminations, but the ISL3148xE deliver RS-485 voltage levels with 2x to 3x the number of terminations. Hot Plug Function When a piece of equipment powers up, there is a period of time where the processor or ASIC driving the RS-485 control lines (DE, RE) is unable to ensure that the RS-485 Tx and Rx outputs are kept disabled. If the equipment is connected to the bus, a driver activating prematurely during power-up may crash the bus. To avoid this scenario, the ISL3148xE devices incorporate a “Hot Plug” function. Circuitry monitoring VCC ensures that, during power-up and power-down, the Tx and Rx outputs remain disabled, regardless of the state of DE and RE, if VCC is less than ≈3.5V. This gives the processor/ASIC a chance to stabilize and drive the RS-485 control lines to the proper states. Figure 11 illustrates the power-up and power-down performance of the ISL3148xE compared to an RS-485 IC without the Hot Plug feature. FN7638 Rev 4.00 May 13, 2015 2.5 VCC VCC (V) 2.8V 5.0 0 5.0 RL = 1kΩ 2.5 0 A/Y ISL3148XE RL = 1kΩ RO ISL3148XE 5.0 2.5 0 TIME (40µs/DIV) RECEIVER OUTPUT (V) The full duplex ISL31483E includes two invert pins that allow for separate control of the Rx and Tx polarities. If only the Rx cable is miswired, then only the RINV pin need be driven to a logic 1. If the Tx cable is miswired, then DINV must be connected to a logic high. The two half duplex versions have only one logic pin (INV) that, when high, switches the polarity of both the Tx and the Rx blocks. RE = GND 3.5V DRIVER Y OUTPUT (V) Intersil’s unique cable invert function is superior to that found on competing devices because the Rx full failsafe function is maintained even when the Rx polarity is reversed. Competitor devices implement the Rx invert function simply by inverting the Rx output. This means that with the Rx inputs floating or shorted together, the Rx appropriately delivers a logic 1 in normal polarity, but outputs a logic low when the IC is operated in the inverted mode. Intersil’s innovative Rx design guarantees that with the Rx inputs floating, or shorted together (VID = 0V), the Rx output remains high regardless of the state of the invert pins. DE, DI = VCC FIGURE 11. HOT PLUG PERFORMANCE ISL3148XE vs ISL83088E WITHOUT HOT PLUG CIRCUITRY Data Rate, Cables and Terminations The RS-485/RS-422 are intended for network lengths up to 4000, but the maximum system data rate decreases as the transmission length increases. These 1Mbps versions can operate at full data rates with lengths up to 800’ (244m). Jitter is the limiting parameter at this data rate, so employing encoded data streams (e.g., Manchester coded or Return to Zero) may allow increased transmission distances. Twisted pair is the cable of choice for RS-485/RS-422 networks. Twisted pair cables tend to pick up noise and other electromagnetically induced voltages as common mode signals, which are effectively rejected by the differential receivers in these ICs. Proper termination is imperative to minimize reflections and terminations are recommended unless power dissipation is an overriding concern. In point-to-point, or point-to-multipoint (single driver on bus like RS-422) networks, the main cable should be terminated in its characteristic impedance (typically 120Ω) at the end farthest from the driver. In multi-receiver applications, stubs connecting receivers to the main cable should be kept as short as possible. Multipoint (multi-driver) systems require that the main cable be terminated in its characteristic impedance at both ends. Stubs connecting a transceiver to the main cable should be kept as-short-as possible. Built-in Driver Overload Protection As stated previously, the RS-485 specification requires that drivers survive worst case bus contentions undamaged. These transceivers meet this requirement via driver output short-circuit current limits and on-chip thermal shutdown circuitry. The driver output stages incorporate a double foldback short-circuit current limiting scheme which ensures that the output current never exceeds the RS-485 specification, even at the common mode and fault condition voltage range extremes. The first foldback current level (≈70mA) is set to ensure that the driver never folds back when driving loads with common mode voltages up to ±25V. The very low second foldback current setting (≈9mA) minimizes power dissipation if the Tx is enabled when a fault occurs. Page 12 of 18 ISL31483E, ISL31485E In the event of a major short-circuit condition, devices also include a thermal shutdown feature that disables the drivers whenever the die temperature becomes excessive. This eliminates the power dissipation, allowing the die to cool. The drivers automatically reenable after the die temperature drops about 15°C. If the contention persists, the thermal shutdown/re-enable cycle repeats until the fault is cleared. Receivers stay operational during thermal shutdown. Low Power Shutdown Mode These CMOS transceivers all use a fraction of the power required by competitive devices, but they also include a shutdown feature (except the ISL31485E) that reduces the already low quiescent ICC to a 10µA trickle. These devices enter shutdown whenever the receiver and driver are simultaneously disabled (RE = VCC and DE = GND) for a period of at least 600ns. Disabling both the driver and the receiver for less than 60ns guarantees that the transceiver will not enter shutdown. Note that receiver and driver enable times increase when the transceiver enables from shutdown. Refer to Notes 9, 10, 11, 12 and 13, at the end of the “Electrical Specification” table on page 8, for more information. FN7638 Rev 4.00 May 13, 2015 Page 13 of 18 ISL31483E, ISL31485E Typical Performance Curves VCC = 5V, TA = +25°C; Unless Otherwise Specified. 3.6 80 DIFFERENTIAL OUTPUT VOLTAGE (V) DRIVER OUTPUT CURRENT (mA) 90 RD = 30Ω 70 RD = 54Ω 60 +25°C +85°C 50 40 RD = 100Ω 30 20 10 0 0 1 2 3 4 DIFFERENTIAL OUTPUT VOLTAGE (V) 3.4 RD = 100Ω 3.2 3.0 2.8 RD = 54Ω 2.6 2.4 2.2 -40 5 FIGURE 12. DRIVER OUTPUT CURRENT vs DIFFERENTIAL OUTPUT VOLTAGE -25 0 25 50 TEMPERATURE (°C) 75 85 FIGURE 13. DRIVER DIFFERENTIAL OUTPUT VOLTAGE vs TEMPERATURE 150 2.45 +85°C 2.40 100 DE = VCC, RE = X OUTPUT CURRENT (mA) 2.35 ICC (mA) 2.30 2.25 DE = GND, RE = GND 2.20 2.15 2.10 -25 0 25 50 TEMPERATURE (°C) 75 -50 +25°C Y OR Z = HIGH +85°C 0 10 20 30 40 50 OUTPUT VOLTAGE (V) FIGURE 15. DRIVER OUTPUT CURRENT vs SHORT-CIRCUIT VOLTAGE 800 70 60 600 VOL, +25°C 50 BUS PIN CURRENT (µA) RECEIVER OUTPUT CURRENT (mA) 0 -150 -60 -50 -40 -30 -20 -10 85 FIGURE 14. SUPPLY CURRENT vs TEMPERATURE VOL, +85°C 40 30 20 10 0 -10 VOH, +85°C VOH, +25°C 0 1 2 3 4 5 RECEIVER OUTPUT VOLTAGE (V) FIGURE 16. RECEIVER OUTPUT CURRENT vs RECEIVER OUTPUT VOLTAGE FN7638 Rev 4.00 May 13, 2015 400 200 Y or Z 0 -200 A/Y or B/Z -400 -20 -30 +25°C -100 2.05 2.00 -40 Y OR Z = LOW 50 -600 -70 -50 -30 -10 0 10 30 50 70 BUS PIN VOLTAGE (V) FIGURE 17. BUS PIN CURRENT vs BUS PIN VOLTAGE Page 14 of 18 60 ISL31483E, ISL31485E Typical Performance Curves VCC = 5V, TA = +25°C; Unless Otherwise Specified. (Continued) 4.0 85 RD = 54Ω, CD = 50pF RD = 54Ω, CD = 50pF PROPAGATION DELAY (ns) 80 3.5 70 SKEW (ns) 75 tPLH 65 3.0 tPHL 60 2.5 55 |tPLH - tPHL| 75 85 VOLTAGE (V) FIGURE 18. DRIVER DIFFERENTIAL PROPAGATION DELAY vs TEMPERATURE 25 20 15 10 5 0 5 0 -5 -10 -15 -20 -25 A B VID = ±1V RO RO A B TIME (400ns/DIV) FIGURE 20. RECEIVER PERFORMANCE WITH ±25V CMV 0 50 25 TEMPERATURE (°C) -25 FIGURE 19. DRIVER DIFFERENTIAL SKEW vs TEMPERATURE RD = 54Ω, CD = 50pF 5 DI 0 5 0 3 2 1 0 -1 -2 -3 RO A/Y - B/Z TIME (400ns/DIV) FIGURE 21. DRIVER AND RECEIVER WAVEFORMS Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): GND PROCESS: Si Gate BiCMOS FN7638 Rev 4.00 May 13, 2015 85 75 Page 15 of 18 DRIVER INPUT (V) 25 0 50 TEMPERATURE (°C) RECEIVER OUTPUT (V) -25 2.0 -40 DRIVER OUTPUT (V) 50 -40 ISL31483E, ISL31485E Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest Rev. DATE REVISION CHANGE May 13, 2015 FN7638.4 Changed "MAX" on “Driver Differential Rise or Fall Time” on page 7 from 400 to 550. February 9, 2015 FN7638.3 Removed references to '480E and '486E in title and rest of document. Description on page 1, removed the last paragraph ("The '480E and '486E feature a logic . . . ") Under "Features", in the 3rd bullet removed references to '480E and removed the 4th bullet ("Logic Supply (VL) . . . ") On page 4, removed the '480E (col 2) and '486E (cols 5, 6, 7) entries from the "Pin Description" table and removed the "VL" "PD" and "NC" rows from this table. On page 6, removed row labeled "RO (480E, 496E)" in "Abs Max" table, removed all three 10 and 12 LD pkg entries from the "Thermal Info" section, removed Notes 5 and 7 and renumber all notes and note references. Stamped data sheet "Not recommended for New Designs. For an exact replacement, please see the ISL32483E, ISL32485E Series data sheet". Removed MSOP and TDFN from “Thermal Information” and (2) PODs. Thermal Information on page 6: 8 Ld SOIC Package, changed theta JA from 116 to 104. Thermal Information on page 6: 14 Ld SOIC Package, changed theta JA from 88 to 78 and theta JC from 38 to 42. On page 3, in Table 1 and the "Ordering Information " table, removed the devices marked "Coming Soon" (480E and 486E versions). Also removed unneeded PODs. January 7, 2011 FN7638.2 Changed Note 17 to Note 15 in “Absolute Maximum Ratings” on page 6 Changed Notes 10 and 13 to Notes 9 and 12 in Figure 7A on page 9 Changed Note 14 to Note 13 in Figure 10A on page 10 Deleted Note 17 (See Figure 9 for more information and for performance over-temperature) Changed TYP on “Driver Differential Rise or Fall Time” on page 7 from 230 to 170 Added Figure 15 “DRIVER OUTPUT CURRENT vs SHORT-CIRCUIT VOLTAGE” Updated “Package Outline Drawing” on page 18. Updated to new POD format by removing table and moving dimensions onto drawing and adding land pattern. September 8, 2010 FN7638.1 Corrected test conditions for “Receiver Output High Voltage” for “VOH5” on page 7 from “IO = -500mA” to “IO = -500µA” Jun 25, 2010 FN7638.0 Initial Release About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support © Copyright Intersil Americas LLC 2010-2015. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN7638 Rev 4.00 May 13, 2015 Page 16 of 18 ISL31483E, ISL31485E Package Outline Drawing M14.15 14 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 1, 10/09 8.65 A 3 4 0.10 C A-B 2X 6 14 DETAIL"A" 8 0.22±0.03 D 6.0 3.9 4 0.10 C D 2X 0.20 C 2X 7 PIN NO.1 ID MARK 5 0.31-0.51 B 3 (0.35) x 45° 4° ± 4° 6 0.25 M C A-B D TOP VIEW 0.10 C 1.75 MAX H 1.25 MIN 0.25 GAUGE PLANE C SEATING PLANE 0.10 C 0.10-0.25 1.27 SIDE VIEW (1.27) DETAIL "A" (0.6) NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to ASME Y14.5m-1994. 3. Datums A and B to be determined at Datum H. (5.40) 4. Dimension does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed 0.25mm per side. 5. The pin #1 identifier may be either a mold or mark feature. (1.50) 6. Does not include dambar protrusion. Allowable dambar protrusion shall be 0.10mm total in excess of lead width at maximum condition. 7. Reference to JEDEC MS-012-AB. TYPICAL RECOMMENDED LAND PATTERN FN7638 Rev 4.00 May 13, 2015 Page 17 of 18 ISL31483E, ISL31485E Package Outline Drawing M8.15 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 4, 1/12 DETAIL "A" 1.27 (0.050) 0.40 (0.016) INDEX 6.20 (0.244) 5.80 (0.228) AREA 0.50 (0.20) x 45° 0.25 (0.01) 4.00 (0.157) 3.80 (0.150) 1 2 8° 0° 3 0.25 (0.010) 0.19 (0.008) SIDE VIEW “B” TOP VIEW 2.20 (0.087) SEATING PLANE 5.00 (0.197) 4.80 (0.189) 1.75 (0.069) 1.35 (0.053) 1 8 2 7 0.60 (0.023) 1.27 (0.050) 3 6 4 5 -C- 1.27 (0.050) 0.51(0.020) 0.33(0.013) SIDE VIEW “A 0.25(0.010) 0.10(0.004) 5.20(0.205) TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensioning and tolerancing per ANSI Y14.5M-1994. 2. Package length does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 3. Package width does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 4. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 5. Terminal numbers are shown for reference only. 6. The lead width as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 7. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 8. This outline conforms to JEDEC publication MS-012-AA ISSUE C. FN7638 Rev 4.00 May 13, 2015 Page 18 of 18
ISL31483EIBZ-T 价格&库存

很抱歉,暂时无法提供与“ISL31483EIBZ-T”相匹配的价格&库存,您可以联系我们找货

免费人工找货